Browan S1 Manuel utilisateur

S1
Marque
Browan
Modèle
S1
Taper
Manuel utilisateur
Browan Communications Inc.
No.15-1, Zhonghua Rd.,
Hsinchu Industrial Park,
Hukou, Hsinchu,
Taiwan, R.O.C. 30352
Tel: +886-3-6006899
Fax: +886-3-5972970
MerryIoT Light S1
User Manual
Document Number BQW_02_XXXXXX
Revision History
Revision Date Description Author
.001 Oct. 21, 2022 First release
GNMS USER GUIDE
Copyright
© 2021 BROWAN COMMUNICATIONS INC.
This document is copyrighted with all rights reserved. No part of this publication may
be reproduced, transmitted, transcribed, stored in a retrieval system, or translated
into any language in any form by any means without the written permission of
BROWAN COMMUNICATIONS INC.
Notice
BROWAN COMMUNICATIONS INC. reserves the right to change specifications
without prior notice.
While the information in this manual has been compiled with great care, it may not
be deemed an assurance of product characteristics. BROWAN COMMUNICATIONS
INC. shall be liable only to the degree specified in the terms of sale and delivery.
The reproduction and distribution of the documentation and software supplied with
this product and the use of its contents is subject to written authorization from
BROWAN COMMUNICATIONS INC.
Trademarks
The product described in this document is a licensed product of BROWAN
COMMUNICATIONS INC..
GNMS USER GUIDE
REVISION HISTORY .............................................................................................................................. 1
COPYRIGHT ........................................................................................................................................... 2
NOTICE ................................................................................................................................................... 2
TRADEMARKS ....................................................................................................................................... 2
CONTENTS ............................................................................................................................................ 3
CHAPTER 1 – INTRODUCTION ............................................................................................................ 5
Purpose and Scope ............................................................................................................................. 5
Product Design .................................................................................................................................... 5
Product Features ................................................................................................................................. 5
Definitions, Acronyms and Abbreviations ............................................................................................ 6
CHAPTER 2 – HARDWARE DETAILS .................................................................................................. 6
LED Indicators .....................................................................................................................................7
I/O Ports .............................................................................................................................................. 8
Back Label ........................................................................................................................................... 9
Package Label ..................................................................................................................................... 10
Package Content ................................................................................................................................. 10
CHAPTER 3 – SYSTEM SPECIFICATION .......................................................................................... 12
Hardware Specification ..................................................................................................................... 12
Software Specification ....................................................................................................................... 13
3.1 Configuration/Performance/Capability ..................................................................................... 13
3.2 Basic Features ......................................................................................................................... 13
Regulatory Specification .................................................................................................................... 14
Reliability Specification ...................................................................................................................... 14
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT ................................ 15
Contents
Pur
p
MerryI
o
Manuf
a
reliabil
i
MerryI
o
hardw
a
advan
c
IoT pr
o
Pro
d
The di
m
x 24 m
input,
f
Pro
d
●
U
p
●
B
u
●
V
a
●
Et
Ch
a
GN
M
p
ose an
d
o
T Lisght
S
a
cturing,
A
i
ty and hig
o
T Lisght
S
a
re, based
c
ed and st
a
o
jects.
d
uct De
s
m
ension o
f
m, and wi
t
f
our LED i
n
d
uct Fe
a
p
to 8 con
c
u
ilt-in 2.4
G
a
rious Inte
r
hernet/Wi
F
a
pter
1
M
S USER
G
d
Scop
e
S
1 is desi
g
A
utomation
h through
p
S
1 is targ
e
on Linux
d
a
ble functi
ign
f
L0001 H
e
t
h one LA
N
n
dicators,
a
a
tures
c
urrent ch
a
G
802.11b/
g
r
net conn
e
F
i Configu
r
1
– In
t
G
UIDE
e
g
ned for e
d
, Blockch
a
p
ut for the
e
ting at AI
o
d
istributio
n
ons for th
e
e
lium Hot
s
N
port, on
e
a
nd one r
e
a
nnels for
L
g
/n Wirele
s
e
ction: Eth
e
r
ation thro
u
t
rodu
c
d
ge comp
u
a
in and et
c
heavy dat
a
o
T applicat
n
. IoT solu
t
e
ir applica
t
s
pot Miner
e
USB port
e
set butto
n
L
transmis
s
s
s LAN, a
n
e
rnet, WiF
u
gh APP
c
tion
u
ting appli
c
c
, to suppo
r
a
processi
ions with
q
t
ion provid
t
ion-centri
c
V1 is with
, One TF
c
n
.
s
ion
n
d Bluetoo
t
i
c
ations in I
o
r
t high per
f
ng deman
d
q
uad A55
c
ers can e
a
c
develop
m
the dimen
c
ard and
1
t
h 5.2
o
T, Smart
f
ormance,
d
.
c
ores, G5
2
a
sily integr
a
m
ent on th
e
sion of 14
0
1
2V1A po
w
high
2
GPU
a
te
e
ir own
0
x 110
w
er
GNMS USER GUIDE
●Support BROWAN OTA
●Externalantennas forWiFi connection
Definitions, Acronyms and Abbreviations
Item Description
ABP Activation by Personalization
OTAA Over-The-Air Activation
TBD To Be Defined
GNMS USER GUIDE
LED Indicators
LED sequence: Power(System), Internet, WiFi, BT.
Four Green, One White
Solid LED is for static status, blanking means system is upgrading or active devices
linked to the corresponding port
Solid On Blinking Off
Power
System(Blue) Power ON Booting/OTA Power Off
Internet(Blue) Internet available Check
Internet RFU
Wireless(Blue) Wireless connected to
root AP RFU Wireless NOT connected to
root AP
Table 1 LED Behaviors
Chapter 2 – Hardware Details
GNMS USER GUIDE
Figure 1 – IO Ports
I/O Ports
Port Coun
t Description
RJ45 1 WAN port of the device
Reset 1
Reset to default (5 seconds to reset settings to
factory default)
USB 1 Power input via USB adaptor(5VDC/2A)
Push Bottom 1 Enable Bluetooth
Figure 2 – IO Ports
GNMS USER GUIDE
Back Label
The marking information is located at the bottom of apparatus.
Figure
3
Pac
k
N
o. It
e
1 P
r
2 L
a
Pac
k
N
o. D
e
GN
M
3
– Back La
b
k
age La
b
e
m
r
oduct BO
X
a
beling
k
age C
o
e
scription
M
S USER
G
b
e
l
b
el
Des
c
X
Gift
Mo
d
o
ntent
G
UIDE
c
ription
Box
d
el/ MAC/
S
S
erial Nu
m
m
ber/ Type Approval
Qua
n
tity
GNMS USER GUIDE
1 MerryIoT Lisght S1 1
2 Power adapter (12V/1A) 1
3 Antenna and Base 1
Hardware Specification
No. Item Description
1 CPU - Rockchip RK3566
-Quad-core Cortex-A55 up to 1.8GHz
2 Memory - DDR3/4 2GB
3 Storage - eMMC 8GB
5 W-Fi radio - 2.4GHz 1Tx/1Rx 802.11 b/g/n
- Built-in antenna
6 BLE radio - 2.4GHz BLE 5.2
- Built-in antenna
7 GPS(Option) - L1:1575.42±1.023MHz
- External RPSMA antenna with active GPS antenna
8 Crypto chip - I2C control
-Microchip ATECC608A/B in SOIC-8 and UDFN-8
9 LAN interface - RJ45 10/100Mbps x 1
10 LEDs - Single colored LED indicator (green) x 4
Power
Status
System
- Wi-Fi
11 Reset Push button (GPIO)
12 SD card - Built-in
13 Internal console - Debug UART on board
- USB OTG
14 Environment - Temp. operating -10°C ~ +50°C ambient
- Storage -20°C ~ +70°C ambient
-Humidity operating 5%RH ~ 95%RH (non-condensed relative
humidity)
-Altitude operating 0 ~ 3000 Meters
15 IP ratings - IP42 (plastic enclosure)
16 Size - 110x110x30 mm
17 Power - 12V/1A DC jack
- Adapter 12V/1A
Note
Chapter 3 – System Specification
Software Specification
3.1 Configuration/Performance/Capability
Req.
#Features Description comment
PR-
0001 Network
Configuration WiFi or Ethernet switch Configuration
PR-
0002 BLE Name MerryIoT Hotspot V1_xxxxxx where the last hex are
the last 6 uppercase hex of the MAC address.
PR-
0003 OTA
•OTA daily check
•Browan OTA
•ALi OTA
•At the same time update the loading problem
PR-
0004 Gateway Config
•Network setting WiFi
oApp cannot skip WiFi
•Configure Helium on boarding
3.2 Basic Features
Req. # Features Description comment
PR-1001 BLE Button Over 6 seconds then trigger BLE provision
PR-1002 LED
5 LEDS
oPower LED
oInternet LED
oWiFi LED
oBT LED
Refer to Table 1 LED Behavior.
PR-1003 Ethernet Ethernet connection
PR-1004 WiFi Station WiFi Station Mode
PR-1005 BLE Configuration through BLE
PR-1006 Debug port UART for debug
PR-1007 OTA OTA agent
PR-1008 SW Monitor Monitor packet forwarder
Monitor Helium Miner
Monitor Gateway Config
PR-1009 HW Watchdog Monitor system
3.3 WAN features
Req.
#Features Description comment
P
R
-
2001 Packet
Forwarder Compatible with Semtech Packet Forwarder
P
R
-
2002 Miner
Application Miner Application
P
R
-
2003 gateway_mfr Swarm key provision
P
R
-
2004 Gateway config WiFi Setting
Helium on boarding
Regulatory Specification
No
. Item Standard
1 FCC/IC
2 NCC TBD
3 CE
EN 300 328 V2.2.2(included EN 62311/EN 50665/EN 50385)
EN 300 220-2 V3.1.1
EN 301 489-1 V2.2.3
EN 301 489-3 V2.1.1
EN 301 489-17 V3.2.4
EN 55032 / EN 55024
EN 62368-1 LVD
4 RCM TBD
Reliability Specification
No. Item Specification
1 MTBF 300,000 @ 40 
Federal Communication Commission Interference
Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from thatto which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
IMPORTANT NOTE:
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
Country Code selection feature to be disabled for products marketed to the US/CANADA
Operation of this device is restricted to indoor use only
Industry Canada statement:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause
undesired operation of the device
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes :
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm between
the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conformeCanadalimites d'exposition auxradiations dansun environnement
non contrôlé. Cet équipement doit êtreinstallé et utilisé àdistance minimum de 20cmentre le
radiateur etvotre corps.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16

Browan S1 Manuel utilisateur

S1
Marque
Browan
Modèle
S1
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents