Tripp Lite SRQ42UB Le manuel du propriétaire
- Catégorie
- Racks
- Taper
- Le manuel du propriétaire
Ce manuel convient également à
1
SmartRack
®
Quiet Rack Enclosure
with Sound Suppression
Model: SRQP42UB
Owner’s Manual
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2018 Tripp Lite. All trademarks are the sole property of their respective owners.
Important Safety Instructions 2
Overview 2
Feature Identification 3
Enclosure Installation 4
Preparation 4
Unpacking 4
Placement 5
Leveling 6
Ground Connection 6
Enclosure Configuration 7
Removing Front and Rear Doors 7
Reversing Front Door 7
Removing Side Panels 9
Adjusting Mounting Rails 9
Adjusting PDU Mounting Brackets 10
Combining (Baying) Enclosures 11
Equipment Installation 12
Installing or Removing Cage Nuts 12
Specifications 13
Storage and Service 13
Warranty and Product Registration 13
Español 14
Français 27
PROTECT YOUR INVESTMENT!
Register your product for quicker service and ultimate peace of mind.
You could also win an ISOBAR6ULTRA surge protector—a $100 value!
www.tripplite.com/warranty
2
Important Safety Instructions
SAVE THESE INSTRUCTIONS
All sections of this manual contain instructions and warnings that should be followed during the installation and use of the SmartRack Enclosures described in
this manual. Read all instructions and warnings thoroughly before attempting to move, install or use the SmartRack Enclosures described in this manual.
Failure to comply will create a risk of personal injury and property damage and may invalidate the warranty.
• Keep the enclosure in a controlled indoor environment, away from moisture, temperature extremes, flammable liquids and gasses, conductive contaminants,
dust and direct sunlight.
• Leave adequate space at the front and rear of the enclosure for proper ventilation. Do not block, cover or insert objects into the external ventilation openings
of the enclosure.
• The enclosure is extremely heavy. Use caution when handling the enclosure. Do not attempt to unpack, move or install it unassisted. Use a mechanical
device such as a forklift or pallet jack to move the enclosure in the shipping container.
• Do not place any object on the enclosure, especially containers of liquid, and do not attempt to stack the enclosures.
• Inspect the shipping container and the enclosure for shipping damage. Do not use the enclosure if it is damaged.
• Leave the enclosure in the shipping container until it has been moved as close to the final installation location as possible. The casters are designed for
minor position adjustments within the final installation area only. The casters are not designed for moving the enclosure over longer distances.
• The casters are not designed to provide long-term support for the enclosure after final installation. Use the levelers to provide long-term support.
• Install the enclosure in a structurally sound area with a level floor that is able to bear the weight of the enclosure, all equipment that will be installed in the
enclosure and any other enclosures and/or equipment that will be installed nearby.
• Do not push the enclosure from the side panels to move it. Pushing from the side panels will cause a tipping hazard.
• When rolling the enclosure on its casters, always push it from behind, never pull it toward you.
• A rolling enclosure can cause personal injury and property damage if not properly supervised. If rolling the enclosure down a ramp is required, use extreme
caution. Do not attempt to use ramps that have a slope steeper than 1:12.
• Use caution when cutting packing materials. The enclosure could be scratched, causing damage not covered by the warranty.
• Save all packing materials for later use. Repacking and shipping the enclosure without the original packing materials may cause product damage that will void
the warranty.
• Do not re-ship the enclosure with additional equipment. The combined weight of the enclosure and installed equipment must not exceed the load capacity of
the pallet. Tripp Lite is not responsible for any damage that occurs during re-shipment.
• Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure of the life support
equipment or to significantly affect its safety or effectiveness is not recommended.
Overview
The SRQP42UB 42U SmartRack Quiet Rack Enclosure with Sound Suppression uses foam sound-dampening panels built into its doors, side panels, and top
and bottom panels to reduce external acoustic levels caused by network equipment. A unique passive airflow design maximizes cooling by drawing in cool air
through the front door’s intake, passing it horizontally through the enclosure, and pushing warm air out through the rear door.
SRQP42UB enclosures ship fully assembled for quick and easy deployment. All standard 19-inch rack-mount equipment is compatible with the SRQP42UB.
Other features include quick-release doors and side panels that allow for convenient maintenance, and reversible front and rear doors for easier installation
flexibility. Integrated baying hardware allows for cost-effective, orderly and efficient expansion.
3
Feature Identification
1
Roof Panel with Foam Sound-Dampening Baffles
2
Brush Strip Plate
3
Locking Reversible Rear Door with Foam Sound-Dampening Baffles
4
Locking Side Panels with Foam Sound-Dampening Baffles
5
PDU Brackets
6
Casters
A
and Levelers
B
7
Mounting Rails (Provide horizontal and vertical mounting points for equipment.)
8
Keys (One for the doors and one for the side panels.)
9
Locking Reversible Front Door with Foam Sound-Dampening Baffles
Not Shown: Mounting hardware, documentation, shipping brackets and other shipping materials.
8
1
2
7
7
4
4
4
4
5
9
6
A
A
B
B
3
4
Enclosure Installation
Caution! Read All Instructions and Warnings Before Installation!
WARNING: The rack enclosure is extremely heavy. Do not attempt to unpack, move or install the enclosure without assistance. Until it has
been properly installed and stabilized, the enclosure is prone to tipping and could cause property damage and/or personal injury. Use
extreme caution when handling the enclosure and be sure to follow all handling and installation instructions. Do not attempt to install
equipment without first stabilizing the enclosure.
Preparation
The enclosure must be installed in a structurally sound area with a level floor that is able to bear the weight of the enclosure, all the equipment that will be
installed in the enclosure and any other enclosures and/or equipment that will be installed nearby. Before unpacking the enclosure, you should transport the
shipping container closer to the final installation location to minimize the distance you will need to move the unit after the protective packaging has been
removed. If you plan to store the enclosure for an extended period before installation, follow the instructions in the Storage and Service section.
You need several tools (user-supplied):
• 13 mm Open-end Wrench
• 18 mm Open-end Wrench
• Utility Blade
• Carpenter's Level
• Phillips-head Screwdriver
• 5/32" Allen Wrench
You also need the following hardware (included):
• (60) Phillips-head Mounting Screws (M6 x 5/8")
• (60) Cage Nuts (M6)
• (60) Nylon Cup Washers
Unpacking
NOTE: If the enclosure is an “SP1” model with a shock pallet, follow the special unpacking instructions attached to the shipping container instead
of the unpacking instructions in this section. All warnings still apply.
1
Confirm that the shipping container is upright and stable, then use a utility blade to cut the shrink-
wrap securing the corner protectors. Apply the utility blade directly over the corner protectors to
prevent the utility blade from scratching the enclosure or cutting the heavy protective plastic bag
beneath the shrink-wrap. WARNING: Do not scratch the enclosure or cut the heavy plastic bag
beneath the shrink-wrap. Do not push or pull the enclosure while unpacking.
2
Remove the corner protectors. Save all packing materials (including the pallet) for later use unless
you are certain they will not be required. The packing materials are recyclable.
3
Remove the heavy plastic bag surrounding the enclosure. Examine the enclosure for any damage or
loose parts. Confirm that all parts are present. If anything is missing or damaged, contact Tripp Lite for
assistance. Do not attempt to use the enclosure if it has been damaged.
1
2
3
5
Enclosure Installation
Unpacking (continued)
4
Use a 13 mm open-end wrench to remove the shipping brackets. Be extremely careful, as the
enclosure could shift unexpectedly after bracket removal. Save the brackets and bracket hardware for
later use.
5
Position at least one person at the front of the enclosure and one person at the rear of the
enclosure. Slowly push the enclosure toward the back of the shipping pallet until all four casters go
over the edge of the pallet and touch the floor. WARNING: Use at least one assistant when
removing the enclosure from the pallet. Be extremely careful when moving the enclosure.
Placement
1
Use the casters to move the enclosure for a short distance over a level, smooth, stable surface by
pushing it from the front or rear (not the side panels). Do not attempt to roll the enclosure over long
distances. The enclosure should be moved close to its installation location inside its shipping
container before it is unpacked. (Use a forklift or pallet jack to move the shipping container.)
WARNING: Do not push or pull the enclosure at the side panels or pull the enclosure toward
you.
If required, the enclosure can be lifted by attaching 4 user-supplied M8 diameter eye bolts to the
threaded holes near the upper corners of the enclosure frame. Use steel bolts with an ISO strength rating
of 8.8 or higher. The 4 bolts can support the weight of the enclosure and up to 1000 lb (450 kg) of
installed equipment. WARNING: Only experienced equipment operators should attempt to lift the
enclosure. Use appropriate equipment and follow all applicable safety procedures and
regulations.
4
5
1
6
Enclosure Installation
Leveling
WARNING: Level the enclosure before attempting to install equipment. The casters are not designed to provide long-term support for the
enclosure. Use the levelers to provide long-term support. Install the enclosure in a structurally sound area with a level floor that is able to bear
the weight of the enclosure, all equipment that will be installed in the enclosure and any other enclosures and/or equipment that will be installed
nearby.
Ground Connection
1
After the enclosure has been moved to the installation location, use a carpenter's level to check the
slope of the floor. If the floor slopes more than 1%, choose an alternate installation site.
2
Use an 18 mm open-end wrench to lower each leveler
A
until it reaches the floor. (There are 4
levelers, 2 at the front and 2 at the rear.) Make sure each leveler contacts the floor solidly.
Note: Lower a leveler by turning it clockwise; raise a leveler by turning it counter-clockwise.
3
After lowering each leveler, use the carpenter's level to confirm that the enclosure is level in all
directions. Adjust the levelers as required until the enclosure is level.
4
(Optional) If you wish to provide an additional measure of stability, you can attach the 2 shipping
brackets, using the hardware that attached the enclosure to the shipping pallet. Use a 13 mm open-
end wrench to connect the brackets to the bracket mounting points of the enclosure. Attach the
brackets to secure mounting points in the floor using user-supplied hardware or Tripp Lite's
SRBOLTDOWN Bolt-Down Kit.
All enclosure components are grounded to the enclosure frame. Use the threaded grounding point closest
to the floor (the two upper threads are reserved for door reversal) and an M6 screw (included) to connect
an 8 AWG (3.264 mm) wire to your facility's earth ground connection. WARNING: Attach each
enclosure to earth ground separately. Do not use the enclosure without an earth ground
connection.
EARTH
GROUND
FLOOR
1
2
3
4
A
7
Enclosure Configuration
Removing Front and Rear Doors
WARNING: The enclosure doors are heavy. Do not attempt to remove
doors without assistance.
Removing Door
1
Disconnect the door's ground wire.
2
Open the door until it is perpendicular (90 degrees) to the front of the enclosure.
3
Lift the door from the hinges and remove it from the enclosure.
To Reinstall Door, Reverse Steps 1-3
(Optional) If the enclosure is joined to another enclosure, turn the door back toward the enclosure as you
lift it from the hinges.
Reversing Front Door
WARNING: The enclosure doors are heavy.
Do not attempt to reverse the front door without assistance.
1
Remove the screw connecting the ground wire to the inside of the door.
2
Remove the 2 screws connecting the door handle to the door. Remove the door handle.
90°
1
2
3
1
2
8
Reversing Front Door (continued)
3
Remove the screw and washer from the rear of the door handle and remove the latching mechanism.
Rotate the latch washer counter-clockwise 90 degrees and reverse the latch so it points in the
opposite direction. Use the screw and washer to re-attach the latch to the rear of the door handle.
4
Remove the door by following the steps in the previous section.
5
Remove the door hinges from the enclosure, rotate them 180 degrees and attach them on the
opposite side of the enclosure.
Note: The alternate door hinge attachment points have plastic plugs in the screw holes. Remove the
plugs and insert them in the original door hinge attachment points.
6
Unscrew the 2 hinge mechanisms from the hinge openings inside the door, then reattach each of
them using the set of screw holes immediately opposite their original position.
7
Rotate the door 180 degrees and reinstall it on the enclosure. Remember to connect the ground wire
to the inside of the door, using the attachment point nearest the hinge at the top of the door. The
attachment point is marked with the ground connection symbol: .
8
Reinstall the door handle.
Enclosure Configuration
3
4
5
7
6
8
9
Adding or Removing Side Panels
Removing Side Panel
1
Open the latch by sliding it downward.
2
Tilt the top of the panel away from the enclosure.
Enclosure Configuration
3
Lift the panel away from the brace that supports it.
To Reinstall Side Panel, Reverse Steps 1-3
Adjusting Mounting Rails
WARNING: Do not attempt to adjust rails without assistance. Do not attempt to adjust rails while equipment is installed in the enclosure.
Do not attempt to use rails without screws installed (4 per rail).
The 4 mounting rails are pre-installed to accommodate equipment with a mounting depth of 30 in. (762 mm). Do not adjust the mounting rails unless your
equipment requires a different mounting depth. The front and rear sets of rails can be adjusted independently in ¼-in. (6 mm) increments for mounting depths
between 4 in. (101.6 mm) and 42 in. (1066.8 mm).
1
Each rail is connected to the enclosure with 4 screws - 1 pair at the upper beam
A
and 1 pair at the
lower beam
B
.
2
Remove the screws fastening each of the rear mounting rails to the enclosure. (If adjustment of the
front rails is required, you can also remove the screws from the front rails.)
1
2
3
1 2 3 4 5 6 7 8 9 0 1 0 1 2 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
A
B
1
2
10
Adjusting PDU Mounting Brackets
WARNING: Do not attempt to adjust brackets without assistance. Do not attempt to adjust brackets while equipment is installed in the enclosure.
Do not attempt to use brackets without screws installed (2 per bracket).
The 4 PDU mounting brackets are pre-installed with the rack enclosure. Do not adjust the mounting brackets unless your equipment requires a different
mounting depth. The sets of brackets can be adjusted independently in ¼-in. (6 mm) increments.
Enclosure Configuration
1
Each bracket is connected to the enclosure with 2 screws – 1 pair at the upper beam
A
and 1 pair at
the lower beam
B
.
2
Remove the screws fastening each of the PDU mounting brackets to the enclosure.
3
Slide the PDU mounting brackets to the desired depth and reattach them using the screws you
removed in Step 2. The attachment points are numbered
A
to help you align each pair of brackets at
the same depth.
Adjusting Mounting Rails (continued)
3
Slide the mounting rails to the desired depth and reattach them using the screws you removed in
Step 2. The rail attachment points are numbered
A
to help you align each pair of rails at the same
depth.
9 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 0 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9
1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 8 8 9 0 1 2 3 4 5 6 7 8 9
2
3
3
A
A
A
B
1
11
Enclosure Configuration
Combining (Baying) Enclosures
WARNING: Combining enclosures is not a substitute for stabilizing the enclosures. Each enclosure in a bay of combined enclosures requires the
same stabilizing measures as a stand-alone enclosure.
1
Arrange the enclosures in the correct position for baying.
2
Each enclosure includes 4 baying brackets
A
that correspond to baying connection points
B
on the
adjoining enclosure. The baying connection points already contain screws. Remove the screw from
each baying connection point in the adjoining enclosure.
3
Loosen the screw in each baying bracket and turn each bracket 90 degrees toward the adjoining
enclosure. Align each bracket with the corresponding baying connection point on the adjoining
enclosure.
4
Connect each bracket to the adjoining enclosure using the screws you removed in step 2, but do not
tighten the screws completely. Adjust the position of the enclosures as needed. If you want the
centers of the enclosures to be 24 in. (61 cm) apart [29.9 in. (76 cm) for wide models], use the
outside hole of the bracket
C
. If you want the centers to be 23.6 in. (60 cm) apart [29.5 in.
(75 cm) for wide models], use the middle hole of the bracket
D
. After connecting all brackets and
confirming that the enclosures do not need further adjustment, tighten all screws.
Note: You may wish to remove the doors from the enclosures before combining them. Reinstalling the
doors afterward is optional. Remove the interior side panels before baying enclosures if you wish to
enable access between enclosures.
90°
3
4
2
1
C
D
A
B
12
Equipment Installation
WARNING: Do not install equipment until you have stabilized the enclosure. Install heavier equipment first and install it toward the bottom of the
enclosure. Install equipment starting from the bottom of the enclosure and proceeding toward the top of the enclosure - never the reverse. If
using sliding equipment rails, be careful when extending the rails. Do not extend more than one set of sliding equipment rails at one time. Avoid
extending sliding equipment rails near the top of the enclosure.
Note: The square holes at the middle of each rack unit are numbered and also include a small notch to aid identification. A single rack unit includes the space
occupied by the numbered hole and the holes directly above and below.
Installing or Removing Cage Nuts
WARNING: The flanges of the cage nuts should engage the sides of the square opening in the rail, not the top and bottom. Follow the instructions
in your equipment documentation to ensure proper installation of your equipment.
Installing Cage Nuts
1
Locate the numbered square openings in the mounting rails where you plan to install your equipment.
You will install cage nuts (included) into the square openings in order to provide an attachment point
for the mounting screws (included).
Note: Consult your equipment documentation to determine how many cage nuts will be required and
where they will need to be installed.
2
From the inside of the mounting rail, insert one of the flanges of the cage nut through the square
opening. Press it against the side of the square opening. Each flange should engage one side of the
square opening, not the top or bottom.
3
Compress the cage nut at the sides slightly to allow the remaining flange to fit through the square
opening. When the cage nut is properly installed, both flanges will protrude through the square
opening and will be visible on the outer surface of the mounting rail. Repeat steps 1-3 until all
required cage nuts are installed.
4
After installing the required cage nuts, use the included mounting screws and cup washers to secure
your equipment to the rack rail. Place the cup washers between the screws and the equipment
mounting brackets.
Note: Your equipment may also include mounting hardware. Read the mounting instructions that
came with your equipment before installing your equipment.
To Remove Cage Nuts, Reverse Steps 1-3
Note: You may wish to use a cage nut tool (user-supplied) to aid cage nut installation and removal.
24
25
26
27
28
29
23
22
21
20
19
18
24
25
26
27
28
29
23
22
21
20
19
18
24
24
2
1 Rack Unit
20
19
18
22
21
20
19
18
22
21
20
19
18
22
21
20
19
18
22
21
1
2
3
4
13
Specifications
Load Capacity Unit Dimensions Shipping Dimensions
Model Static Rolling Height Width Depth Weight Height Width Depth Weight
SRQP42UB 2400 lb.
(1088 kg)
2000 lb.
(907 kg)
78.5 in.
(1993 mm)
23.6 in.
(600 mm)
56.3 in.
(1431 mm)
573 lb.
(260 kg)
83.5 in.
(2120 mm)
26 in.
(660 mm)
58.7 in.
(1490 mm)
600 lb.
(272 kg)
Storage and Service
Storage
The enclosure should be stored in a controlled indoor environment, away from moisture, temperature extremes, flammable liquids and gasses, conductive
contaminants, dust and direct sunlight. Store the enclosure in its original shipping container if possible.
Service
Your Tripp Lite product is covered by the warranty described in this manual. A variety of Extended Warranty and On-Site Service Programs are also available from
Tripp Lite. For more information on service, visit www.tripplite.com/support. Before returning your product for service, follow these steps:
1. Review the installation and operation procedures in this manual to ensure that the service problem does not originate from a misreading of the instructions.
2. If the problem continues, do not contact or return the product to the dealer. Instead, visit www.tripplite.com/support.
3. If the problem requires service, visit www.tripplite.com/support and click the Product Returns link. From here you can request a Returned Material
Authorization (RMA) number, which is required for service. This simple on-line form will ask for your unit’s model and serial numbers, along with other general
purchaser information. The RMA number, along with shipping instructions will be emailed to you. Any damages (direct, indirect, special or consequential) to
the product incurred during shipment to Tripp Lite or an authorized Tripp Lite service center is not covered under warranty. Products shipped to Tripp Lite or
an authorized Tripp Lite service center must have transportation charges prepaid. Mark the RMA number on the outside of the package. If the product is
within its warranty period, enclose a copy of your sales receipt. Return the product for service using an insured carrier to the address given to you when you
request the RMA.
Warranty and Product Registration
5-Year Limited Warranty
Seller warrants this product, if used in accordance with all applicable instructions, to be free from original defects in material and workmanship for a period of 5 years from the date of initial purchase. If the product
should prove defective in material or workmanship within that period, Seller will repair or replace the product, in its sole discretion.
THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE, ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY
EXPRESSLY SET FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES, INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION
TO THE WARRANTY PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES. (Some states do not allow limitations on how long an implied
warranty lasts, and some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal
rights, and you may have other rights which vary from jurisdiction to jurisdiction).
WARNING: The individual user should take care to determine prior to use whether this device is suitable, adequate or safe for the use intended. Since individual applications are subject to great variation, the
manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific application.
Product Registration
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You'll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
Regulatory Compliance Identification Numbers
For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The series number can be found on the product nameplate label, along
with all required approval markings and information. When requesting compliance information for this product, always refer to the series number. The series number should not be confused with the marketing name
or model number of the product.
WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing regulations, when customers buy new electrical and electronic equipment from Tripp Lite they are entitled to:
• Send old equipment for recycling on a one-for-one, like-for-like basis (this varies depending on the country)
• Send the new equipment back for recycling when this ultimately becomes waste
Tripp Lite has a policy of continuous improvement. Product specifications are subject to change without notice.
Note on Labeling
This symbol is used on the product: Ground Connection
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
14
Gabinete de Rack SmartRack
®
con Supresión de Sonido
Modelo: SRQP42UB
Manual del Propietario
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2018 Tripp Lite. Todas la marcas registradas son totalmente propiedad de sus respectivos dueños.
Instrucciones de Seguridad Importantes 15
Descripción 15
Identificación de Características 16
Instalación del Estante 17
Preparación 17
Desempaque 17
Colocación 18
Nivelación 19
Conexión a Tierra 19
Configuración del Estante 20
Removiendo las Puertas 20
del Frente y Traseras
Invirtiendo la Puerta Frontal 20
Removiendo los Paneles Laterales 22
Ajustando los Rieles de Montaje 22
Ajuste de los Soportes para Instalación 23
del PDU
Combinando [Baying] Estantes 24
Instalación del Equipo 24
Instalar o Remover las Tuercas de Jaula 25
Especificaciones 26
Almacenaje y Servicio 26
Garantía 26
English 1
Français 27
15
Instrucciones de Seguridad Importantes
CONSERVE ESTAS INSTRUCCIONES
Todas las secciones de este manual contienen instrucciones y advertencias que deberás seguirse durante la instalación y uso de los Estantes SmartRack
descritos en este manual. Lea cuidadosamente todas las instrucciones y advertencias antes de intentar mover, instalar o usar los Bastidores SmartRack
descritos en este manual. No adherirse a las instrucciones y advertencias de este manual crearán un riesgo de lesiones personales y daños a la propiedad y
puede invalidar las garantía.
• Mantenga el estante en un ambiente al interior controlado, lejos de la humedad, temperaturas extremas, líquidos y gases inflamables, contaminantes
conductores, polvo y luz solar directa.
• Deje un espacio adecuado al frente y atrás del estante para una ventilación adecuada. No bloque, cubra o inserte objetos en las aberturas de ventilación
externa del estante.
• El estante es extremadamente pesado. Tenga cuidado cuando maneje el estante. No intente desempacarlo, moverlo o instalarlo sin ayuda. Use algún
dispositivo mecánico como un montacargas o gato para tarima [pallet jack] para mover el estante y el contenedor de embarque.
• No coloque ningún objeto sobre el estante, especialmente envases con líquidos y no intente apilar los estantes.
• Inspeccione el contenedor de embarque y el estante por posibles daños en el envío. No use el estante si está dañado.
• Deje el estante en el contenedor de embarque hasta que haya sido movido tan cerca como sea posible a su ubicación final. Las ruedas están diseñadas
para ajuste de posición menores dentro del área de instalación final únicamente. Las ruedas no están diseñadas para par mover el estante sobre distancias
más largas.
• Las ruedas no están diseñadas para dar soporte por largo tiempo al estante después de la instalación final. Use los niveladores/puntales para dar soporte
por largo tiempo.
• Instale el estante en un área estructuralmente sólida con un piso nivelado que sea capaz de resistir el peso del estante, a todo el equipo que vaya a ser
instalado en el estante y cualquier otro estante y/o equipo que vaya ser instalado cerca.
• No empuje el estante de los paneles laterales para moverlo. Empujándolo de los paneles laterales puede causar una volcadura.
• Cuando mueva el estante sobre sus ruedas siempre empújelo desde atrás, nunca lo jale hacia usted.
• Un estante en movimiento puede ocasionar lesiones personales y daños ala propiedad si nos es supervisado adecuadamente. Si es necesario rodar hacia
abajo por una rampa al estante extreme precauciones. No intente usar rampas que tengan un declive mayor de 1:12.
• Sea precavido cuando corte el material de empaque. El estante se puede rayar causando un daño no cubierto por la garantía.
• Conserve todo el material de empaque para uso posterior. Reempacar y embarcar el estante sin el empaque original puede causar daños al producto que
anularán su garantía.
• No envíe el estante con equipo adicional. El peso combinado del estante y el equipo instalado no debe exceder la capacidad de la tarima. Tripp Lite no es
responsable de ningún daño que ocurra durante el reenvío.
• Use el uso de este equipo en aplicaciones de soporte de vida en donde la falla de este equipo pueda hacer suponer que causará la falla del equipo de
soporte de vida o significativamente afectar su seguridad o efectividad no es recomendado.
Descripción
El Gabinete de Rack SmartRack
®
con Supresión de Sonido SRQP42UB 42U utiliza paneles de espuma para amortiguación de sonido colocados en puertas,
paneles laterales y paneles superior e inferior para reducir los niveles acústicos externos causados por equipos de la red. Un diseño pasivo único de circulación
de aire maximiza el enfriamiento jalando el aire frío a través de la puerta delantera, pasándolo horizontalmente a través del gabinete y empujando el aire
caliente hacia fuera a través de la puerta trasera.
Los gabinetes SRQP42UB se envían completamente ensamblados para una instalación rápida y fácil Todo el equipo estándar para instalación en rack de
19 pulgadas (482.6 mm) es compatible con el SRQP42UB. Otras características incluyen puertas y paneles laterales de liberación rápida que permiten
mantenimiento conveniente y puertas delanteras y traseras reversibles para más fácil flexibilidad de instalación. El hardware integrado para anclar y unir los
gabinetes permite la expansión ordenada, eficiente y rentable.
16
Identificación de Características
1
Panel de techo con aislantes de espuma para amortiguación de sonido
2
Placa de Tiras de Cepillo
3
Puerta Trasera Reversible con Cerradura con Aislantes de Espuma para Amortiguación de Sonido
4
Paneles Laterales con Cerradura con Aislante de Espuma para Amortiguación de Sonidos
5
Soportes para PDU
6
Ruedas
A
y Niveladores
B
7
Rieles de Instalación (Proporcionan puntos de instalación horizontal y vertical para los equipos).
8
Llaves (Una para las puertas y una para los paneles laterales).
9
Puerta Delantera Reversible con Cerradura con Aislantes de Espuma para Amortiguación de Sonido
No se Muestra: Accesorios para montaje, documentación, ménsulas de embarque y otros materiales de embarque.
8
1
2
7
7
4
4
4
4
5
9
6
A
A
B
B
3
17
Instalación del Estante
¡Precaución!
¡Lea Todas las Instrucciones y Advertencias Antes de la Instalación!
ADVERTENCIA: El estante es extremadamente pesado. No trate de desempacar, mover o instalar el estante sin ayuda. Hasta que no haya
sido adecuadamente instalado y estabilizado, el estante está propenso a volcarse y puede causar daños a la propiedad y/o lesiones
personales. Extreme precauciones cuando maneje el estante y asegúrese de seguir todas las instrucciones de manejo e instalación. No
intente instalar equipo sin antes haber estabilizado el estante.
Preparación
El estante debe instalarse en un área estructuralmente sólida con un piso nivelado que sea capaz de resistir el peso del estante, el equipo que será instalado
en el estante y otros estantes y/o equipos instalados en la cercanía. Antes de desempacar el estante, deberá transportar el contendor de embarque cerca de
de la ubicación de la instalación final a fin de minimizar la distancia que necesitará mover la unidad antes que el empaque de protección haya sido removido.
Si piensa almacenar el estante por un periodo prolongado antes de instalarlo, siga las instrucciones indicadas en la sección Almacenaje y Servicio.
Necesitará varias herramientas (suministradas por el usuario):
• Llave de tuercas de boca abierta de 13 mm
• Llave de tuercas de boca abierta de 18 mm
• Navaja/Cutter
• Nivel de Carpintero
• Desatornillador Phillips
• Llave Hexagonal de 5/32"
También necesitará los siguientes accesorios (incluidos):
• (60) Tornillos de montaje Phillips (M6 x 5/8")
• (60) Tuercas de Jaula (M6)
• (60) Rondana/arandela de copa de nylon
Desempaque
NOTA: Si el estante es un modelo "SP1"con shock pallet, siga las instrucciones de desempaque especiales adjuntas al contenedor de empaque en
lugar de las instrucciones de desempaque de esta sección. Todas las advertencias también aplican.
1
Confirme que el contenedor de embarque esta hacia arriba y estable, a continuación utilice una
navaja para cortar la envoltura plástica [shrink wrap] conservando los protectores de las esquinas.
Use la navaja directamente en las esquinas para evitar dañar el estante o cortar la bolsa protectora
de plástico de uso pesado debajo de envoltura plástica. ADVERTENCIA: No raye el estante o corte
la bolsa de plástico de uso pesado debajo de la envoltura plástica. No empuje o jale el
estante mientras lo desempaca.
2
Remueva los protectores de las esquinas. Guarde todo el material de empaque (incluyendo la tarima)
para uso posterior a menos de que tenga la certeza que ya no lo va a necesitar. Los materiales de
empaque son reciclables.
3
Remueva la bolsa de plástico de uso pesado que cubre el estante. Examine el estante buscando
cualquier daño o partes sueltas. Confirme que están todas las partes y piezas. Si cualquier parte está
dañada o falta, comuníquese con Tripp Lite por ayuda. No trate de usar el estante si éste está
dañado.
1
2
3
18
Instalación del Estante
Desempaque (continuación)
4
Use una llave de tuercas de boca abierta de 13 mm para quitar los soportes de embarque. Extreme
precauciones ya que el estante podría moverse inesperadamente después que haya quitado los
soportes. Conserve los soportes de embarque y los tornillos para uso posterior.
5
Coloque al menos una persona al frente del estante y otra en la parte de atrás del estante.
Lentamente empuje el estante hacia atrás de la tarima de embarque hasta que las cuatro ruedas
rebasen totalmente la parte posterior de la tarima y estén el piso. ADVERTENCIA: Use al menos un
ayudante para mover el estante de la tarima. Extreme precauciones cuando mueva el
estante.
Colocación
1
Use las ruedas para mover el estante cortas distancias sobre una superficie nivelada, suave y estable
empujándolo por atrás (no de los paneles laterales). No trate de rodar el estante por largas
distancias. El estante deberá moverse lo más cerca que sea posible al lugar de la ubicación final
dentro del contenedor de embarque antes de desempacarlo. (Use un montacargas o gato para
tarima para mover el contenedor de embarque.) ADVERTENCIA: No empuje o jale el estante de
los paneles laterales o jale el estante hacia usted.
Si es necesario el estante puede ser levantado fijando 4 armellas/cáncamos con diámetro M8,
suministradas por el usuario, a los perforaciones roscadas localizadas cerca de la esquina superior del
marco del estante. Use armellas de acero de resistencia ISO 8.8 ó mayor. Las 4 armellas resisten el
peso del bastidor y hasta 1000 lb (450 kg) de equipo instalado. ADVERTENCIA: Únicamente
operadores de equipo experimentados deben intentar levantar el estante. Use el equipo
apropiado y siga todos los procedimientos y regulaciones de seguridad aplicables.
4
5
1
19
Instalación del Estante
Nivelación
ADVERTENCIA: Nivele el estante antes de intentar instalar el equipo. Las ruedas no están diseñadas para dar soporte por largo tiempo al estante.
Use los niveladores/puntales para dar soporte por largo tiempo. Instale el estante en un área estructuralmente sólida con un piso nivelado que
sea capaz de resistir el peso del estante, a todo el equipo que vaya a ser instalado en el estante y cualquier otro estante y/o equipo que vaya ser
instalado cerca.
Conexión a Tierra
1
Después que el estante haya sido movido al lugar de instalación, use un nivel de carpintero para
revisar la pendiente del piso. Si el piso tiene una pendiente de más de 1% escoja otro lugar para la
instalación.
2
Use una llave de tuercas de boca abierta de 18 mm para bajar cada nivelador/puntal
A
hasta que
toque el piso. (Hay 4 niveladores, 2 al frente y 2 atrás.) Asegúrese que cada nivelador haga contacto
sólido con el piso.
Nota: Baje un nivelador girándolo en el sentido de las manecillas del reloj, elévelo girándolo en
contra del sentido de las manecillas del reloj.
3
Después de bajar cada nivelador, use el nivel de carpintero para confirmar que el estante está
nivelado en todas las direcciones. Ajuste los niveladores hasta que el estante esté nivelado.
4
(Opcional) Si desea proporcionar más medidas de estabilidad, puede fijar los 2 soportes de
embarque, usando los mismos tornillos y arandelas que fijaban el estante a la tarima de embarque.
Use una llave de tuercas de boca abierta de 13 mm para conectar los soportes de embarque a los
puntos de montaje externos
A
o internos
B
del estante. A continuación fije los soportes a los puntos
de anclaje en el piso utilizando tornillos suministrados por el usuario o con el juego SmartRack Bolt-
Down de Tripp Lite (Parte # SR331).
Todos los componentes del gabinete son conectados a tierra en el bastidor del gabinete. Use el punto
roscado de conexión a tierra más cercano al piso (las dos roscas superiores están reservadas para invertir
la puerta) y un tornillo de M6 (incluido) para conectar un cable 8 AWG (3.264 mm) a la conexión de
tierra de tierra de su instalación. ADVERTENCIA: Fije la conexión a tierra de cada estante por
separado. No use el estante sin una adecuada conexión a tierra.
EARTH
GROUND
2
3
4
A
PISO
1
TIERRA
FÍSICA
20
Configuración del Estante
Removiendo las Puertas del Frente y Traseras
ADVERTENCIA: Las puertas del gabinete son pesadas. No intente retirar las puertas sin ayuda.
Removiendo la Puerta
1
Desconecte el cable de conexión a tierra de la puerta.
2
Abra la puerta hasta que este perpendicular (90 grados) al frente del estante.
3
Levante la puerta hasta sacarla de las bisagras y quítela del estante.
Para Reinstalar la Puerta, Revierta los Pasos 1 a 3
(Opcional) Si el estante está unido a otro estante, gire la puerta hacia el estante mientras la saca de sus
bisagras.
Invirtiendo la Puerta Frontal
ADVERTENCIA: Las puertas del gabinete son pesadas. No intente retirar las puertas sin ayuda.
1
Quite el tornillo que conecta el cable de tierra al interior de la puerta.
2
Quite los 2 tornillos que conectan la manija de la puerta a la puerta. Remueva la manija de la
puerta.
90°
1
2
3
1
2
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
Tripp Lite SRQ42UB Le manuel du propriétaire
- Catégorie
- Racks
- Taper
- Le manuel du propriétaire
- Ce manuel convient également à
dans d''autres langues
Documents connexes
-
Tripp Lite SR14UBDP Le manuel du propriétaire
-
-
-
-
-
-
-
-
Tripp Lite SR42UBDPWD Le manuel du propriétaire
-
Tripp Lite SR42UBWDCL Le manuel du propriétaire