SPIDER ST1 Manual

Charging

Tap the Jog Dial and Phone Button.

Volume Adjustment

Increase/Decrease the volume : Rotate the Jog Dial clockwise or counterclockwise

Battery Check

Initially Pairing the SPIDER ST1

The headset will automatically enter the phone pairing mode

when you initially turn on the headset or in the following

situation:

• Rebooting after executing Factory Reset

1. Press and hold the Jog Dial and Phone Button for 1 second.

2. Search for Bluetooth devices on your mobile phone. Select the SPIDER ST1 in the list of the

devices detected on the mobile phone.

Play or pause music: Press and hold the Jog Dial for 1 second.

Track forward/ back: Rotate while pressing the Jog Dial clockwise or counterclockwise.

Mobile Phone Call Making and Answering

Answering a call: Tap the Phone Button

Ending a call: Tap the Phone Button

Voice dial: Tap the Phone Button

Speed dial: Double tap the Phone Button

Rejecting a call: Press and hold the Jog Dial for 2 seconds.

Radio On/Off

Turn on the FM radio: Press the Phone Button for 1 second.

Turn off the FM radio: Press the Phone Button for 1 second.

Radio Scan Up FM Band

Start scanning: Double tap the Phone Button

Stop scanning: Double tap the Phone Button

Radio Seek Stations

Seek up/down stations: Rotate while pressing the Jog Dial clockwise or counterclockwise.

Setting

Configuration Menu: Press the Jog Dial for 10 seconds.

Using the Sena Device Manager

Troubleshooting

Factory Reset

If you want to restore the headset to factory default settings, use the Factory Reset in the configuration

menu. The headset automatically restores the default settings and turns off.

operation.

This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to

part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment on and off, the user is encouraged to try to correct the interference by

one or more of the following measures:

-Reorient or relocate the receiving antennae

users must follow the specific operating instructions for satisfying RF exposure compliance. The antenna

used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in

accordance with FCC multi-transmitter product procedures.

When equipped, the distance between antenna and one’s head surface is 40.5mm.

FCC Caution

Any changes or modifications to the equipment not expressly approved by the party responsible for

compliance could void user’s authority to operate the equipment.

Certification et homologation de sécurité Déclaration de conformité FCC

Cet appareil est en conformité avec la partie 15 des règles de la FCC. Son fonctionnement est soumis aux

protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement

l’utilisateur est invité à suivre une ou plusieurs des mesures suivantes pour corriger le problème des

interférences en prenant l’une des mesures suivantes :

É noncé FCC sur l’exposition aux radiations RF

Cet équipement est conforme aux réglementations FCC d’exposition aux radiations définies pour un

environnement non contrôlé. Les utilisateurs doivent respecter les instructions d’exploitation spécifiques

la surface de la tête est de 40.5mm. L’EST étant commercialisé sans casque, il doit donc rester à une

Précautions FCC

Tout changement ou modification non expressément approuvé par la partie chargée de la mise en

conformité peut annuler le droit de l’utilisateur à utiliser l’équipement.

Industry Canada(IC) Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the

following two conditions:

(1)this device may not cause interference, and

(2)this device must accept any interference, including interference that may cause undesired operation of

(2) l’utilisateur de l’appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est

IC RF Exposure Statement

pour satisfaire à la conformité d'exposition RF. L'antenne utilisée pour cet émetteur ne doit pas émettre

simultanément avec d'autres antennes ou émetteurs, sauf en conformité avec les procédures FCC relatives

aux produits multi-émetteurs.

Lorsque équipé, la distance entre l’antenne et la surface de la tête est de 40.5mm.