Ashley AWC31M Mode d'emploi

Marque: Ashley

Modèle: AWC31M

Catégorie: Poêle à bois

Taper: Mode d'emploi

Ce manuel convient également à

AWC21
AWC31

Owner’s Operation and Instruction Manual

MODEL: AWC31

SAFETY NOTICE:

If this heater is not properly installed, a house re

may result. For your safety, follow the installation

instructions. Never use make-shift compromises

during the installation of this heater. Contact local

building or re ofcials about permits, restrictions

and installation requirements in your area.

CAUTION!

Please read this entire manual before you install

or use your new room heater. Failure to follow

instructions may result in property damage,

bodily injury, or even death.

Improper Installation Could Void

Your Warranty!

CONFORMS TO UL STD 1482 and CERTIFIED TO ULC STD S627

WASHINGTON STATE APPROVED

MOBILE HOME APPROVED (U.S. ONLY)

SAVE THESE INSTRUCTIONS

THIS MANUAL WILL HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND ENABLE YOU

TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

852808C-3302G

French version is available for download from the U. S. Stove website: http://www.usstove.com/

La version française est disponible pour téléchargement à partir du site U. S. Stove: http://www.usstove.com/

United States Stove Co.

227 Industrial Park Road P.O. Box 151

South Pittsburg, TN 37380

(800) 750-2723 • www.usstove.com

U.S. Environmental Protection Agency

Certied to comply with 2015 particulate emissions standards.

-2-

OPTIONAL ACCESSORIES

DESCRIPTION PART #

Outside Air Intake Kit 50FAK

CONGRATULATIONS!

You’ve purchased a heater from North America’s oldest manufacturer of wood burning products.

By heating with wood you’re helping to CONSERVE ENERGY!

Wood is our only Renewable Energy Resource. Please do your part to preserve our wood supply. Plant at least

one tree each year. Future generations will thank you.

The instructions pertaining to the installation of your wood stove comply with UL-1482 and ULC-S627 standards.

This manual describes the installation and operation of the Ashley, AWC31 wood heater.

This heater meets the 2015 U.S. Environmental Protection Agency’s crib wood emission limits for wood heaters

sold after May 15, 2015. Under specic test conditions this heater has been shown to deliver heat at rates

ranging from 11,817 to 31,713 Btu/hr. Note: The BTU ratings mentioned above are based on the EPA test

protocol burning dimensional Douglas Fir lumber. Our advertised BTU’s are based on the rst hour of operation

at high burn rate burning cordwood.

CAUTIONS:

• Hot while in operation. Keep children, clothing and furniture away. Contact may cause skin burns.

• Do not use chemicals or uids to ignite the re.

• Do not leave the stove unattended when the door is slightly opened.

• Do not burn garbage, ammable uid such as gasoline, naphtha or motor oil.

• Do not connect to any air distribution duct or system.

• Always close the door after the ignition.

Combustible: Wood

Colors: Metallic Black

Flue Pipe Diameter: 6” (152.5mm)

Flue Pipe Type: (Standard Single Wall or Double

Wall):

Black or Blued Steel 2100°F (650°C)

Minimum Chimney Hieght: 12’ (3.7m)

Maximum Log Length: 21” (533.5mm)

Dimensions

Overall:

Depth x Width x Height:

22” x 30” x 31.25” (559mm x 762mm x 794mm)

Combustion Chamber:

Width x Depth:

22 3/4” x 12” (578mm x 305mm)

Volume:

Cubic Feet:

1.86 ft³ (.0527m³)

Door Opening: Width x Height: 16” x 8” (406.5mm x 203mm)

Pyroceramic Glass Door: (Viewing) Width x Height: 13 13/16” x 8 3/8” (351mm x 213mm)

Note: Register your product on line at www.usstove.com. See “Limited Warranty” section for specic warranty

information for your new purchase. Save your receipt with your records for any claims.

-3-

TOOLS AND MATERIALS NEEDED FOR INSTALLATION

You will need a drill with a 1/8” bit to install sheet metal screws into connector pipe. A 5/16” socket/wrench or

screw driver to install pedestal trim, room air deector, and blower assembly described below. A 1/2” socket/

wrench to install ue collar. A non-combustible oor protector as specied in this manual. All chimney and chimney

connector components required for your particular chimney installation. For mobile homes, see page 13.

Assembly

Flue Collar Assembly:

1. Mount the ue collar to the top of the unit as shown using the (3) 5/16-18 x 1-1/2 bolts, (3) washers, and (3)

weld tabs provided in the parts box.

Room Air Deector Assembly:

1. Locate the Room Air Deector. Using the three(3) 1/2 Tek Screws provided, mount the deector to the unit

as shown in the diagram.

Firebrick Conguration:

1. Replace the Firebrick as shown in the illustration below.

Side view of ue collar

mount to heater top

Brick Conguration

HEATER

TOP

WELD

TAB

5/16-18 x 1-1/2

BOLT

SECTION A-A

SCALE .1

A A

B B

TOLERANCES

EXCEPT

NOTED

HOLES

 .005"

DECIMAL



.XX = 0.03 XXX = 0.010

ANGULAR

 2 

DESCRIPTION

FINISH

REFERENCE

SCALE

DWN BY

DATE

SIZE

REV

TITLE NUMBER

UNITED STATES STOVE COMPANY

ESTABLISHED 1869

ASHLEY CAST HEATER AC2000

AC2000

TOP ASSEMBLY

WHO

6/18/2013

OF 3

SHEET

THE DATA CONTAINED HEREIN IS PROPRIETARY TO U. S.

STOVE COMPANY. THIS DATA SHALL NOT BE DUPLICATED,

TRANSFERRED, MADE AVAILABLE, OR USED BY ANY THIRD

PARTY FOR ANY PURPOSE EXCEPT SPECIFICALLY

AUTHORIZED IN WRITING BY U. S. STOVE COMPANY.

GENERAL NOTES:

ALL FORMED DIMENSIONS ARE TO

THE OUTSIDE OF THE PART,

UNLESS SPECIFIED OTHERWISE.

A A

REVISION HISTORY

REV DESCRIPTION DATE BY

A INITIAL RELEASE

Date

Who?

-4-

ASSEMBLY INSTRUCTIONS

Blower Assembly

THE BLOWER ASSEMBLY MUST BE DISCONNECTED FROM THE SOURCE OF ELECTRICAL SUPPLY BEFORE ATTEMPTING

THE INSTALLATION.

THE BLOWER ASSEMBLY IS INTENDED FOR USE ONLY WITH A STOVE THAT IS MARKED TO INDICATE SUCH USE.

DO NOT ROUTE THE SUPPLY CORD NEAR OR ACROSS HOT SURFACES!

Step 1.

Fix the assembly to the back of the stove with the four screws provided.

ASH PAN ASSEMBLY

Remove ash pan from rebox. Under the rebox, there are two brackets; Slide the ash pan into these brackets.

NOMENCLATURES DES PIÈCES

QTÉ

TITRE

No DE PIÈCE

ARTICLE

1GOUPILLE CYLINDRIQUE 3/8 x 1-1/4 835061

10-24 X 3/8 po PH PN HD MS 832022

RONDELLE PLATE 7/32 po DI x 1/2 po DE x 3/64

832783

5 pi

JOINT D'ÉTANCHÉITÉ DE CORDON 5/8 po

880664

1VERRE DE PORTE (40564) 891813

4 pi

JOINT D'ÉTANCHÉITÉ, FENÊTRE, 125 x 1 L/PSA

880876

2SUPPORT, VERRE DU BAS25465

PORTE, RECTANGULAIRE, GRANDE

405698

SCELLANT, SILICONE, NOIR

892849

POIGNÉE DE PORTE PEINTE

2569210

LES EXTRÉMITÉS COUPÉES DU JOINT DE VERRE

DOIVENT SE RENCONTRER AU BAS ET AU CENTRE DU VERRE.

C LES EXTRÉMITÉS COUPÉES DU JOINT DE VERRE DOIVENT

SE RENCONTRER ENTRE LES PATTES D'ARTICULATION.

4 9

NOMENCLATURES DES PIÈCES

QTÉ

TITRE

No DE PIÈCE

ARTICLE

1GOUPILLE CYLINDRIQUE 3/8 x 1-1/4 835061

10-24 X 3/8 po PH PN HD MS 832022

RONDELLE PLATE 7/32 po DI x 1/2 po DE x 3/64

832783

5 pi

JOINT D'ÉTANCHÉITÉ DE CORDON 5/8 po

880664

1VERRE DE PORTE (40564) 891813

4 pi

JOINT D'ÉTANCHÉITÉ, FENÊTRE, 125 x 1 L/PSA

880876

2SUPPORT, VERRE DU BAS25465

PORTE, RECTANGULAIRE, GRANDE

405698

SCELLANT, SILICONE, NOIR

892849

POIGNÉE DE PORTE PEINTE

2569210

LES EXTRÉMITÉS COUPÉES DU JOINT DE VERRE

DOIVENT SE RENCONTRER AU BAS ET AU CENTRE DU VERRE.

C LES EXTRÉMITÉS COUPÉES DU JOINT DE VERRE DOIVENT

SE RENCONTRER ENTRE LES PATTES D'ARTICULATION.

4 9

-5-

INSTALLATION

SAFETY NOTICE

• If this stove is not properly installed, a house re may result. To reduce the risk of re, follow the installation

instructions.

• Consult your municipal building department or re ofcials about permits, restrictions and installations

requirements in your area.

• Use smoke detectors in the room where your stove is installed.

• Keep furniture and drapes well away from the stove.

• Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter uid, or similar liquids to start or

“freshen up” a re in this heater. Keep all such liquids well away from the heater while it is in use.

• In the event of a chimney re, push the air control full closed to deprive the re of oxygen. Call the re

department.

• Do not connect to any air distribution duct or system.

• A source of fresh air into the room or space heated shall be provided when required.

POSITIONING THE STOVE

It is very important to position the wood stove as close as possible to the chimney, and in an area that will favor

the most efcient heat distribution possible throughout the house. The stove must therefore be installed in the

room where the most time is spent, and in the most spacious room possible. Recall that wood stoves produce

radiating heat, the heat we feel when we are close to a wood stove. A wood stove also functions by convection,

that is through the displacement of hot air accelerated upwards and its replacement with cooler air. If necessary,

the hot air distribution from the stove may be facilitated by the installation of a blower.

The wood stove must not be hooked up to a hot air distribution system since an excessive accumulation of heat

may occur. A wood stove must never be installed in a hallway or near a staircase, since it may block the way in

case of re or fail to respect required clearances.

-6-

FLOOR PROTECTOR

Your wood stove should be placed on a 1 inch, non-combustible surface with a k factor of 0.84. For multiple

layers, add R-values of each layer to determine the overall R-value. The R value for the required board is 1.03. If

there is a horizontal section of chimney connector, the oor protector should go under it and 2 inches beyond

each side To calculate R-Values for alternative methods, see “Alternate Floor Protector Calculations” section in

this manual.

The oor protector should exceed the stove as follows:

Dimension Inch mm

H ** Front 16 635

J** Left 6 153

K** Right 6 153

L** Back 1 25

M Total Width 46 1169

N Total Length 53.5 1359

* Canadian installations require 18” (457mm)

** Canadian installations require 8” (203mm)

-7-

CLEARANCES TO COMBUSTIBLES

It is of utmost importance that the clearances to combustible materials be strictly adhered to during installation

of the stove. Refer to the tables below:

• Floor to ceiling height must be at least 7’ (2.13m) in all cases.

• Do not place any combustible material within 4’ (1.2m) of the front of the unit.

• The clearance between the ue pipe and a wall are valid only for vertical walls and for vertical ue pipe.

• The chimney connector must not pass through an attic or roof space, closet or similar concealed space, a

oor, or a ceiling.

• For Canadian installations, where passage through a wall, or partition of combustible construction is desired,

the installation must conform to CAN/CSA-B365.

• A ue pipe crossing a combustible wall must have a minimum clearance of 18” (457.2mm).

• To reduce ue clearances from combustible materials, contact your local safety department.

Dimension Inch mm

A Backwall to Stove 16 406

B Sidewall to Stove 18 457

Wall to corner (Angled

Installation)

12 305

D Backwall to Flue 21.5 546

E Sidewall to Flue 30 762

F Wall to Flue (Angled Installation) 24 610

-8-

CHIMNEY CONNECTOR (STOVE PIPE)

Your chimney connector and chimney must have the same diameter as the stove outlet (6”). If this is not the

case, we recommend you contact your dealer in order to insure there will be no problem with the draft.

The stove pipe must be made of aluminized or cold roll steel with a minimum thickness of 0.021” or 0.53 mm. It is

strictly forbidden to use galvanized steel.

Your smoke pipe should be assembled in such a way that the male section (crimped end) of the pipe faces

down. Attach each of the sections to one another with three equidistant metal screws.

The pipe must be short and straight. All sections installed horizontally must slope at least 1/4 inch per foot, with

the upper end of the section toward the chimney. Any installation with a horizontal run of chimney pipe must

conform to NFPA 211. You may contact NFPA (National Fire Protection Association) and request the latest edition

of the NFPA Standard 211.

To insure a good draft, the total length of the coupling pipe should never exceed 8’ to 10’ (2.4m to 3.04 m).

(Except for cases of vertical installation, cathedral-roof style where the smoke exhaust system can be much

longer and connected without problem to the chimney at the ceiling of the room).

There should never be more than two 90 degrees elbows in the smoke exhaust system.

Installation of a “barometric draft stabilizer” (replace register) on a smoke exhaust system is prohibited.

Furthermore, installation of a draft damper is not recommended. Indeed, with a controlled combustion wood

stove, the draft is regulated upon intake of the combustion air in the stove and not at the exhaust.

IMPORTANCE OF PROPER DRAFT

Draft is the force which moves air from the appliance up through the chimney. The amount of draft in your

chimney depends on the length of the chimney, local geography, nearby obstructions and other factors. Too

much draft may cause excessive temperatures in the appliance. Inadequate draft may cause backpufng into

the room and ‘plugging’ of the chimney.

“Inadequate draft will cause the appliance to leak smoke into the room through appliance and chimney

connector joints. An uncontrollable burn or excessive temperature indicates excessive draft.

-9-

CHIMNEY

Your wood stove may be hooked up with a 6” factory built or masonry chimney. If you are using a factory built

chimney, it must comply with UL 103 or CSA-B365 standard; therefore it must be a Type HT (2100°F). It is extremely

important that it be installed according to the manufacturer’s specications. Take into account the chimney’s

location to insure it is not too close to neighbors or in a valley which may cause unhealthy or nuisance conditions.

If you are using a masonry chimney, it is important that it be built in compliance with the specications of the

National Building Code. It must be lined with re clay bricks, metal or clay tiles sealed together with re cement.

(Round ues are the most efcient).

The interior diameter of the chimney ue must be identical to the stove smoke exhaust. A ue which is too

small may cause draft problems, while a large ue favours rapid cooling of the gas, and hence the build-up of

creosote and the risk of chimney res. Note that it is the chimney and not the stove which creates the draft effect;

your stove’s performance is directly dependent on an adequate draft from your chimney.

The following recommendations may be useful for the installation of your chimney:

1. Do not connect this unit to a chimney ue serving another appliance.

2. It must rise above the roof at least 3’ (0.9m) from the uppermost point of contact.

3. The chimney must exceed any part of the building or other obstruction within a 10’ (3.04m) distance by a

height of 2’ (0.6m).

4. Installation of an interior chimney is always preferable to an exterior chimney. Indeed, the interior chimney

will, by denition, be hotter than an exterior chimney, being heated up by the ambient air in the house.

Therefore the gas which circulates will cool more slowly, thus reducing the build-up of creosote and the risk

of chimney res.

5. The draft caused by the tendency for hot air to rise will be increased with an interior chimney.

6. Using a re screen at the extremity of the chimney requires regular inspection in order to insure that it is not

obstructed thus blocking the draft, and it should be cleaned when used regularly.

-10-

FACTORY BUILT CHIMNEY

When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be followed. You

must also purchase (from the same manufacturer) and install the ceiling support package or wall pass-through

and “T” section package, restops (where needed), insulation shield, roof ashing, chimney cap, etc. Maintain

proper clearance to the structure as recommended by the manufacturer. The chimney must be the required

height above the roof or other obstructions for safety and proper draft operation.

-11-

MASONRY CHIMNEY

Ensure that a masonry chimney meets the minimum standards of the National Fire Protection Association (NFPA)

by having it inspected by a professional. Make sure there are no cracks, loose mortar or other signs of deterioration

and blockage. Have the chimney cleaned before the stove is installed and operated. When connecting the

stove through a combustible wall to a masonry chimney, special methods are needed.

-12-

Method A. 12” (304.8 mm) Clearance to Combustible Wall

Member: Using a minimum thickness 3.5” (89 mm) brick

and a 5/8” (15.9 mm) minimum wall thickness clay liner,

construct a wall pass-through. The clay liner must conform

to ASTM C315 (Standard Specication for Clay Fire Linings)

or its equivalent. Keep a minimum of 12” (304.8 mm) of brick

masonry between the clay liner and wall combustibles. The

clay liner shall run from the brick masonry outer surface to

the inner surface of the chimney ue liner but not past the

inner surface. Firmly grout or cement the clay liner in place

to the chimney ue liner.

Method B. 9” (228.6 mm) Clearance to Combustible Wall

Member: Using a 6” (152.4 mm) inside diameter, listed,

factory-built Solid-Pak chimney section with insulation

of 1” (25.4 mm) or more, build a wall pass-through with a

minimum 9” (228.6 mm) air space between the outer wall of

the chimney length and wall combustibles. Use sheet metal

supports fastened securely to wall surfaces on all sides,

to maintain the 9” (228.6 mm) air space. When fastening

supports to chimney length, do not penetrate the chimney

liner (the inside wall of the Solid-Pak chimney). The inner end

of the Solid-Pak chimney section shall be ush with the inside

of the masonry chimney ue, and sealed with a non-water

soluble refractory cement. Use this cement to also seal to

the brick masonry penetration.

Method C. 6” (152.4 mm) Clearance to Combustible Wall

Member: Starting with a minimum 24 gage (.024” [.61 mm])

6” (152.4 mm) metal chimney connector, and a minimum 24

gage ventilated wall thimble which has two air channels of

1” (25.4 mm) each, construct a wall pass-through. There shall

be a minimum 6” (152.4) mm separation area containing

berglass insulation, from the outer surface of the wall thimble

to wall combustibles. Support the wall thimble, and cover

its opening with a 24-gage minimum sheet metal support.

Maintain the 6” (152.4 mm) space. There should also be a

support sized to t and hold the metal chimney connector.

See that the supports are fastened securely to wall surfaces

on all sides. Make sure fasteners used to secure the metal

chimney connector do not penetrate chimney ue liner.

Method D. 2” (50.8 mm) Clearance to Combustible Wall

Member: Start with a solid-pak listed factory built chimney

section at least 12” (304 mm) long, with insulation of 1” (25.4

mm) or more, and an inside diameter of 8” (2 inches [51 mm]

larger than the 6” [152.4 mm] chimney connector). Use this

as a pass-through for a minimum 24-gauge single wall steel

chimney connector. Keep solid-pak section concentric with

and spaced 1” (25.4 mm) off the chimney connector by

way of sheet metal support plates at both ends of chimney

section. Cover opening with and support chimney section

on both sides with 24 gage minimum sheet metal supports.

See that the supports are fastened securely to wall surfaces

on all sides. Make sure fasteners used to secure chimney ue

line do not penetrate the inner liner.

NOTES:

1. Connectors to a masonry chimney, excepting method B, shall extend in one continuous section through the

wall pass-through system and the chimney wall, to but not past the inner ue liner face.

2. A chimney connector shall not pass through an attic or roof space, closet or similar concealed space, or a

oor, or ceiling.

COMBUSTIBLE WALL CHIMNEY CONNECTOR PASS-THROUGHS

-13-

OUTSIDE COMBUSTION AIR

Your wood stove is approved to be installed with an outside air intake which is necessary for a mobile home.

This type of installation is also required in air tight houses and houses with negative pressure problems. You can

purchase this option through your heater dealer. Make sure to specify the part number mentioned in this booklet.

Installation instructions are supplied with the air intake kit.

Outside combustion air may be required if:

1. Mobile Home Installations

2. Your stove does not draw steadily, smoke rollout occurs, wood burns poorly, or back-drafts occur whether or

not there is combustion present.

3. Existing fuel-red equipment in the house, such as replaces or other heating appliances, smell, do not

operate properly, suffer smoke roll-out when opened, or back-drafts occur whether or not there is combustion

present.

4. Opening a window slightly on a calm (windless) day alleviates any of the above symptoms.

5. The house is equipped with a well-sealed vapor barrier and tight tting windows and/or has any powered

devices that exhaust house air.

6. There is excessive condensation on windows in the winter.

7. A ventilation system is installed in the house.

For use in MOBILE HOMES (U. S. installations ONLY):

• Warning! Do not install in sleeping room.

• Caution! The structural integrity of the mobile home oor, wall, and ceiling/roof must be maintained.

• Install in accordance with 24 CFR, part 3280 (HUD).

• Use a factory built chimney that complies with UL 103 standards; therefore it must be a type ht (2100°f).

• Use a spark arrester.

• The stove must be attached to the structure of the mobile home. Use the mobile home leg fasteners to

secure the unit to the oor.

Illustration: Securing heater to the Floor.

-14-

TYPE WEIGHT

(LBS. CU. FT.,

DRY)

PER CORD EFFICIENCY

RANKING

SPLITS MILLIONS

BTU’s/CORD

Hickory 63 4500 1.0 Well 31.5

White Oak 48 4100 .9 Fair 28.6

Red Oak 46 3900 .8 Fair 27.4

Beech 45 3800 .7 Hard 26.8

Sugar Maple 44 3700 .6 Fair 26.2

Black Oak 43 3700 .6 Fair 25.6

Ash 42 3600 .5 Well 25.0

Yellow Birch 40 3400 .4 Hard 23.8

Red Maple 38 3200 .3 Fair 22.6

Paper Birch 37 3100 .3 Easy 22.1

Elm/Sycamore 34 2900 .2 Very Difcult 20.1

Red Spruce 29 1800 .1 Easy 16.1

WOODSTOVE UTILIZATION

This heater is designed to burn natural wood only. Higher efciencies and lower emissions generally result when

burning air dried seasoned hardwoods, as compared to softwoods or to green or freshly cut hardwoods.

DO NOT BURN:

1. Garbage;

2. Lawn clippings or yard waste;

3. Materials containing rubber, including tires;

4. Materials containing plastic;

5. Waste petroleum products, paints or paint thinners,

or asphalt products;

6. Materials containing asbestos;

7. Construction or demolition debris;

8. Railroad ties or pressure-treated wood;

9. Manure or animal remains;

10. Salt water driftwood or other previously salt water

saturated materials;

11. Unseasoned wood; or

12. Paper products, cardboard, plywood, or

particleboard. The prohibition against burning

these materials does not prohibit the use of re

starters made from paper, cardboard, saw dust,

wax and similar substances for the purpose of

starting a re in an affected wood heater.

Burning these materials may result in release of toxic fumes or render the heater ineffective and cause smoke.

Dead wood lying on the forest oor should be considered wet, and requires full seasoning time. Standing dead

wood can usually be considered to be about 2/3 seasoned. Splitting and stacking wood before it is stored

accelerates drying time. Storing wood on an elevated surface from the ground and under a cover or covered

area from rain or snow also accelerates drying time. A good indicator if wood is ready to burn is to check the

piece ends. If there are cracks radiating in all directions from the center then the wood should be dry enough

to burn. If your wood sizzles in the re, even though the surface is dry, it may not be fully cured, and should be

seasoned longer. Waste and other ammable materials should not be burned in your stove. Any type of wood

may be used in your stove, but specic varieties have better energy yields than others. Please consult the

following table in order to make the best possible choice.

It is EXTREMELY IMPORTANT that you use DRY WOOD only in your wood stove. The wood should have dried for 9

to 15 months, such that the humidity content (in weight) is reduced below 20% of the weight of the log. It is very

important to keep in mind that even if the wood has been cut for one, two or even more years, it is not necessarily

dry, if it has been stored in poor conditions. Under extreme conditions it may rot instead of drying. This point

cannot be over stressed; the vast majority of the problems related to the operation of a wood stove is caused by

the fact that the wood used was too damp or had dried in poor conditions. These problems can be:

- ignition problems - creosote build-up causing chimney res

- low energy yield - blackened windows

- incomplete log combustion

Smaller pieces of wood will dry faster. All logs exceeding 6” in diameter should be split. The wood should not be

stored directly on the ground. Air should circulate through the cord. A 24” to 48” air space should be left between

each row of logs, which should be placed in the sunniest location possible. The upper layer of wood should be

protected from the elements but not the sides.

-15-

TESTING YOUR WOOD

When the stove is thoroughly warmed, place one piece of split wood (about ve inches in diameter) parallel to

the door on the bed of red embers.

Keep the air control full open by pulling on it and close the door. If ignition of the piece is accomplished within

90 seconds from the time if was placed in the stove, your wood is correctly dried. If ignition takes longer, your

wood is damp.

If your wood hisses and water or vapor escapes at the ends of the piece, your wood is soaked or freshly cut.

Do not use this wood in your stove. Large amounts of creosote could be deposited in your chimney, creating

potential conditions for a chimney re. Tamper Warning

This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against federal

regulations to alter this setting or otherwise operate this wood heater in a manner inconsistent with operating

instructions in this manual.

THE FIRST FIRES

The fresh paint on your stove needs to be cured to preserve its quality. Once the fuel charge is properly ignited,

only burn small res in your stove for the rst four hours of operation. Never open the air control more than

necessary to achieve a medium burn rate.

Make sure that there’s enough air circulation while curing the stove. The odors could be smelled during the 3 or

4 rst res. Never start your stove outside. You will not be able to see if you are over heating.

IGNITION

After making sure that the stove air intake controls are fully open (completely pull-out towards you), The top

down method of re building is recommended for this appliance. After making sure that the stove air intake

controls are fully open (completely pull-out towards you), Place the largest pieces of wood on the bottom, laid in

parallel and close together. Smaller pieces are placed in a second layer, crossways to the rst. A third layer of still

smaller pieces is laid crossways to the second, this time with some spaces between. Then a fourth layer of loose,

small kindling and twisted newspaper sheets tops off the pile.

Before igniting the paper and kindling wood, it is recommended that you warm up the chimney. This is done

in order to avoid back draft problems often due to negative pressure in the house. If such is the case, open a

window slightly near the stove and twist together a few sheets of newspaper into a torch. Light up this paper

torch and hold it as close as possible to the mouth of the pipe inside the combustion chamber to warm up the

chimney. Once the updraft movement is initiated, you are ready to ignite the stove by lighting the paper and

kindling wood inside the combustion chamber.

When you have achieved a good bed of hot embers, we recommend the following burn procedures:

Primary Air Settings

(Slide Damper is located in center of stove under hearth

plate)

(Damper Adjustment: Pulling out on damper increases

air)

Electric Blower Speed Setting (Variable)

(Blower is on High when turned “ON”,

Rotate clockwise until stop for “LOW”.)

Burn Rate Adjust Damper from fully closed Burn Time Blower Speed

Low 1/4” (6.3mm) @ 30 minutes Low

Medium - Low 3/8” (9.5mm) @ 30 minutes Low

Medium - High 1/2” (12.7mm) @ 30 minutes Low

High approx. 3” (76mm) all minutes High

CAUTION: Never alter the damper slide or the adjustment range to increase ring for any reason. Doing so could result in

heater damage and will void your warranty.

HEATING

Controlled combustion is the most efcient technique for wood heating because it enables you to select the type

of combustion you want for each given situation. The wood will burn slowly if the wood stove air intake control is

adjusted to reduce the oxygen supply in the combustion chamber to a minimum. On the other hand, wood will

burn quickly if the air control is adjusted to admit a larger quantity of oxygen in the combustion chamber. Refer

to the primary air settings table for damper operation setting. Real operating conditions may give very different

results than those obtained during testing according to the species of wood used, its moisture content, the size

and density of the pieces, the length of the chimney, altitude and outside temperature.

-16-

WARNINGS

• Never overre your stove. If any part of the stove starts to glow red, over ring is happening. Readjust the

air intake control at a lower setting.

• The installation of a log cradle or grates is not recommended in your wood stove. Build re directly on

rebrick.

• Never put wood above the rebrick lining of the rebox.

• Attempts to achieve heat output rates that exceed heater design specications can result in permanent

damage to the heater.

EFFICIENCIES

Efciencies can be based on either the lower heating value (LHV) or the higher heating value (HHV) of the fuel.

The lower heating value is when water leaves the combustion process as a vapor, in the case of woodstoves the

moisture in the wood being burned leaves the stove as a vapor. The higher heating value is when water leaves

the combustion process completely condensed. In the case of woodstoves this would assume the exhaust gases

are room temperature when leaving the system, and therefore calculations using this heating value consider

the heat going up the chimney as lost energy. Therefore, efciency calculated using the lower heating value of

wood will be higher than efciency calculated using the higher heating value. In the United States all woodstove

efciencies should be calculated using the higher heating value.

The best way to achieve optimum efciencies is to learn the burn characteristic of you appliance and burn well-

seasoned wood. Higher burn rates are not always the best heating burn rates; after a good re is established a

lower burn rate may be a better option for efcient heating. A lower burn rate slows the ow of usable heat out

of the home through the chimney, and it also consumes less wood.

The amount of visible smoke being produced can be an effective method of determining how efciently the

combustion process is taking place at the given settings. Visible smoke consist of unburned fuel and moisture

leaving your stove. Learn to adjust the air settings of your specic unit to produce the smallest amount of visible

smoke. Wood that has not been seasoned properly and has a high wood moisture content will produce excess

visible smoke and burn poorly.

OPERATIONAL TIPS

Get the appliance hot and establish a good coal bed before adjusting to a low burn rate (this may take 30

minutes or more depending on your wood)

Use smaller pieces of wood during start-up and a high burn rate to increase the stove temperature

Be considerate of the environment and only burn dry wood

Burn small, intense res instead of large, slow burning res when possible

Learn your appliance’s operating characteristics to obtain optimum performance

Burning unseasoned wet wood only hurts your stoves efciency and leads to accelerated creosote buildup in

your chimney

RELOADING

Once you have obtained a good bed of embers, you should reload the unit. In order to do so, open the air

controls to maximum a few seconds prior to opening the stove’s door. Then proceed by opening the door very

slowly; open it one or two inches for 5 to 10 seconds, before opening it completely to increase the draft and thus

eliminate the smoke which is stagnant in a state of slow combustion in the stove. Then bring the red embers to

the front of the stove and reload the unit.

For optimal operation of your wood stove, we recommend you to operate it with a wood load approximately

equivalent to the height of re bricks.

It is important to note that wood combustion consumes ambient oxygen in the room .In the case of negative

pressure, it is a good idea to allow fresh air in the room, either by opening a window slightly or by installing a fresh

air intake system on an outside wall.

Creosote - Formation and Need for Removal - When wood is burned slowly, it produces tar and other organic

vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively

cool chimney ue of a slow-burning re. As a result, creosote residue accumulates on the ue lining. When ignited

this creosote makes an extremely hot re. The chimney connector and chimney should be inspected at least

once every two months during the heating season to determine if a creosote build-up has occurred. If creosote

has accumulated (3mm or more), it should be removed to reduce the risk of a chimney re.

We strongly recommend that you install a magnetic thermometer on your smoke exhaust pipe, approximately

18” above the stove. This thermometer will indicate the temperature of your gas exhaust fumes within the smoke

exhaust system. The ideal temperature for these gases is somewhere between 275°F and 500°F. Below these

temperatures, the build-up of creosote is promoted. Above 500 degrees, heat is wasted since a too large quantity

is lost into the atmosphere.

-17-

TO PREVENT CREOSOTE BUILD UP

• Always burn dry wood. This allows clean burns and higher chimney temperatures, therefore less creosote

deposit.

• Leave the air control full open for about 5 min. every time you reload the stove to bring it back to proper

operating temperatures. The secondary combustion can only take place if the rebox is hot enough.

• Always check for creosote deposit once every two months and have your chimney cleaned at least once a

year.

If a chimney or creosote re occurs, close all dampers immediately. Wait for the re to go out and the heater to

cool, then inspect the chimney for damage. If no damage results, perform a chimney cleaning to ensure there is

no more creosote deposits remaining in the chimney.

ASH DISPOSAL

Whenever ashes get 3 to 4 inches deep in your rebox or ash pan, and when the re has burned down and

cooled, remove excess ashes. Leave an ash bed approximately 1 inch deep on the rebox bottom to help

maintain a hot charcoal bed.

Ashes should be placed in a metal container with a tight-tting lid. The closed container of ashes should be

placed on a noncombustible oor or on the ground, away from all combustible materials, pending nal disposal.

The ashes should be retained in the closed container until all cinders have thoroughly cooled.

SMOKE AND CO MONITORS

Burning wood naturally produces smoke and carbon monoxide(CO) emissions. CO is a poisonous gas when

exposed to elevated concentrations for extended periods of time. While the modern combustion systems in

heaters drastically reduce the amount of CO emitted out the chimney, exposure to the gases in closed or conned

areas can be dangerous. Make sure you stove gaskets and chimney joints are in good working order and sealing

properly to ensure unintended exposure. It is recommended that you use both smoke and CO monitors in areas

having the potential to generate CO.

CAUTIONS:

• Ashes could contain hot embers even after two days without operating the stove.

• The ash pan can become very hot. Wear gloves to prevent injury.

• Never burn the stove with the ash trap open. This would result in over ring the stove. Damage to the stove

and even house re may result.

MAINTENANCE

Your wood stove is a high efciency stove and therefore requires little maintenance. It is important to perform

a visual inspection of the stove every time it is emptied, in order to insure that no parts have been damaged,

in which case repairs must be performed immediately. Inspect and clean the chimney and connector pipe

periodically for creosote buildup or obstructions.

GLASS

• Inspect and clean the glass regularly in order to detect any cracks. If you spot one, turn the stove off

immediately. Do not abuse the glass door by striking or slamming shut. Do not use the stove if the glass is

broken.

• If the glass on your stove breaks, replace only with the glass supplied from your heater dealer. Never

substitute other materials for the glass.

• To replace the glass, remove the screws retaining the glass mouldings inside the door. Remove the

mouldings and replace the damaged piece with a new one. Perform the procedure backwards after

replacing. When replacing the glass, you should change the glass gasket to make sure you keep it sealed.

• Never wash the glass with a product that may scratch. Use a specialized product, available in the stores

where wood stoves are sold. The glass should be washed only when cold.

-18-

GASKETING

It is recommended that you change the door gasket (which makes your stove door air tight) once a year, in

order to insure good control over the combustion, maximum efciency and security. To change the door gasket,

simply remove the damaged one. Carefully clean the available gasket groove, apply a high temperature

silicone sold for this purpose, and install the new gasket. You may light up your stove again approximately 24

hours after having completed this operation. This unit’s door uses a 1/2” diameter rope gasket.

AIR TUBES

The air tubes assembled in this unit are designed to provide an accurate mix of secondary air to insure the

highest efciency. Any damage or deterioration of these tubes may reduce the efciency of combustion. The

air tubes are held in position by either screws or snap pins. Locate these to either side of the tube and remove to

allow the tube to be removed and replaced.

PAINT

Remember to only clean your stove with a dry soft cloth that will not harm the stoves nish.

Your stove has two types of coatings that are used in the nal nish; porcelain enamel and high temperature

stove paint.

ENAMEL REPAIR

The porcelain enamel nish will maintain its color and luster for the life of the stove. However, because it is glass

it may chip if hit with a hard or sharp object. If you experience a scratch or chip in the porcelain enamel nish,

specially formulated gloss touch up paint can be used. Contact you stove dealer to request a small bottle of this

touch up paint.

1. Ensure the stove is cool.

Note: The paint may be applied to a warm stove, but the temperature of the section to be painted should be

below the boiling temperature

2. (200°F) to achieve a smooth nish.

3. The area should be built up with multiple thin coats.

Note: Better results are obtained if the stove is brought up to operational temperatures between coats.

HIGH TEMPERATURE STOVE PAINT REPAIR

If the painted portions of your stove need re coating it is possible to give those pieces a brand new look by

repainting it with a 1200°F heat resistant stove paint.

1. Scrub the surface to be repainted with ne sand paper.

2. Clean it properly.

3. Apply thin coats (2-3) of paint successively.

AIR TUBES

The air tubes assembled in this unit are designed to provide an accurate mix of secondary air to insure the

highest efciency. Any damage or deterioration of these tubes may reduce the efciency of combustion. The

air tubes are held in position by either screws or snap pins. Locate these to either side of the tube and remove to

allow the tube to be removed and replaced.

During the curing process there are changes in the paint causing it to give off an odor and some visible

smoke. The fumes are non-toxic, but can be unpleasant. Ventilate and vacate the room to avoid discomfort.

Once the curing is complete there will be no odor or smoke. After re-coating portions of your stove

remember to follow the curing process as discussed in the rst re section of this manual.

CAUTION: This wood heater needs periodic inspection and repair for proper operation. It is against federal

regulations to operate this wood heater in a manner inconsistent with operating instructions in this manual.

WARNING:

• Never operate the stove without a gasket or with a broken one. Damage to the stove or even house re

may result.

-19-

REPAIR PARTS

Key Part No. Description Qty.

*1 610061 Assy., Door Large Rect. 1

2 891331 Spring Handle - Brushed Nickel 1

3 26333 Cover Plate, Damper 1

4 88189 Gasket, Damper 1

5 69738 Weld., Damper Slide 1

*6 40590 Hearth 1

7 891137 Handle, Brushed Nickel 1

8 69767 Ash Pan Weldment 1

*9 40589 Front 1

*10 40588 Side 2

11 40292A 6” Flue Collar 1

*12 40587 Top 1

13 26934 Air Deector 1

14 891841 Assembly, AFS Blower 1

15 26335 Heat Shield 1

16 69768 Weldment, Ash Pan Housing 1

*17 40566 Leg, Cast Iron 4

When ordering cast-iron repair parts

you must specify the desired color.

Cast Repair Parts Color

Key Description

M Mahogany

R Red

B Black

Note: All parts with (*) beside it requires

a color when ordering repair parts.

-20-

REPAIR PARTS

Key Part No. Description Qty.

1 25465 Retainer, Bottom Glass 2

2 891813 Door Glass (40564) 1

3 88174 Gasket-Flat, Glass Retainer 4 ft

4 88057 1/2 Rope Gasket 5 ft

*5 40639 Door,Rectangular - Large 1

6 892228 7” Handle 1

7 891135 Handle, Spring (Lg-Nickel) 1

When ordering cast-iron repair parts

you must specify the desired color.

Cast Repair Parts Color

Key Description

M Mahogany

R Red

B Black

A Almond

Note: All parts with (*) beside it requires

a color when ordering repair parts.

3 2

In order to maintain warranty, components must be replaced using original manufacturers parts purchased

through your dealer or directly from the appliance manufacturer.

Use of third party components will void the warranty.

Key Part No. Description Qty.

891414A

Half Firebrick 2

2 89066A Firebrick (4-1/2 x 9) 14

3 891783 Firebrick (3 x 4-1/2) 1

4 40561 Ash Plug 1

5 24103A Firebrick, Half (4-1/2 X 4-1/2) 1

6 86645 Tube (Ø7/32), Secondary Air 2

7 86643 Tube (Ø5/32) , Secondary Air 1

8 88146 Board, Ceramic Fiber 1

La page charge ...

Ashley AWC31M Mode d'emploi

Marque: Ashley

Modèle: AWC31M

Catégorie: Poêle à bois

Taper: Mode d'emploi

Ce manuel convient également à

AWC21
AWC31

Télécharger le PDF

rapport

dans d''autres langues

English: Ashley AWC31M User guide

Documents connexes

Ashley Hearth Products AW2020E Manuel utilisateur

Ashley AWC31M Mode d'emploi

Ce manuel convient également à

Ashley AWC31M Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents