Sony MDS-PC2 Manuel utilisateur

3-866-796-12(1)

MiniDisc Deck

Operating Instructions

Mode d’emploi

 1999 Sony Corporation

GB

FR

MDS-PC2

2

GB

WARNING

To prevent fire or shock

hazard, do not expose the

unit to rain or moisture.

Do not install the appliance in a confined

space, such as a bookcase or built-in

cabinet.

This appliance is classified as a CLASS 1

LASER product.

The CLASS 1 LASER PRODUCT

MARKING is located on the bottom

exterior.

The following caution label is located

inside the unit.

IN NO EVENT SHALL SELLER BE

LIABLE FOR ANY DIRECT,

INCIDENTAL OR CONSEQUENTIAL

DAMAGES OF ANY NATURE, OR

LOSSES OR EXPENSES RESULTING

FROM ANY DEFECTIVE PRODUCT OR

THE USE OF ANY PRODUCT.

For the customers in the U.S.A.

This symbol is intended to alert the user to

the presence of uninsulated “dangerous

voltage” within the product’s enclosure

that may be of sufficient magnitude to

constitute a risk of electric shock to

persons.

This symbol is intended to alert the user to

the presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

Declaration of Conformity

Trade name: SONY

Model No.: CAV-50C

Responsible Party: Sony Electronics Inc.

Address: 1 Sony Drive, Park

Ridge, NJ. 07656 USA

Telephone No.: 201-930-6970

This device complies with Part 15 of the

FCC Rules. Operation is subject to the

following two conditions: (1) This device

may not cause harmful interference, and

(2) this device must accept any interference

received, including interference that may

cause undesired operation.

INFORMATION

This equipment has been tested and found

to comply with the limits for a Class B

digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to

provide reasonable protection against

harmful interference in a residential

installation. This equipment generates,

uses, and can radiate radio frequency

energy and, if not installed and used in

accordance with the instructions, may

cause harmful interference to radio

communications. However, there is no

guarantee that interference will not occur

in a particular installation. If this

equipment does cause harmful

interference to radio or television

reception, which can be determined by

turning the equipment off and on, the user

is encouraged to try to correct the

interference by one or more of the

following measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on

a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

CAUTION

You are cautioned that any changes or

modification not expressly approved in

this manual could void your authority to

operate this equipment.

Owner’s Record

The model and serial numbers are located

on the bottom of the unit. Record the

serial number in the space provided below.

Refer to them whenever you call upon

your Sony dealer regarding this product.

Model No. MDS-PC2

Serial No.

For the customers in Canada

CAUTION

TO PREVENT ELECTRIC SHOCK, DO

NOT USE THIS POLARIZED AC PLUG

WITH AN EXTENSION CORD,

RECEPTACLE OR OTHER OUTLET

UNLESS THE BLADES CAN BE FULLY

INSERTED TO PREVENT BLADE

EXPOSURE.

Welcome!

Thank you for purchasing the Sony

MiniDisc Deck. Before operating the

deck, please read this manual

thoroughly and retain it for future

reference.

About This

Manual

The instructions in this manual are for

the MDS-PC2 MiniDisc Deck.

Conventions

• Controls in these instructions are

those on the supplied remote; these

may, however, be substituted by

controls on the deck that are

similarly named, or, when different,

appear in the instructions within

parentheses.

Example: Press H (or NX on the

deck).

• z indicates hints and tips for

making the task easier.

3

GB

TABLE OF CONTENTS

Getting Started 4

Before You Start the Hookup 4

Hooking Up the Audio Components 5

Location and Function of Parts 8

Remote Parts Description 8

Front Panel Parts Description 10

Using the Display 11

Recording on MDs 13

Notes on Recording 13

Recording on an MD 14

Adjusting the Recording Level 16

Recording Tips 16

Marking Track Numbers While Recording

(Track Marking) 18

Starting Recording With Six Seconds of Prestored

Audio Data (Time Machine Recording) 19

Synchro-recording With the Audio Component of

Your Choice (Music Synchro-recording) 19

Synchro-recording With a Sony CD Player

(CD Synchro-recording) 20

Playing MDs 22

Playing an MD 22

Playing a Specific Track 23

Locating a Particular Point in a Track 24

Playing Tracks Repeatedly 25

Playing Tracks in Random Order (Shuffle Play) 26

Creating Your Own Program (Program Play) 26

Tips for Recording From MDs to Tape 28

Editing Recorded MDs 29

Erasing Tracks 30

Dividing Tracks 32

Combining Tracks 33

Moving Tracks 33

Naming Tracks or MDs 34

Undoing the Last Edit 37

Other Functions 38

Fade In and Fade Out Recording 38

Falling Asleep to Music (Sleep Timer) 39

About the CONTROL A1 Control System 39

Additional Information 42

Precautions 42

Handling MDs 43

System Limitations 43

Troubleshooting 44

Specifications 44

Display Messages 45

Edit Menu Table 46

Setup Menu Table 47

Self-Diagnosis Function 47

Index 48

4

GB

Before You Start the

Hookup

Checking the supplied accessories

This MD deck comes with the following items:

• Audio connecting cords

(pin-plug × 2 y pin-plug × 2) (2)

• Optical cable (1)

• Remote commander (remote) RM-D35M (1)

• R6 (size-AA) batteries (2)

• Connector (RS-232C y monaural mini-jack)

* (1)

• Monaural (2P) mini-plug cord

* (1)

• Audio connecting cord

*

(pin-plug × 2 y stereo mini-plug) (2)

• CD-ROM

* (1)

*

Required for operation by personal computer. For details, refer to the

operating instructions supplied with the MD Editor 2 software.

Inserting batteries into the remote

Insert two R6 (size-AA) batteries with the + and –

properly oriented to the markings into the battery

compartment. When using the remote, point it at the

remote sensor

on the deck.

z

When to replace the batteries

Under normal conditions, the batteries should last for about six

months. When the remote no longer operates the deck, replace

both batteries with new ones.

Notes

• Do not leave the remote in an extremely hot or humid place.

• Do not drop any foreign object into the remote casing,

particularly when replacing the batteries.

• Do not use a new battery with an old one.

• Do not expose the remote sensor to direct sunlight or lighting

apparatus. Doing so may cause a malfunction.

• If you don’t use the remote for an extended period of time,

remove the batteries to avoid possible damage from battery

leakage and corrosion.

Getting

Started

This chapter provides information on

the supplied accessories, things you

should keep in mind while hooking

up the system, and how to connect

various audio components to the MD

deck. Be sure to read this chapter

thoroughly before you actually

connect anything to the deck.

5

GB

Getting Started

Hooking Up the Audio Components

DIGITAL

(OPTICAL)

OUT IN

MD

IN

L

R

OUT

DIGITAL

(OPTICAL)

OUT

DIGITAL CONTROL

A1

(VARIABLE)

IN1 OUTIN2

LINE (ANALOG)

OUT (OPTICAL)

L

R

IN

Required cords

Audio connecting cords (2) (supplied)

When connecting an audio connecting cord, be sure to match the

color-coded pins to the appropriate jacks: white (left) to white

and red (right) to red.

Optical cable (2) (only one supplied)

• When connecting an optical cable, take the caps off the

connectors and insert the cable plugs straight in until they click

into place.

• Do not bend or tie the optical cable.

White (L) White (L)

Red (R) Red (R)

Things you should keep in mind while

hooking up the system

• Turn off the power to all components before making

any connections.

• Do not connect any AC power cord until all the

connections are completed.

• Be sure the connections are firm to prevent hum and

noise.

Jacks (connectors) for connecting audio

components

Connect To the

Amplifiers LINE (ANALOG) IN/OUT jacks

Digital amplifiers DIGITAL (OPTICAL) IN2/OUT

connectors

Amplifier, etc. Digital amplifier, etc.

AC power cord

DAT decks, another MD deck,

CD players, or DBS tuners

DIGITAL (OPTICAL) IN1

connector

DAT deck, MD deck, CD player,

DBS tuner, etc.

6

GB

Getting Started

Connecting audio conponents to CONTROL

A1 jacks

Monaural (2P) mini-plug cords (not supplied)

For information on connections through the CONTROL

A1 jacks, see page 39.

Connecting the AC power cord

Connect the AC power cord of the deck to a wall outlet.

Note

Do not connect the AC power cord to a switched outlet.

Connecting a personal computer

Connect the MD deck to a personal computer using a

monaural mini-plug cord (2-pin) (supplied) and a

connector (supplied).

By this connection, you can edit MDs on computer’s

display or input disc names and track names using

computer’s keyboard. For connection and operation, refer

to the operating instructions supplied with the MD editor

2 software for details.

Notes on setting up

• Don’t place your personal computer on top of this

MD deck.

• Don’t install the deck vertically (sideways).

Hooking Up the Audio Components

7

GB

Getting Started

8

GB

Remote Parts Description

1

2

3

4

6

9

0

qs

7

wd

ws

qa

wa

qh

ql

qk

qj

qd

qf

qg

w;

5

8

ABC

REC LEVEL

CD-SYNC

MUSIC

SYNC

A

y

B

REPEAT

2

DEF

3

& ! ?

REC FADERSCROLLDISPLAY

EJECT

PLAY MODE

NAME IN

CLEARYES

MENU/NO

CHARNAME

STANDBY

STOP

START

INPUT

1

JKL

5

MNO

6

GHI

4

TUV

8

QZ

10/0

T.REC

>

10

WXY

9

PRS

7

ANALOG

OUT LEVEL

. >

m M

z x

X

H

Z

` / 1

+

–

Location and

Function of

Parts

This chapter tells you about the

location and function of the various

buttons and controls on the supplied

remote and the front panel. Further

details are provided on the pages

indicated in the parentheses.

It also tells you about the information

that appears in the display window.

9

GB

Location of Parts and Brief Explanations

1 ?/1 (power) switch (14, 22)

Press to turn the deck on. When you turn the deck on,

the ?/1 switch indicator on the deck turns off. When

you press the switch again, the deck turns off and the

indicator lights up red.

2 CLEAR button (27, 35)

Press to cancel the selection.

3 REC FADER button (38)

Press to perform Fade-in Recording or Fade-out

Recording.

4 PLAY MODE button (26)

Press to select Shuffle Play or Program Play.

5 Letter/number buttons (24, 34)

Press to enter a track number directly or input letters

or numbers.

6 MUSIC SYNC button (19)

Press to start Music Synchro-recording.

7 CD-SYNC STOP button (20)

Press to stop CD Synchro-recording.

CD-SYNC START button (20)

Press to start CD Synchro-recording.

CD-SYNC STANDBY button (20)

Press to enter standby for CD Synchro-recording.

8 ANALOG OUT LEVEL +/– buttons (23)

Press to adjust the output level from the LINE

(ANALOG) OUT jacks and PHONES jack.

9 X button (15, 22)

Press to pause play or recording. Press again to

resume play or recording.

q; x button (15, 22, 30)

Press to stop play, stop recording, or cancel the

selected operation.

qa REC LEVEL +/– buttons (16)

Press to adjust the recording level.

qs AyB button (25)

Press to select Repeat A-B Play.

qd REPEAT button (25)

Press to play tracks repeatedly.

qf m/M buttons (24, 26, 31, 35)

Press to locate a portion within a track, change the

contents of a program, or shift the cursor.

qg ./> buttons (14, 22, 26, 30, 39)

Press to locate tracks or select a menu item.

qh z button (15, 17, 18)

Press to record on the MD, monitor the input signal, or

mark track numbers.

qj T.REC button (19)

Press during recording pause to start Time Machine

Recording.

qk H button (15, 22)

Press to start play.

ql INPUT button (14)

Press to select the input jack (or connector) of the

program source to be recorded.

w; NAME button (34)

Press to add the name or change the name of a track or

MD.

CHAR button (34)

Press to select the type of characters to be input when

naming a track or MD.

wa DISPLAY button (11, 16, 26)

Press to select the information to be displayed in the

window.

SCROLL button (12)

Press to scroll the name of a track or MD.

ws MENU/NO button (14, 26, 30, 39)

Press to display “Edit Menu” or “Setup Menu.”

YES button (14, 26, 30, 39)

Press to carry out the selected operation.

wd EJECT Z button (15, 22)

Press to eject the MD.

10

GB

Location of Parts and Basic Amplifier Operations

Front Panel Parts Description

1 32 54

q;

6

9qa

8 7

Z? /1

z

NX

.>

x

INPUT

PHONES

1 ?/1 (power) switch (14, 22)

Press to turn the deck on. When you turn the deck on,

the switch indicator turns off. When you press the

switch again, the deck turns off and the indicator

lights up red.

2 Remote sensor (4)

Point the remote towards this window (

) for

remote operations.

3 MD insertion slot (14, 22)

Insert the MD as illustrated below.

With the labeled side up

Z

? /

1

z

N

X

.

>

x

With the arrow pointing towards the deck

4 NX button (15, 22)

Press to start play, pause play, or pause recording.

5 Z button (15, 22)

Press to eject the MD.

6 z button (15, 17, 18)

Press to record on the MD, monitor the input signal, or

mark track numbers.

7 x button (15, 22, 30)

Press to stop play, stop recording, or cancel the

selected operation.

8 ./> buttons (14, 22, 24, 26, 30, 39)

Press to locate tracks or a portion within a track.

9 Display window (11, 12)

Shows various information.

0 PHONES jack (23)

Connect the headphones. Press ANALOG OUT

LEVEL +/– on the remote to adjust the volume.

qa INPUT button (14)

Press to select the input jack (or connector) of the

program source to be recorded.

11

GB

Location of Parts and Brief Explanations

Using the Display

The display window shows information about the MD or

track. This section describes the information that appears

for each deck status.

SCROLL

DISPLAY

. >

m M

z x

X

H

Z

` / 1

+

–

+

–

Note

The type of information (e.g., total number of tracks, recorded

time, remaining time, track or disc name) which was last

displayed will continue to appear until you change it by pressing

DISPLAY, even if you change the deck operation status. For

example, if the remaining time was displayed when you stop the

deck, the remaining time will continue to appear when you begin

playing the same MD again or a different one.

When you insert an MD

The display automatically changes as follows:

15 46m 08s

SONGS

While the deck is stopped

Press DISPLAY repeatedly to change the display.

Each press of the button changes the display as follows:

15 46m 08s

-27m 52s

SONGS

*

Not shown for the premastered discs.

**

When the MD has no name, “No Name” appears, followed by the

default display.

While the deck is recording

Press DISPLAY repeatedly to change the display.

Each press of the button changes the display as follows:

16 3m 05s

-24m 47s

BALLAD

*

When the track has no name, “No Name” appears, followed by the

default display.

Total number of tracks Total recorded time

Disc name

Total number of tracks and total

recorded time (default display)

Press

Remaining recordable time on the

MD (recordable MDs only)*

Press

Disc name**

Press

Track number and recorded time of

the current track (default display)

Press

Remaining recordable time on the

MD

Press

Level of the input signal

Press

Track name*

Press

12

GB

Location of Parts and Basic Amplifier Operations

While the deck is playing

Press DISPLAY repeatedly to change the display.

Each press of the button changes the display as follows:

2 3m 33s

2 -1m 25s

DIARY

*

When the track has no name, “No Name” appears, followed by the

default display.

z

You can check the track name at any time while playing

Press SCROLL.

The track name appears and scrolls. While the track name is

scrolling, press the button again to pause scrolling, and again to

continue scrolling.

Using the Display

Track number and elapsed time of

the current track (default display)

Press

Track number and remaining time of

the current track

Press

Track name*

Press

13

GB

Recording on MDs

Recording on

MDs

This chapter explains the various

ways to record on an MD, as well as

how to mark track numbers and

perform synchro-recording with other

components.

Notes on Recording

About indications which appear while

recording

When “Protected” and “C11” alternate in the

display

The record-protect slot is open and the MD is record-

protected. To record on the MD, slide the tab to close the

slot. For details, see “To prevent accidental erasure of the

recorded material” on page 15.

When “Din Unlock” and “C71” alternate in the

display

• The digital component selected with the INPUT button

is not connected correctly. Check the connection.

• The selected digital component is not turned on. Turn

on the component.

When “Cannot Copy” appears in the display

The MD deck uses the Serial Copy Management System.

MDs recorded through the digital input connector can’t be

copied to other MDs or DAT tapes through the digital

output connector. For details, see “Guide to the Serial

Copy Management System” on page 14.

When “TRACK” flashes in the display

The MD deck is recording over existing track(s)

(“Recording on an MD” on page 14). The indication stops

flashing when the deck reaches the end of the recorded

portion.

About indications which appear after

recording

When “TOC” lights up in the display

Recording has finished but the TOC (Table of Contents)

on the MD has not been updated to reflect the recording

results. The recording will be lost if you disconnect the

AC power cord while the indication is on. The TOC will

be updated only when you eject the MD or turn off the

MD deck.

When “TOC Writing” flashes in the display

The deck is updating the TOC. Do not disconnect the AC

power cord or move the deck while the indication flashes.

14

GB

Recording on MDs

Automatic conversion of digital sampling

rates during recording

A built-in sampling rate converter automatically converts

the sampling frequency of various digital sources to the

44.1 kHz sampling rate of the MD deck. This allows you

to monitor and record sources such as 32- or 48-kHz DAT

tapes or satellite broadcasts, as well as the CDs and MDs.

Please note that 22.05- or 96-kHz digital sources can’t be

recorded on this deck.

Guide to the Serial Copy Management

System

Digital audio components, such as CDs, MDs, and DATs

make it easy to produce high-quality copies of music by

processing music as a digital signal.

To protect copyrighted music sources, this deck uses the

Serial Copy Management System which allows you to

make only a single copy of a digitally recorded source

through digital-to-digital connections.

You can make only a first-generation copy

*

through a digital-to-digital connection.

Examples are given as follows:

• You can make a copy of a commercially available digital

sound program (for example, a CD or MD), but you

can’t make a second copy from the first-generation

copy.

• You can make a copy of a digital signal from a digitally

recorded analog sound program (for example, an

analog record or a music cassette tape) or from a digital

satellite broadcast program, but you can’t make a

second copy from the first-generation copy.

*

A first-generation copy means the first recording of a digital audio

source through the deck’s digital input connector. For example, if you

record from a CD player connected to the DIGITAL (OPTICAL) IN1

connector, that copy is a first-generation copy.

Note

The restrictions of the Serial Copy Management System don’t

apply when you make a recording through the analog-to-analog

connections.

Recording on an MD

The operations for normal recording are explained below.

If the MD has recorded material on it, the deck will

automatically start recording from the end of the recorded

portion.

H

MENU/NO

INPUT

YES

./>

z

EJECT Z

X

x

?/1

. >

m M

z x

X

H

Z

` / 1

+

–

+

–

1 Turn on the amplifier and program source, and

select the source on the amplifier.

2 Press ?/1 to turn on the deck.

The switch indicator on the deck turns off.

3 Insert a recordable MD.

4 Press INPUT repeatedly to select the input jacks

(connectors) connected to the program source.

If the source is connected to the Select

DIGITAL (OPTICAL) IN1 connector Optical 1 In

DIGITAL (OPTICAL) IN2 connector Optical 2 In

LINE (ANALOG) IN jacks Analog In

5 Press MENU/NO twice.

“Setup Menu” appears in the display.

6 Press ./> repeatedly until “Stereo Rec” or

“Mono Rec” appears in the display, then press YES.

7 Press ./> repeatedly to select the recording

mode, then press YES.

To record in Select

Stereo Stereo Rec (factory setting)

Monaural Mono Rec

Monaural mode allows you to record about twice as

much material as stereo.

Notes on Recording

15

GB

Recording on MDs

8 Press MENU/NO.

9 If necessary, locate the point on the MD to start

recording from.

If you want to record on a new MD or start recording

from the end of the recorded portion, go to step 10.

To record over from the beginning of an existing MD

track

Press ./> repeatedly until the number of the

track to be recorded over appears.

To record over from the middle of an MD track

Press ./> repeatedly until the number of the

track to be recorded over appears, then press H (or

NX on the deck) to start playback. Press X (or NX

on the deck) at the point you want to start recording

from.

10Press z.

The deck changes to recording pause.

11If you have selected “Analog In” in step 4 above,

adjust the recording level.

For details, see “Adjusting the Recording Level” on

page 16.

12Press H or X (or NX on the deck).

Recording starts.

13Start playing the program source.

Operations you may want to do during recording

To Press

Stop recording x

Pause recording X (or NX on the deck)

Resume recording after pausing H or X (or NX on the deck)

Eject the MD EJECT Z after stopping

recording

When you pause recording

The track number increases by one. For example, if you

paused recording while recording track 4, the track

number will be 5 when you resume recording.

Bottom side of the MD

To prevent accidental erasure of the recorded

material

To make it impossible to record on an MD, slide the

record-protect tab in the direction of the arrow (see

illustration below) to open the slot. To enable recording,

close the slot.

z

To play the tracks you just recorded

Press H (or NX on the deck) immediately after stopping

recording.

The deck starts to play from the first track of the material just

recorded.

z

To play from the first track of the MD after recording

1 Press x again after stopping recording.

2 Press H (or NX on the deck).

The deck starts to play from the first track of the MD.

Note

• You can’t record over existing material when Shuffle Play (page

26) or Program Play (page 26) has been selected. “Impossible”

appears in the display at this time.

• You can’t use the buttons on the remote or the deck while the

deck is controlled by a personal computer. “REMOTE” appears

in the display at this time.

Slide in the

direction of arrow

Record-protect tab

16

GB

Recording on MDs

Adjusting the Recording

Level

Do the procedure below to adjust the recording level.

DISPLAY

REC LEVEL +/–

. >

m M

z x

X

H

Z

` / 1

+

–

+

–

1 Do steps 1 to 10 of “Recording on an MD” on pages

14 and 15.

2 Play the portion of the program source with the

strongest output.

3 Press DISPLAY repeatedly until the peak level

meters appear.

4 While monitoring the sound, press REC LEVEL +/–

repeatedly to adjust the recording level to its

highest level without turning on “OVER” on the

peak level meters.

Occasional lighting of “OVER” is acceptable.

Avoid turning this indication on.

5 Stop playing the program source.

6 To start recording, continue from step 12 of

“Recording on an MD” on page 15.

z

You can adjust the recording level during recording

Press REC LEVEL +/– repeatedly.

z

To display the level of the strongest signal

The Peak Hold function continuously displays the level of the

strongest signal that has been input.

Do the procedure below to turn Peak Hold on.

1 While the deck is stopped, press MENU/NO twice to display

“Setup Menu.”

2 Press ./> repeatedly until “P.Hold” appears, then press

YES.

3 Press ./> repeatedly to select “P.Hold On,” then press

YES.

4 Press MENU/NO.

To turn Peak Hold off, repeat the procedure above, selecting

“P.Hold Off” in step 3.

Recording Tips

MENU/NO

INPUT

YES

./>

z

DISPLAY

EJECT Z

. >

m M

z x

X

H

Z

` / 1

+

–

+

–

Checking the remaining recordable time

on the MD

Press DISPLAY repeatedly.

While the deck is The following information appears

Stopped Total number of tracks and total recorded

time t Remaining recordable time on

the MD t Disc name

Recording Recorded time of the current track t

Remaining recordable time on the MD t

Input level indication t Track name

For details, see page 11.

Monitoring the input signal

(Input Monitor)

You can monitor the selected input signal even when

you’re not recording it.

1 Press EJECT Z to eject the MD.

2 Press INPUT repeatedly to select the jacks

(connectors) which the signal you want to monitor

is being input.

17

GB

Recording on MDs

Erasing blank portions automatically

(Smart Space/Auto Cut)

The deck can be set to automatically erase any blanks that

are produced when the signal is interrupted during

recording. The function which activates (Smart Space or

Auto Cut) depends on the length of the interruption, as

described below.

Smart Space

If the signal is interrupted for less than 30 seconds, Smart

Space replaces the blank portion with a blank space of

about three seconds, then continues the recording. “Smart

Space” appears in the display during this time.

Auto Cut

If the signal is interrupted for about 30 seconds, Auto Cut

replaces the blank portion with a blank space of about

three seconds, then pauses the recording. “Auto Cut”

appears in the display during this time.

Do the procedure below to turn Smart Space and Auto

Cut on or off.

1 While the deck is stopped, press MENU/NO twice.

“Setup Menu” appears in the display.

2 Press ./> repeatedly until “S.Space” appears,

then press YES.

3 Press ./> repeatedly to select the setting,

then press YES.

To Select

Turn on Smart Space and Auto Cut S.Space On (factory

setting)

Turn off Smart Space and Auto Cut S.Space Off

4 Press MENU/NO.

Notes

• If you start recording with no signal input, Smart Space and

Auto Cut will not operate regardless of the setting.

• Smart Space does not affect the order of the track numbers

being recorded, even if the blank space occurs in the middle of

a track.

• Auto Cut is automatically turned on or off in tandem with

Smart Space.

• If you turn off the deck or disconnect the AC power cord, the

deck will store the last setting (“S.Space On” or “S.Space Off”)

and apply it the next time you turn on the deck.

3 Press z.

When “Analog In” is selected

The analog signal input from the LINE (ANALOG) IN

jacks is output to the DIGITAL (OPTICAL) OUT

connector after A/D conversion, and then to the LINE

(ANALOG) OUT jacks after D/A conversion. “AD -

DA” appears in the display at this time.

When “Optical 1 In” or “Optical 2 In” is selected

The digital signal input from the DIGITAL (OPTICAL)

IN1 or IN2 connector first passes through the

sampling rate converter, and then output to the

DIGITAL (OPTICAL) OUT connector, and then to the

LINE (ANALOG) OUT jacks after D/A conversion. “-

DA” appears in the display at this time.

To stop monitoring the signal

Press x.

18

GB

Recording on MDs

4 Press MENU/NO.

The deck marks a track number whenever the input

signal level drops to –50 dB (the trigger level for

Automatic Track Marking) or below for at least 1.5

seconds.

To change the trigger level for Automatic Track

Marking

Do the procedure below to change the signal level that

triggers Automatic Track Marking.

1 While the deck is stopped, press MENU/NO twice.

“Setup Menu” appears in the display.

2 Press ./> repeatedly until “LS(T)” appears,

then press YES.

3 Press ./> repeatedly to select the level, then

press YES.

You can set the level at any value between –72 dB and

0 dB, in 2 dB steps.

4 Press MENU/NO.

z

Additional information on Automatic Track Marking

• When recording from a CD player or MD deck connected to the

DIGITAL (OPTICAL) IN1/2 connector, the entire material may

be recorded as a single track in the following cases:

— When you consecutively record the same track two or more

times using single-track repeat play.

— When you consecutively record two or more tracks with the

same track number but from different CDs or MDs.

— When you record tracks from certain CD or multi-disc

players.

Also, if the source is an MD, a track number may not be

marked for tracks less than four seconds long.

• When recording from a component connected to the LINE

(ANALOG) IN jacks with “T.Mark Off” selected or when

recording from a DAT deck or DBS tuner connected to the

DIGITAL (OPTICAL) IN1/2 connector, the entire material may

be recorded as a single track.

• When recording from a DAT deck or DBS tuner connected to

the DIGITAL (OPTICAL) IN1/2 connector, the deck will mark a

track number whenever the sampling frequency of the input

signal changes, regardless of the track marking parameter

setting (“T.Mark LSync” or “ T.Mark Off”).

z

You can mark track numbers even after recording has

finished

See “Dividing Tracks” on page 32.

Note

If you turn off the deck or disconnect the AC power cord, the

deck will store the last settings (“T.Mark LSync” or “ T.Mark Off”

and the trigger level) and apply them the next time you turn on

the deck.

Marking Track Numbers

While Recording (Track Marking)

You can mark track numbers either manually or

automatically while recording. By marking track

numbers at specific points, you can quickly locate the

points later or edit the MD easily.

MENU/NO

YES

./>

z

. >

m M

z x

X

H

Z

` / 1

+

–

+

–

Marking track numbers manually

(Manual Track Marking)

Press z at the point where you want to add a track

number while recording.

Marking track numbers automatically

(Automatic Track Marking)

When recording from a CD player or MD deck connected

to the DIGITAL (OPTICAL) IN1/2 connector, the deck

marks track numbers in the same sequence as the source.

When recording from other sources connected to the

DIGITAL (OPTICAL) IN1/2 connector or a source

connected to the LINE (ANALOG) IN jacks, do the

procedure below to mark track numbers automatically.

1 While the deck is stopped, press MENU/NO twice.

“Setup Menu” appears in the display.

2 Press ./> repeatedly until “T.Mark” appears,

then press YES.

3 Press ./> repeatedly to select the setting,

then press YES.

To Select

Turn on Automatic Track Marking T.Mark LSync (factory

setting)

Turn off Automatic Track Marking T.Mark Off

19

GB

Recording on MDs

Synchro-recording With the

Audio Component of Your

Choice (Music Synchro-recording)

The Music Synchro-recording allows you to automatically

synchronize recording on the MD deck with the playing

of the selected program source. The Track Marking

function, however, will differ according to the program

source. For details, see “Marking Track Numbers While

Recording” on page 18.

MUSIC SYNC

. >

m M

z x

X

H

Z

` / 1

+

–

+

–

1 Do steps 1 to 9 of “Recording on an MD” on pages

14 and 15.

2 Press MUSIC SYNC.

The deck changes to recording pause.

3 Start playing the program source.

Recording starts automatically.

To stop Music Synchro-recording

Press x.

Note

During Music Synchro-recording, Smart Space and Auto Cut will

operate regardless of their setting (“S.Space On” or “S.Space

Off”).

Starting Recording With Six

Seconds of Prestored Audio

Data (Time Machine Recording)

Whenever the deck is in recording pause, the deck’s

buffer memory continuously stores the latest six seconds

worth of audio data. When you press T.REC, the

recording then starts with the data in the buffer memory.

Time Machine Recording thus allows you to avoid

missing the beginning of material recorded live from an

FM or satellite broadcast.

T.REC

. >

m M

z x

X

H

Z

` / 1

+

–

+

–

1 Do steps 1 to 10 of “Recording on an MD” on pages

14 and 15.

The deck changes to recording pause.

2 Start playing the program source.

3 Press T.REC at the point where you want to start

recording.

Recording starts with the six seconds of prestored data

in the buffer memory, then continues recording via the

buffer memory thereafter.

To stop Time Machine Recording

Press x.

Note

The storage of data in the buffer memory starts from the moment

the deck changes to recording pause. Thus, if you start recording

less than six seconds after changing to recording pause, less than

six seconds worth of data will be recorded from the buffer

memory. The same is true if the program source had been

playing for less than six seconds at the time you start recording.

20

GB

Recording on MDs

Operations you may want to do during CD

Synchro-recording

To Press

Stop recording CD-SYNC STOP

Pause recording CD-SYNC STANDBY

Resume recording after

pausing

CD-SYNC START

Check the remaining

recordable time on the MD

DISPLAY (page 11)

z

You can use the remote of the CD player during CD Synchro-

recording

Press To change the deck to And change the CD player to

H Recording Play

x Recording pause Stop

X Recording pause Pause

z

You can select the next track to be recorded using the

remote of the CD player during recording pause

1 Press X to pause recording.

2 Press ./> repeatedly to select a track.

3 Press H to resume recording.

z

During CD Synchro-recording, track numbers are marked in

the following ways:

• When the CD player is connected to the DIGITAL (OPTICAL)

IN1/2 connector, track numbers are automatically marked as

they appear on the CD.

• When the CD player is connected to the LINE (ANALOG) IN

jacks, track numbers are automatically marked when “T.Mark

LSync” has been selected (page 18).

• When you resume recording after recording pause, a new track

number is automatically marked, regardless of the track

marking parameter setting (“T.Mark LSync” or “ T.Mark Off”).

z

You can change CDs during CD Synchro-recording

1 Press x on the CD player’s remote.

2 Change the CD.

3 Press H on the CD player’s remote to resume recording.

Synchro-recording With a

Sony CD Player

(CD Synchro-recording)

When the deck is connected to a Sony CD player or Hi-Fi

component system, you can easily copy the contents of

CDs to the MD using the deck’s remote. As the same

remote operates both the MD deck and the CD player or

CD player section of the component system, make sure to

place the MD deck and the CD player as close together as

possible.

Note

On some CD players and Hi-Fi component systems, you may

find it impossible to perform CD Synchro-recording using the

deck’s remote. In this case, use Music Synchro-recording (page

19) to record from CDs to the MD.

CD-SYNC STANDBY

CD-SYNC START

CD-SYNC STOP

DISPLAY

. >

m M

z x

X

H

Z

` / 1

+

–

+

–

1 Turn on the amplifier and the CD player, and select

CD on the amplifier.

2 Do steps 2 to 9 of “Recording on an MD” on pages

14 and 15.

3 Insert a CD into the CD player and select the

playback mode (shuffle play, program play, etc.) on

the CD player.

4 Press CD-SYNC STANDBY.

The CD player changes to play standby and the MD

deck changes to recording standby.

5 Press CD-SYNC START.

The deck starts recording and the CD player starts to

play.

The track number and elapsed recording time of the

track appear in the display.

If the CD player doesn’t start playing

Some CD players may not respond when you press

CD-SYNC START. Press X on the CD player’s remote

to start play on the CD player.

La page est en cours de chargement...

Sony MDS-PC2 Manuel utilisateur

Sony MDS-PC2 Manuel utilisateur

dans d''autres langues

Documents connexes