Sena SP114 Headphone Manuel utilisateur

Sena
Marque
Sena
Modèle
SP114 Headphone
Taper
Manuel utilisateur
Manual
Charging
Red LED: Charging
Blue LED: Fully charged
Power On/Off
Power On : Center Button and Mesh Button for 1 sec
Power Off : Tap the Center Button and Mesh Button
Volume Adjustment
(+) Button - Increase the volume
(-) Button - Decrease the volume
Battery Check
Phone, Music Pairing
Initially Pairing the headset
The headset will automatically enter the phone pairing mode
when you initially turn on the headset or in the following
situation:
• Rebooting after executing Factory Reset
1. Press and hold the Center Button and Mesh Button for 1 second.
2. Search for Bluetooth devices on your mobile phone. Select the ORCA1 in the list of the devices
detected on the mobile phone.
3. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN.
Music Operation
Play or pause music: Press the Center Button for 1 second.
Track back: Press the (-) Button for 1 second.
Track forward: Press the (+) Button for 1 second.
Mobile Phone Call Making and Answering
Answering a call: Tap the Center Button
Ending a call: Press the Center Button for 2 seconds.
Voice dial: Press the Center Button for 3 seconds.
Speed dial: Press the (+) Button for 3 seconds.
Rejecting a call: Press the Center Button for 2 seconds.
Mesh Intercom On/Off
Mesh Intercom On : Tap the Mesh Button.
Mesh Intercom Off : Tap the Mesh Button.
Setting
Configuration Menu: Press the Center Button for 10 seconds.
Troubleshooting
Factory Reset
If you want to restore the headset to factory default settings, use the Factory Reset in the configuration
menu. The headset automatically restores the default settings and turns off.
Certification and Safety Approvals FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment on and off, the user is encouraged to try to correct the interference by
one or more of the following measures:
-Reorient or relocate the receiving antennae
-Increase the separation between the equipment and the receiver
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End
users must follow the specific operating instructions for satisfying RF exposure compliance. The antenna
used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in
accordance with FCC multi-transmitter product procedures.
When equipped, the distance between antenna and one’s head surface is 15.2mm.
FCC Caution
Any changes or modifications to the equipment not expressly approved by the party responsible for
compliance could void user’s authority to operate the equipment.
Industry Canada(IC) Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1)this device may not cause interference, and
(2)this device must accept any interference, including interference that may cause undesired operation of
the device.
Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de
licence. L’exploitation est autorisee aux deux conditions suivantes :
(1) l’appareil ne doit pas produire de brouillage, et
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est
susceptible d’en compromettre le fonctionnement.
IC RF Exposure Statement
Cet équipement est conforme aux limites d'exposition aux radiations de la FCC définies pour un
environnement non contrôlé. Les utilisateurs finaux doivent suivre les instructions d'utilisation spécifiques
pour satisfaire à la conformité d'exposition RF. L'antenne utilisée pour cet émetteur ne doit pas émettre
simultanément avec d'autres antennes ou émetteurs, sauf en conformité avec les procédures FCC relatives
aux produits multi-émetteurs.
Lorsque équipé, la distance entre l’antenne et la surface de la tête est de 15.2mm
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Sena SP114 Headphone Manuel utilisateur

Sena
Marque
Sena
Modèle
SP114 Headphone
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents