Samsung BD-J7500 Manuel utilisateur

Catégorie
Lecteurs Blu-Ray
Taper
Manuel utilisateur
imagine the possibilities
Thank you for purchasing this Samsung product.
To receive more complete service,
please register your product at
www.samsung.com/register
Blu-ray™ Disc Player
user manual
BD-J7500
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 1 2015-03-03 오전 11:13:48
2 English
Safety Information
• The slots and openings in the cabinet and in
the back or bottom are provided for necessary
ventilation. To ensure reliable operation of this
apparatus, and to protect it from overheating,
these slots and openings must never be
blocked or covered.
- Do not place this apparatus in a confined
space, such as a bookcase, or built-in
cabinet, unless proper ventilation is provided.
- Do not place this apparatus near or over a
radiator or heat register, or where it is exposed
to direct sunlight.
- Do not place vessels (vases etc.) containing
water on this apparatus. A water spill can
cause a fire or electric shock.
• Do not expose this apparatus to rain or place it
near water (near a bathtub, washbowl, kitchen
sink, or pool, etc.). If this apparatus accidentally
gets wet, unplug it and contact an authorised
dealer immediately.
• This apparatus uses batteries. In your
community, there might be environmental
regulations that require you to dispose of these
batteries properly. Please contact your local
authorities for disposal or recycling information.
• Do not overload wall outlets, extension cords or
adaptors beyond their capacity, since this can
result in fire or electric shock.
• Route power-supply cords so that they are
not likely to be walked on or pinched by items
placed on or against them. Pay particular
attention to cords at the plug end, at wall
outlets, and the point where they exit from the
apparatus.
• To protect this apparatus from a lightning storm,
or when it is left unattended and unused for
long periods of time, unplug it from the wall
outlet and disconnect the antenna or cable
system. This will prevent damage to the set due
to lightning and power line surges.
• Before connecting the AC power cord to the
DC adaptor outlet, make sure the voltage
designation of the DC adaptor corresponds to
the local electrical supply.
• Never insert anything metallic into the open
parts of this apparatus. Doing so may create a
danger of electric shock.
• To avoid electric shock, never touch the inside
of this apparatus. Only a qualified technician
should open this apparatus.
• Make sure to plug the power cord in until it is
firmly seated. When unplugging the power cord
from a wall outlet, always pull on the power
cord's plug. Never unplug by pulling on the
power cord. Do not touch the power cord with
wet hands.
• If this apparatus does not operate normally -
in particular, if there are any unusual sounds or
smells coming from it - unplug it immediately
and contact an authorised dealer or service
Centre.
Warning
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE THE COVER (OR BACK). THERE ARE NO USER SERVICEABLE
PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL.
This symbol indicates that high voltage is
present inside. It is dangerous to make any
kind of contact with any internal part of this
product.
This symbol indicates that important
literature concerning operation and
maintenance has been included with this
product.
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 2 2015-03-03 오전 11:13:48
3 English
01 Safety Information
• Maintenance of Cabinet.
- Before connecting other components to this
product, be sure to turn them off.
- If you move your product suddenly from a
cold place to a warm place, condensation
may occur on the operating parts and lens
and cause abnormal disc playback. If this
occurs, unplug the product, wait for two
hours, and then connect the plug to the
power outlet. Then, insert the disc, and try to
play back again.
• Be sure to pull the power plug out of the outlet
if the product is to remain unused or if you are
leaving the house for an extended period of time
(especially when children, elderly, or disabled
people will be left alone in the house).
- Accumulated dust can cause an electric
shock, an electric leakage, or a fire by causing
the power cord to generate sparks and heat
or the insulation to deteriorate.
• Contact an authorised service Centre for
information if you intend to install your
product in a location with heavy dust, high
or low temperatures, high humidity, chemical
substances, or where it will operate 24 hours
a day such as in an airport, a train station, etc.
Failing to do so may lead to serious damage of
your product.
• Use only a properly grounded plug and wall
outlet.
- An improper ground may cause electric shock
or equipment damage. (Class 1 Equipment
only.)
• To turn this apparatus off completely, you must
disconnect it from the wall outlet. Consequently,
the wall outlet and power plug must be readily
accessible at all times.
• Do not allow children to hang on the product.
• Store the accessories (battery, etc.) in a location
safely out of the reach of children.
• Do not install the product in an unstable location
such as a shaky self, a slanted floor, or a
location exposed to vibration.
• Do not drop or strike the product. If the product
is damaged, disconnect the power cord and
contact a service Centre.
• To clean this apparatus, unplug the power cord
from the wall outlet and wipe the product using
a soft, dry cloth. Do not use any chemicals such
as wax, benzene, alcohol, thinners, insecticide,
air fresheners, lubricants, or detergent. These
chemicals can damage the appearance of the
product or erase the printing on the product.
• Do not expose this apparatus to dripping or
splashing. Do not put objects filled with liquids,
such as vases on the apparatus.
• Do not dispose of batteries in a fire.
• Do not plug multiple electric devices into the
same wall socket. Overloading a socket can
cause it to overheat, resulting in a fire.
• There is danger of an explosion if you replace
the batteries used in the remote with the wrong
type of battery. Replace only with the same or
equivalent type.
• WARNING - TO PREVENT THE
SPREAD OF FIRE, KEEP CANDLES
AND OTHER ITEMS WITH OPEN
FLAMES AWAY FROM THIS
PRODUCT AT ALL TIMES.
CLASS 1 LASER product
This Compact Disc player is classified as a CLASS
1 LASER product. Use of controls, adjustments
or performance of procedures other than those
specified herein may result in hazardous radiation
exposure.
CAUTION :
• THIS PRODUCT USES AN INVISIBLE LASER
BEAM WHICH CAN CAUSE HAZARDOUS
RADIATION EXPOSURE IF DIRECTED. BE
SURE TO OPERATE PRODUCT CORRECTLY
AS INSTRUCTED.
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 3 2015-03-03 오전 11:13:48
4 English
Safety Information
• THIS PRODUCT UTILIZES A LASER.
USE OF CONTROLS OR ADJUSTMENTS
OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN
MAY RESULT IN HAZARDOUS RADIATION
EXPOSURE. DO NOT OPEN COVERS AND DO
NOT REPAIR YOURSELF. REFER SERVICING
TO QUALIFIED PERSONNEL.
This product satisfies CE regulations when
shielded cables and connectors are used to
connect the unit to other equipment. To prevent
electromagnetic interference with electric
appliances, such as radios and televisions, use
shielded cables and connectors for connections.
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
LUOKAN 1 LASER LAITE
KLASS 1 LASER APPARAT
PRODUCTO LÁSER CLASE 1
| NOTE |
\
If the Region number of a Blu-ray Disc/DVDs does not
correspond to the Region number of this product, the
product cannot play the disc.
IMPORTANT NOTE
The mains lead on this equipment is supplied with
a molded plug incorporating a fuse. The value of
the fuse is indicated on the pin face of the plug.
If it requires replacing, a fuse approved to BS1362
of the same rating must be used.
Never use the plug with the fuse cover omitted
if the cover is detachable. If a replacement fuse
cover is required, it must be of the same colour as
the pin face of the plug. Replacement covers are
available from your dealer.
If the fitted plug is not suitable for the power points
in your house or the cable is not long enough to
reach a power point, you should obtain a suitable
safety approved extension lead or consult your
dealer for assistance.
However, if there is no alternative to cutting off the
plug, remove the fuse and then safely dispose of
the plug. Do not connect the plug to a mains jack,
as there is a risk of shock hazard from the bared
flexible cord.
To disconnect the apparatus from the mains, the
plug must be pulled out from the mains socket,
therefore the mains plug shall be readily operable.
The product unit accompanying this user manual
is licenced under certain intellectual property rights
of certain third parties.
Precautions
Important Safety Instructions
Read these operating instructions carefully before
using the unit. Follow all the safety instructions
listed below.
Keep these operating instructions handy for future
reference.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install
in accordance with the manufacturer's
instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including AV receivers) that
produce heat.
9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong are provided for your safety.
If the provided plug does not fit into your
outlet, consult an electrician for replacement
of the obsolete outlet.
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 4 2015-03-03 오전 11:13:49
5 English
01 Safety Information
10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where it exits the
apparatus.
11. Only use attachments/accessories specified
by the manufacturer.
12. Use only with the cart,
stand, tripod, bracket,
or table specified by the
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms
or when unused for long periods of time.
14. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as when the power-supply cord or plug
is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does
not operate normally, or has been dropped.
Using the 3D function
IMPORTANT HEALTH AND SAFETY INFORMATION
FOR 3D PICTURES.
Read and understand the following safety
information before using the 3D function.
• Some viewers may experience discomfort while
viewing 3D TV such as dizziness, nausea, and
headaches.
If you experience any such symptom, stop
viewing 3D TV, remove the 3D Active Glasses,
and rest.
• Watching 3D images for an extended period of
time may cause eye strain. If you feel eye strain,
stop viewing 3D TV, remove your 3D Active
Glasses, and rest.
• A responsible adult should frequently check on
children who are using the 3D function.
If there are any reports of tired eyes, headaches,
dizziness, or nausea, have the child stop viewing
3D TV and rest.
• Do not use the 3D Active Glasses for other
purposes (such as general eyeglasses,
sunglasses, protective goggles, etc.).
• Do not use the 3D function or 3D Active Glasses
while walking or moving around. Using the 3D
function or 3D Active Glasses while moving
around may cause you to bump into objects,
trip, and/or fall, and cause serious injury.
• If you want to enjoy 3D content, connect a 3D
device (3D compliant AV receiver or TV) to the
player's HDMI OUT port using a high-speed
HDMI cable. Put on 3D glasses before playing
the 3D content.
• The player outputs 3D signals only through
HDMI cable connected to the HDMI OUT port.
• The video resolution in 3D play mode is
determined by the resolution of the original 3D
video. You can not change the resolution.
• Some functions such as BD Wise, screen size
adjustment, and resolution adjustment may not
operate properly in 3D play mode.
• You must use a high-speed HDMI cable for
proper output of the 3D signal.
• Stay at least three times the width of the screen
from the TV when watching 3D images. For
example, if you have a 46-inch screen, stay 138
inches (11.5 feet) from the screen.
• Place the 3D video screen at eye level for the
best 3D picture.
• When the player is connected to some 3D
devices, the 3D effect may not function properly.
• This player does not convert 2D content into
3D.
• "Blu-ray 3D" and "Blu-ray 3D" logo are
trademarks of the Blu-ray Disc Association.
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 5 2015-03-03 오전 11:13:49
6 English
Contents
SAFETY INFORMATION
2 Warning
4 Precautions
4 Important Safety Instructions
5 Using the 3D function
GETTING STARTED
8 Accessories
9 Front Panel
9 Rear Panel
10 Remote Control
10 Tour of the Remote Control
CONNECTIONS
11 Connecting to a TV
12 Connecting to an Audio System
12 Method 1 Connecting to an HDMI
compatible AV receiver that supports pass
through
13 Method 2
Connecting to an HDMI
compatible AV receiver that does not
support pass through
14 Method 3 Connecting to an Audio System
(7.1 Channel Amplifier)
14 Method 4 Connecting to an AV receiver
with a Digital Optical Cable
15 Connecting to a Network Router
15 Wired Network
15 Wireless Network
SETTINGS
16 The Initial Settings Procedure
16 The Home Screen
17 Accessing the Settings Screen
17 Buttons on the Remote Control Used for
the Settings Menu
18 Settings Menu Functions
18 Picture
19 Sound
20 Network
20 Smart Hub
20 System
22 Support
22 Networks and the Internet
22 Configuring Your Network Connection
25 Wi-Fi Direct
26 Upgrading Software
26 Update now
26 Auto Update
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 6 2015-03-03 오전 11:13:49
7 English
Contents
MEDIA PLAY
28 Playing Commercial Discs
28 Disc Storage & Management
28 Playing Photos, Videos, and Music
(Multimedia)
28 Playing Media Content Saved on a USB
Device
29 Playing Media Content Saved in a
Computer/Mobile Device
29 Playing a Disc with User Recorded
Content
31 Controlling Video Playback
31 Buttons on the Remote Control used for
Video Playback
31 Using the Settings Menu During Playback
33 Using the Sort by & Options Menus
34 Controlling Music Playback
34 Buttons on the Remote Control used for
Music Playback
34 Using the Options Menu During Playback
35 Using the Sort by & Options Menus on a
File Screen
35 Repeating Tracks on an Audio CD
35 Shuffling Tracks on an Audio CD
35 Creating a Playlist from an Audio CD
36 Ripping
37 Playing Photo Contents
37 Using the Tools Menu During Playback
37 Using the Sort by & Options Menus
38 Send files
38 Copying Videos, Music or Photos
38 Using the Send Function
NETWORK SERVICES
39 Creating a Samsung Account
40 Before Using Samsung Apps
40 Using Samsung Apps
40 The Samsung Apps Screen at a Glance
41 Starting an Application
42 Screen Mirroring
43 Using the Web Browser
43 Link Browsing and Pointer Browsing
43 The Control Panel at a Glance
45 Using the Setting Menu
46 Linking Your Internet Service Accounts
to the Product
46 BD-LIVE™
APPENDIX
47 Additional Information
47 Notes
49 Resolution according to the contents type
50 Digital Output Selection
51 Troubleshooting
54 Disc and Format Compatibility
54 Disc types and contents your product can
play
54 Disc types your product cannot play
55 Region Code
55 Logos of Discs the product can play
56 Supported Formats
59 Compliance and Compatibility Notice
60 Copy Protection
60 Network Service Disclaimer
61 Licences
63 Specifications
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 7 2015-03-03 오전 11:13:50
8 English
Getting Started
Accessories
Check for the supplied accessories shown below.
APPS
PANDORA
DIGITAL
SUBTITLE
INPUT
HOME
1
4
7
VOL
+
2
5
8
0
VOL
3
6
9
SOURCE
DISC MENU
SMART
TITLE MENU
VOL VOL
POPUP
A B C D
SEARCH FULLSUBTITLE
SCREEN
SAMSUNG TV
+
INFOTOOLS
RETURN
EXIT
HOME
AUDIO
REPEAT
HUB
Batteries for Remote Control (AAA Size) Remote Control
User Manual HDMI cable
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 8 2015-03-03 오전 11:13:50
9 English
02 Getting Started
Front Panel
| NOTES |
\
To upgrade the product's software through the USB HOST jack, you must use a USB memory stick.
\
When the product displays the Blu-ray Disc's menu, you cannot start the movie by pressing the Play button on the product
or the remote control. To play the movie, you must select Play Movie or Start in the disc's menu, and then press the
v
button on the remote control.
\
To use Anynet+ (HDMI-CEC) function, connect an HDMI cable to the HDMI 1 terminal.
When you connect the HDMI 2 terminal, Anynet+ (HDMI-CEC) function will not be available.
Rear Panel
POWER BUTTON
USB HOST
REMOTE CONTROL SENSOR
DISC TRAY
PLAY/PAUSE BUTTON
OPEN/CLOSE BUTTON
STOP BUTTON
DISPLAY
HDMI OUT
HDMI 1 outputs audio and video
HDMI 2 outputs audio only
LAN
DIGITAL AUDIO OUT7.1CH ANALOG AUDIO OUT
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 9 2015-03-03 오전 11:13:51
10 English
Getting Started
Remote Control
Tour of the Remote Control
Installing batteries
| NOTE |
\
If the remote control does not operate properly:
- Check the polarity +/– of the batteries.
- Check if the batteries are drained.
- Check if the remote sensor is blocked by obstacles.
- Check if there is any fluorescent lighting nearby.
| CAUTION |
\
Dispose of batteries according to local environmental
regulations. Do not put them in the household trash.
APPS
PANDORA
DIGITAL
SUBTITLE
INPUT
HOME
1
4
7
VOL+
2
5
8
0
VOL
3
6
9
SOURCE
DISC MENU
SMART
TITLE MENU
VOL VOL
POPUP
A B C D
SEARCH FULLSUBTITLE
SCREEN
SAMSUNG TV
+
INFOTOOLS
RETURN
EXIT
AUDIO
REPEAT
HUB
HOME
After setup, allows you to set the input
source on your TV.
(This button is only available for Samsung TVs.)
Turn the player on and off.
Press to open and close the disc tray.
Press the number buttons to operate
options.
Use to enter the disc menu.
Press to skip backwards or forwards.
Press to stop a disc.
Press to use Apps.
Press to move to the Home screen.
Press to use the Tools menu.
Return to the previous menu.
Press to search contents.
Use to access various audio functions on a
disc.
These buttons are used both for menus
on the player and also several Blu-ray Disc
functions.
Turn the TV on and off.
(This button is only available for Samsung
TVs.)
TV volume adjustment.
(This button is only available for Samsung
TVs.)
Use to enter the Popup menu/Title menu.
Press to search backwards or forwards.
Press to pause a disc.
Press to play a disc.
Allows you to repeat a title, chapter, track
or disc.
Use to display the playback information.
Use to select menu items and change
menu values.
Press to exit the menu.
Press to switch the Blu-ray Disc/DVD's
subtitle language.
Press to use the full screen function.
During the Blu-ray Disc/DVDs playback, this
button does not operate.
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 10 2015-03-03 오전 11:13:51
11 English
03 Connections
Connections
Connecting to a TV
Connect an HDMI cable from the HDMI OUT jack on the back of the product to the HDMI IN jack on your TV.
- Do not connect the power cord to the wall outlet until you have made all the other connections.
- When you change the connections, turn off all devices before you start.
| NOTES |
\
To use the Anynet+ (HDMI-CEC) function, connect the HDMI cable to the HDMI 1 terminal.
If you connect the cable to the HDMI 2 terminal, the Anynet+ (HDMI-CEC) function will not be available.
- The HDMI 2 terminal does not output a video signal.
\
If you use an HDMI-to-DVI cable to connect to your display device, you must also connect the DIGITAL AUDIO OUT on the
product to an audio system to hear audio.
\
An HDMI cable outputs digital video and audio, so you don't need to connect an audio cable.
\
Depending on your TV, certain HDMI output resolutions may not work. Please refer to the user manual of your TV.
\
When you connect the product to your TV using an HDMI cable or to a new TV, and then turn it on for the first time, the
product automatically sets the HDMI output resolution to the highest supported by the TV.
\
A long HDMI cable may cause screen noise. If this occurs, set HDMI Deep Colour to Off in the menu.
\
To view video in the HDMI 720p, 1080i, 1080p or 2160p output mode, you must use a high speed (category 2) HDMI cable.
\
HDMI outputs only a pure digital signal to the TV.
If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise appears on the screen.
Audio
Video
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 11 2015-03-03 오전 11:13:52
12 English
Connections
Connecting to an Audio System
You can connect this product to an audio system using the methods illustrated below.
- Do not connect the power cord to the wall outlet until you have made all the other connections.
- When you change the connections, turn off all devices before you start.
Method 1 Connecting to an HDMI compatible AV receiver that supports pass through
• Connect an HDMI cable from the HDMI OUT 1 jack on the back of the product to the HDMI IN jack
on your receiver. Connect another HDMI cable from the HDMI OUT jack of your receiver to the HDMI
IN jack of your TV.
• Best quality (Recommended)
- Your receiver must have UHD pass through capability to pass through UHD video content.
Audio/Video
Video
HDMI
compatible
AV receiver
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 12 2015-03-03 오전 11:13:53
13 English
03 Connections
Method 2
Connecting to an HDMI compatible AV receiver that does not support pass through
• Connect an HDMI cable from the HDMI OUT 1 jack on the back of the product to the HDMI IN jack
on your your TV. Connect another HDMI cable from the HDMI OUT 2 jack on the product to the HDMI
IN jack on your receiver.
• Best quality (Recommended)
| CAUTION |
\
Do not connect the HDMI OUT 1 and HDMI OUT 2 terminals of the product with an HDMI cable.
VideoAudio
AV Receiver
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 13 2015-03-03 오전 11:13:53
14 English
Connections
Method 3 Connecting to an Audio System (7.1 Channel Amplifier)
• Using 7.1CH audio cables (not supplied), connect the 7.1CH ANALOG AUDIO OUT terminals on the
rear of the Player to the 7.1CH ANALOG AUDIO IN terminals of your Amplifier.
• Better Quality
Method 4 Connecting to an AV receiver with a Digital Optical Cable
• Using a digital Optical cable (not supplied), connect the OPTICAL DIGITAL AUDIO OUT jack on the
product to the DIGITAL OPTICAL IN jack of the receiver.
• Good quality
• You will hear sound only through the front two speakers with Digital Output set to PCM.
| NOTES |
\
The front left and right outputs on your player and 7.1 channel amplifier must be connected to hear disc menu audio from
certain Blu-ray discs.
\
When connecting to a 5.1 channel home Theatre or receiver, connect all the Analogue Audio output jacks from the player
except for the Surround Back Left and Surround Back Right outputs.
\
If you connect a receiver to the player's OPTICAL DIGITAL AUDIO OUT port, receiver’s audio reproduction may not synchronize
with that of the TV.
SURR. : SURROUND
SURROUND BACK
Audio
7.1 Channel
Amplifier
Method 4Method 3
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 14 2015-03-03 오전 11:13:53
15 English
03 Connections
Connecting to a Network Router
You can connect your product to your network
router using one of the methods illustrated below.
To use the DLNA network functionality, you must
connect your PC to your network as shown in the
illustrations.
The connection can be wired or wireless.
Wired Network
| NOTES |
\
Your router or your Internet Service Provider's policies
may prevent the product from accessing Samsung's
software update server. If this occurs, contact your
Internet Service Provider (ISP) for more information.
\
DSL users, please use a router to make a network
connection.
Wireless Network
| NOTES |
\
If your wireless router supports DHCP, this product can
use a DHCP or static IP address to connect to the wireless
network.
\
Set your wireless router to Infrastructure mode.
Ad-hoc mode is not supported.
\
The product supports only the following wireless security
key protocols:
- WEP (OPEN/SHARED), WPA-PSK (TKIP/AES),
WPA2-PSK (TKIP/AES)
\
Select a channel on the wireless router that is not
currently being used. If the channel set for the wireless
router is currently being used by another device nearby, it
will result in interference and communication failure.
\
If you select the Pure High-throughput (Greenfield)
802.11n mode and set the Encryption type on your router
to WEP, TKIP or TKIP-AES (WPS2Mixed), the product will
not support a connection in compliance with new Wi-Fi
certification specifications.
\
Wireless LAN, by its nature, may cause interference,
depending on the operating conditions (router
performance, distance, obstacles, interference by other
radio devices, etc).
Broadband
service
Broadband
service
Broadband modem
(with integrated router)
Broadband
modem
Router
Or
Broadband
service
Wireless Router
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 15 2015-03-03 오전 11:13:54
16 English
SettingsSettings
The Initial Settings Procedure
• The Home screen will not appear if you do not
configure the initial settings.
• The OSD (On Screen Display) may change in this
product after you upgrade the software version.
• The access steps may differ depending on the menu
you selected.
After you have connected the product to your
TV, turn on the TV and product. When you turn
on the product the first time, the product's Initial
Settings screen appears on the TV. The Initial
Settings procedure lets you set the On Screen
Display (OSD) and menu languages, the aspect
ratio (screen size), and network configuration,
and connect the player to the Internet. Follow the
directions on the screen.
When the initial setup is completed, a tutorial
screen explaining how to use the Home menu will
appear. To exit this screen, press the EXIT button
on the remote.
| NOTES |
\
If you skip Network Setup during the Initial Settings
procedure, you can configure your network settings later.
See "Configuring Your Network Connection" on pages
22~25 for instructions.
\
If you want to display the Initial Settings screen again and
make changes, select Settings > System > Setup in
the Home screen or select the Reset option. (See page
22)
\
If you want to use the Anynet+(HDMI-CEC) function,
please follow the instructions below.
1) Connect the product to an Anynet+(HDMI-CEC)-
compliant Samsung TV using an HDMI Cable.
2) Set the Anynet+(HDMI-CEC) feature to On in both the
TV and the product.
3) Set the TV to the Initial Settings Procedure.
The Home Screen
WebBrowser
2 3
SAMSUNG APPS
1 2 3
No Disc
1 2
6
5
7 8 9
MULTIMEDIAPLAY DISC
RECOMMENDED MY APPS
Screen Mirroring
Settings
3 4
0
1
PLAY DISC : Lets you play photos, videos, or music
content from a Disc.
2
MULTIMEDIA : Lets you play photos, videos, or
music content from USB or mobile devices or PCs.
3
Sign In : Lets you log into your Samsung account.
4
Search : Lets you search for content in Apps and
YouTube by entering corresponding search words.
5
Help : The tutorial screen explaining how to use the
Home menu will appear.
6
SAMSUNG APPS : Gives you access to various
applications you can download.
7
RECOMMENDED : Gives you direct access to
recommended applications.
8
MY APPS : Apps downloaded from MY APPS are
displayed.
9
Screen Mirroring : Lets you view the screen of
your smart phone or android tablet on a TV you
have connected to this product.
0
Settings : Opens the product's menu. In the menu,
you can set various functions to suit your personal
preferences.
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 16 2015-03-03 오전 11:13:54
17 English
04 Settings
| NOTE |
\
If you leave the product in the stop mode for more than
5 minutes without using it, a screen saver will appear on
your TV. If the product is left in the screen saver mode for
more than 20 minutes, the power will automatically turn off.
Accessing the Settings Screen
1. Select Settings on the Home screen, and
then press
v
button. The Settings screen
appears.
Settings
Picture
Sound
Network
Smart Hub
System
Support
Picture
UHD Output Auto
3D Settings
TV Aspect Ratio 16:9 Original
BD Wise Off
Resolution Auto
Movie Frame (24 fps) Auto
DVD 24 fps Conversion Off
2. To access the menus, sub-menus, and
options on the Settings screen, please refer
to the remote control illustration in the next
column.
Buttons on the Remote Control Used
for the Settings Menu
APPS
PANDORA
DIGITAL
SUBTITLE
INPUT
HOME
1
4
7
VOL
+
2
5
8
0
VOL
3
6
9
SOURCE
DISC MENU
SMART
TITLE MENU
VOL VOL
POPUP
A B C D
SEARCH FULLSUBTITLE
SCREEN
SAMSUNG TV
+
INFOTOOLS
RETURN
EXIT
HOME
AUDIO
REPEAT
HUB
1
2 4
3
1
HOME button : Press to move to the Home screen.
2
RETURN button : Press to return to the previous
menu.
3
v
(Enter) / DIRECTION buttons :
• Press ▲▼◄► to move the cursor or select an
item.
• Press the
v
button to activate the currently
selected item or confirm a setting.
4
EXIT button : Press to exit the current menu.
Detailed Function Information
Each Settings function, menu item, and individual
option is explained in detail on-screen. To view an
explanation, use the ▲▼◄► buttons to select the
function, menu item, or option. The explanation
will usually appear on the right side of the screen.
A short description of each Settings function
starts on the next page. Additional information on
some of the functions is also in the Appendix of
this manual.
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 17 2015-03-03 오전 11:13:55
18 English
Settings
Settings Menu Functions
Picture
UHD Output
This option outputs HDMI video at UHD (Ultra
High Definition) resolution. This is only available
when Movie Frame is set to Auto.
| NOTES |
\
To use this feature, you must connect the product to
a device that supports UHD resolution and you must
have content that plays at 24 fps (film speed).
\
This device cannot play UHD content. However, it can
scale up content resolution lower than Full HD to UHD.
\
When you select UHD Output, only 2160 x 3840, 24
frame per second output is available.
3D Settings
Select whether to play a Blu-ray Disc with 3D
content in 3D Mode.
If you move to the Home or SAMSUNG APPS
screen while in 3D mode, the product will switch
to 2D mode automatically.
TV Aspect Ratio
Lets you adjust the output of the product to the
screen size and screen format of your TV.
BD Wise
BD Wise is Samsung's latest inter-connectivity
feature.
When you connect a Samsung product and a
Samsung TV with BD Wise to each other via
HDMI, and BD Wise is on in both the product
and TV, the product outputs video at the video
resolution and frame rate of the Blu-ray Disc/DVD.
Resolution
Set the output resolution of the HDMI video
signal to BD Wise, Auto, 1080p, 1080i, 720p or
576p/480p.
The number indicates the number of lines of video
per frame.
The i and p indicate interlaced and progressive
scan, respectively. Generally, the more lines, the
higher quality.
Movie Frame (24 fps)
If the product is connected to a 24 fps compatible
TV, setting the Movie Frame (24 fps) feature to
Auto lets the product adjust its HDMI output to
24 frames per second automatically for improved
picture quality.
•
You can enjoy the Movie Frame (24 fps) feature
only on a TV supporting this frame rate.
•
Movie Frame is only available when the product
is in the HDMI 1080i or 1080p output resolution
modes.
DVD 24 fps Conversion
Converts DVD playback to 24 frames per second
and outputs it via HDMI. This option is only
available when Movie Frame (24 fps) is set to
On.
| NOTE |
\
This feature applies to NTSC discs only.
Fit Screen Size
Set the screen to the optimal size. (Available for
Smart Hub and Screen Mirroring only)
HDMI Colour Format
Lets you set the Colour space format for the HDMI
output so that it matches the capabilities of the
connected device (TV, monitor, etc). The screen
goes black momentarily after you have selected a
format.
HDMI Deep Colour
Lets you set the product to output HDMI video
with Deep Colour. Deep Colour provides more
accurate Colour reproduction with greater Colour
depth.
Progressive Mode
Lets you improve picture quality when viewing
DVDs.
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 18 2015-03-03 오전 11:13:55
19 English
04 Settings
Sound
Speaker Settings
You can configure this product to connect to a
Multiroom Link compatible speaker wirelessly and
enjoy rich sound.
Settings : You can adjust volume level and
distance for connected product.
Speaker Settings : You can set up speakers
that are connected via your home network.
| NOTES |
\
To use this feature, you must connect at least one
Multiroom Link speaker.
\
Sound quality may be affected by the condition of your
wireless network.
\
The network connection can be negatively affected
and even lost if the network environment deteriorates
over time.
\
Activating Screen Mirroring disables Multiroom Link.
\
For further details, refer to the Multiroom Link manual
on the Samsung web site: www.samsung.com
;
;
Search for Product name: BD-
J7500
;
Manuals
;
Multiroom Link
;
Download
PDF
\
The audio from each connected device may lag behind
the video and audio of the device which is playing the
source contents.
Digital Output
Lets you select the digital audio output format that
is suitable for your TV or AV Receiver. For more
details, see the digital output selection table on
page 50.
PCM Downsampling
Lets you choose to have 96kHz PCM signals
downsampled to 48kHz before they are outputted
to an amplifier. Choose On if your amplifier or
receiver is not compatible with a 96kHz signal.
Dynamic Range Control
Lets you apply dynamic range control to Dolby
Digital, Dolby Digital Plus, and Dolby TrueHD
audio.
Auto : Automatically controls the dynamic range
of Dolby TrueHD audio, based on information
in the Dolby TrueHD soundtrack. Also turns
dynamic range control on for Dolby Digital and
Dolby Digital Plus.
Off : Leaves the dynamic range uncompressed,
letting you hear the original sound.
On : Turns dynamic range control on for all three
Dolby formats. Quieter sounds are made louder
and the volume of loud sounds is reduced.
Downmixing Mode
Lets you select the multi-channel downmix method
that is compatible with your stereo system.
You can choose to have the product downmix to
normal stereo or to surround compatible stereo.
DTS Neo:6 Mode
You can enjoy multichannel sound via HDMI
output from a 2 channel audio source.
Audio Sync
In some cases when the product is connected to
a digital TV, the audio signal may not synchronize
with the video signal. If this occurs, adjust the
audio delay time to match the video signal.
•
You can set the audio delay time between 0 ms
and 250 ms. Adjust it to the optimal setting.
| NOTE |
\
The audio delay time you specify may not be exact
depending on the played content.
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 19 2015-03-03 오전 11:13:55
20 English
Settings
HDMI Audio Output
Set HDMI audio to output through HDMI1 or
HDMI2.
Auto : Audio output will be set automatically
based on the devices connected to HDMI1 and
HDMI2.
HDMI1 : Audio will output to the device connected
to HDMI1.
HDMI2 : Audio will output to the device connected
to HDMI2.
Network
Network Status
Lets you check the current network and Internet
status.
Network Settings
Configure the network connection so you can
enjoy various features such as Internet services
or DLNA functionality, and perform Software
Updates.
Wi-Fi Direct
Lets you connect a Wi-Fi Direct device to the
product using a peer-to-pear network, without the
need for a wireless router.
Note that if the product is connected to a wireless
network, it may be disconnected when you use
Wi-Fi Direct.
| NOTE |
\
Text files, such as files with a .TXT or .DOC extension,
will not display when you are using the Wi-Fi Direct
function.
Multimedia Device Settings
Lets you control which devices on your network,
such as smart phones and tablets, can share
content with your product.
Device Name
Lets you input a name for the product that will
identify it on your network.
BD-Live Settings
Set various BD-Live functions. BD-Live allows you
to access extra features available on some Blu-ray
Discs if you are connected to the Internet.
BD-Live Internet Connection : Lets you fully
allow, partly allow, or prohibit a BD-Live Internet
connection.
BD Data Management : Manage BD data
downloaded from a BD-Live service or Blu-ray
Disc.
Smart Hub
Terms & Policy
You must review and agree to both the App Terms
& Conditions and the privacy policy to use App
services.
Reset Smart Hub
Resets all Smart Hub settings to their default
settings. To use, you must enter the security PIN.
System
Setup
Lets you re-run the Initial Settings procedure.
Quick Start
Lets you set the product to turn on quickly by
decreasing the boot time.
| NOTE |
\
If this function is set to On, Standby power
consumption will be increased.
[BD-J7500-ZN]AK68-02613R-00ENG-.indd 20 2015-03-03 오전 11:13:55
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176
  • Page 177 177
  • Page 178 178
  • Page 179 179
  • Page 180 180
  • Page 181 181
  • Page 182 182
  • Page 183 183
  • Page 184 184
  • Page 185 185
  • Page 186 186
  • Page 187 187
  • Page 188 188
  • Page 189 189
  • Page 190 190
  • Page 191 191
  • Page 192 192

Samsung BD-J7500 Manuel utilisateur

Catégorie
Lecteurs Blu-Ray
Taper
Manuel utilisateur

dans d''autres langues