Hikoki CD1805DB Manuel utilisateur
- Catégorie
- Outils électroportatifs
- Taper
- Manuel utilisateur
Designed for operating in USA & Canada only.
When this product is used in areas other than the USA & Canada,
we cannot guarantee the product quality and performance.
Model
Modèle
Modelo CD 1805DB
Cordless Metal Cutting Saw
Scie à métaux sans fil
Sierra de corte de metal inalámbrica
SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL
WARNING
IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily injury!
This manual contains important information about product safety. Please read and understand
this manual BEFORE operating the power tool. Please keep this manual available for other
users and owners before they use the power tool. This manual should be stored in safe place.
INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI
AVERTISSEMENT
Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner la mort
ou de sérieuses blessures corporelles!
Ce mode d’emploi contient d’importantes informations à propos de la sécurité de ce produit.
Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser l’outil motorisé. Garder ce
mode d’emploi à la disponibilité des autres utilisateurs et propriétaires avant qu’ils utilisent
l’outil motorisé. Ce mode d’emploi doit être conservé dans un endroit sûr.
INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES
ADVERTENCIA
¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede resultar
en lesiones de gravedad o la muerte!
Este manual contiene información importante sobre la seguridad del producto. Lea y
comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde este manual para
que puedan leerlo otras personas antes de utilizar la herramienta eléctrica. Este manual debe
ser guardado en un lugar seguro.
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
2
IMPORTANT SAFETY INSTRUCTIONS
Read and understand all of the safety precautions, warnings and operating instructions in the Instruction Manual before
operating or maintaining this power tool.
Most accidents that result from power tool operation and maintenance are caused by the failure to observe basic safety
rules or precautions. An accident can often be avoided by recognizing a potentially hazardous situation before it occurs,
and by observing appropriate safety procedures.
Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual and in the sections which
contain the operation and maintenance instructions.
Hazards that must be avoided to prevent bodily injury or machine damage are identified by WARNINGS on the power
tool and in this Instruction Manual.
NEVER use this power tool in a manner that has not been specifically recommended by metaboHPT.
MEANINGS OF SIGNAL WORDS
WARNING indicates a potentially hazardous situations which, if ignored, could result in death or serious injury.
CAUTION indicates a potentially hazardous situations which, if not avoided, may result in minor or moderate injury, or
may cause machine damage.
NOTE emphasizes essential information.
SAFETY
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool.
Failure to follow all instructions listed below may
result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future
reference.
The term “power tool” in the warnings refers to your
mains-operated (corded) power tool or battery-
operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust.
Power tools create sparks which may ignite the
dust or fumes.
c) Keep children and bystanders away while
operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet.
Never modify the plug in any way.
Do not use any adapter plugs with earthed
(grounded) power tools.
Unmodified plugs and matching outlets will
reduce risk of electric shock.
b) Avoid body contact with earthed or
grounded surfaces, such as pipes, radiators,
ranges and refrigerators.
There is an increased risk of electric shock if your
body is earthed or grounded.
c) Do not expose power tools to rain or wet
conditions.
Water entering a power tool will increase the risk
of electric shock.
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
3
d) Do not abuse the cord. Never use the cord
for carrying, pulling or unplugging the power
tool.
Keep cord away from heat, oil, sharp edges
or moving parts.
Damaged or entangled cords increase the risk of
electric shock.
e) When operating a power tool outdoors, use
an extension cord suitable for outdoor use.
Use of a cord suitable for outdoor use reduces
the risk of electric shock.
f) If operating a power tool in a damp location
is unavoidable, use a residual current device
(RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired
or under the influence of drugs, alcohol or
medication.
A moment of inattention while operating power
tools may result in serious personal injury.
b) Use personal protective equipment. Always
wear eye protection.
Protective equipment such as a dust mask, non-
skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the
switch is in the off-position before
connecting to power source and/or battery
pack, picking up or carrying the tool.
Carrying power tools with your finger on the
switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before
turning the power tool on.
A wrench or a key left attached to a rotating part
of the power tool may result in personal injury.
e) Do not overreach. Keep proper footing and
balance at all times.
This enables better control of the power tool in
unexpected situations.
f) Dress properly. Do not wear loose clothing
or jewellery. Keep your hair and clothing
away from moving parts.
Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used.
Use of dust collection can reduce dust-related
hazards.
h) Do not let familiarity gained from frequent
use of tools allow you to become
complacent and ignore tool safety principles.
A careless action can cause severe injury within
a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct
power tool for your application.
The correct power tool will do the job better and
safer at the rate for which it was designed.
b) Do not use the power tool if the switch does
not turn it on and off.
Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c) Disconnect the plug from the power source
and/or remove the battery pack, if
detachable, from the power tool before
making any adjustments, changing
accessories, or storing power tools.
Such preventive safety measures reduce the risk
of starting the power tool accidentally.
d) Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool.
Power tools are dangerous in the hands of
untrained users.
e) Maintain power tools and accessories.
Check for misalignment or binding of moving
parts, breakage of parts and any other
condition that may affect the power toolʼs
operation.
If damaged, have the power tool repaired before
use.
Many accidents are caused by poorly maintained
power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are
easier to control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed.
Use of the power tool for operations different
from those intended could result in a hazardous
situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease.
Slippery handles and grasping surfaces do not
allow for safe handling and control of the tool in
unexpected situations.
5) Battery tool use and care
a) Recharge only with the charger specified by
the manufacturer.
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
4
A charger that is suitable for one type of battery
pack may create a risk of fire when used with
another battery pack.
b) Use power tools only with specifically
designated battery packs.
Use of any other battery packs may create a risk
of injury and fire.
c) When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small
metal objects, that can make a connection
from one terminal to another.
Shorting the battery terminals together may
cause burns or a fire.
d) Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help.
Liquid ejected from the battery may cause
irritation or burns.
e) Do not use a battery pack or tool that is
damaged or modified.
Damaged or modified batteries may exhibit
unpredictable behaviour resulting in fire,
explosion or risk of injury.
f) Do not expose a battery pack or tool to fire
or excessive temperature.
Exposure to fire or temperature above 265°F may
cause explosion.
g) Follow all charging instructions and do not
charge the battery pack or tool outside the
temperature range specified in the
instructions.
Charging improperly or at temperatures outside
the specified range may damage the battery and
increase the risk of fire.
6) Service
a) Have your power tool serviced by a qualified
repair person using only identical
replacement parts.
This will ensure that the safety of the power tool
is maintained.
b) Never service damaged battery packs.
Service of battery packs should only be
performed by the manufacturer or authorized
service providers.
WARNING
To reduce the risk of injury, user must read
instruction manual.
CORDLESS METAL CUTTING SAW
SAFETY WARNINGS
Cutting procedures
1. DANGER: Keep hands away from cutting area
and the blade. Keep your second hand on
auxiliary handle, or motor housing.
If both hands are holding the saw, they cannot be cut
by the blade.
2. Do not reach underneath the workpiece.
The guard cannot protect you from the blade below
the workpiece.
3. Adjust the cutting depth to the thickness of the
workpiece.
Less than a full tooth of the blade teeth should be
visible below the workpiece.
4. Never hold the workpiece in your hands or
across your leg while cutting. Secure the
workpiece to a stable platform.
It is important to support the work properly to
minimise body exposure, blade binding, or loss of
control.
5. Hold the power tool by insulated gripping
surfaces, when performing an operation where
the cutting tool may contact hidden wiring.
Contact with a “live” wire will also make exposed
metal parts of the power tool “live” and could give the
operator an electric shock.
6. When ripping, always use a rip fence or straight
edge guide.
This improves the accuracy of cut and reduces the
chance of blade binding.
7. Always use blades with correct size and shape
(diamond versus round) of arbour holes.
Blades that do not match the mounting hardware of
the saw will run off-centre, causing loss of control.
8. Never use damaged or incorrect blade washers
or bolt.
The blade washers and bolt were specially designed
for your saw, for optimum performance and safety of
operation.
Kickback causes and related warnings
–
kickback is a sudden reaction to a pinched, jammed
or misaligned saw blade, causing an uncontrolled
saw to lift up and out of the workpiece toward the
operator;
–
when the blade is pinched or jammed tightly by the
kerf closing down, the blade stalls and the motor
reaction drives the unit rapidly back toward the
operator;
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
5
–
if the blade becomes twisted or misaligned in the cut,
the teeth at the back edge of the blade can dig into
the top surface of the steel materials causing the
blade to climb out of the kerf and jump back toward
the operator.
Kickback is the result of saw misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below.
1. Maintain a firm grip with both hands on the saw
and position your arms to resist kickback forces.
Position your body to either side of the blade,
but not in line with the blade.
Kickback could cause the saw to jump backwards,
but kickback forces can be controlled by the operator,
if proper precautions are taken.
2. When blade is binding, or when interrupting a
cut for any reason, release the trigger and hold
the saw motionless in the material until the blade
comes to a complete stop.
Never attempt to remove the saw from the work
or pull the saw backward while the blade is in
motion or kickback may occur.
Investigate and take corrective actions to eliminate
the cause of blade binding.
3. When restarting a saw in the workpiece, centre
the saw blade in the kerf so that the saw teeth
are not engaged into the material.
If a saw blade binds, it may walk up or kickback from
the workpiece as the saw is restarted.
4. Support large panels to minimise the risk of
blade pinching and kickback.
Large panels tend to sag under their own weight.
Supports must be placed under the panel on both
sides, near the line of cut and near the edge of the
panel.
5. Do not use dull or damaged blades.
Unsharpened or improperly set blades produce
narrow kerf causing excessive friction, blade binding
and kickback.
6. Blade depth and bevel adjusting locking levers
must be tight and secure before making the cut.
If blade adjustment shifts while cutting, it may cause
binding and kickback.
7. Use extra caution when sawing into existing
walls or other blind areas.
The protruding blade may cut objects that can cause
kickback.
Lower guard function
1. Check the lower guard for proper closing before
each use. Do not operate the saw if the lower
guard does not move freely and close instantly.
Never clamp or tie the lower guard into the open
position.
If the saw is accidentally dropped, the lower guard
may be bent.
Raise the lower guard with the retracting handle and
make sure it moves freely and does not touch the
blade or any other part, in all angles and depths of
cut.
2. Check the operation of the lower guard spring. If
the guard and the spring are not operating
properly, they must be serviced before use.
Lower guard may operate sluggishly due to damaged
parts, gummy deposits, or a build-up of debris.
3. The lower guard may be retracted manually only
for special cuts such as “plunge cuts” and
“compound cuts”.
Raise the lower guard by the retracting handle
and as soon as the blade enters the material, the
lower guard must be released.
For all other sawing, the lower guard should operate
automatically.
4. Always observe that the lower guard is covering
the blade before placing the saw down on bench
or floor.
An unprotected, coasting blade will cause the saw to
walk backwards, cutting whatever is in its path.
Be aware of the time it takes for the blade to stop after
switch is released.
SPECIFIC SAFETY RULES AND SYMBOLS
1. Adjustments. Before cutting be sure cutting
depth adjustment is tight.
2. Avoid cutting nails. Inspect for and remove all
nails from work piece before cutting.
3. When operating the saw, keep the cord away
from the cutting area and position it so that it will
not be caught on the workpiece during the
cutting operation.
Operate with proper hand support, proper workpiece
support, and supply cord routing away from the work
area.
WARNING
It is important to support the work piece properly
and to hold the saw firmly to prevent loss of
control which could cause personal injury. Fig.1
illustrates typical hand support of the saw.
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
6
A TYPICAL ILLUSTRATION OF PROPER HAND
SUPPORT WORKPIECE SUPPORT, AND SUPPLY
CORD ROUTING.
Fig. 1
4. Place the wider portion of the saw base on that
part of the work piece which is solidly supported,
not on the section that will fall off when the cut is
made.
As examples, Fig. 2 illustrates the RIGHT way to cut
off the end of board, and Fig. 3 the WRONG way. If
the work piece is short or small, clamp it down.
DON’T TRY TO HOLD SHORT PLACES BY HAND!
Fig. 2
Fig. 3
5. Never attempt to saw with the circular saw held
upside down in a vise.
This is extremely dangerous and can lead to serious
accidents. (Fig. 4)
Fig. 4
6. ALWAYS wear ear protectors when using the tool
for extended periods.
Prolonged exposure to high intensity noise can cause
hearing loss.
7. Always wear eye protection that meets the
requirement of the latest revision of ANSI
Standard Z87.1.
8. ALWAYS wear a mask or respirator to protect
yourself from dust or potentially harmful
particles generated during operation.
9. Before setting the tool down after completing a
cut, be sure that the lower (telescoping) guard
has closed and the blade has come to a
complete stop.
10. NEVER touch moving parts.
NEVER place your hands, fingers or other body parts
near the tool’s moving parts.
11. NEVER operate without all guards in place.
NEVER operate this tool without all guards or safety
features in place and in proper working order. If
maintenance or servicing requires the removal of a
guard or safety feature, be sure to replace the guard
or safety feature before resuming operation of the
tool.
12. Use right tool.
Don’t force small tool or attachment to do the job of a
heavy-duty tool.
Don’t use tool for purpose not intended —for example
— don’t use circular saw for cutting tree limbs or logs.
13. NEVER use a power tool for applications other
than those specified.
NEVER use a power tool for applications other than
those specified in the instruction manual.
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
7
14. Handle tool correctly.
Operate the tool according to the instructions
provided herein. Do not drop or throw the tool.
NEVER allow the tool to be operated by children,
individuals unfamiliar with its operation or
unauthorized personnel.
15. Do not run the saw while carrying it at your side.
16. Keep all screws, bolts and covers tightly in
place.
Keep all screws, bolts, and plates tightly mounted.
Check their condition periodically.
17. Do not use power tools if the plastic housing or
handle is cracked.
Cracks in the tool’s housing or handle can lead to
electric shock. Such tools should not be used until
repaired.
18. Blades and accessories must be securely
mounted to the tool.
Prevent potential injuries to yourself or others. Blades,
cutting implements and accessories which have been
mounted to the tool should be secure and tight.
19. NEVER use a tool which is defective or operating
abnormally.
If the tool appears to be operating unusually, making
strange noises, or otherwise appears defective, stop
using it immediately and arrange for repairs by a
metaboHPT authorized service center.
20. Carefully handle power tools.
Should a power tool be dropped or struck against
hard materials inadvertently, it may be deformed,
cracked, or damaged.
21. Do not wipe plastic parts with solvent.
Solvents such as gasoline, thinner benzine, carbon
tetrachloride, and alcohol may damage and crack
plastic parts. Do not wipe them with such solvents.
Wipe plastic parts with a soft cloth lightly dampened
with soapy water and dry thoroughly.
22. Never wear gloves made of material liable to roll
up such as cotton, wool, cloth or string, etc.
23. Keep motor air vent clean.
The tool’s motor air vent must be kept clean so that
air can freely flow at all times. Check for dust build-up
frequently.
24. NEVER leave tool running unattended. Turn
power off.
Don’t leave tool until it comes to a complete stop.
25. NEVER touch the blade with bare hands after
operation.
26. Because the cordless power tool operates by battery
power, be aware of the fact that it can begin to
operate at any time.
27. When working at elevated locations, clear the area of
all other people and be aware of conditions below
you.
28. Do not give a strong shock to the switch panel or
break it. It may lead to a trouble.
29. Do not use the product if the tool or the battery
terminals (battery mount) are deformed.
Installing the battery could cause a short circuit that
could result in smoke emission or ignition.
30. Keep the tool’s terminals (battery mount) free of swarf
and dust.
○
Prior to use, make sure that swarf and dust have not
collected in the area of the terminals.
○
During use, try to avoid swarf or dust on the tool from
falling on the battery.
○
When suspending operation or after use, do not leave
the tool in an area where it may be exposed to falling
swarf or dust.
Doing so could cause a short circuit that could result
in smoke emission or ignition.
31. Definitions for symbols used on this tool
V.......................................................................... volts
.......................................................... direct current
n0
......................................................... no load speed
---/min............. revolutions or reciprocation per minute
Hz ....................................................................... hertz
A ................................................................... amperes
32. Always use the tool and battery at temperatures
between 23°F (-5°C) and 104°F (40°C).
IMPORTANT SAFETY INSTRUCTIONS FOR
BATTERY CHARGER
WARNING
Death or serious bodily injury could result from
improper or unsafe use of battery chargers. To
avoid these risks, follow these basic safety
instructions:
READ ALL INSTRUCTIONS
1. This manual contains important safety and operating
instructions for battery charger Model UC18YSL3.
2. Before using battery charger, read all instructions and
cautionary markings on (1) battery charger, (2)
battery, and (3) product using battery.
3. To reduce risk of injury, charge metaboHPT
rechargeable battery models of the multi volt series
and the BSL18 series. Other models of batteries may
burst causing personal injury and damage.
4. Use of an attachment not recommended or sold by
the battery charger manufacturer may result in a risk
of fire, electric shock, or injury to persons.
5. To reduce risk of damage to electric plug and cord,
pull by plug when disconnecting battery charger.
6. Make sure cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage or stress.
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
8
7. An extension cord should not be used unless
absolutely necessary. Use of improper extension cord
could result in a risk of fire and electric shock.
If extension cord must be used make sure:
a. That blades of extension cord are the same
number, size, and shape as those of plug on
battery charger:
b. That extension cord is properly wired and in good
electrical condition; and
c. That wire size is large enough for AC ampere
rating of battery charger as specified in Table1.
Table 1: RECOMMENDED MINIMUM AWG SIZE FOR
EXTENSION CORDS FOR BATTERY CHARGERS
AC Input Rating
Amperes *1AWG Size of Cord
Equal to
or
greater
than
but less
than
Length of Cord, Feet (Meter)
25
(7.5) 50
(15) 100
(30) 150
(45)
0
2
3
2
3
4
18
18
18
18
18
18
18
16
16
16
14
14
*1 If the input rating of a battery charger is given in watts
rather than in amperes, the corresponding ampere
rating is to be determined by dividing the wattage
rating by the voltage rating–for example:
1,250 watts
125 volts =10 amperes
8. Do not operate battery charger with damaged cord or
plug-replace them immediately.
9. Do not operate battery charger if it has received a
sharp blow, been dropped, or otherwise damaged in
any way; take it to a qualified serviceman.
10. Do not disassemble battery charger; take it to a
qualified serviceman when service or repair is
required. Incorrect reassembly may result in a risk of
electric shock or fire.
11. To reduce risk of electric shock, unplug charger from
receptacle before attempting any maintenance or
cleaning. Removing the battery will not reduce this
risk.
IMPORTANT SAFETY INSTRUCTIONS FOR
USE OF THE BATTERY AND BATTERY
CHARGER
You must charge the battery before you can use the
power tool. Before using the model UC18YSL3 battery
charger, be sure to read all instructions and cautionary
statements on it, the battery and in this manual.
WARNING
USE ONLY metaboHPT BATTERIES. OTHER
MODELS OF BATTERIES MAY BURST AND
CAUSE INJURY!
Follow these instructions to avoid the risk of injury:
WARNING
Improper use of the battery or battery charger
can lead to serious injury. To avoid these
injuries:
1. NEVER disassemble the battery.
2. NEVER incinerate the battery, even if it is damaged or
is completely worn out. The battery can explode in a
fire.
3. NEVER short-circuit the battery.
4. NEVER insert any objects into the battery charger’s
air vents. Electric shock or damage to the battery
charger may result.
5. NEVER charge outdoors. Keep the battery away from
direct sunlight and use only where there is low
humidity and good ventilation.
6. NEVER charge when the temperature is below 32°F
(0°C) or above 104°F (40°C).
7. NEVER connect two battery chargers together.
8. NEVER insert foreign objects into the hole for the
battery or the battery charger.
9. NEVER use a booster transformer when charging.
10. NEVER use DC power to charge.
11. NEVER store the battery or battery charger in places
where the temperature may reach or exceed 104°F
(40°C) such as inside metal box or car.
12. NEVER expose the battery or battery charger to rain
or wet conditions.
13. ALWAYS operate charger on standard household
electrical power (120 volts). Using the charger on any
other voltage may overheat and damage the charger.
14. ALWAYS wait at least 15 minutes between charges
to avoid overheating the charger.
15. ALWAYS disconnect the power cord from its
receptacle when the charger is not in use.
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
9
CAUTION ON LITHIUM-ION BATTERY
To extend the lifetime, the lithium-ion battery equips with
the protection function to stop the output.
In the cases of 1 to 3 described below, when using this
product, even if you are pulling the switch, the motor may
stop. This is not the trouble but the result of protection
function.
1. When the battery power remaining runs out, the motor
stops.
In such case, charge it up immediately.
2. If the tool is overloaded, the motor may stop. In this
case, release the switch of tool and eliminate causes
of overloading. After that, you can use it again.
3. If the battery is overheated under overload work, the
battery power may stop.
In this case, stop using the battery and let the battery
cool. After that, you can use it again.
Furthermore, please heed the following warning and
caution.
WARNING
In order to prevent any battery leakage, heat
generation, smoke emission, explosion and ignition
beforehand, please be sure to heed the following
precautions.
1. Make sure that swarf and dust do not collect on the
battery.
○
During work make sure that swarf and dust do not fall
on the battery.
○
Make sure that any swarf and dust falling on the
power tool during work do not collect on the battery.
○
Do not store an unused battery in a location exposed
to swarf and dust.
○
Before storing a battery, remove any swarf and dust
that may adhere to it and do not store it together with
metal parts (screws, nails, etc.).
2. Do not pierce battery with a sharp object such as a
nail, strike with a hammer, step on, throw or subject
the battery to severe physical shock.
3. Do not use an apparently damaged or deformed
battery.
4. Do not use the battery for a purpose other than those
specified.
5. If the battery charging fails to complete even when a
specified recharging time has elapsed, immediately
stop further recharging.
6. Do not put or subject the battery to high temperatures
or high pressure such as into a microwave oven,
dryer, or high pressure container.
7. Keep away from fire immediately when leakage or
foul odor are detected.
8. Do not use in a location where strong static electricity
generates.
9. If there is battery leakage, foul odor, heat generated,
discolored or deformed, or in any way appears
abnormal during use, recharging or storage,
immediately remove it from the equipment or battery
charger, and stop use.
10. Do not immerse the battery or allow any fluids to flow
inside. Conductive liquid ingress, such as water, can
cause damage resulting in fire or explosion. Store
your battery in a cool, dry place, away from
combustible and flammable items. Corrosive gas
atmospheres must be avoided.
CAUTION
1. If liquid leaking from the battery gets into your eyes,
do not rub your eyes and wash them well with fresh
clean water such as tap water and contact a doctor
immediately.
If left untreated, the liquid may cause eye-problems.
2. If liquid leaks onto your skin or clothes, wash well with
clean water such as tap water immediately.
There is a possibility that this can cause skin irritation.
3. If you find rust, foul odor, overheating, discolor,
deformation, and/or other irregularities when using
the battery for the first time, do not use and return it to
your supplier or vendor.
WARNING
If an electrically conductive foreign object enters the
terminals of the lithium ion battery, a short-circuit may
occur resulting in the risk of fire. Please observe the
following matters when storing the battery.
●
Do not place electrically conductive cuttings,
nails, steel wire, copper wire or other wire in the
storage case.
●
Either install the battery in the power tool or
store by securely pressing into the battery cover
until the ventilation holes are concealed to
prevent short-circuits (See Fig. 7).
REGARDING LITHIUM-ION BATTERY
TRANSPORTATION
When transporting a lithium-ion battery, please observe
the following precautions.
WARNING
Notify the transporting company that a package
contains a lithium-ion battery, inform the
company of its power output and follow the
instructions of the transportation company when
arranging transport.
●
Lithium-ion batteries that exceed a power output
of 100Wh are considered to be in the freight
classification of Dangerous Goods and will
require special application procedures.
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
10
●
For transportation abroad, you must comply with
international law and the rules and regulations of
the destination country.
Wh
Power Output
2 to 3 digit number
Fig. 5
SAVE THESE INSTRUCTIONS
AND
MAKE THEM AVAILABLE TO OTHER USERS
AND
OWNERS OF THIS TOOL!
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
11
FUNCTIONAL DESCRIPTION
NOTE
The information contained in this Instruction Manual is designed to assist you in the safe operation and maintenance
of the power tool.
NEVER operate, or attempt any maintenance on the tool unless you have first read and understood all safety
instructions contained in this manual.
Some illustrations in this Instruction Manual may show details or attachments that differ from those on your own
power tool.
NAME OF PARTS
1.Cordless Metal Cutting Saw (CD1805DB)
Lighting mode switch
Lighting mode indicator lamp
Remaining battery
indicator lamp
Silent mode indicator lamp
Mode selector
switch
Switch panel
Sub handle
LED Light
Motor
(Inside the Housing)
Hex. bar wrench 5mm
Battery
Nameplate
Gear cover
Dust cover
Cutting depth lever
Saw blade Guide slit
Base
Lock lever
Saw cover
Trigger switch
Lock-off button
Lower guard
Washer (B)
Hexagonal flange bolt
Dust box
Mark
Push button
Handle
Fig. 6
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
12
2.Battery 3.Battery Charger
Ventilation holes
Display panel
Battery cover
Terminals
Latch
Cord
Nameplate Guide rail
Ventilation holes
Charge indicator
lamp
<BSL36A18X>
Fig. 7
<UC18YSL3>
Fig. 8
SPECIFICATIONS
1.Cordless Metal Cutting Saw
Model CD1805DB
Voltage 18 V
Motor DC brushless motor
No-load speed 4,200 /min (Power mode)
2,200 /min (Silent mode)
Blade Size 5-3/8" (135mm)–5-7/8" (150mm) × 25/32" (20mm) H
Max. Cutting Depth 2" (51mm)–2-17/64" (57.5mm)
Power supply Type Li-ion battery Model BSL36A18X
Voltage DC 36 V / 18 V
Weight 6.6lbs. (3.0kg) (BSL36A18X attached)
2.Battery Charger
Model UC18YSL3
Input power source Single phase: AC 120 V 60 Hz
Charging time
(At a temperature of 68°F (20°C)) BSL36A18X: Approx. 32min
Charging voltage DC 14.4–18V
Charging current DC 8.0A
Weight 1.3lbs. (0.6kg)
NOTE
The charging time may vary according to temperature and power source voltage.
Electronic control
○
Soft-start
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
13
○
Overload protection
This protection feature cuts off the power to the motor in the event of overloading of motor or a conspicuous
reduction in rotational speed during operation.
When the overload protection feature has been activated, the motor may stop.
In this case, release the tool switch and eliminate causes of overloading.
After that you can use it again.
○
Overheat protection
This protection feature cuts off the power to the motor and stops the power tool in the event of overheating of motor
during operation.
When the overheat protection feature has been activated, the motor may stop.
In this case, release the tool switch and cool it down in a few minutes.
After that you can use it again.
○
Rotation speed changeover function (Power mode / Silent mode)
(Power mode / Silent mode switch function)
Each press of the Mode Selector Switch changes the operating mode.
Silent mode reduces maximum motor RPM enabling efficient work with less noise.
The Silent Mode Indicator Lamp lights in Silent mode.
When the load increases during Silent mode, the tool will automatically switch to Power mode and revert back to
Silent mode when the load decreases.
In Power mode, no change is made to Silent mode even when the load decreases.
CAUTION
Do not give a strong shock to the switch panel or break it. It may lead to a trouble.
NOTE
To enable mode changes, pull the switch once after installing the battery.
Mode selector switch
Silent mode indicator lamp
Fig. 9
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
14
ASSEMBLY AND OPERATION
APPLICATIONS
○
For cutting various types of soft steel materials such
as flat steel strips, pipe, steel channels (“C” channels,
“L” angles, etc.) and aluminum sash.
–
It is possible to cut aluminum. However, when
doing so, apply cutting oil to the edge of the
blade.
CAUTION
●
Cannot be used for cutting tempered steel
materials.
●
Do not consecutively cut metal plates.
REMOVAL AND INSTALLATION METHOD
OF BATTERY
○
How to install the battery.
Align the battery with the groove in tool handle and
slip it into place.
Always insert it all the way until it locks in place with a
little click, If not, it may accidentally fall out of the tool,
causing injury to you or someone around you.
○
How to remove the battery.
Withdraw battery from the tool handle while pressing
the latch (2pcs) of the battery.
Handle
Latch
Battery
Pull outInsert
Push
Fig. 10
CHARGING METHOD
NOTE
Before plugging into the receptacle, make sure the
following points.
○
The power source voltage is stated on the nameplate.
○
The cord is not damaged.
WARNING
Do not charge at voltage higher than indicated
on the nameplate.
If charged at voltage higher than indicated on the
nameplate, the charger will burn out.
<UC18YSL3>
1. Connect the charger’s power cord to a receptacle.
When the power cord is connected, the charge
indicator lamp will blink in red. (See Table 2)
WARNING
Do not use the electrical cord if damaged. Have it
repaired immediately.
2. Insert the battery to the battery charger.
Insert the battery into the battery charger.
Charge
indicator lamp
Battery
Guide rail
Fig. 11
3. Charging
When inserting a battery in the charger, charging will
commence and the charge indicator lamp will blink in
blue.
When the battery becomes fully recharged, the
charge indicator lamp will light up in green. (See
Table2)
(1) Charge indicator lamp indication
The indications of the charge indicator lamp will be as
shown in Table2, according to the condition of the
battery charger or the battery.
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
15
Table 2:Indications of the charge indicator lamp
ON/OFF at 0.5 sec. intervals
(RED) Before charging *1
Lights for 0.5 sec. at intervals
of 1 sec. (BLUE) Charged at less than
50%
Lights for 1 sec. at intervals of
0.5 sec. (BLUE) Charged at less than
80%
Lights continuously (BLUE) Charged at more than
80%
Lights continuously
(Continuous buzzer sound:
about 6 sec.) (GREEN) Charging complete
ON/OFF at 0.3 sec. intervals
(RED) Overheat standby *2
ON/OFF at 0.1 sec. intervals
(Intermittent buzzer sound;
about 2 sec.) (PURPLE) Charging impossible *3
NOTE
*1 If the red lamp continues to blink even after the
charger has been attached, check to confirm that the
battery has been fully inserted.
*2 Battery overheated. Unable to charge.
Although charging will start once the battery has
cooled down even when left in situ, the best practice
is to remove the battery and allow it to cool down in a
shaded, well-ventilated location before charging.
*3 Malfunction in the battery or the charger
–
Fully insert the battery.
–
Check to confirm that no foreign matter is stuck
to the battery mount or terminals. If there are no
foreign objects, it is probable that the battery or
charger is malfunctioning. Take it to your
authorized Service Center.
○
When the battery charger has been continuosly used,
the battery charger will be heated, thus constituting
the cause of the failures. Once the charging has been
completed, give 5minutes rest until the next charging.
(2) Regarding the temperature of the rechargeable
battery.
Table 3
Rechargeable
batteries Temperatures at which the battery
can be recharged
BSL36A18X 32°F–122°F
(0°C–50°C)
(3) Regarding recharging time (At 68°F (20°C))
Table 4:Charging time
Battery Charger: UC18YSL3
BSL36A18X Approx. 32 min
NOTE
○
The recharging time may vary according to the
ambient temperature.
○
If charging takes a long time
–
Charging will take longer at extremely low
ambient temperatures. Charge the battery in a
warm location (such as indoors).
–
Do not block the air vent. Otherwise the interior
will overheat, reducing the charger’s
performance.
–
If the cooling fan is not operating, contact a
metaboHPT Authorized Service Center for
repairs.
4. Disconnect battery charger from the receptacle.
CAUTION
Do not pull the plug out of the receptacle by
pulling on the cord.
Make sure to grasp the plug when removing from
receptacle to avoid damaging cord.
5. Remove the battery from the battery charger.
Supporting the battery charger with hand, pull out the
battery from the battery charger.
NOTE
Be sure to pull out the battery from the battery charger
after use, and then keep it.
Regarding electric discharge in case of new
batteries, etc.
As the internal chemical substance of new batteries and
batteries that have not been used for an extended period
is not activated, the electric discharge might be low when
using them the first and second time. This is a temporary
phenomenon, and normal time required for recharging will
be restored by recharging the batteries 2–3 times.
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
16
How to make the batteries perform longer
(1) Recharge the batteries before they become
completely exhausted.
When you feel that the power of the tool becomes
weaker, stop using the tool and recharge its battery. If
you continue to use the tool and exhaust the electric
current, the battery may be damaged and its life will
become shorter.
(2) Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after
use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate,
and the battery life will be shortened. Leave the
battery and recharge it after it has cooled for a while.
HOW TO RECHARGE USB DEVICE
When an unexpected problem occurs, the data in a USB
device connected to this product may be corrupted or lost.
Always make sure to back up any data contained in the
USB device prior to use with this product.
Please be aware that our company accepts absolutely no
responsibility for any data stored in a USB device that is
corrupted or lost, nor for any damage that may occur to a
connected device.
WARNING
●
Prior to use, check the connecting USB cable for
any defect or damage.
Using a defective or damaged USB cable can
cause smoke emission or ignition.
●
When the product is not being used, cover the
USB port with the rubber cover.
Buildup of dust etc. in the USB port can cause
smoke emission or ignition.
NOTE
○
The time required for charging will be longer when a
USB device and battery are being simultaneously
charged.
○
There may be an occasional pause during USB
recharging.
○
When a USB device is not being charged, turn the
USB power switch OFF and remove the USB device
from the charger.
Failure to do so may not only reduce the battery life of
a USB device, but may also result in unexpected
accidents.
(1) Select a charging method
Depending on the charge method selected, either the
battery is inserted into the charger or the power cord
is plugged into an outlet.
○
Charging a USB device by battery
○
Charging a USB device from a electrical outlet
○
Charging a USB device and battery from a electrical
outlet
a b c
Fig. 12
(2) Turn the USB power switch ON
When you turn the USB power switch ON, the USB
power indicator lamp will light up.
Rubber cover
USB cable
USB port
USB power
indicator lamp
USB power switch
Fig. 13
(3) Connect the USB cable.
Pull back the rubber cover and firmly plug in a
commercially available USB cable (appropriate to the
device being charged) into the USB port.
○
When the power cord is not plugged into an outlet
and the battery runs out of power, power output will
stop and the USB power indicator lamp will shut off.
○
When the USB power indicator lamp goes out,
change the battery or plug the power cord into an
electrical outlet.
(4) When charging is completed
○
The USB power indicator lamp will not go out when a
USB device has been completely charged.
To verify charge status, check the USB device.
○
Turn the USB power switch OFF and unplug the
power cord from the electrical outlet.
○
Remove the battery from the charger and place the
rubber cover over the USB port.
<USB device charging stops midway>
○
Charging stops for approximately five seconds to
allow the power supply to be detected under the
following conditions: if the battery charger power plug
is plugged in while charging a USB device from the
battery, or if a rechargeable battery is inserted while
charging a USB device from the battery charger.
○
USB charging stops for five seconds so that checking
can be performed once the rechargeable battery has
been fully charged.
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
17
○
If the rechargeable battery level is extremely low,
charging the rechargeable battery takes priority, and
USB charging is temporarily stopped. USB charging
automatically resumes once the battery level has
reached a preset level.
PRIOR TO OPERATION
WARNING
To avoid serious accident, ensure the switch is
in the OFF position, and pull out the battery.
1. Check the work area environment
Check the work area to make sure that it is clear of
debris and clutter.
Clear the area of unnecessary personnel. Ensure that
lighting and ventilation is adequate.
2. Removal/installation of dust box
○
Removal
Press the push button to remove the dust box.
1
2
Push button
Dust box
Fig. 14
○
Installation
Hang the lower hooks (2 places) on the main body,
insert the upper push button, and attach the dust box
to the main body.
Push button
Dust box
Hook
Fig. 15
3. Changing saw blades
WARNING
●
Use the hex. bar wrench 5mm that is supplied
with the power tool. Do not use other tools as
this may result in over-tightening or insufficient
tightening of the hexagonal flange bolt that holds
the blade in place causing accidents.
●
Perform replacement of the saw blade on a
stable surface or floor.
CAUTION
●
Use only sharp, undamaged saw blades. Do not
use saw blades that are cracked or that have
changed their shape.
●
Never touch the saw blade immediately after use.
The metal is hot and can easily burn your skin.
(1) Press the push button to remove the dust box.
(2) Depress the lock lever, lock the spindle, and remove
the hexagonal flange bolt and washer (B) with the
hex. bar wrench 5 mm.
Hex. bar wrench 5 mm
Lock lever
Loosen
Fig. 16
(3) While holding the end of the lower guard to keep the
lower guard fully retracted into the saw cover, remove
the saw blade.
Saw blade Lower guard
Saw cover
Fig. 17
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
18
NOTE
○
Before installing the saw blade, thoroughly remove
any sawdust which has accumulated on the spindle,
hexagonal flange bolt, and washers.
○
For mounting saw blade, the concave sides of both
washers (A) and (B) must be fitted to the saw blade
sides.
Washer (A)
Washer (B)
Hexagonal
Flange Bolt
Saw Blade
Fig. 18
(4) If washer (A) was removed, install it on the main unit
first. Next, mount the saw blade on the spindle, and
finally, affix washer (B).
(5) To assure proper rotation direction of the saw blade,
the arrow direction on the saw blade must coincide
with the arrow direction on the saw cover.
(6) Using the fingers, tighten the hexagonal bolt retaining
the saw blade as much as possible. Then depress the
lock lever, lock the spindle, and thoroughly tighten the
hexagonal flange bolt.
(7) Confirm that the lock lever is in the original position.
(8) Attach the dust box. (Fig.15)
CAUTION
After mounting the saw blade, reconfirm that the
lock lever has returned to its original position.
4. Check performance of lower guard
WARNING
Make absolutely sure that the lower guard is not
fixed. Also, check and see if it can move
smoothly. If the saw blade is kept exposed,
injury can result.
The lower guard (refer to Fig. 6) serves to protect your
body from coming into contact with the saw blade. Make
absolutely certain that the cover smoothly performs to
cover the saw blade. If the lower guard should not move
smoothly, never use it without repairing it.
In such a case, get in touch with the store where you
bought the power tool or the metaboHPT AUTHORIZED
SERVICE CENTER for necessary repair.
5. Check for proper operation of the brake
This power tool features an electric brake that
functions when the switch is released. Before use,
ensure that the electric brake functions properly.
If it does not, bring the tool to a metaboHPT
AUTHORIZED SERVICE CENTER.
6. Prepare a work bench
Since the saw blade will extend beyond the lower
surface of the steel materials, place the steel
materials on a work bench when cutting. If a square
block is utilized as a work bench, select level ground
to ensure it is properly stabilized. An unstable work
bench will result in hazardous operation.
Steel materials Base
Saw blade
Work bench
Fig. 19
CAUTION
To avoid possible accident, always ensure that
the portion of steel materials remaining after
cutting is securely anchored or held in position.
ADJUSTSING THE SAW PRIOR TO USE
WARNING
To avoid serious accidents, ensure the switch is
in the OFF position, and pull out the battery.
1. Adjusting the cutting depth
Loosen
Tighten
Cutting
depth lever
Base
Fig. 20
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
19
WARNING
If the cutting depth lever is loose, injury can
result. Tighten it securely after adjustment.
To adjust cutting depth, loosen the cutting depth lever
and, while holding the base with one hand, move the main
body up and down to obtain the prescribed cutting depth.
After adjusting to the prescribed cutting depth, tighten the
cutting depth lever securely.
2. Regulating the guide (Rip fence)
..................................................... Optional Accessory
Install the wing bolt and lock spring on the base. Insert the
guide into the base, move it left and right and adjust the
cutting position. Tighten the wing bolt and fix the guide.
The guide can be installed either from the left or the right
side of the main body.
Wing Bolt
Lock Spring
Base
Fig. 21
Wing Bolt
Base
Guide
(Rip Fence)
Fig. 22
OPERATION
WARNING
●
Never touch the moving parts.
●
Never operate the power tool with the saw blade
turned upward or to the side.
●
Do not fix and secure the lock-off button.
Besides, keep your finger off the trigger switch
when the power tool is being carried around.
Otherwise, the main body switch can be
inadvertently turned ON, resulting in unexpected
accidents.
●
Do not use any saw blades which do not conform
to the specified rating.
●
The saw blade must be suitable for the no-load
speed.
●
Use a saw blade that is suitable for the material
being sawn.
●
Use only genuine metaboHPT saw blades.
●
Do not use any abrasive wheels.
●
Use only blade diameter specified on the product
nameplate.
●
Should the saw blade be stopped or make an
abnormal noise during operation, turn off the
switch immediately.
●
Always wear eye protection with side shields
that meets the requirements of ANSI Standard
Z87.1.
CAUTION
●
Use this product only for cutting metal.
●
Cannot be used for cutting tempered steel
materials.
●
To extend the lifetime, the lithium-ion battery
equips with the protection function to stop the
output. Therefore, if the tool is overloaded, the
motor may stop. However, this is not the trouble
but the result of protection function. In this case,
release the switch of tool and eliminate the
causes of overloading.
●
Take care not to lock the motor. If the motor is
locked, immediately turn the power off. If the
motor is locked for a while, the motor or battery
may be burnt.
1. Check if saw blade is tightened
While the saw blade is tightened securely for
immediate use when it is assembled at the factory, be
sure to check it out again for caution’s sake. A bolt
can be tightened when it is turned clockwise. Use the
provided hex. bar wrench 5mm to check it out.
Please refer to “3. Changing saw blades” in [PRIOR
TO OPERATION] for details.
2. Check if the lever is tightened (Fig.20)
If the cutting depth lever is loose, injury can result.
Make sure that it is tightened securely.
3. Check performance of lower guard
Please refer to “4. Check performance of lower guard”
in [PRIOR TO OPERATION] for details.
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
English
20
4. Check battery insertion
WARNING
If the battery is inserted while the power switch
is in the ON position, the power tool will start
operating immediately, inviting serious accident.
CAUTION
Until the battery locks in place with a little click,
if not, it may accidentally fall out of the tool
causing injury to you or someone around you.
5. Operation of switch
For safe operation of the machine, a “lock-off button”
is provided on the side of the handle.
If the trigger switch is pulled while the lock-off button
is pressed in the direction of either of the arrow
marks, the main switch can be turned ON.
After the switch is on, the saw blade will continue to
operate as long as you pull on the trigger switch, even
if you release the lock-off button.
Lock-off button
Trigger switch
Fig. 23
6. Check for proper operation of the brake
Please refer to “5. Check for proper operation of the
brake” in [PRIOR TO OPERATION] for details.
7. About the mode select function
Each time the mode selector switch is pushed, the
operation mode changes.
When Silent mode is selected, the Silent mode
indicator lamp lights up.
Silent mode reduces maximum motor RPM enabling
efficient work with less noise.
If the load increases while the motor is operating in
Silent mode, it automatically changes to Power mode.
Additionally, if the load decreases again, it
automatically returns to Silent mode.
In Power mode, no change is made to Silent mode
even when the load decreases.
Mode selector switch
Silent mode indicator lamp
Switch panel
Fig. 24
Mode No-load speed
Power 4,200 /min
Silent 2,200 /min
NOTE
○
The mode will only change after a battery is installed
and the switch is pulled once.
○
The current mode will be maintained even if the
switch is on/off, or the battery is removed/reinserted.
8. About Remaining Battery Indicator
Remaining battery power can be verified by pulling on
the switch to make the remaining battery indicator
lamp light up red. (See Table5)
The indicator lamp will change to the lighting mode
indicator lamp (green) 10seconds after the switch is
released.
Remaining battery Indicator lamp (red)
Switch panel
Fig. 25
2023/07/25 17:56:03Stylesheet: NA Version: 2023.7.18
CD1805DB_C99277162_306_NA
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
Hikoki CD1805DB Manuel utilisateur
- Catégorie
- Outils électroportatifs
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Hikoki CD1805DB User manual
- español: Hikoki CD1805DB Manual de usuario
Documents connexes
-
Hikoki C3607DB Manuel utilisateur
-
-
-
-
-
-
-
-
-
Metabo HPT Multivolt CB 3612DA Manuel utilisateur