Silvercrest 289484 Operation and Safety Notes

Taper
Operation and Safety Notes
CHARGING AND
DATA CABLE
IAN 289484
LADE- UND DATENKABEL
Bedienungs- und Sicherheitshinweise
CHARGING AND DATA CABLE
Operation and Safety Notes
LADE- OG DATAKABEL
Brugs- og sikkerhedsanvisninger
CÂBLE DE CHARGE ET
SYNCHRONISATION
Instructions d‘utilisation et consignes de sécurité
LAAD- EN DATAKABEL
Bedienings- en veiligheidsinstructies
CHARGING AND
DATA CABLE
GB / IE / NI Operation and Safety Notes Page 5
DK Brugs- og
sikkerhedsanvisninger Side 26
FR / BE Instructions d‘utilisation et
consignes de sécurité Page 47
NL / BE Bedienings- en
veiligheidsinstructies Pagina 71
DE / AT / CH Bedienungs- und
Sicherheitshinweise Seite 94
3
1
2
4
5
6
7
5 GB/IE/NI
List of pictograms
used and warnings ................Page 6
Introduction .................................Page 6
Intended use ...................................Page 7
Warnings and symbols used .........Page 7
Trademark notice ........................... Page 9
Scope of delivery ........................... Page 9
Before use.......................................Page 9
Parts description ............................. Page 10
Technical data ................................Page 10
Safety notices.............................Page 11
Operation and use .................Page 15
Charging the power bank ............. Page 15
Checking the battery status ........... Page 17
Charging mobile devices with
the power bank ..............................Page 18
Data transfer ..................................Page 19
Usage as a charging cable ...........Page 19
Troubleshooting ....................... Page 19
Cleaning and care ................... Page 21
Storage during non-use ......Page 22
Disposal .........................................Page 22
Note to Declaration of
conformity .................................... Page 24
Warranty ......................................Page 24
6 GB/IE/NI
List of pictograms
used and warnings
Read the instructions!
Direct current
Observe caution and
safety notes!
Caution!
Explosion hazard
Wear suitable
protective gloves
Charging and Data Cable
Introduction
We congratulate you on the purchase
of your new product. You have chosen
a high quality product. The instruc-
tions for use are part of the product.
They contain important information
concerning safety, use and disposal.
Before using the product, please
familiarise yourself with all of the
safety information and instructions
7 GB/IE/NI
for use. Only use the product as de-
scribed and for the specified appli-
cations. If you pass the product on
to anyone else, please ensure that
you also pass on all the documenta-
tion with it.
Intended use
This product is an IT device which is
solely intended to be used to charge
mobile devices which are normally
charged through a USB port. This
product is not intended for commer-
cial use. Manufacturer is not liable
for damages, which result from non-
Intended use.
Any claims resulting from improper
use or due to unauthorised modifica-
tion of the product will be consid-
ered un-warranted. Any such use is
at your own risk.
Warnings and
symbols used
These instructions for use contain the
following warnings:
8 GB/IE/NI
DANGER
This symbol in conjunction with the
„danger“ note indicates an immi-
nent dangerous situation which, if
not prevented, could result in serious
injury or even death.
WARNING
This symbol in conjunction with the
„warning“ note indicates important
information for safe operation of the
device and the safety of the user.
CAUTION!
This symbol with the signal
word indicates a hazard with
a low level of risk which, if
not avoided, could result in
minor or moderate injury.
NOTE
This symbol with the signal word
provides additional useful information.
9 GB/IE/NI
Trademark notice
- USB
®
is a registered trademark
of USB Implementers Forum,
Inc.
- The SilverCrest trademark and
trade name is the property of
their respective owners.
- Lightning is a trademark of
Apple Inc.
- Any other names and products
may be trademarks or registered
trademarks of their respective
owners.
Scope of delivery
1 Charging and Data Cable
1 Instructions for use
Before use
Note: All parts have to be un-
packed and the packaging material
has to be removed completely.
Please also check the content of
delivery inside packaging to see
if any damages. If you notice any
damage or missing parts, please
contact the dealer who sold this
product.
10 GB/IE/NI
Parts description
Please refer to fold out page
front / rear.
1
Lightning charging plug
2
Micro-USB plug
3
USB type A plug
4
LED indicator
5
Power- / status button
6
Power bank
7
Instructions for use
Technical data
Built-in battery: 3.7 V / 450 mAh
(Lithium poly-
mer)
Input voltage/
current: 5 V
, max.
500 mA
Output voltage/
current: 5 V
, 1 A
Minimum output
current: approx. 80 m
Operating
temperature: 5°C –35°C
Storage
temperature: 0°C – 45°C
Humidity
(no condensation): 10 % – 70 %
11 GB/IE/NI
Dimension
(Length x Diameter): approx.
103 x 17mm
Weight: approx. 40 g
Cable length: 1 meter
Safety notices
Please familiarise yourself with all in-
structions for use and Safety notices
before using the product for the first
time. When passing this product on
to third parties, please be sure to in-
clude all documentation.
Check the product for visible ex-
ternal damage before use. Do
not use the product if damaged
or dropped.
This product may be used by
children age 8 years and up, as
well as by persons with physical,
sensory or mental impairments
or lacking experience and / or
knowledge, provided they are
supervised or instructed in the
safe use of the product and
12 GB/IE/NI
understand the associated risks.
Do not allow children to play
with the product. Never allow
children to clean or maintain
this product unsupervised.
DANGER! Packaging materi-
als are not a toy. Keep all packag-
ing materials out of the reach of
children. Suffocation hazard!
Do not expose the product to
direct sunlight or high tempera-
tures. It may otherwise overheat
and be damaged beyond repair.
Do not operate the product near
heat sources such as radiators
or other devices producing heat.
Do not operate the product near
open flames, e.g. candles, open
flames.
The product is not designed for
use in rooms with high tempera-
tures or humidity (i.e bathrooms)
or those in which a great amount
of dust is generated.
Do not expose the product to
extremely high temperatures.
This applies in particular if you
are thinking about storing the
13 GB/IE/NI
product in your car. Over a pro-
longed period of time, the car
and the glove compartment
could become extremely hot.
Remove electric and electronic
devices from the car.
Do not use the product immedi-
ately after it has brought from a
cold room to a warm room.
Allow the product to acclimatise
before you switch it on.
DANGER! Never open the
product casing. This product has
no internal parts requiring main-
tenance.
Do not independently convert or
modify the product.
Repairs to the product must be
performed by authorised spe-
cialised companies or customer
service. Improper repairs may
place the user in considerable
danger. They will also void the
warranty.
Do not expose the product to
dripping water or splashing wa-
ter and do not place containers
filled with liquids such as vases
14 GB/IE/NI
or open drinks on top of or
beside the product.
Immediately switch the product
off and remove the charging ca-
ble from the product if you smell
burning or see smoke. Have the
product examined by a quali-
fied technician before using it
again.
If you use a USB power supply,
the socket used must always be
easily accessible so that the
USB power supply can be quickly
removed from the socket in the
case of emergency. Please also
refer to the USB Power supply
manufacturer‘s instruction
manual.
DANGER! Improper han-
dling of lithium polymer batter-
ies can result in fire, explosions,
hazardous substances leaking,
or other dangerous situations!
Do not throw the product into
the fire, as this could lead to the
built-in battery exploding.
Observe the usage restrictions
and prohibitions of use for
15 GB/IE/NI
battery-operated products in sit-
uations which may be hazard-
ous such as at petrol stations,
airports, hospitals, etc.
WARNING! During charg-
ing process, please be noticed
that the product must not be
covered.
Operation and use
Charging the
power bank
The built-in rechargeable battery
must be fully charged before using
the product. The required charging
time for the power bank
6
depends
on the charging source and its out-
put power.
To charge the power bank
6
only use power supplies with an
output voltage of 5 V and an
output current of at least 500 mA.
Connect the one end of this
product
3
(USB Type A) to a
USB power supply (not included
in the scope of delivery).
16 GB/IE/NI
The battery status will be shown
by LED indicator
4
and differ-
ent LED color refer to power
bank battery capacity level dur-
ing the charging process.
To check with the power bank
battery capacity level, press the
power button / status button
5
,
LED indicator
4
will light up to
show the relavant bank power
battery level refer to below table,
LED indicator will automatically
off after 5 seconds.
Table A -
Checking
battery status
battery
power level
indication
LED light
status
57 % - 100 % Blue light up
15 % - 56 % Green light up
6 % - 14 % Red light up
0 % - 5 % Red flashing
17 GB/IE/NI
Table B -
Under
Charging
mode battery
power level
indication
LED light
status
99 % - 100 % Blue light up
66 % - 98 % Green light up
33 % - 65 % Red light up
0 % - 32 % Red flashing
Checking the
battery status
You can check the battery status on
the LED indicator
4
anytime.
Lightly press the Power /
status button
5
. The LED indi-
cator
4
shows the current bat-
tery status of the power bank
6
for approx. 5 seconds in
terms of LED indicator’s color,
details refer to table A.
Note: If battery power level
of the power bank
6
is lower
than 5%, the LED indicator
4
will automatically flash to show
18 GB/IE/NI
power level is low, the product
need to charge up now.
Charging mobile
devices with the
power bank
Connect charging USB cable
2
micro-USB port or Lightning
charging plug
1
to device to
be charged. The charging pro-
cess will start automatically.
In case if the charging process
does not begin immediately,
press the Power / status Button
5
lightly to begin the charging
process. The current battery sta-
tus of the power bank
6
is indi-
cated during the charging
process by the LED indicator
4
,
please refer to Table B for more
details.
To end the charging process,
separate the USB charging ca-
ble Or lightning cable plug
1
from the mobile device and the
power bank
6
. The LED indica-
tor
4
will switch off after ap-
prox. 5 seconds.
19 GB/IE/NI
Data transfer
Use this product as a data cable
to transfer files directly through
your devices to computers or
other devices
Usage as a
charging cable
In this case, higher charging cur-
rent are possible to charge up
tablet computer as well. But it
depends on the tablet computer
charging current and voltage re-
quirements, details please check
with tablet manufacturer user
manual before charging your
tablet to make sure your tablet
device compatible with this
charging cable
Troubleshooting
= Problem
= Cause
= Solution
The power bank
6
is not
being charged.
20 GB/IE/NI
It may be that the power bank is
not connected properly.
Check that it is connected.
A connected device is not
being charged.
The battery is drained.
Charge the battery.
The device is not connected.
Check that it is connected.
Lightly press the power / status
button
5
to begin the charging
process.
The current consumption of the
connected device might be too
low.
Check with your connected de-
vice manual and see if your con-
nected device current
consumption comply with this
product.
The power bank
6
does
not react when the button
is pressed or when a de-
vice is connected, even
though the battery is
charged
21 GB/IE/NI
The power consumption of the
connected devices is too high.
Therefore, the internal overcurrent
protection device was activated.
At the moment, unplug the con-
nected device and power bank
will automatically remove fault
condition.
Cleaning and care
This product has no internal parts
requiring maintenance. Moisture
entering the product may result in
damage.
Ensure no moisture enters the
product during cleaning to
prevent damaging the product
beyond repair.
Do not use abrasive, solvent-
based or aggressive cleaners.
These can damage the surface
of the product.
Only clean the product with a
slightly damp cloth and mild
washing-up liquid.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116

Silvercrest 289484 Operation and Safety Notes

Taper
Operation and Safety Notes

dans d''autres langues