Homelite ut80953e Le manuel du propriétaire

Marque: Homelite

Modèle: ut80953e

Catégorie: Nettoyeurs haute pression

Taper: Le manuel du propriétaire

SAVE THIS MANUAL FOR FUTURE REFERENCE

Ce nettoyeur haute pression a été conçu et fabriqué conformément

aux strictes normes de fiabilité, simplicité d’emploi et sécurité

d’utilisation. Correctement entretenu, il vous donnera des années

de fonctionnement robuste et sans problème.

AVERTISSEMENT :

Pour réduire les risques de

blessures, l’utilisateur doit lire et veiller à bien comprendre

le manuel d’utilisation avant d’utiliser ce produit.

Merci de votre achat.

Su lavadora de presión ha sido diseñada y fabricada

de conformidad con las estrictas normas para brindar

fiabilidad, facilidad de uso y seguridad para el operador. Con el

debido cuidado, le brindará muchos años de sólido y eficiente

funcionamiento.

ADVERTENCIA: Para reducir el riesgo de lesiones, el

usuario debe leer y comprender el manual del operador antes

de usar este producto.

Le agradecemos su compra.

CONSERVER CE MANUEL POUR

FUTURE RÉFÉRENCE

GUARDE ESTE MANUAL PARA

FUTURAS CONSULTAS

Your pressure washer has been engineered and manufactured to our high standard for dependability, ease of operation,

and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product.

Thank you for your purchase.

OPERATOR’S

MANUAL

MANUEL D’UTILISATION

MANUAL DEL OPERADOR

2700 PSI PRESSURE WASHER

NETTOYEUR HAUTE PRESSION

DE 2 700 PSI

LAVADORA A PRESIÓN

DE 2 700 PSI

UT80953E

To register your Homelite

product, please visit:

http://register.homelite.com/

Pour enregistrer votre produit de

Homelite, s’il vous plaît la visite :

http://register.homelite.com/

Para registrar su producto de

Homelite, por favor visita:

http://register.homelite.com/

NOTICE AVIS AVISO

Do not use E15 or E85 fuel (or fuel

containing greater than 10% ethanol)

in this product. It is a violation of fed-

eral law and will damage the unit and void your warranty.

Ne pas utiliser d’essence E15 ou E85 (ou un carburant

contenant plus de 10 % d’éthanol) dans ce produit. Une

telle utilisation représente une violation de la loi fédérale et

endommagera l’appareil et annulera la garantie.

No utilice combustibles E15 o E85 (ni combustibles que

contengan más de 10 % de etanol) con este producto. Esto

constituye una violación a la ley federal, dañará la unidad

y anulará la garantía.

See this fold-out section for all of the figures referenced in the operator’s manual.

Consulter l’encart à volets afin d’examiner toutes

les figures mentionnées dans le manuel d’utilisation.

Consulte esta sección desplegable para ver todas las figuras

a las que se hace referencia en el manual del operador.

A - Fuel cap (bouchon de carburant, tapa del

combustible)

B - Fuel tank (réservoir de carburant, tanque de

combustible)

C - Oil cap/dipstick (bouchon/jauge d’huile , tapa

del aceite con varilla de nivel)

D - Detergent injection hose (tuyau pour

l’injection du détergent, manguera de

inyección de detergente)

E - Engine switch (commutateur du moteur,

interruptor del motor)

F - High pressure hose (tuyau haute pression,

manguera de alta presión)

G - Nozzle storage (buses et rangement de buse,

boquillas y compartimientos para boquillas)

H - Handle (poignée, mango)

- Trigger handle (poignée de gâchete, mango

del gatillo)

J - Trigger with lock out (gâchette avec

verouillage, gatillo con seguro)

K - Spray wand (lance de pulvérisation, tubo de

rociado)

L - Muffler (silencieux, silenciador)

Fig. 1a

A - 7/16 in. wrench [clé de 11 mm (7/16 po), llave de 11 mm

(7/16 pulg.)]

Fig. 1

iii

Fig. 3

Fig. 4

Fig. 5

A - Push to insert (capuchon de verrouillage du

manche, tapa de aseguramiento del mango)

Fig. 6

A - Trigger handle (poignée à gâchette,

mango del gatillo)

B - Connector (connecteur, conector)

C - Spray wand (lance de pulvérisation,

tubo de rociado)

A - Axle (essieu, eje)

B - Wheel (disque, rueda)

C - Washer (rondelle, conector)

D - Hitch pin (goupille de sûreté, pasador del

enganche)

A - Collar (collier, casquillo)

B - Inlet coupler (raccord d’entrée, acoplador de

entrada)

C - High pressure hose (tuyau haute pression,

manguera de alta presión)

A - Upper spray wand holder (support de la lance

d’arrosage supérieur, soporte para el tubo

rociador superior)

B - Lock nut (écrou de blocage, tuerca de

seguridad)

C - Hex nut (écrou hexagonal, tuerca hexagonal)

D - Lower spray wand holder (support de la lance

d’arrosage inférieur, soporte para el tubo

inferior)

Fig. 7

A - Threaded outlet (têton fileté, conexión

roscada)

B - Collar (collier, casquillo)

C - High-pressure hose (flexible haute

pression, manguera de alta presión)

A - Water intake (rise d’eau, entrada de agua)

B - Garden hose (tuyau d’arrosage, manguera de

jardín)

Fig. 8

Fig. 2

A - Funnel (entonnoir, embudo)

B - Fuel cap (bouchon du réservoir bouchon du

réservoir, tapa del tanque de combustible)

Fig. 9

Fig. 16

A - Oil cap/dipstick (bouchon / jauge d’huile, tapa

del aceite con varilla de nivel)

B - Funnel (entonnoir, embudo)

Fig. 15

Fig. 10

Fig. 14

A - Trigger (gâchette, gatillo)

B - Slot (fente, ranura)

C - Lock out (bouton de verrouillage, seguro)

A - Choke lever (levier d’étrangleur, palanca del

anegador)

B - OFF (RUN) position [position ARRÊT (RUN),

posición FUNCIONAMIENTO (RUN)]

C - ON (cold start) position [position MARCHE

(démarrage à froid), posición de MARCHA

(arranque en frío)

Fig. 12

A - Fuel valve (robinet de carburant, válvula de

combustible)

B - ON position (marche, encendido)

C - OFF position (arrêt, apagado)

Fig. 11

A - Starter grip and rope (lanceur à rappel,

arrancador retráctil)

B - Engine switch (interrupteur du moteur,

interruptor del motor)

A - Nozzle (embout, boquilla)

B - “Click” (déclic, hasta que trabe)

C - Quick-connect collar (collier de raccord

rapide, casquillo de conexión rápida)

D - Spray wand (lance de pulvérisation, tubo de

rociador)

E - Pull back the quick-connect collar (tirer la

bague à connexion rapide, tire del collar de

conexión rápida)

F - Push the nozzle into place (insérer en place la

buse, introduzca la boquilla en su lugar)

G - Push the collar forward (poussez en avant la

bague, empuje del collar adelante)

Fig. 13

A - Filter cover (couvercle du filtre à air, tapa de la

cámara de ventilación)

B - Foam filter (filtre, filtro)

A - Spark plug wrench (clé à bougie, llave para

bujía)

B - Spark plug cap (creux de la bougie, tapa ce la

bujía)

C - Correct electrode gap (correct l’écartement

des pointes d’électrode, correcta separación

interelectródica)

Fig. 19 Fig. 21

Fig. 22

TO STORE THE MACHINE

REMISAGE DE LA MACHINE

PARA GUARDAR LA MÁQUINA

Fig. 18

TO MOVE THE MACHINE

DÉPLACEMENT DE LA MACHINE

PARA MOVER LA MÁQUINA

Fig. 20

CHANGING LUBRICANT

VIDANGE DE LE LUBRIFIANT

CAMBIO DEL LUBRICANTE

Fig. 17

A - Threaded top (bouchon vissé, parte superior

roscada)

B - Rubber seal (joint de caoutchouc, sello de

goma)

C - Paper seal (sceaux de papier, sello de papel)

D - Water intake (rise d’eau, entrada de agua)

E - Pump outlet (sortie de la pompe, orificio de

descarga de la bomba)

Page 2 — English

 Introduction ......................................................................................................................................................................2

Introduction / Introducción

 Important Safety Instructions ........................................................................................................................................... 3

Instructions importantes concernant la sécurité / Instrucciones importantes de seguridad

 Specific Safety Rules ........................................................................................................................................................ 4

Règles de sécurité particulières / Reglas de seguridad específicas

Symbols ......................................................................................................................................................................... 5-6

Symboles / Símbolos

 Features ............................................................................................................................................................................7

Caractéristiques / Características

 Assembly .......................................................................................................................................................................8-9

Assemblage / Armado

 Operation ................................................................................................................................................................... 10-13

Utilisation / Funcionamiento ......................................................................................................................................................... 10-14

 Maintenance ..............................................................................................................................................................14-16

Entretien / Mantenimiento .............................................................................................................................................................. 15-17

 Troubleshooting .............................................................................................................................................................. 17

Dépannage / Solución de problemas ..................................................................................................................................................18

 Warranty ....................................................................................................................................................................18-20

Garantie / Garantía ......................................................................................................................................................................... 19-21

 Parts Ordering and Service ...............................................................................................................................Back Page

Commande de pièces et réparation / Pedidos de piezas y servicio ......................................................... Page arrière / Pág. posterior

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability

have been given top priority in the design of this product making it easy to maintain and operate.

* * *

Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la

conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à

utiliser et à entretenir.

* * *

Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto

se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.

TABLE OF CONTENTS

TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO

INTRODUCTION

INTRODUCTION / INTRODUCCIÓN

Page 3 — English

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

Read and understand all instructions. Failure to follow

all instructions listed below may result in electric shock,

fire and/or carbon monoxide poisoning which will cause

death or serious personal injury.

READ ALL INSTRUCTIONS

 Know your tool. Read the operator’s manual carefully.

Learn the machine’s applications and limitations as well

as the specific potential hazards related to this tool.

Keep guards in place and in working order. Never

operate the tool with any guard or cover removed. Make

sure all guards are operating properly before each use.

 Remove adjusting keys and wrenches. Form habit of

checking to see that keys and adjusting wrenches are

removed from tool before turning it on.

 To reduce the risk of injury, keep children and visitors

away. All visitors should wear safety glasses and be kept

a safe distance from work area.

Keep the area of operation clear of all persons,

particularly small children, and pets.

Do not start or operate the engine in a confined space,

building, near open windows, or in other unventilated

space where dangerous carbon monoxide fumes can

collect. Carbon monoxide, a colorless, odorless, and

extremely dangerous gas, can cause unconsciousness

or death.

 Use right tool. Don’t force tool or attachment to do a

job it was not designed for. Don’t use it for a purpose not

intended.

 Dress properly. Do not wear loose clothing, gloves,

neckties, or jewelry. They can get caught and draw you

into moving parts. Rubber gloves and nonskid footwear

are recommended when working outdoors. Also wear

protective hair covering to contain long hair.

Do not operate the equipment while barefoot or when

wearing sandals or similar lightweight footwear. Wear

protective footwear that will protect your feet and improve

your footing on slippery surfaces.

Exercise caution to avoid slipping or falling.

 Always wear eye protection with side shields marked

to comply with ANSI Z87.1. Following this rule will

reduce the risk of serious personal injury.

 Don’t overreach or stand on unstable support. Keep

proper footing and balance at all times.

 Use only recommended accessories. The use of

improper accessories may cause risk of injury.

 Follow the maintenance instructions specified in this

manual.

 Check damaged parts. Before further use of the

tool, a

guard or other part that is damaged should be carefully

checked to determine that it will operate properly and

perform its intended function. Check for alignment of

moving parts, binding of moving parts, breakage of parts,

mounting, and any other conditions that may affect its

operation. A guard or other part that is damaged must

be properly repaired or replaced by an authorized service

center to avoid risk of personal injury.

 Never leave tool running unattended. Turn power off.

Don’t leave tool until it comes to a complete stop.

Keep the engine free of grass, leaves, or grease to

reduce the chance of a fire hazard.

 Keep the exhaust pipe free of foreign objects.

Follow manufacturer’s recommendations for safe

loading, unloading, transport, and storage of machine.

 Be thoroughly familiar with controls. Know how to stop

the product and bleed pressure quickly.

 Keep tool dry, clean, and free from oil and grease.

Always use a clean cloth when cleaning. Never use

brake fluids, gasoline, petroleum-based products, or any

solvents to clean tool.

 Stay alert and exercise control. Watch what you are

doing and use common sense. Do not operate tool when

you are tired. Do not rush.

Do not operate the product while under the influence

of drugs, alcohol, or any medication.

Check the work area before each use. Remove all

objects such as rocks, broken glass, nails, wire, or string

which can be thrown or become entangled in the

machine.

Do not use tool if switch does not turn it off. Have

defective switches replaced by an authorized service

center.

Before cleaning, repairing, or inspecting, shut off the

engine and make certain all moving parts have stopped.

Disconnect the spark plug wire, and keep the wire away

from the plug to prevent accidental starting.

 Avoid dangerous environment. Don’t use in damp or

wet locations or expose to rain. Keep work area well

lit.

 Never use in an explosive atmosphere. Normal

sparking of the motor could ignite fumes.

Do not operate while smoking or near an open flame.

Do not operate around dry brush, twigs, cloth rags, or

other flammable materials.

 WARNING: Risk of injection or injury – Do not direct

discharge stream at persons.

Page 4 — English

SPECIFIC SAFETY RULES

 Use caution when positioning the pressure washer for

use. Warm air from the engine could cause discolored

spots on grass.

 Never direct a water stream toward people or pets,

or any electrical device.

Before starting any cleaning operation, close doors

and windows. Clear the area to be cleaned of debris,

toys, outdoor furniture, or other objects that could create

a hazard.

Never pick up or carry a machine while the engine is

running.

 Never start the machine if ice has formed in any part

of the equipment.

 Do not use acids, alkalines, solvents, flammable

material, bleaches, or industrial grade solutions

in this product. These products can cause physical

injuries to the operator and irreversible damage to the

machine.

 Always operate the machine on a level surface. If the

engine is on an incline, it could seize due to improper

lubrication (even at the maximum lubricant level).

 WARNING: High pressure jets can be dangerous

if subject to misuse. The jet must not be directed at

persons, animals, electrical devices, or the machine

itself.

Never attempt to make any adjustments while the

engine (motor) is running (except where specifically

recommended by the manufacturer).

 Protective covers must always cover rotating parts

when the engine is running.

Keep cooling air intake (starter grip and rope area) and

muffler side of the engine at least 3 feet away from build-

ings, obstructions, and other combustible objects.

Keep the engine away from flammables and other

hazardous materials.

Keep away from hot parts. The muffler and other engine

parts become very hot; use caution.

Do not touch the spark plug and ignition cable when

starting and operating the engine.

 Check fuel hoses and joints for looseness and fuel

leakage before each use.

 Check bolts and nuts for looseness before each use.

A loose bolt or nut may cause serious engine problems.

Always refuel outdoors. Never refuel indoors or in a

poorly ventilated area.

Never store the machine with fuel in the fuel tank

inside a building where ignition sources are present,

such as hot water and space heaters, clothes dryers,

and the like.

If the fuel tank has to be drained, do this outdoors.

To reduce the risk of fire and burn injury, handle fuel

with care. It is highly flammable.

Do not smoke while handling fuel.

Add fuel before starting the engine. Never remove the

cap of the fuel tank or add fuel while the engine is running

or when the engine is hot.

Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.

Replace all fuel tank and container caps securely.

Wipe spilled fuel from the unit. Move 30 feet away from

refueling site before starting engine.

If fuel is spilled, do not attempt to start the engine but

move the machine away from the area of spillage and

avoid creating any source of ignition until fuel vapors

have dissipated.

Never attempt to burn off spilled fuel under any

circumstances.

Before storing, allow the engine to cool and drain fuel

from the unit.

Store fuel in a cool, well-ventilated area, safely away

from spark and/or flame-producing equipment.

Store fuel in containers specifically designed for this

purpose.

Empty fuel tank and restrain the unit from moving

before transporting in a vehicle.

When servicing use only identical replacement parts.

Use of any other parts may create a hazard or cause

product damage.

ONLY use cold water.

Make sure minimum clearance of 3 feet is maintained

from combustible materials.

Never spray close to the surface to be cleaned as you

can damage the surface.

After stopping the engine, always pull the trigger on

the trigger handle to relieve stored pressure in the

high pressure hose. Failure to do so could result in seri-

ous personal injury.

Ensure the high pressure hose is properly connected

before using the product.

Save these instructions. Refer to them frequently and

use them to instruct other users. If you loan someone this

tool, loan them these instructions also.

Page 5 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning for safe

operation of this product.

SYMBOL NAME EXPLANATION

Safety Alert Indicates a potential personal injury hazard.

Read Operator’s Manual

To reduce the risk of injury, user must read and understand

operator’s manual before using this product.

Eye Protection

Always wear eye protection with side shields marked to comply

with ANSI Z87.1.

Wet Conditions Alert Do not expose to rain or use in damp locations.

Hot Surface

To reduce the risk of injury or damage, avoid contact with any

hot surface.

Risk of Injections

To reduce the risk of injection or injury, never direct a water

stream towards people or pets or place any body part in the

stream. Leaking hoses and fittings are also capable of causing

injection injury. Do not hold hoses or fittings.

Risk of Explosion

Fuel and its vapors are explosive and can cause severe burns

or death.

Risk of Fire

Fuel and its vapors are extremely flammable and explosive. Fire

can cause severe burns or death.

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER:

Indicates an imminently hazardous situation, which, if not avoided, will result

in death or serious injury.

WARNING:

Indicates a potentially hazardous situation, which, if not avoided, could result

in death or serious injury.

CAUTION:

Indicates a potentially hazardous situation, which, if not avoided, may result in

minor or moderate injury.

NOTICE:

(Without Safety Alert Symbol) Indicates important information not related to an

injury hazard, such as a situation that may result in property damage.

Page 6 — English

SYMBOLS

Some of the following symbols may be used on this product. Please study them and learn their meaning for safe

operation of this product.

SYMBOL NAME EXPLANATION

Toxic Fumes

Gas products emit carbon monoxide, an odorless, colorless,

poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

Kickback

To reduce the risk of injury from kickback, hold the spray wand

securely with both hands when the machine is on.

Electric Shock

Failure to use in dry conditions and to observe safe practices

can result in electric shock.

Chemical Burns

To reduce the risk of injury or damage, DO NOT USE ACIDS,

ALKALINES, BLEACHES, SOLVENTS, FLAMMABLE MATERIAL,

OR INDUSTRIAL GRADE SOLUTIONS in this product.

Page 7 — English

FEATURES

PRODUCT SPECIFICATIONS

Engine................................................................................................................................................................... 179cc OHV

Lubricant Fill Volume .............................................................................................................................Approximately 14 oz.

Replacement Spark Plug .................................................................................................................Torch F6TC or equivalent

Fuel Tank Capacity ..................................................................................................................................................... 0.96 gal

Maximum Pounds Per Square Inch Pressure* .........................................................................................................2,700 psi

Maximum Gallons Per Minute* ...................................................................................................................................2.3 gpm

Maximum Inlet Water Temperature ................................................................................................................................104˚F

*Max. rating determined by PWMA Standard 101, when tested with red nozzle

KNOW YOUR PRESSURE WASHER

See Figure 1.

The safe use of this product requires an understanding of

the information on the tool and in this operator’s manual as

well as a knowledge of the project you are attempting. Before

use of this product, familiarize yourself with all operating

features and safety rules.

179cc OHV ENGINE

This engine enables the pressure washer to achieve

2,700 psi (pounds per square inch) at a rate of 2.3 gpm

(gallons per minute).

AUTOMATIC DETERGENT INJECTION

SYSTEM

Place the detergent injection hose with filter into your desired

pressure washer detergent to apply detergent quickly and

easily to your cleaning project. Use of the soap nozzle will

activate the detergent injector at a 20:1 dilution ratio.

ENGINE SWITCH

The engine switch is used in combination with the starter

grip and rope to start the engine. It is also used to turn the

engine off.

FUEL TANK

This fuel tank has a maximum capacity of 0.96 gal. Use

unleaded automotive gasoline in the engine.

HOSE STORAGE

Once the high pressure hose is rolled, hang it on the hook

located on the side of handle. Use the hook-and-loop strap

to secure in place.

SOAP NOZZLE

The blue soap nozzle is used to apply detergent at low

pressure only.

STARTER GRIP AND ROPE

The starter grip and rope is pulled to start the machine.

THERMAL RELIEF VALVE

This pump feature will prevent water temperatures from

reaching harmful levels by releasing a small amount of

water. Once the water has drained, the thermal relief valve

will reset itself.

TRIGGER HANDLE

The trigger handle has a gripping surface that provides

added control of the spray wand and helps reduce fatigue.

TRIGGER WITH LOCK OUT

Pulling the trigger releases a stream of water for high

pressure cleaning. The lock out provides protection against

unauthorized use.

Page 8 — English

UNPACKING

This product requires assembly.

 Carefully remove the product and any accessories from

the box. Make sure that all items listed in the packing list

are included.

NOTE: This tool is heavy. To avoid back injury, lift with

your legs, not your back, and get help when needed.

WARNING:

Do not use this product if any parts on the Packing List

are already assembled to your product when you unpack

it. Parts on this list are not assembled to the product by

the manufacturer and require customer installation. Use

of a product that may have been improperly assembled

could result in serious personal injury.

 Inspect the tool carefully to make sure no breakage or

damage occurred during shipping.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the tool.

 If any parts are damaged or missing, please call

1-800-242-4672 for assistance.

PACKING LIST

Pressure Washer

25 ft. High Pressure Hose

Trigger Handle

Spray Wand

Quick-connect Nozzles (4)

Upper Spray Wand Holder

Lower Spray Wand Holder

Lock Nut

1/4-20 (7/16 in.) Hex Nut

4-Cycle Engine Lubricant (SAE 30 or SAE 10W30))

Disposable Funnel

Axle (2)

Hitch pins (2)

Wheels (2)

Washers (2)

Handle

Operator’s Manual

WARNING:

If any parts are damaged or missing do not operate this

tool until the parts are replaced. Use of this product with

damaged or missing parts could result in serious personal

injury.

ASSEMBLY

WARNING:

Do not attempt to modify this tool or create accesso-

ries not recommended for use with this tool. Any such

alteration or modification is misuse and could result in a

hazardous condition leading to possible serious personal

injury.

WARNING:

To prevent accidental starting that could cause serious

personal injury, always disconnect the engine spark plug

wire from the spark plug when assembling parts.

TOOLS NEEDED

See Figure 1a.

 11 mm Wrench (7/16 in.)

ATTACHING THE WHEEL ASSEMBLY

See Figure 2.

 Locate the axle, hitch pins, washers, and wheels.

 Slide the axle through the hole in the center of the wheel.

 Slide the washer onto the axle.

 Lift the machine and slide the axle into the wheel mount-

ing hole in the machine base as shown.

 Push the hitch pin into the hole on the end of the axle to

secure the wheel assembly.

NOTE: The hitch pin should be pushed into the axle until

the center of the pin rests on top of the axle.

 Repeat with the second wheel.

INSTALLING THE HANDLE

See Figure 3.

Push and hold the push-pin button on the side of the handle

as you slide the handle onto the frame.

NOTE: Before use, pull the handle up until the lock

button snaps through the locking slots to secure the handle

in place.

INSTALLING THE UPPER AND LOWER

SPRAY WAND HOLDER

See Figure 4.

 Align upper spray wand holder with holes in handle, as

shown.

 Slide long side of spray wand holder through handle and

tighten securely with lock nut.

 Place lower spray wand holder over the holes in the frame

as shown. The loop should be at the top and the long end

should extend through the frame.

 Install 1/4-20 (7/16 in.) hex nut and tighten securely.

Page 9 — English

ASSEMBLY

CONNECTING THE SPRAY WAND TO THE

TRIGGER HANDLE

See Figure 5.

 Place the threaded end of the spray wand in the connector

on the end of the trigger handle.

 Turn the connector clockwise until it stops. This secures

the spray wand in place.

CONNECTING HIGH PRESSURE HOSE TO

TRIGGER HANDLE

See Figure 6.

 Screw the collar on the high pressure hose into the

trigger handle inlet coupler by turning the hose collar

clockwise. Tighten securely.

NOTE: Be careful to avoid cross-threading, which can

cause the trigger handle to leak during use.

 Pull on the hose to be certain it is properly secured.

CONNECTING THE HIGH PRESSURE HOSE

TO THE PUMP

See Figure 7.

 Completely uncoil and straighten the high pressure hose

to prevent kinks.

NOTE: See Using the High Pressure Hose in Operation

for more information about using the high pressure hose.

 Align the collar on the threaded outlet on the pump.

 Insert the hose on the end of the high pressure hose collar

into the threaded outlet.

 Turn the collar clockwise to tighten the hose securely to

the pump.

NOTE: Be careful to avoid cross-threading, which can

cause the hose to leak during use.

 Pull on the hose to be certain it is properly secured.

CONNECTING THE GARDEN HOSE TO THE

PRESSURE WASHER

See Figure 8.

NOTICE:

Always observe all local regulations when connecting

hoses to the water main. Some areas have restrictions

against connecting directly to public drinking water sup-

ply to prevent the feedback of chemicals into the drinking

water supply. Direct connection through a receiver tank

or backflow preventer is usually permitted.

The water supply must come from a water main. NEVER

use hot water or water from pools, lakes, etc. Before

connecting the garden hose to the pressure washer:

 Run water through the hose for 30 seconds to clean any

debris from the hose.

 Inspect the screen in the water intake.

 If the screen is damaged, do not use the machine until

the screen has been replaced.

 If the screen is dirty, clean it before connecting the garden

hose to the machine.

To connect the garden hose to the machine:

 Completely uncoil the garden hose or remove completely

from reel to prevent kinks.

NOTE: There must be a minimum of 10 feet of unre-

stricted hose between the pressure washer intake and

the hose faucet or shut off valve (such as a “Y” shut off

connector).

 With the hose faucet turned completely off, attach the

end of the garden hose to the water intake. Tighten by

hand.

NOTICE:

Do not run the pressure washer pump without water sup-

ply connected and turned on, as this may damage the

high pressure seals and decrease pump life. Completely

unwind the hose from its reel or coil and make sure the

hose is not being restricted by tires, rocks, or any other

objects that may lessen or prevent water flow to the

pressure washer.

DO NOT OVERTILT THE UNIT!

Page 10 — English

OPERATION

WARNING:

Do not allow familiarity with tools to make you care-

less. Remember that a careless fraction of a second is

sufficient to inflict serious injury.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

Do not use any attachments or accessories not recom-

mended by the manufacturer of this tool. The use of

attachments or accessories not recommended can result

in serious personal injury.

WARNING:

Never direct a water stream toward people or pets, or

any electrical device. Failure to heed this warning could

result in serious injury.

NOTICE:

This product is not equipped with a spark arrestor and

cannot be used on U.S. forest lands; in addition, product

users must comply with Federal, State, and local fire pre-

vention regulations. Check with appropriate authorities.

Contact customer service to purchase a spark arrestor.

APPLICATIONS

You may use this tool around the house for cleaning most

small to large horizontal or vertical exterior surfaces, smaller

exterior objects and structures, and outdoor equipment and

tools.* You can:

Clean or remove mold and mildew from weathered decks,

driveways, patios, walkways, sidewalks, etc.

Remove dirt from various exterior vertical surfaces such

as house exteriors, siding, fences, brick, concrete or stone

walls, etc.

Wash boats, outdoor furniture, powered or non-powered

garden equipment, gutters, window screens, grills, play-

ground equipment, etc.

*Always test in an inconspicuous area first.

ADDING/CHECKING ENGINE LUBRICANT

See Figure 9.

NOTE: This machine has been shipped with approximately

2 oz. of lubricant in the engine from testing. You must add

lubricant to the engine before starting it the first time.

NOTICE:

Any attempt to start the engine without adding lubricant

will result in engine failure.

To add engine lubricant:

 Place pressure washer on a flat, level surface. Do not tilt.

 Unscrew the oil cap/dipstick by turning counter-

clockwise.

 Using 4-stroke engine lubricant (SAE 30 or SAE 10W30),

add engine lubricant until the fluid level rises to the

hatched area on the dipstick (14 oz., 4-cycle engine

lubricant provided). Do not overfill.

 Replace the oil cap / dipstick and securely tighten.

To check engine lubricant level:

 Set pressure washer on a flat surface. Do not tilt.

Unscrew the oil cap/dipstick by turning counterclockwise.

 Wipe dipstick clean and re-seat in hole; do not

rethread.

 Remove dipstick again and check lubricant level. Lubricant

level should fall within the hatched area on the dipstick.

 If level is low, add engine lubricant until the fluid level rises

to the upper portion of the hatched area on the dipstick.

 Replace and secure the oil cap/dipstick.

NOTICE:

Do not overfill. Overfilling the crankcase may cause ex-

cessive smoke and engine damage.

OXYGENATED FUELS

NOTICE:

Do not use E15 or E85 fuel (or fuel containing greater

than 10% ethanol) in this product. It is a violation of

federal law and will damage the unit and void your

warranty.

Fuel system damage or performance problems resulting

from the use of an oxygenated fuel containing more than

the percentage of oxygenates stated below are not covered

under warranty.

Ethanol. Gasoline containing up to 10% ethanol by volume

(commonly referred to as E10) is acceptable. E15 and E85

are not.

Page 11 — English

OPERATION

ADDING GASOLINE TO THE FUEL TANK

See Figure 10.

WARNING:

Gasoline and its vapors are highly flammable and

explosive. To prevent serious personal injury and property

damage, handle gasoline with care. Keep away from

ignition sources, handle outdoors only, do not smoke

while adding fuel, and wipe up spills immediately.

When adding gas to the pressure washer, make sure the unit

is sitting on a flat, level surface. If the engine is hot, let the

pressure washer cool before adding gas. ALWAYS fill the

fuel tank outdoors with the machine turned off.

NOTE: This is a 4-cycle engine. DO NOT mix fuel and

lubricant together.

 Mix fuel stabilizer with gasoline according to fuel stabilizer

manufacturer’s directions.

 Before removing the fuel cap, clean the area around it.

Remove the fuel cap.

 Insert a clean funnel into the fuel tank then slowly

pour gasoline into the tank. Fill tank to approximately

1-1/2 in. below the top of the tank neck (this allows for

fuel expansion).

 Replace fuel cap and tighten until the cap “clicks”.

 Clean up any spills before starting the engine.

PUMP LUBRICANT

The pressure washer pump has been filled with sufficient

lubricant at the factory. You do not need to check or add

lubricant to the pump.

STARTING AND STOPPING THE PRESSURE

WASHER

See Figures 11 - 13.

NOTICE:

Do not run the pressure washer pump without water sup-

ply connected and turned on, as this may damage the

high pressure seals and decrease pump life. Completely

unwind the hose from its reel or coil and make sure the

hose is not being restricted by tires, rocks, or any other

objects that may lessen or prevent water flow to the

pressure washer.

Before starting the engine:

Connect all hoses.

NOTE: Make sure the pressure washer’s water intake

screen is in place and unclogged before connecting

garden hose.

Check all fluids (lubricant and gas).

Turn on the garden hose then pull the trigger to

relieve air pressure; hold the trigger until a steady stream

of water appears.

NOTE: Make sure the faucet is turned on fully and that

there are no kinks or leaks in the hose.

To start the engine:

 Turn the fuel valve to the ON position.

 Move the choke lever to the ON (cold start) position.

NOTE: If restarting after a brief stop (i.e., after refueling

or moving), leave the choke lever in the RUN position.

 Put the engine switch in the ON position.

 Pull the starter grip and rope until the engine runs (a

maximum of 6 times).

NOTE: Do not allow the grip to snap back after starting;

return it gently to its original place.

 Allow the engine to run for 5 seconds, then push the

choke lever to the RUN position.

To stop the engine:

 Put the engine switch in the OFF position.

 Pull trigger to release water pressure.

WARNING:

While operating and storing, keep at least 3 feet of clear-

ance on all sides of this product, including overhead. Al-

low a minimum of 30 minutes of “cool down” time before

storage. Keep all body parts, clothing, combustible ma-

terials, and hoses away from the muffler. Heat created by

muffler and exhaust gases could be hot enough to cause

serious burns, ignite combustible objects, and/or damage

high pressure hoses that can result in an injection injury.

USING THE SPRAY WAND TRIGGER

See Figure 14.

For greater control and safety, keep both hands on the

trigger handle at all times.

 Pull back and hold the trigger to operate the pressure

washer.

 Release the trigger to stop the flow of water through the

nozzle.

To engage the lock out:

 Push up on the lock out until it clicks into the slot.

To disengage the lock out:

 Push the lock out down and into its original position.

To use the spray wand, start with the nozzle 1-2 ft. away

from the cleaning surface. Carefully approach the surface

just until the desired level of cleaning is achieved. If the spray

is too close it can damage the cleaning surface.

Page 12 — English

OPERATION

SELECTING THE RIGHT NOZZLE FOR THE

JOB

See Figure 15.

Each of the nozzles has a different spray pattern. Before

starting any cleaning job, determine the best nozzle for the

job. Refer to the Nozzle Selection Guide for more informa-

tion about which nozzle to choose.

WARNING:

NEVER change nozzles without locking the lock out on

the trigger handle and NEVER point the wand at your

face or at others. The quick-connect feature contains

small springs that could eject the nozzle with some force.

Failure to heed this warning could cause personal injury.

To connect a nozzle to the trigger handle:

 Turn off the pressure washer and shut off the water

supply. Pull trigger to release water pressure.

 Engage the lock out on the trigger handle by pushing up

on the lock out until it clicks into the slot.

 Pull back the quick-connect collar.

 Push the nozzle into place in the spray wand.

 Push the collar forward so that the nozzle is secured

properly. Check to see that the nozzle is secure.

To disconnect a nozzle from the trigger handle once the

cleaning job is complete:

Turn off the pressure washer and shut off the water

supply. Pull trigger to release water pressure.

 Engage the lock out on the trigger handle by pushing up

on the lock out until it clicks into the slot.

 Remove the nozzle by placing hand over nozzle then

pulling back the quick-connect collar. Place nozzle in the

nozzle storage area on the top of the spray wand.

USING THE HIGH PRESSURE HOSE

The high pressure hose features an outer covering that pro-

vides strength to the hose. If the outer covering becomes

damaged, the hose must be replaced immediately. Do not

use a high pressure hose if the outer covering is damaged.

To prevent damage to the outer covering:

 Inspectthehosebeforeeveryuse.

 Fully unwrap and straighten hose before use.

 Do not allow the high pressure hose to be kinked.

 Keephoseawayfromhotsurfacesandsharpedges.

ABRASIVE GENTLE

NOZZLE SELECTION GUIDE

HIGH PRESSURE

(NO SOAP WHEN USING THESE NOZZLES)

LOW

PRESSURE

(FOR SOAP OR

GENTLE RINSE)

0º Red

25º Green 40º White Blue Soap Nozzle

Concrete, Brick, Masonry

   

Siding, Gutters, House

  

Fencing, Deck, Patio

  

Lawn Equipment, Boat, RV

  

 Recommended Nozzle  Use With Caution for Certain Applications

Page 13 — English

OPERATION

 Donotpullunitbyhighpressurehose.

 Do not allow hose to be crushed or wrapped around

objects.

WASHING WITH DETERGENT

See Figure 16.

As sold, this unit is designed for use with “downstream” pres-

sure washer detergents. To convert for use with “upstream”

detergents, contact an authorized customer service center

for more information.

USE ONLY DETERGENTS DESIGNED FOR PRESSURE

WASHERS. Do not use household detergents, acids, alka-

lines, bleaches, solvents, flammable material, or industrial

grade solutions which can damage the pump. Many de-

tergents may require mixing prior to use. Prepare cleaning

solution as instructed on the solution bottle. Always test in

an inconspicuous area before beginning.

 Remove the cap from the detergent container and place

the detergent injection hose with filter in the container.

NOTE: The machine setting of this unit is 20:1, which usu-

ally allows the use of 1 gallon pressure washer detergent

without further dilution. Check your detergent instructions

to be sure additional dilution is not necessary.

 Install the blue soap nozzle on the spray wand.

 Squeeze the trigger and wait approximately 5 seconds

for the detergent to appear.

Spray the detergent on a dry surface using long, even,

overlapping strokes. To prevent streaking, do not allow

detergent to dry on the surface.

Before shutting off the engine:

 Place the detergent injection hose in a bucket of clean

water.

 Flush for 1-2 minutes (spray clear water through the spray

wand).

 Shut off the engine.

NOTE: Shutting OFF ( O ) the engine will not relieve pressure

in the system. Pull trigger to release water pressure.

RINSING WITH THE PRESSURE WASHER

Turn off the pressure washer and shut off the water

supply. Pull trigger to release water pressure.

 Engage the lock out on the trigger handle by pushing up

on the lock out until it clicks into the slot.

 Remove the nozzle by placing hand over nozzle then

pulling back the quick-connect collar. Place nozzle in the

nozzle storage area on the machine.

 Select the right nozzle for the job. See the chart on the

previous page for selecting the appropriate nozzle.

 Start at the top of the area to be rinsed and work down,

overlapping the strokes.

USING PUMP PROTECTOR

See Figure 17.

Regular use of a commercially available pump protector

prolongs the life of the pressure washer by removing hard

water mineral deposits, lubricating pump seals and pistons,

and preventing freeze damage. Pump protector should be

added to the unit after every use and before storage. Pump

protector can be purchased at the retailer where you pur-

chased your pressure washer, or by calling customer service.

The instructions below are for G-Protect Pump Protector.

For other brands, follow the instructions provided by the

manufacturer.

 Turn off the pressure washer engine and shut off the water

supply. Pull trigger to release water pressure.

 Disconnect garden hose and high pressure hose.

 Unscrew threaded top from pump protector bottle and

remove paper seal from bottle. Reinstall top on bottle and

tighten securely.

NOTE: The rubber seal should remain inside the threaded

top. If it comes out, be sure to replace before reinstalling

the top.

 Remove bottle cap and attach threaded end of bottle

securely to pressure washer pump water intake.

 Squeeze bottle to inject contents into pump.

 With engine still off, pull starter rope to cycle pump, then

squeeze bottle again to guarantee complete coverage.

 Pump is protected when the protector fluid exits the pump

outlet.

MOVING THE PRESSURE WASHER

See Figure 18.

NOTE: Never lift or carry this product using the moving handle.

 Turn the pressure washer off.

 Tilt the machine toward you slightly until it balances on

the wheels then roll the machine to the desired position.

Do not tilt forward or sideways when moving.

 DO NOT attempt to move the unit by pulling on any of

the hoses.

HIGH ALTITUDE OPERATION

Specific modifications are needed for high-altitude operation

in altitudes greater than 3000 feet above sea level. Please con-

tact your authorized service center for important information

regarding these modifications. Operating this engine without

the proper altitude modification may increase the engine’s

emissions and decrease fuel economy and performance.

Page 14 — English

MAINTENANCE

WARNING:

When servicing, use only identical replacement parts.

Use of any other parts could create a hazard or cause

product damage.

WARNING:

Always wear eye protection with side shields marked to

comply with ANSI Z87.1. Failure to do so could result in

objects being thrown into your eyes resulting in possible

serious injury.

WARNING:

Before inspecting, cleaning or servicing the machine, shut

off engine, wait for all moving parts to stop, and discon-

nect spark plug wire and move it away from spark plug.

Failure to follow these instructions can result in serious

personal injury or property damage.

NOTICE:

This product is not equipped with a spark arrestor and

cannot be used on U.S. forest lands; in addition, product

users must comply with Federal, State, and local fire pre-

vention regulations. Check with appropriate authorities.

Contact customer service to purchase a spark arrestor.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most

plastics are susceptible to damage from various types of

commercial solvents and may be damaged by their use. Use

clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

Do not at any time let brake fluids, gasoline, petroleum-

based products, penetrating oils, etc., come in contact

with plastic parts. Chemicals can damage, weaken or

destroy plastic which could result in serious personal injury.

Only the parts shown on the parts list are intended to be

repaired or replaced by the customer. All other parts should

be replaced at an authorized service center.

Before running the engine, perform the following pre-

operation steps:

Check that all bolts, nuts, etc., are securely tightened.

Make sure the air filter is clean.

Check both the engine lubricant level and the fuel tank

level; refill as needed.

Inspect the work area for hazards.

If there is excessive noise or vibration, stop the unit

immediately.

NOZZLE MAINTENANCE

Excessive pump pressure (a pulsing sensation felt while pull-

ing the trigger) may be the result of a clogged or dirty nozzle.

Turn off the pressure washer and shut off the water

supply. Pull trigger to release water pressure.

Remove the nozzle from the spray wand.

NOTE: Never point the spray wand at your face.

To free any foreign materials clogging or restricting the

nozzle, blow out or remove debris with a straightened

paperclip or with a fine needle.

Using a garden hose, flush debris out of nozzle by back

flushing (running the water through the nozzle backwards

or from the outside to the inside).

Reconnect the nozzle to the spray wand.

Turn on the water supply and start the engine.

CLEANING/REPLACING THE AIR FILTER

See Figure 19.

A dirty air filter will cause starting difficulty, loss of perfor-

mance, and shorten the life span of the engine. Check the

air filter monthly. For best performance, replace the air filter

at least once a year.

The filter cover pivots up and lifts off.

Using a damp cloth, wipe the air filter cover and inner

surface. Take care not to allow dust to enter the carburetor.

Remove the air filter.

Rinse filter with clean water.

Gently squeeze filter until excess water is removed.

Apply a light coat of engine lubricant to the filter, then

squeeze it out.

Reinstall the foam filter.

NOTE: Make sure the filter is seated properly inside the

compartment. Installing the filter incorrectly will allow dirt

to enter the engine, causing rapid engine wear.

Reinstall the filter cover.

CHANGING ENGINE LUBRICANT

See Figure 20.

Shut off the engine.

Clean the area around the oil fill cap/dipstick, then remove

the oil fill cap/dipstick.

To drain lubricant from the oil drain plug:

Disconnect the spark plug wire from the engine.

To drain the lubricant, remove the drain plug from the

bottom of the engine. Drain lubricant into approved con-

tainer.

NOTE: Remove the dipstick to allow lubricant to drain

easier and more quickly.

NOTE: Drain the lubricant while the engine is still warm

but not hot. Warm lubricant will drain quickly and more

completely.

Page 15 — English

MAINTENANCE

WARNING:

Do not change engine lubricant while it is hot. Accidental

contact with hot engine lubricant could result in serious

burns.

Fill with lubricant following the instructions in Adding/

Checking Engine Lubricant earlier in this manual. For

amount of lubricant needed to refill, see Product Specifi-

cations earlier in this manual or the accompanying engine

manual, if applicable.

Before using the pressure washer, check to ensure that

no lubricant is leaking from the engine.

NOTE: Used lubricant should be disposed of at an approved

disposal site. See your local oil retailer for more information.

CHECKING SPARK PLUG

See Figure 21.

Clean the area around the base of the spark plug before

removing to keep dirt and debris out of the engine. Re-

move spark plug.

Clean off carbon deposits on the spark plug electrode

using a plug cleaner or wire brush. Replace the plug if

worn or reuse is questionable. For replacement spark

plug, see Product Specifications earlier in this manual

or the accompanying engine manual, if applicable.

Check electrode gap. The gap should be 0.7 - 0.8 mm

in. Adjust the gap, if necessary, by carefully bending the

ground electrode.

Check the condition of the spark plug gasket.

Reinstall spark plug. Start the spark plug in its threads

by hand and finger-tighten.

Tighten with wrench to compress washer. If spark plug

is new, use 1/2 turn to compress washer appropriate

amount. If reusing old spark plug, use 1/8 to 1/4 turn for

proper washer compression.

NOTE: An improperly tightened spark plug will become

very hot and could damage the engine.

PUMP MAINTENANCE

Routinely make a visual inspection of the pump. If you notice

any leaking of lubricant around the pump seals, take the

pressure washer to an authorized service center for repair.

There are no user serviceable parts to the pressure washer

pump. Any attempt to service or alter the pump may dam-

age the pressure washer and void your product warranty.

STORING THE PRESSURE WASHER

See Figure 22.

NOTE: Regular use of fuel stabilizer and pump protector

will give you better performance of the unit and increase

the life of the pump. See the Replacement Parts List for

available sizes and part numbers of these items and call

customer service to order.

WARNING:

While storing, keep at least 3 feet of clearance on all sides

of this product, including overhead. Allow a minimum

of 30 minutes of “cool down” time before storage. Heat

created by muffler and exhaust gases could be hot

enough to ignite combustible objects.

Store in a dry, covered area where the weather can’t damage it.

It is important to store this product in a frost-free area. Always

empty water from all hoses, the pump, and the detergent

bucket before storing.

Drain the fuel tank completely by running the pressure

washer until the gas runs out. Stored gas can go stale in

30 days.

NOTE: Make sure the water supply is connected and

turned on when allowing the pressure washer engine to

run.

 Make sure the on/off switch and fuel valve are in the OFF

position.

 Disconnect the water connection.

Empty the pump by pulling on the starter grip and rope

about 6 times. This should remove most of the liquid from

the pump.

NOTICE:

The use of a pump protector is strongly recommended

after each use and before storing to prevent cold weather

and seal damage during storage.

Drain the lubricant and replace with fresh, clean lubricant

as described in Changing Engine Lubricant earlier in

this manual.

Disconnect spark plug wire and remove the spark plug.

Pour about a teaspoon of clean, air-cooled, four-cycle

lubricant through the spark plug hole into the combustion

chamber.

Leaving the spark plug out, pull the starter cord two or

three times to coat the inside of the cylinder wall.

Inspect the spark plug and clean or replace, as necessary.

Reinstall the spark plug, but leave the spark plug wire

disconnected.

Clean the air filter.

Extend the starter grip rope to check its condition. If

the rope is frayed, have it replaced immediately by an

authorized service center.

Page 16 — English

MAINTENANCE

PERIODIC MAINTENANCE SCHEDULE TABLE

NOTE: If a separate engine manual is provided for this pressure washer, please follow the maintenance schedule provided

in the engine manual instead of the maintenance information listed below.

Maintenance Items Each Every Every Every Every Every

use 8 hrs. 20 hrs. 50 hrs. 100 hrs. 300 hrs.

Clean engine & check bolts & nuts X X

Check engine lubricant X

Change engine lubricant

Check water inlet filter placement

Add fuel stabilizer X

Add pump protector X

Clean spark plug X

Clean air cleaner X X

Replace air cleaner element X

Clean & adjust spark plug & electrodes X

Replace spark plug X

Remove carbon from cylinder head

Check & adjust valve clearance

Initial lubricant change should be performed after the first 20 hours of operation. Do not pour old lubricant down

sewage drains, into garden soil, or into open streams. Your local zoning or environmental regulations will give you more

detailed instruction on proper disposal.

If water inlet filter is missing or damaged, it must be replaced. See Replacement Parts List for part number to order.

Have performed by your nearest service center

Remove all hoses. Coil the hoses and store as shown.

Do not allow the hose to become kinked.

Pull the handle release knob out and lower the handle to

the down position.

 Store the unit and accessories in an area that does not

reach freezing temperatures. Do not store near furnace or

other sources of heat that could dry out the pump seals.

PREPARING FOR USE AFTER STORAGE

Pull the starter grip and rope three or four times to clean

lubricant from the combustion chamber.

Remove spark plug from the cylinder. Wipe lubricant from

the spark plug and return it to the cylinder.

Reconnect the spark plug wire.

Refuel the machine as described earlier in the operator’s

manual.

La page est en cours de chargement...

Homelite ut80953e Le manuel du propriétaire

Marque: Homelite

Modèle: ut80953e

Catégorie: Nettoyeurs haute pression

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Homelite ut80953e Owner's manual
español: Homelite ut80953e El manual del propietario

Homelite ut80953e Le manuel du propriétaire

Homelite ut80953e Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents