Ashley Hearth Products AC1100 Manuel utilisateur

Marque: Ashley Hearth Products

Modèle: AC1100

Catégorie: Poêle à bois

Taper: Manuel utilisateur

SAFETY NOTICE:

If this heater is not properly installed, a house re

may result. For your safety, follow the installation

instructions. Never use make-shift compromises

during the installation of this heater. Contact local

building or re ofcials about permits, restrictions and

installation requirements in your area.

CAUTION!

Please read this entire manual before you install

or use your new room heater. Failure to follow

instructions may result in property damage, bodily

injury, or even death.

Improper Installation Could Void Your Warranty!

SAVE THESE INSTRUCTIONS

THIS MANUAL WILL HELP YOU TO OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM THE HEATER, AND ENABLE YOU

TO ORDER REPAIR PARTS CORRECTLY. KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

French version is available for download from the U.S. Stove website: http://www.usstove.com/

La version française est disponible pour téléchargement à partir du site U.S. Stove: http://www.usstove.com/

Approved for installation in the U.S.A.

CONFORMS TO UL 1482, AND CERTIFIED TO ULC-S627

ALSO SUITABLE FOR MOBILE HOME INSTALLATION.

852263F-2502G

Owner’s Manual MODEL: AC1100

U.S. Stove

227 Industrial Park Road

South Pittsburg, TN 37380

(800) 750-2723 • www.usstove.com

U.S. Environmental Protection Agency

Certied to comply with 2015 particulate emissions standards.

-2-

CAUTIONS:

HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING AND FURNITURE AWAY. CONTACT MAY

CAUSE SKIN BURNS.

DO NOT USE CHEMICALS OR FLUIDS TO IGNITE THE FIRE.

DO NOT LEAVE THE STOVE UNATTENDED WHEN THE DOOR IS SLIGHTLY OPENED.

DO NOT BURN GARBAGE, FLAMMABLE FLUID SUCH AS GASOLINE, NAPHTHA OR MOTOR OIL.

DO NOT CONNECT TO OR USE IN CONJUNCTION WITH ANY AIR DISTRIBUTION DUCTWORK

UNLESS SPECIFICALLY APPROVED FOR SUCH INSTALLATIONS.

ALWAYS CLOSE THE DOOR AFTER THE IGNITION.

CONSULT YOUR MUNICIPAL BUILDING DEPARTMENT OR FIRE OFFICIALS ABOUT PERMITS,

RESTRICTIONS AND INSTALLATIONS REQUIREMENTS IN YOUR AREA.

Combustible: Wood

Colors: Metallic Black

Flue Pipe Diameter: 6” (153cm)

Flue Pipe Type: (Standard Single Wall or Double Wall): Black or Blued Steel 2100°F (650°C)

Minimum Chimney Height: 12’ (3.7m)

Maximum Log Length: 18” (457mm)

Electrical 115V, 60Hz, 1.5A

Dimensions

Overall: Depth x Width x Height: 24” x 29” x 28” (609.6mm x 736.6mm x 711.2mm)

Combustion Chamber:

Width x Depth:

18.3” x 11.5” (465mm x 293mm)

Volume:

Cubic Feet:

1.4 cubic feet

Door Opening: Width x Height: 17” x 8.6” (4.32mm x 2.18mm)

Pyroceramic Glass Door: (Viewing) Width x Height: 16.5” x 10” (419mm x 254mm)

Weight (lbs): 450 lbs

Specications

You’ve purchased a heater from North America’s oldest manufacturer of wood burning products.

By heating with wood you’re helping to CONSERVE ENERGY!

Wood is our only Renewable Energy Resource. Please do your part to preserve our wood supply. Plant at least

one tree each year. Future generations will thank you.

This manual describes the installation and operation of the Ashley, AC1100 wood heater. This heater meets the

2015 U.S. Environmental Protection Agency’s crib wood emission limits for wood heaters sold after May 15, 2015.

Under specic test conditions this heater has been shown to deliver heat at rates ranging from 10,925 to 24,900

Btu/hr.

Note: The BTU ratings mentioned above are based on the EPA test protocol burning dimensional Douglas Fir

lumber. Our advertised BTU’s are based on the rst hour of operation at high burn rate burning cordwood.

-3-

UNPACK AND INSPECT

Remove the packing from the appliance and inspect for any damage. Ensure that the bricks are positioned

correctly and not broken (see illustration for proper brick arrangement). Make sure that the bafe board, above

the air tubes, is in place and undamaged. DO NOT remove the bafe board.

TOOLS AND MATERIALS NEEDED FOR INSTALLATION

A 7/16” socket wrench

A 5/16” socket (Best if using a power drill and a socket bit)

A pair of pliers or channel-locks

A power drill with an 1/8” drill bit to install sheet metal screws into connector pipe.

Sheet metal screws

A non-combustible oor protector as specied in this manual

All chimney and chimney connector components required for your particular venting installation.

PRE-ASSEMBLY

Brick Conguration

ASSEMBLY

ASSEMBLY INSTRUCTIONS

Read and follow the directions in this manual to ensure proper assembly, installation and operation of your new

wood heater.

Caution! The appliance is very heavy.

The assistance from a second person is strongly suggested. Please use proper lifting technic when positioning the

appliance for assembly and installation. Several methods may be used to attach the legs and pedestal to the

appliance. The safest method is to roll the appliance on its back. When using this method, you should rst remove

the rebrick from the unit so as to reduce weight and possible breakage. It will be required to raise the bottom

of the unit up to attach two of the legs. It is recommended that you use cardboard or other means of padding

to protect the nish on your new stove.

FREESTANDING LEG ASSEMBLY

1. Unpack the stove and ensure all components are present:

2. Position the unit for assembly.

3. Make sure that the re brick is in place and undamaged. DO NOT remove the re brick.

-4-

INSTALLATION

POSITIONING THE STOVE

It is very important to position the stove as close as possible to the chimney, and in an area that will favor the

most efcient heat distribution possible throughout the house. The stove must therefore be installed in the room

where the most time is spent, and in the most spacious room possible. Recall that stoves produce radiating

heat, the heat we feel when we are close to a stove. A stove also functions by convection, that is through

the displacement of hot air accelerated upwards and its replacement with cooler air. If necessary, the hot air

distribution from the stove may be facilitated by the use of a fan or blower.

FREE STANDING STOVE INSTALLATION

A stove must never be installed in a hallway or near a staircase, since it may block the way in case of re or fail

to respect required clearances. It is of the utmost importance that the clearances to combustible materials be

strictly adhered to during installation of the stove. Refer to the table and diagrams below for minimum required

clearances.

• Do not place any combustible material within 4’ (1.2m) of the front of the unit.

• The clearance between the ue pipe and a wall are valid only for vertical walls and for vertical ue pipe.

• The chimney connector must not pass through an attic or roof space, closet or similar concealed space, a

oor, or a ceiling.

Back wall / Arrière Mur

Side wall / Paroi Latérale

Back wall / Arrière Mur

Side wall / Paroi Latérale

Back wall / Arrière Mur

Ceiling / Plafond

Floor Protector / Protection de Plancher

M M

Back wall / Arrière Mur

Side wall / Paroi Latérale

Back wall / Arrière Mur

Side wall / Paroi Latérale

Back wall / Arrière Mur

Ceiling / Plafond

Floor Protector / Protection de Plancher

M M

Back wall / Arrière Mur

Side wall / Paroi Latérale

Back wall / Arrière Mur

Side wall / Paroi Latérale

Back wall / Arrière Mur

Ceiling / Plafond

Floor Protector / Protection de Plancher

M M

Dimension Inch mm

A Backwall to Stove 11 280

B Sidewall to Stove 7 178

C Sidewall to Flue 17.3 440

D Wall to Stove (Angled

Installation)

3 77

E Wall to Flue (Angled Installation) 14.4 366

F Ceiling Height 84 2134

G Backwall to Flue 14.8 376

SAFETY NOTICE

• If this stove is not properly installed, a house re may result. To reduce the risk of re, follow the installation

instructions.

• Consult your municipal building department or re ofcials about permits, restrictions and installations

requirements in your area.

• Use smoke detectors in the room where your stove is installed.

• Smoke expelled from the unit, by either paint curing, opening the fuel loading door, or a negative pressure

inside the home, could trigger the smoke detectors. Mount smoke detectors at least 10’ from stove

• Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter uid, or similar liquids to start or

“freshen up” a re in this heater. Keep all such liquids well away from the heater while it is in use.

• In the event of a chimney re, push the air control full closed to deprive the re of oxygen. Call the re

department.

• A source of fresh air into the room or space heated shall be provided when required.

• Room heater, solid fuel type, also for use in mobile homes.

• For Canadian installations, where passage

through a wall, or partition of combustible

construction is desired, the installation must

conform to CAN/CSA-B365.

• A ue pipe crossing a combustible wall

must have a minimum clearance of 18”

(457.2mm).

• To reduce ue clearances from

combustible materials, contact your local

safety department.

-5-

FLOOR PROTECTOR

The stove must be placed on solid concrete, solid masonry, or when installed on a combustible oor, on a oor

protector. The oor protector is required to provide heat, live ember, and ash protection and must be of a non-

combustible, continuous solid surface to protect against inltration of live embers and ash. The stove must be

placed on solid concrete, solid masonry, or when installed on a combustible oor, on a Type 2 oor protector

listed to standard UL 1618 with a minimum R value of 1.03 and a minimum thickness of 1/2” or equivalent.

Dimension Inch mm

H* Front 16 407

J Flue rear 2 51

K** Left 6 204

L** Right 6 204

M Flue Side 2 51

* Canadian installations require 18” (457mm)

** Canadian installations require 8” (203mm)

SPECIAL MOBILE HOME REQUIREMENTS

• WARNING! - Do not install in a sleeping room

• CAUTION! - The structural integrity of the

mobile home oor, wall, and ceiling/roof must be

maintained.

In addition to the previously detailed installation

requirements, mobile home installations must meet the

following requirements:

• The heater must be permanently attached to the

oor.

1. There are two holes in the pedestal base, use

3/8” bolts through the oor.

2. To attach the leg model use two 3/8-16 UNC

bolts through the oor.

• The heater must be electrically grounded to the

steel chassis of the mobile home with 8 GA copper

wire using a serrated or star washer to penetrate

paint or protective coating to ensure grounding.

• When moving your mobile home, all exterior venting

must be removed while the mobile home is being

relocated. After relocation, all venting must be

reinstalled and securely fastened.

• Outside Air is mandatory for mobile home installation.

See your dealer for purchasing.

• Check with your local building ofcials as other

codes may apply.

Mobile Home Attachment

Back wall / Arrière Mur

Side wall / Paroi Latérale

Back wall / Arrière Mur

Side wall / Paroi Latérale

Back wall / Arrière Mur

Ceiling / Plafond

Floor Protector / Protection de Plancher

M M

-6-

COMBUSTION AIR ASSEMBLY INSTRUCTIONS

This appliance requires a source of combustion air. If your home is of tight construction or has negative pressure

problems, you will need an outside source of air. Below is a list of possible indicators that a source of outside

combustion air may be required.

1. Your stove does not draw steadily, smoke rollout occurs, wood burns poorly, or back-drafts occur whether or

not there is combustion present.

2. Existing fuel-red equipment in the house, such as replaces or other heating appliances, smell, do not

operate properly, suffer smoke roll-out when opened, or back-drafts occur whether or not there is combustion

present.

3. Opening a window slightly on a calm (windless) day alleviates any of the above symptoms.

4. The house is equipped with a well-sealed vapor barrier and tight tting windows and/or has any powered

devices that exhaust house air.

5. There is excessive condensation on windows in the winter.

6. A ventilation system is installed in the house.

If an outside air intake is required. You may purchase a standard 4” Dryer Vent kit from your local hardware

supply store. If using a Dryer venting kit, the outlet cover must be of a design that DOES NOT close by means of a

ap or trap door. You must purchase a style that allows a continuous in-ow of air and that has a rodent screen.

DRYER VENTING KIT” INSTALLATION

Follow the manufacturer’s installation instructions for attaching the dryer vent kit to the home. Then attach it to

the appliance.

CHIMNEY

Your wood stove may be hooked up with a factory built or masonry chimney, matching the diameter of the stove

exhaust. If you are using a factory built chimney, it must comply with UL 103 or CSA-B365 standard; therefore it must

be a Type HT (2100°F). It is extremely important that it be installed according to the manufacturer’s specications.

Take into account the chimney’s location to insure it is not too close to neighbors or in a valley which may cause

unhealthy or nuisance conditions.

If you are using a masonry chimney, it is important that it be built in compliance with the specications of the

National Building Code. It must be lined with re clay bricks, metal or clay tiles sealed together with re cement.

(Round ues are the most efcient).

The interior diameter of the chimney ue must be identical to the stove smoke exhaust. A ue which is too small

may cause draft problems, while a large ue favors rapid cooling of the gas, and hence the build-up of creosote

and the risk of chimney res. Note that it is the chimney and not the stove which creates the draft effect; your

stove’s performance is directly dependent on an adequate draft from your chimney.

Do not connect this unit to a chimney ue serving another appliance.

The following recommendations may be useful for the installation of your chimney:

• It must rise above the roof at least 3’ (0.9m) from the uppermost point of contact.

• The exterior portion should be double or triple wall pipe to ensure proper draft.

• The chimney must exceed any part of the building or other obstruction within a 10’ (3.04m) distance by a

height of 2’ (0.6m).

• Installation of an interior chimney is always preferable to an exterior chimney. The interior chimney will

be hotter than an exterior chimney that is being cooled by the ambient air outside the house. Therefore

the gas which circulates will cool

slower, thus reducing the build-

up of creosote and the risk of

chimney res.

• The draft caused by the

tendency for hot air to rise will

be increased with an interior

chimney.

• Using a re screen at the

extremity of the chimney requires

regular inspection in order to

insure that it is not obstructed

thus blocking the draft, and it

should be cleaned when used

regularly.

Ventilation

-7-

MASONRY CHIMNEY

Ensure that a masonry chimney meets the minimum standards of the National Fire Protection Association (NFPA)

by having it inspected by a professional. Make sure there are no cracks, loose mortar or other signs of deterioration

and blockage. Have the chimney cleaned before the stove is installed and operated. When connecting the

stove through a combustible wall to a masonry chimney, special methods are needed as explained in the “5.5

Combustible Wall Chimney Connector Pass-Throughs” Section.

-8-

COMBUSTIBLE WALL CHIMNEY CONNECTOR PASS-THROUGHS

Method A. 12” (304.8 mm) Clearance to Combustible Wall

Member: Using a minimum thickness 3.5” (89 mm) brick and a

5/8” (15.9 mm) minimum wall thickness clay liner, construct a

wall pass-through. The clay liner must conform to ASTM C315

(Standard Specication for Clay Fire Linings) or its equivalent.

Keep a minimum of 12” (304.8 mm) of brick masonry between the

clay liner and wall combustibles. The clay liner shall run from the

brick masonry outer surface to the inner surface of the chimney

ue liner but not past the inner surface. Firmly grout or cement

the clay liner in place to the chimney ue liner.

Method B. 9” (228.6 mm) Clearance to Combustible Wall

Member: Using a 6” (152.4 mm) inside diameter, listed, factory-

built Solid-Pak chimney section with insulation of 1” (25.4 mm) or

more, build a wall pass-through with a minimum 9” (228.6 mm) air

space between the outer wall of the chimney length and wall

combustibles. Use sheet metal supports fastened securely to wall

surfaces on all sides, to maintain the 9” (228.6 mm) air space.

When fastening supports to chimney length, do not penetrate

the chimney liner (the inside wall of the Solid-Pak chimney). The

inner end of the Solid-Pak chimney section shall be ush with the

inside of the masonry chimney ue, and sealed with a non-water

soluble refractory cement. Use this cement to also seal to the

brick masonry penetration.

Method C. 6” (152.4 mm) Clearance to Combustible Wall

Member: Starting with a minimum 24 gauge (.024” [.61 mm]) 6”

(152.4 mm) metal chimney connector, and a minimum 24 gauge

ventilated wall thimble which has two air channels of 1” (25.4 mm)

each, construct a wall pass-through. There shall be a minimum

6” (152.4) mm separation area containing berglass insulation,

from the outer surface of the wall thimble to wall combustibles.

Support the wall thimble, and cover its opening with a 24-gauge

minimum sheet metal support. Maintain the 6” (152.4 mm) space.

There should also be a support sized to t and hold the metal

chimney connector. See that the supports are fastened securely

to wall surfaces on all sides. Make sure fasteners used to secure

the metal chimney connector do not penetrate chimney ue

liner.

Method D. 2” (50.8 mm) Clearance to Combustible Wall

Member: Start with a solid-pak listed factory built chimney section

at least 12” (304 mm) long, with insulation of 1” (25.4 mm) or more,

and an inside diameter of 8” (2 inches [51 mm] larger than the

6” [152.4 mm] chimney connector). Use this as a pass-through for

a minimum 24-gauge single wall steel chimney connector. Keep

solid-pak section concentric with and spaced 1” (25.4 mm) off

the chimney connector by way of sheet metal support plates at

both ends of chimney section. Cover opening with and support

chimney section on both sides with 24 gauge minimum sheet

metal supports. See that the supports are fastened securely to

wall surfaces on all sides. Make sure fasteners used to secure

chimney ue do not penetrate ue liner.

NOTES:

Connectors to a masonry chimney, excepting method B, shall

extend in one continuous section through the wall pass-

through system and the chimney wall, to but not past the

inner ue liner face.

A chimney connector shall not pass through an attic or roof

space, closet or similar concealed space, or a oor, or

ceiling.

-9-

CHIMNEY CONNECTOR (STOVE PIPE)

Your chimney connector and chimney must have the same diameter as the stove outlet. If this is not the case,

we recommend you contact your dealer in order to insure there will be no problem with the draft.

The stove pipe must be made of aluminized or cold roll steel with a minimum thickness of 0.021” or 0.53 mm. It is

strictly forbidden to use galvanized steel.

Your stove pipe should be assembled in such a way that the male section (crimped end) of the pipe faces

down. Attach each of the sections to one another with three equidistant metal screws. Seal the joints with furnace

cement.

The pipe must be short and straight. All sections installed horizontally must slope at least 1/4 inch per foot,

with the upper end of the section toward the chimney. Any installation with a horizontal run of stove pipe must

conform to NFPA 211. You may contact NFPA (National Fire Protection Association) and request the latest edition

of the NFPA Standard 211.

To insure a good draft, the total length of the stove pipe should never exceed 8’ to 10’ (2.4m to 3.04 m). (Except

for cases of vertical installation, cathedral-roof style where the smoke exhaust system can be much longer and

connected without problem to the chimney at the ceiling of the room).

There should never be more than two 90 degrees elbows in the smoke exhaust system.

Installation of a “barometric draft stabilizer” (replace register) on a smoke exhaust system is prohibited.

Furthermore, installation of a draft damper is not recommended. With a controlled combustion wood stoves the

draft is regulated upon intake of the combustion air in the stove and not at the exhaust.

IMPORTANCE OF PROPER DRAFT

Draft is the force which moves air from the appliance up through the chimney. The amount of draft in your

chimney depends on the length of the chimney, local geography, nearby obstructions and other factors. Too

much draft may cause excessive temperatures in the appliance. Inadequate draft may cause backpufng into

the room and ‘plugging’ of the chimney. Inadequate draft will cause the appliance to leak smoke into the room

through appliance and chimney connector joints. An uncontrollable burn or excessive temperature indicates

excessive draft.

Appliance

-10-

FACTORY BUILT CHIMNEY

When a metal prefabricated chimney is used, the manufacturer’s installation instructions must be followed. You

must also purchase (from the same manufacturer) and install the ceiling support package or wall pass-through

and “T” section package, restops (where needed), insulation shield, roof ashing, chimney cap, etc. Maintain

proper clearance to the structure as recommended by the manufacturer. The chimney must be the required

height above the roof or other obstructions for safety and proper draft operation.

-11-

TYPE

WEIGHT

(LBS. CU.

FT., DRY)

PER

CORD

EFFICIENCY

RANKING

SPLITS

MILLIONS

BTU’s/

CORD

Hickory 63 4500 1.0 Well 31.5

White Oak 48 4100 .9 Fair 28.6

Red Oak 46 3900 .8 Fair 27.4

Beech 45 3800 .7 Hard 26.8

Sugar Maple 44 3700 .6 Fair 26.2

Black Oak 43 3700 .6 Fair 25.6

Ash 42 3600 .5 Well 25.0

Yellow Birch 40 3400 .4 Hard 23.8

Red Maple 38 3200 .3 Fair 22.6

Paper Birch 37 3100 .3 Easy 22.1

Elm/Sycamore 34 2900 .2 Very Difcult 20.1

Red Spruce 29 1800 .1 Easy 16.1

WOOD STOVE UTILIZATION

It is EXTREMELY IMPORTANT that you use DRY WOOD only in your wood oven. The wood should have dried for 9

to 15 months, such that the humidity content (in weight) is reduced below 20% of the weight of the log. It is very

important to keep in mind that even if the wood has been cut for one, two or even more years, it is not necessarily

dry, if it has been stored in poor conditions. Under extreme conditions it may rot, instead of drying. This point

cannot be over stressed; the vast majority of the problems related to the operation of a wood oven is caused by

the fact that the wood used was too damp or has dried in poor conditions.

These problems can be:

• Ignition problems

• Creosote build-up causing chimney res

• Low energy yield

• Blackened windows

• Incomplete log combustion

Smaller pieces of wood will dry faster. All logs exceeding 6” in diameter should be split. The wood should not be

stored directly on the ground. Air should circulate through the cord. A 24” to 48” air space should be left between

each row of logs, which should be placed in the sunniest location possible. The upper layer of wood should be

protected from the elements but not the sides.

This heater is designed to burn natural wood only. Higher efciencies and lower emissions generally result when

burning air dried seasoned hardwoods, as compared to softwoods or to green or freshly cut hardwoods.

DO NOT BURN:

(1) Garbage;

(2) Lawn clippings or yard waste;

(3) Materials containing rubber, including tires;

(4) Materials containing plastic;

(5) Waste petroleum products, paints or paint thinners,

or asphalt products;

(6) Materials containing asbestos;

(7) Construction or demolition debris;

(8) Railroad ties or pressure-treated wood;

(9) Manure or animal remains;

(10) Salt water driftwood or other previously salt water

saturated materials;

(11) Unseasoned wood; or

(12) Paper products, cardboard, plywood, or

particleboard. The prohibition against burning these

materials does not prohibit the use of re starters made

from paper, cardboard, saw dust, wax and similar

substances for the purpose of starting a re in an

affected wood heater.

Burning these materials may result in release of toxic fumes or render the heater ineffective and cause smoke.

Dead wood lying on the forest oor should be considered wet, and requires full seasoning time. Standing dead

wood can usually be considered to be about 2/3 seasoned. Splitting and stacking wood before it is stored

accelerates drying time. Storing wood on an elevated surface from the ground and under a cover or covered

area from rain or snow also accelerates drying time. A good indicator if wood is ready to burn is to check the

piece ends. If there are cracks radiating in all directions from the center then the wood should be dry enough

to burn. If your wood sizzles in the re, even though the surface is dry, it may not be fully cured, and should be

seasoned longer

Waste and other ammable materials should not be burned in your oven. Any type of wood may be used in

your oven, but specic varieties have better energy yields than others. Please consult the following table in order

to make the best possible choice.

-12-

TESTING YOUR WOOD

When the oven is thoroughly warmed, place one piece of split wood (about ve inches in diameter) parallel to

the door on the bed of red embers. Keep the air control full open by pulling on it and close the door. If ignition

of the piece is accomplished within 90 seconds from the time if was placed in the oven, your wood is correctly

dried. If ignition takes longer, your wood is damp. If your wood hisses and water or vapor escapes at the ends of

the piece, your wood is soaked or freshly cut. Do not use this wood in your oven. Large amounts of creosote could

be deposited in your chimney, creating potential conditions for a chimney re.

TAMPER WARNING

This wood heater has a manufacturer-set minimum low burn rate that must not be altered. It is against federal

regulations to alter this setting or otherwise operate this wood heater in a manner inconsistent with operating

instructions in this manual.

THE FIRST FIRES

The fresh paint on your stove needs to be cured to preserve its quality. Once the fuel charge is properly ignited,

only burn small res in your stove for the rst four hours of operation. Never open the air control more than

necessary to achieve a medium burn rate. Make sure that there’s enough air circulation while curing the stove.

The odors could be smelled during the 3 or 4 rst res. Never start your stove outside. You will not be able to see

if you are over heating.

The amount of visible smoke being produced can be an effective method of determining how efciently the

combustion process is taking place at the given settings. Visible smoke consist of unburned fuel and moisture

leaving your stove. Learn to adjust the air settings of your specic unit to produce the smallest amount of visible

smoke. Wood that has not been seasoned properly and has a high wood moisture content will produce excess

visible smoke and burn poorly.

CAUTION: Never alter the damper slide or the adjustment range to increase ring for any reason. Doing so

could result in heater damage and will void your warranty.

CAUTIONS:

• Ashes could contain hot embers even after two days without operating the stove.

• The ash pan can become very hot. Wear gloves to prevent injury.

• Never burn the stove with the stove door or ash clean out opening unsealed . This would result in over ring

the stove. Damage to the stove and even house re may result.

Primary Air Settings

(Slide Damper is located in center of stove under hearth plate)

(Damper Adjustment: Pulling out on damper decreases air)

Electric Blower Speed Setting (Variable)

(Blower is on High when turned “ON”, Rotate

clockwise until stop for “LOW”.)

Burn Rate Adjust Damper from fully closed Burn Time Blower Speed

Low Closed @ 30 minutes Low

Medium - Low 5/16” @ 30 minutes Low

Medium - High 9/16” @ 30 minutes Low

High Fully Open all minutes High

IGNITION

After making sure that the stove air intake controls are fully open (completely pull-out towards you), place

several rumpled sheets of paper in the center of the combustion chamber. Place 8 to 10 pieces of small dry

kindling wood over the paper in the form of a tent. You may also place a few pieces of heating wood, but

choose the smaller ones. No chemical product should be used to light the re.

Before igniting the paper and kindling wood, it is recommended that you warm up the chimney. This is done

in order to avoid back draft problems often due to negative pressure in the house. If such is the case, open a

window slightly near the stove and twist together a few sheets of newspaper into a torch. Light up this paper

torch and hold it as close as possible to the mouth of the pipe inside the combustion chamber to warm up

the chimney. Once the updraft movement is initiated, you are ready to ignite the stove by lighting the paper

and kindling wood inside the combustion chamber. When you have achieved a good bed of hot embers, we

recommend the following burn procedures:

-13-

WARNINGS:

• Never overre your stove. If any part of the stove starts to glow red, over ring is happening. Readjust the

air intake control at a lower setting.

• The installation of a log cradle or grates is not recommended in your wood stove. Build re directly on

rebrick.

• Never put wood above the rebrick lining of the rebox.

• Attempts to achieve heat output rates that exceed heater design specications can result in permanent

damage to the heater.

OPERATION

Controlled combustion is the most efcient technique for wood heating because it enables you to select the type

of combustion you want for each given situation. The wood will burn slowly if the wood stove air intake control is

adjusted to reduce the oxygen supply in the combustion chamber to a minimum. On the other hand, wood will

burn quickly if the air control is adjusted to admit a larger quantity of oxygen in the combustion chamber. Refer

to the primary air settings table for damper operation setting. Real operating conditions may give very different

results than those obtained during testing according to the species of wood used, its moisture content, the size

and density of the pieces, the length of the chimney, altitude and outside temperature.

EFFICIENCIES

Efciencies can be based on either the lower heating value (LHV) or the higher heating value (HHV) of the fuel.

The lower heating value is when water leaves the combustion process as a vapor, in the case of woodstoves the

moisture in the wood being burned leaves the stove as a vapor. The higher heating value is when water leaves

the combustion process completely condensed. In the case of woodstoves this would assume the exhaust gases

are room temperature when leaving the system, and therefore calculations using this heating value consider

the heat going up the chimney as lost energy. Therefore, efciency calculated using the lower heating value of

wood will be higher than efciency calculated using the higher heating value. In the United States all woodstove

efciencies should be calculated using the higher heating value.

The best way to achieve optimum efciencies is to learn the burn characteristic of you appliance and burn well-

seasoned wood. Higher burn rates are not always the best heating burn rates; after a good re is established a

lower burn rate may be a better option for efcient heating. A lower burn rate slows the ow of usable heat out

of the home through the chimney, and it also consumes less wood.

The top down method of re building is recommended for this appliance. After making sure that the stove air

intake controls are fully open (completely pull-out towards you), Place the largest pieces of wood on the bottom,

laid in parallel and close together. Smaller pieces are placed in a second layer, crossways to the rst. A third layer

of still smaller pieces is laid crossways to the second, this time with some spaces between. Then a fourth layer of

loose, small kindling and twisted newspaper sheets tops off the pile.

OPERATIONAL TIPS

• Get the appliance hot and establish a good coal bed before adjusting to a low burn rate (this may take 30

minutes or more depending on your wood)

• Use smaller pieces of wood during start-up and a high burn rate to increase the stove temperature

• Be considerate of the environment and only burn dry wood

• Burn small, intense res instead of large, slow burning res when possible

• Learn your appliance’s operating characteristics to obtain optimum performance

• Burning unseasoned wet wood only hurts your stoves efciency and leads to accelerated creosote buildup

in your chimney

-14-

RELOADING

Once you have obtained a good bed of embers, you should reload the unit. In order to do so, open the air

controls to maximum a few seconds prior to opening the stove’s door. Then proceed by opening the door very

slowly; open it one or two inches for 5 to 10 seconds, before opening it completely to increase the draft and thus

eliminate the smoke which is stagnant in a state of slow combustion in the stove. Then bring the red embers to

the front of the stove and reload the unit.

For optimal operation of your wood stove, we recommend you to operate it with a wood load approximately

equivalent to the height of re bricks.

It is important to note that wood combustion consumes ambient oxygen in the room. In the case of negative

pressure, it is a good idea to allow fresh air in the room, either by opening a window slightly or by installing a fresh

air intake system on an outside wall.

Creosote - Formation and Need for Removal when wood is burned slowly, it produces tar and other organic

vapors, which combine with expelled moisture to form creosote. The creosote vapors condense in the relatively

cool chimney ue of a slow-burning re. As a result, creosote residue accumulates on the ue lining. When

ignited, this creosote makes an extremely hot re. The chimney connector and chimney should be inspected

at least once every two months during the heating season to determine if a creosote build-up has occurred. If

creosote has accumulated (3mm or more), it should be removed to reduce the risk of a chimney re.

We strongly recommend that you install a magnetic thermometer on your smoke exhaust pipe, approximately

18” above the stove. This thermometer will indicate the temperature of your gas exhaust fumes within the smoke

exhaust system. The ideal temperature for these gases is somewhere between 275°F and 500°F. Below these

temperatures, the build-up of creosote is promoted. Above 500 degrees, heat is wasted since a too large quantity

is lost into the atmosphere.

• To Prevent Creosote Build Up: Always Burn Dry Wood. This Allows Clean Burns And Higher Chimney

Temperatures, Therefore Less Creosote Deposit.

Leave the air control full open for about 5 min. every time you reload the stove to bring it back to proper

operating temperatures. The secondary combustion can only take place if the rebox is hot enough.

Always check for creosote deposit once every two months and have your chimney cleaned at least once a

year.

If a chimney or creosote re occurs, close all dampers immediately. Wait for the re to go out and the heater to

cool, then inspect the chimney for damage. If no damage results, perform a chimney cleaning to ensure there is

no more creosote deposits remaining in the chimney.

ASH DISPOSAL

Ashes should be removed from the stove every few days or when ashes get to 2 to 3 inches deep. Always

empty the stove when it is cold, such as in the morning. Disposal of Ashes: Ashes should be placed in a metal

container with a tight tting lid. The closed container of ashes should be placed on a noncombustible oor or

on the ground, well away from all combustible materials, pending nal disposal. If the ashes are disposed of by

burial in soil or otherwise locally dispersed, they should be retained in the closed container until all cinders have

thoroughly cooled. Other waste shall not be placed in this container.

SMOKE AND CO MONITORS

Burning wood naturally produces smoke and carbon monoxide(CO) emissions. CO is a poisonous gas when

exposed to elevated concentrations for extended periods of time. While the modern combustion systems in

heaters drastically reduce the amount of CO emitted out the chimney, exposure to the gases in closed or conned

areas can be dangerous. Make sure you stove gaskets and chimney joints are in good working order and sealing

properly to ensure unintended exposure. It is recommended that you use both smoke and CO monitors in areas

having the potential to generate CO.

-15-

Your wood stove is a high efciency stove and therefore requires little maintenance. It is important to perform

a visual inspection of the stove every time it is emptied, in order to insure that no parts have been damaged,

in which case repairs must be performed immediately. Inspect and clean the chimney and connector pipe

periodically for creosote buildup or obstructions.

GLASS

• Inspect and clean the glass regularly in order to detect any cracks. If you spot one, turn the stove off

immediately. Do not abuse the glass door by striking or slamming shut. Do not use the stove if the glass is

broken.

• If the glass on your stove breaks, replace only with the glass supplied from your heater dealer. Never

substitute other materials for the glass.

• To replace the glass, remove the screws retaining the glass mouldings inside the door. Remove the

mouldings and replace the damaged piece with a new one. Perform the procedure backwards after

replacing. When replacing the glass, you should change the glass gasket to make sure you keep it sealed.

• Never wash the glass with a product that may scratch. Use a specialized product, available in the stores

where wood stoves are sold. The glass should be washed only when cold.

GASKETS

It is recommended that you change the door gasket (which makes your stove door air tight) once a year, in

order to insure good control over the combustion, maximum efciency and security. To change the door gasket,

simply remove the damaged one. Carefully clean the available gasket groove, apply a high temperature

silicone sold for this purpose and install the new gasket. You may light up your stove again approximately 24 hours

after having completed this operation. This unit’s door uses a 1/2” diameter rope gasket.

WARNING: Never operate the stove without a gasket or with a broken one. Damage to the stove or even

house re may result.

BLOWER (IF EQUIPPED)

The blower needs to be removed and air blown clean. Make sure the blades do not have build up.

SECONDARY AIR TUBES

The secondary air tubes must be cleaned with a wire brush. If debris remains in holes lightly tap with a wooden

stick to remove.

FIREBRICK

The rebrick should be cleaned and inspected as necessary. Replace any damaged or broken brick.

AIR TUBES

The air tubes assembled in this unit are designed to provide an accurate mix of secondary air to insure the

highest efciency. Any damage or deterioration of these tubes may reduce the efciency of combustion. The

air tubes are held in position by either screws or snap pins. Locate these to either side of the tube and remove to

allow the tube to be removed and replaced.

Maintenance

CAUTION: This wood heater needs periodic inspection and repair for proper operation. It is against federal

regulations to operate this wood heater in a manner inconsistent with operating instructions in this manual.

-16-

PAINT

Remember to only clean your stove with a dry soft cloth that will not harm the stoves nish.

Your stove has two types of coatings that are used in the nal nish; porcelain enamel and high temperature

stove paint.

ENAMEL REPAIR

The porcelain enamel nish will maintain its color and luster for the life of the stove. However, because it is glass

it may chip if hit with a hard or sharp object. If you experience a scratch or chip in the porcelain enamel nish,

specially formulated gloss touch up paint can be used. Contact you stove dealer to request a small bottle of this

touch up paint.

1. Ensure the stove is cool.

Note: The paint may be applied to a warm stove, but the temperature of the section to be painted should be

below the boiling temperature

(200°F) to achieve a smooth nish.

2. The area should be built up with multiple thin coats.

Note: Better results are obtained if the stove is brought up to operational temperatures between coats.

HIGH TEMPERATURE STOVE PAINT REPAIR

If the painted portions of your stove need re coating it is possible to give those pieces a brand new look by

repainting it with a 1200°F heat resistant stove paint.

1. Scrub the surface to be repainted with ne sand paper.

2. Clean it properly.

3. Apply thin coats (2-3) of paint successively.

During the curing process there are changes in the paint causing it to give off an odor and some visible

smoke. The fumes are non-toxic, but can be unpleasant. Ventilate and vacate the room to avoid discomfort.

Once the curing is complete there will be no odor or smoke. After re-coating portions of your stove

remember to follow the curing process as discussed in the rst re section of this manual.

STOVE MORTAR REPAIR

Sometimes after the cement on the outside of the stove dries and hardens, it will develop some cracks. Thermal

expansion, growth and shrinkage of the cast-iron do to changing temperatures, may contribute to cracks or

chips in the mortar. If you desire to make repairs on your stove mortar contact your stove dealer to request

replace mortar to perform the repair.

REPAIR INSTRUCTIONS

1. Remove any loose pieces of mortar.

2. Using masking tape or blue tape, line both sides of each seam.

3. Cut the tip of the mortar tube for a 1/8” to 3/16” bead.

4. Fill any large voids.

5. Run a continuous bead of grout the entire length of the seam.

6. Smooth the bead to the size of llet desired. Smaller is better.

7. Stop and remove any excess before it spreads beyond the tape.

Note: You may have to do this several times before you can run the full length of the seam.

8. Carefully remove the tape.

9. Using a damp (not soaked) small cell sponge or cotton cloth, run the length of the seam to atten the edge

of the mortar and remove any cement that spread beyond the llet.

10. Rinse the sponge or cloth often.

Note: You must get everything off of the enamel before it dries.

The mortar contains sodium silicate that will etch the porcelain nish if not removed promptly.

It is better to remove too much rather than to make the llet too large.

11. Allow the mortar to dry overnight before ring up the stove.

-17-

Troubleshooting

High Fuel Consumption

Possible Cause Possible Remedies (Unplug blower rst if equipped)

Improper regulation of draft or air inlet

Close air inlet control as much as possible to maintain desired heat

output.

Check all gaskets, reinstall if necessary (see maintenance for gasket

replacement procedure).

Improper door tting

Check door gasket, reinstall if necessary (see maintenance for gasket

replacement procedure).

Check door latch adjustment. Readjust if necessary.

Back Pufng

Possible Cause Possible Remedies (Unplug blower rst if equipped)

Gusts of wind Chimney may need wind diverter

2-10-3 rule not properly maintained Raise chimney to appropriate height

Chimney Blockage

Smoke shelf in chimney is lled with creosote, soot and ash

Tree limb or other obstruction too close

Persistent soot, creosote or ash build up in chimney

Possible Cause Possible Remedies (Unplug blower rst if equipped)

Cool exhaust ue gasses Use double or triple wall external chimney

Burning unseasoned / wet wood Use dry, seasoned hardwood

Smoke rolls out when feed or ash doors are opened

Possible Cause Possible Remedies (Unplug blower rst if equipped)

Wind Gusts blowing down the chimney

Smoke shelf in chimney is lled with creosote, soot and ash

Chimney may need wind diverter

Opening heater door too soon

Open air control, crack door for 5-10 seconds before fully opening

door

Low Heat Output

Possible Cause Possible Remedies (Unplug blower rst if equipped)

Obstruction in chimney Check for blockage in chimney, remove if necessary

Improperly sealed venting

Check all gasketing, replace if necessary

Check exhaust venting seals, reseal if necessary

Wet or unseasoned wood being burned Burn dry, seasoned hard wood

Improper wood loading Load wood according to directions under utilization

Poor chimney draft

Improper chimney height or wrong size ue in use

Inspect chimney for soot, creosote and ash buildup, clean if

necessary.

-18-

REPAIR PARTS

Key Part No Description

Qty

1 40619 Top Cast Grate Left 1

2 40620 Top Cast Grate With Flue 1

3 69942 Heatshield Weldment 1

4 40621 Top Cast Grate Right 1

5 891492 Blower Assembly 1

6 83614 15" Threaded Rod 4

7 88147 Bafe Board 1

8 86655 Secondary Air Tube, Rear 1

9 86656 Secondary Air Tubes 2

10 89066 Firebrick (4-1/2 X 9) 6

11 891414 Half Firebrick 4

12 891095 Firebrick (6 X 8-1/4) 3

13 891987 Plastic Knob 3

14 69945 Weldment, Ash Pan 1

15 86668 Damper Rod 1

16 88174 Gasket-Flat 1

In order to maintain warranty, components must be replaced using original manufacturers parts

purchased through your dealer or directly from the appliance manufacturer.

Use of third party components will void the warranty.

-19-

In order to maintain warranty, components must be replaced using original manufacturers parts

purchased through your dealer or directly from the appliance manufacturer.

Use of third party components will void the warranty.

When ordering cast-iron repair parts

you must specify the desired color.

Cast Repair Parts Color

Key Description

M Mahogany

R Red

B Black

A Almond

Key Part No Description Qty

1 40675 Glass Brace 1

2 88087 Fiberglass Gasket 1

3 892342 Door Glass 1

4 88057 1/2” Robe Gasket 3.5’

5 40695 Cast Door W/Webbing 1

6 40626 Door Latch 1

7 892352 Plastic Handle 1

REPAIR PARTS

-20-

Limited Warranty

Plate Steel Heaters

(Inserts, Freestanding, and Pedestal)

The operation of this heater in a manner inconsistent with the owner’s manual will void the warranty and is also against federal regulations.

United States Stove Company warrants to the original purchaser its products against premature failure of any component due to workmanship, quality, or

materials as follows:

TIME PERIOD:

Firebox ...................................................................................................................................... Three Years

Flue Collar - if equipped .............................................................................................................. Three Years

All Doors .................................................................................................................................... Three Years

Firebox Bafﬂ e ................................................................................................................................. One Year

Door Gaskets ................................................................................................................................. One Year

All Electrical Components (Including Blower) - if equipped ................................................................. One Year

Cabinet and Trim ............................................................................................................................ One Year

CLAIM PROCEDURE

Any defects should be reported to United States Stove Company or its dealer and/or distributor giving descriptions and pertinent data, including proof or

purchase which will be returned upon request.

Providing the heater has been installed and used in accordance with the Owners Manual supplied with the heater, United States Stove Company will either:

1) Replace the defective part free of charge

2) Replace the heater free of charge

3) Where the defect is of a cosmetic (non-functional) nature, United States Stove Company will bear reasonable expense to refurbish the heater,

including such items as welding, painting, and incidental labor. A “Reasonable” is deﬁ ned by terms of this warranty as $30.00/hour with full refund for

any purchase of parts.

NOT COVERED

Speciﬁ cally not covered under terms of this limited warranty or any other warranty are problems relating to smoking or creosote. Smoking is attributable

to inadequate draft due to the design or installation of the ﬂ ue system or installation of the heater itself. Creosote formation is largely attributable to

improper operation of the unit and/or draft as mentioned above. Also, not covered are:

1) Removal and re-installation cost.

2) Service calls to diagnose trouble (unless authorized in writing by the manufacturer, distributor, or dealer).

3) Painted surfaces, brass or brass-colored surfaces.

4) Damage or defect caused by improper installation, accidents, misuse, abuse (including overﬁ ring) or alteration.

5) Transportation or shipping costs.

LIMITATIONS AND EXCLUSIONS

1) United States Stove Company shall not be liable for incidental, consequential, special, or contingent damages anyone might suffer as a result of their

breach of this written warranty or any implied warranty.

2) Should the heater be replaced by United States Stove Company “free of charge”, all further warranty obligations are thereby met.

3) Parts and/or service replacements made under the terms of this warranty are warranted only for the remaining period of the original heater warranty.

4) Without speciﬁ c written exclusionary waivers, no one has authority to add to or vary this limited warranty, or to create for United States Stove

Company any further obligation of liability in connection with this heater or any other applicable accessory. Any further warranty implication applicable

to this heater or any applicable accessory is limited in duration to the same time period as the original statement in the above schedule.

YOUR DUTIES

1) This heater, including all applicable accessories, must be installed and operated in accordance with local authorities having jurisdiction and the

instructions furnished with the Owners Manual.

2) You should keep as permanent record your proof of purchase (or canceled check or invoice).

PROBLEM/RESOLUTION

1) As purchaser, you must ﬁ rst contact the dealer and/or distributor from whom you purchased your heater.

2) If within a reasonable period of time you do not receive satisfactory service from the distributor and/or dealer, write or call United States Stove

Company, Customer Service Department, including complete details of the problem and/or problems you are experiencing, details of your installation,

your proof of purchase, and the heater serial number or test agency code number.

WARRANTOR

The warrantor of record is United States Stove Company, PO Box 151, 227 Industrial Park Road, South Pittsburg, Tennessee 37380.

Phone number 800-750-2723

• Web site www.usstove.com

NOTE

This warranty gives you speciﬁ c legal rights; and, you may also have other rights which vary from state to state. Register your product on line at

www.usstove.com. Save your receipt with your records for any claims.

IMPORTANT

We congratulate you on your selection of United States Stove Company and its products. As the oldest solid fuel manufacturer in the United States

(since 1869), the United States Stove Company is very proud of its products, service, employees, and satisﬁ ed customers. We would like to hear