Zodiac Edenpac 5D Instructions For Installation And Use Manual

Ed. 04/2007 - EDPAC045DFAB - EDPAC057DFAB - EDPAC067DFAA

Réf. : 1011475-02

Heat pump ...............................................................Instructions for installation and use

F

GB

D

NL

E

P

I

4D - 5D - 6D

All seasons

F

GB

D

NL

E

P

I

IMPORTANT

These installation instructions are an integral part of the product and must be given to the installer

and kept by the user.

The warnings and indications contained in the present handbook must be carefully read and

understood as they provide important information relative to handling and operating safety. This

handbook must therefore always be kept available for later consultation.

Installation must be carried out in compliance with valid regulations and the manufacturer’s

instructions by a qualified professional.

The term «qualified professional» refers to a person possessing the technical knowledge associated

with P.S.A. components and heating installations.

An installation error could result in physical injury to persons or animals as well as mechanical

damage for which the manufacturer may under no circumstances be held responsible.

After having unpacked the heat pump, the content should be checked for possible damage.

Before connecting the heat pump, ensure that the data provided by P.S.A. is compatible with the

true installation conditions and does not exceed the maximum authorised limits for the product in

question.

Before beginning any installation, handling or repair work on the heat pump, always isolate the

electrical power supply to the unit.

In the case of a fault and/or operating error on the heat pump, the electrical power supply must be

isolated and no attempt should be made to repair the fault.

Repair work may only be carried out by an authorised technical assistance service using original

spare parts only. Non-respect of the aforementioned clauses may have a negative influence on

the operating safety of the heat pump.

To guarantee the efficiency and correct operation of the heat pump, it is important to ensure it is

regularly maintained in compliance with the instructions provided by P.S.A.

In the case where a heat pump is sold or transferred to another user, always ensure that all technical

documentation is sent with the equipment to be used by the new user or installer.

This heat pump may only be used for the purpose for which it was designed: to heat a swimming

pool; all other uses must be considered inappropriate, incorrect or even dangerous.

All contractual or extra-contractual responsibilities of P.S.A. will be considered nil and void for any

damage caused by installation or operating errors, or due to non-respect of the instructions

provided by P.S.A. or valid installation standards for the equipment object of the present document.

1

CONTENTS

1 General.................................................. 2

1.1 General terms of delivery..............................2

1.2 Voltage..........................................................2

1.3 Water treatment.............................................2

2 Description............................................ 2

2.1 Presentation...................................................2

2.1.1 Edenpac 4 and 5 D

2.1.2 Edenpac 6 D

2.2 Dimensional characteristics........................... 5

2.2.1 Edenpac 4 and 5 D

2.2.2 Edenpac 6 D

3 Installation............................................ 7

4 Connections .......................................... 9

4.1 Access to the electrical card .............................9

4.1.1 Edenpac D with single fan

4.1.2 Edenpac D with double fan

4.2 Hydraulic connections......................................10

4.3 Electric connections..........................................11

5 Regulator operation............................. 12

5.1 Presentation...................................................... 12

5.2 Setting the target temperature...........................13

6 Starting up............................................ 13

6.1 Check................................................................14

6.2 Start up the heat pump......................................14

6.3 Checking...........................................................15

6.4 Troubleshooting................................................ 15

6.5 Complete shutdown for storage........................16

7 Maintenance instructions.................... 17

8 Recycling the product.......................... 17

9 Electrical diagrams.............................. 17

9.1 Electrical diagram of connection

Interface card....................................................18

9.2 Electrical diagram EdenPAC D single-phase...19

9.3 Electrical diagrams EdenPAC D three-phase...20

2

1. GENERAL

1.1 General terms of delivery

Any equipment, even CARRIAGE and PACKING FREE, travel at the consignee’s risk. The consignee shall make

reserves in writing on the CARRIER’S delivery bill if he notes damage caused during transport. (Confirmation to be sent

to the CARRIER within 48 hours by registered mail with acknowledgement of receipt).

Reminder: The unit must be shipped and stored in the upright position on a pallet and in the original packaging. In the contrary

case, place the unit in the vertical position on the pallet and check its global state (in case of doubt regarding the unit’s good state of

operation establish reserves in writing with the carrier).

- Under no circumstances may the heat pump be operated immediately if it was placed horizontally.

Wait at least 12 hours before operating the pump -

1.2 Voltage

Prior to any operation, check that the voltage on the name plate of the appliance corresponds to the mains voltage

provided on site.

1.3 Water treatment

In order to use our appliances under the best conditions, the following parameters must be respected: free chlorine: max.

2.5 mg/l, total bromine: max. 5.5 mg/l, pH between 6.9 and 8.0. If chemical or electrophysical disinfection systems are

used, the installer and user must contact the supplier to ensure they are compatible with our materials. These systems must

be installed after the heating system.

2. DESCRIPTION

2.1 Presentation

Contents after unpacking:

The unit with its instructions, warranty card

Note: inside the appliance you will find a sachet of accessories. To extract it, see paragraph 4.1 of these instructions.

Content of sachet:

two half-union connectors Ø50 with strap  + two sealing rings  - four silent blocks 

a

g

rooved elbow union .- a

p

lastic ca

p

- four anchor bolts and dowels 

(

onl

y

su

pp

lied with double fan uni

t

)

.











Must be installed

with a double fan

machine

+

3

2.1.1 Edenpac 4 and 5 D

1 Front panel with polypropylene grid.

2 Motor fan unit.

3 Access flap to digital regulator 3a

(Euro α FK) & and pressure gauge ″water flow″3b

(measures the refrigerant pressure in the HP circuit

and is used to regulate the water flow-rate).

4 Electric board.

5 HP pressure switch.

6 Flow switch.

7 TITANIUM condenser .

8 Control sensor.

9 LP pressure switch.

 Cased SCROLL compressor

11 Arched “plate fin” evaporator.

12 Anti-frost sensor.

13 Fastening plates

(with silent blocks).

14 Pool inlet water connection

(40/49 male screw fastening).

15 Packing gland (and/or cable inlet).

16 Pool outlet water connection

(40/49 male screw fastening).

17 Removable polypropylene panel

to access the technical compartment.

18 Closing snap clips.

19 4-way valve.

20 Anti-frost heater.

21 By-flow expansion valve.

11

12

13

14

15

16

17

Attention! never use the panel reinforcement as a

load-bearing support .

20

1

2

3 4 5 6

7

8

9

 19

21

18

3a

3b

4

2.1.2 Edenpac 6 D

13 Fastening plates.

14 Pool inlet water connection

(40/49 male screw fastening).

15 Packing gland (and/or cable inlet).

16 Pool outlet water connection

(40/49 male screw fastening).

17 Removable polypropylene panel

to access the technical compartment.

18 Closing snap clips.

19 4-way valve.

20 Anti-frost heater.

21 By-flow expansion valve.

1 Top and bottom panels with polypropylene grid.

2 Motor fan unit.

3 Access flap to digital regulator 3a

(Euro α FK) & and pressure gauge ″water flow″3b

(measures the refrigerant pressure in the HP circuit

and is used to regulate the water flow-rate).

4 Electric board.

5 HP pressure switch.

6 Flow switch.

7 TITANIUM condenser.

8 Control sensor.

9 LP pressure switch.

 Cased SCROLL compressor

11 Arched “plate fin” evaporator.

12 Anti-frost sensor.

Attention! never use the panel reinforcement as a

load-bearing support .

17

18

3a

3b

16

14

15

12

11

1

2

4

6

9

7

5

3

8



13

19

20

21

5

2.2 Dimensional characteristics

2.2.1 Edenpac 4 and 5 D

Dimensions of the appliance with packaging (in mm) :

Weight of Edenpac 4 D with packaging : ≅ 105 kg

Weight of Edenpac 5 D with packaging : ≅ 110 kg

1275

480

870

To be transported upright in its original

packaging close to the installation site.

6

2.2.2 Edenpac 6 D

7

Dimensions of the appliance with packaging (in mm) :

Weight of Edenpac 6 D with packaging: ≅ 142 kg

3. INSTALLATION

Tools required for installation :

- 1 set of flat head screwdrivers

- 1 set of crosshead screwdrivers

- 1 cutter

- 1 wire stripper

- 1 pipe or round head spanner 13

- 1 ratchet spanner

- 1 pliers

- 2 straps (for handling)

Choose the appliance installation site according to the following criteria:

• the appliance must be installed outdoors

• the clearance around the appliance must be respected

(see minimum dimensions on the drawings below) to avoid recycling of cold air produced.

vers égout

 Dense obstacle (hedge, wall, fencing).

1370



To be transported upright in its original

packaging close to the installation site.

1275

480

8

• the installation must be simple and allow for easy maintenance interventions.

• the appliance must be installed on a solid base (fastening centre distance 810 x 370) and protected against

flooding (using a « concrete » base with drain facility for condensation or installation of an additional condensation

evacuation kit placed at your disposal in the accessories sachet). The silent blocks supplied must be used, paying

attention not to compress them too much when tightening the fastening screws .

• the appliance must be level to allow for the gravitational evacuation of possible condensation produced during

operation.

• the blower must not be directed towards surrounding windows.

• vibrations and noise must not be transmitted to a building close by.

• the heat pump must be installed at a minimum distance from the end of the pool, as defined by the applicable

national electrical standards. In France, standard NF C 15 100 (section 702) specifies that the appliance must not be

installed less than 2 metres from the pool or water reserve, but may be installed between 2 and 3.50 metres if there

are not water jets. In the contrary case, respect a minimum distance of 3.5 metres.

Attention ! :

• Do not lift the appliance by picking it up at the front and/or the water inlet/outlet points. Use 2 lifting slings (not

supplied) placed on either side of the appliance (see drawing below). The handle on the right side may be used only to help

with the final positioning of the appliance.

• Do not install the heat pump close to an inflammable gas source.

• Do not install the heat pump close to a road or path to protect the appliance against mud splashing.

• Avoid places that are subject to strong winds, in particular if the wind blows against the appliance’s air outlet.

• The installation as well as electric and hydraulic connections must be carried out in compliance with applicable standards, in

particular standard NF C 15 100 for France (equivalent to CE I 364) .

• Keep the appliance out of reach of children.

To use the additional condensation evacuation

kit:

- Use the grooved elbow union and cap.

- The tank is equipped with two evacuation holes, one for the

cap  and the other for the grooved elbow union  (their

position is interchangeable).

Note: To facilitate installation raise the unit 100 mm above

the ground with the additional blocks  made of a hard,

water-resistant material (not supplied).





Slings



9

4. CONNECTIONS

4.1 Access to the electric card

4.1.1 Edenpac D with single fan

 Turn the clips ¼ turn clockwise on the front panel 1 using a flat head screwdriver.

 Unscrew the 2 screws 2 and 3 on the right side using a cross head screwdriver.

 Slide the entire front panel forward and then down.

4.1.2 Edenpac D with double fan

 Turn the 2 clips 1a and 1b in the front ¼ turn clockwise using a flat head screwdriver.

 Unscrew the 2 screws 2 and 3 on the right side using a cross head screwdriver.

 Slide the entire front panel forward and then down.

1

2

3

1b

1a

2

3

10

4.2 Hydraulic connections

Connect the appliance’s PVC Ø 50 hose water inlet and outlet (according to symbols) to the removable fittings provided

with the heat pump. See symbols : for inlet and for outlet.

Connection is established with a by-pass on the pool filtration circuit after the filter and before the water treatment device

(see diagrams below).

- Hydraulic circuit test pressure: 3 bars - Hydraulic circuit operating pressure: 1.5 bar

Edenpac 4 and 5 D : - Average water flow 6.5 m3/h- pressure drop 1.7 mCE (0.17 bar) –

Edenpac 6 D : - Average water flow 7.5 m3/h- pressure drop 1.1 mCE (0.11 bar) –

V1-V2-V3 : By-pass valve

V5-V4 : Regulator valve*

* Recommended to facilitate

adjustment close to the unit.

V1-V2-V3 : By-pass valve

V5-V4 : Regulator valve*

* Recommended to facilitate

adjustment close to the machine.

V1

V2 V3

V4

V5

V1

V2 V3

V4

V5

11

4.3 Electric connections

• The power supply of the heat pump must pass via a protection facility and circuit-breaker (not supplied) in

compliance with applicable standards and regulations.

• The appliance is foreseen for connection to the mains circuit with TT and TN.S neutral connection (according to

NF C 15-100 or national standards in force).

• Supply cable section : ** protection:

- Edenpac 6 D: 5 x 2.5 mm² * (three-phase 400V/3N/50Hz) Ù 16 A

- Edenpac 5 D: 5 x 2.5 mm² * (three-phase 400V/3N/50Hz) Ù 12 A

- Edenpac 4 D: 3 x 6 mm² * (single-phase 230V/1/50Hz) Ù 32 A

* This section is indicative and must be checked and adapted, if necessary, according to installation conditions .

• Electrical protection: circuit breaker (curve D) or fuse (Am) delayed designed for motors adapted to the type of

unit (see ** below) with a protection system by 30 mA differential on the incoming supply side (circuit breaker or

switch).

Note: • The acceptable voltage variation during operation is ± 10%

• The cable ways and ducts must be fastened.

• Only use cable suitable for outdoor use.

• Use the packing glands and cable inlets to feed the cables into the unit.

Optional remote control functions:

Remote On/Off start up

The terminals 1 and 2 of the Edenpac heat pump enable a remote start up by means of a switch or any other device.

The heat pump is supplied with a jumper between these terminals. If this function is used, the jumper shall be

removed. Otherwise it shall be kept.

Remote failure light

In order to indicate in a technical facility that the heat pump is failing, terminals 0 and 4 provide a signal that can be

connected to a light or an alarm (230 V).

Priority to heating

A heating device, whatever it is, is designed to heat the water of the pool only when the water circulates. Most of

the time, a pool is filtered between 6 and 8 hours a day. But such a time can’t be sufficient sometimes to maintain

the water at the desired temperature, depending on the seasons. This is the reason why the Edenpac, like all models

of PSA’s range, is equipped with the “priority to heating” function that will manage the temperature of the pool,

taking itself the time to do it without caring of the scheduled time of operation of the filtration.

Terminals 5 and 6 shall be connected to the terminals of the filtration timer (see attached diagram). Every hour, the

contact between 5 and 6 is going to be closed, starting up the filtration for 5 minutes. If after 5 minutes, the

temperature of the water is over the required temperature, the filtration shuts off for one more hour. Otherwise, the

filtration and the heat pump are going to keep on operating until the desired temperature is reached. By this mean,

the user is sure the water is always ready for bath, at day or at night.

If this option is not used, the heat pump will operate only while the filtration runs.

Configuration of supply terminal

I

n three-

p

hase 400V 50Hz with neutral +

p

hase + earth

Configuration of supply terminal

I

n sin

g

le

p

hase 230V 50Hz with neutral +

p

hase + earth

Factory-fitted shunt Factory-fitted shunt

12

• It is possible to connect a remote control module (1) (with display) . To do this use terminals :

34-35 (signals Tx-Rx) and 36-37 for 12 Vac supply of the interface A1 card.

Important :

To connect the remote On/Off(2) functions, fault and warning functions for filter start up, use cables with a section of at least

1mm². Packing glands and cable inlets are available for passage of these cables into the unit.

To connect the remote module(1) (max. distance = 50 m) use a shielded cable of 4x0.75 mm² minimum (connected to the earth

harness in the heat pump).

(1) module available as an optional extra.

(2) it is essential to use an independent cable for connection of this function (terminals 1 and 2).

5. REGULATOR OPERATION

5.1 Presentation

The Euro α FK setting thermostat with digital display is supplied fitted in the appliance, electrically connected and pre-

set in the factory for swimming pool heating.

Setting principle: a control sensor placed at the water inlet side of the heat pump measures the temperature in the pool

and compares it to the target temperature. If the water temperature becomes or is lower than the target temperature, the

regulator unit authorises heating after a set time of 180 seconds, the Led blinks and then remains on.

Heating mode

Defrost cycle

(blinking = timer)

Program temperature or set

regulator parameters

On/Off (1), Stand-by (1)

(red dot), Fault reset

Increase value (UP)

Decrease value (DOWN)

Compressor operation

(blinking = timer)

Filter pump control/heat pump on

(if connected)

Temperature display in

°C or °F

(1) Stop operation in Heating mode.

Remarks :

- when a defrost cycle is in progress, it ends and ventilation is maintained with the compressor ON unless filtering is switched off (J1 open) or if SD2 < -8°C.

- in the case where the unit requests heating (Leds and on or on and blinking) led remains on (contact 5-6 closed) for 120 s then switches

off (contact 5-6 open).

or

Attention !

Incorrect connection of terminals 1-2-0-4-5-6 could result in damage

to the regulator and cancellation of the guarantee.

Filter timer

Terminal rail

in heat pump Contactor

Filter pump

Phase

Neutral

Fault indicator 230 Vac

Remote On/Off switch

Independent cable

13

5.2 Setting the target temperature

Press and hold the key to display the target temperature, press the key to increase or to decrease the

temperature. Then release both keys to return to the display of the water temperature.

Note:

The maximum target temperature is limited to 30°C in order to protect the swimming pool liner. This high target may,

however, be modified by the installer, but at his own responsibility .

6. STARTING UP

* Technical characteristics:

Tair = -3°C ; Twater = 24°C

Power

restored Power

drawn Current

drawn Throughput

Edenpac D KW KW A m3/h

4 9,5 3,67 19 6,4

5 10,9 4,21 7,6 6,4

6 13,3 4,53 7,9 7,2

Tair = 7°C ; Twater = 24°C

Power

restored Power

drawn Current

drawn Throughput

Edenpac D KW KW A m3/h

4 11,5 3,35 17,3 6,4

5 12,9 3,78 7 6,4

6 15,1 4,12 7,5 7,2

Tair = 15°C ; Twater = 24°C

Power

restored Power

drawn Current

drawn Throughput

Edenpac D KW KW A m3/h

4 14,77 3,15 16,3 6,4

5 16,05 3,29 6,4 6,4

6 20,7 3,82 7,3 7,2

• Appliance protection index: IP 24.

• Refrigerant gas type: R410A.

• Manufacturer's gas fill value:

EdenPac 4 D 1-ph. = 1500 g. EdenPac 5 D 3-ph. = 1500 g. EdenPac 6 D 3-ph. = 3000 g.

Appliance Max.

current consumed Acoustic

power Acoustic power

at 10 m Net

weight

EDENPAC 4 D

Single phase 20 A 68 dBA 40 dBA 95 kg

EDENPAC 5 D

Three phase 8 A 70,6 dBA 42,6 dBA 100 kg

EDENPAC 6 D

Three phase 9 A 71,7 dBA 43,7 dBA 132 kg

 then Ô  then Ò

14

* Heat pump operating conditions:

• The outside temperature must be higher than -8°C (automatic shut-off by anti-frost sensor SD2) and below +38°C.

• A sufficient water flow must pass into the heat pump.

Note:

The heat pump stops heating the pool water when it starts a defrost cycle by inverting the cycle.

A defrost cycle is started (Led «defrost cycle» on) when the defrost sensor SD3 (located in the cooling circuit) detects a

temperature of less than -5°C and a minimum time between two defrost cycles has been attained or when the regulator is

switched on. If the time between cycles has not been attained (with SD3 < -5°C) the Led «defrost cycle» is blinking.

- Reminder: during the defrost cycle a steam cloud (water vapour) may appear from the back of the unit (after a defrost cycle,

when the fan(s) are restarted. This cloud is evacuated to the back of the unit).

- This unit is equipped with a titanium heater condenser/unit heater anti-frost system controlled by an anti-frost sensor

(SD2) connected to a regulator (rA displayed during operation).

ATTENTION !

This titanium condenser/unit cooler anti-frost safety device is only functional

when the unit’s electrical power supply remains switched on (tjs regulator on or in stand-by).

6.1 Check

• that the hydraulic connections are correctly tightened.

• that there is no water leak.

• that the appliance is stable (with a level gauge and spirit level).

• that the cables are correctly connected to their terminals. Incorrectly tightened cables may cause overheating of

terminals.

• that the cables cannot be damaged by sharp metal sheets or elements.

• the earth connection.

• that no tools or other objects have been left inside the appliance.

6.2 Start up the heat pump

• Switch on the heat pump power supply protection device located inside the filter control cabinet.

• Start filtration.

• Set the by-pass and setting valves* as follows:

- Valve V1 slightly closed to increase the filter pressure from 150 to 200g (0.15 to 0.20 bar).

- Valve

V2 fully open.

- Valve

V3 fully open.

- Valve

V4 fully open.

- Valve

V5 half closed.

* see paragraph 4.2.

If the valves (V4 & V5) are not present, set valve V2 to fully open and valve V3 to half closed.

• Check that the swimming pool water hydraulic circuit has been vented.

• Start the heat pump if it is in stand-by mode (red dot) by pressing , ON appears on the display for a period of

5 s before displaying the water temperature.

• Set the target temperature ( + or ) => if the pool should be heated: Led blinks and then

remains on after approx. 2 to 3 minutes max. and the heat pump starts.

SD3 Ò 2°C

Start defrost

cycle

- Fan OFF

- Compressor OFF

- 4-way valve ON

60’’

Defrost cycle in

progress

- Fan OFF

- Compressor ON

- 4-way valve ON

End of defrost

cycle

- Fan OFF

- Compressor OFF

- 4-way valve OFF

60’’

Operation in

heating mode

- Fan ON

- Compressor ON

- 4-way valve OFF

ON = supplied OFF = not supplied

15

5 min. after re-start of the heat pump (fan + compressor), check the water flow pressure gauge display and set valve V3 or

V5 in order to bring the needle into the green zone (beginning of season {cold water}: position at the start of the green zone).

Reminder: If, when setting the by-pass and setting valves, the flow rate is less than 1.5 m3/h the heat pump will not

function (the flow switch remains open and the regulator displays the message AId alternating with the water temperature). Adjust the setting

valves : -V5- (if present) or -V3- and -V1-.

When the heat pump is running :

-If the flow rate switch switches on or off for a period longer than or equal to 3 s, a timer of 130 seconds* min. is

activated before the unit starts again.

* For information this time period may increase during a defrost cycle or if the compressor stop time is less than 180 s.

-In case of a power failure, a timer of 125 seconds starts when the power supply is restored before the unit starts again.

Observation: When the water attains the target temperature (Leds and off) the heat pump switches off

automatically.

Reminder:

The 3-phase heat pump is equipped with a phase order control system (KA1) used to check that the phase order is correct

at start up (and during operation) and to signal a phase order fault (regulator indicates dCP fault and the green led KA1

inside the unit is off. The orange led remains on as long as phase L1 is present). In that event, switch off and isolate the

unit and it is sufficient to invert two phase wires directly on the main supply terminal.

ATTENTION ! this operation must be carried out by a qualified and authorised professional

6.3 Checking

Check that the heat pump stops heating when:

• the target temperature on the digital display thermostat is decreased.

• filtration is switched off or valve V2 or V4 closed.

6.4 Troubleshooting

Faults :

Message Designation Cause Remedy Reset Alarm

Control sensor fault Sensor defective or

disconnected Replace or reconnect the sensor

Cut power supply or press

button if dSr starts

blinking

YES

(terminals 0-4)

Anti-frost sensor fault Sensor defective or

disconnected Replace or reconnect the sensor

Cut power supply or press

button if dSA starts

blinking

YES

(terminals 0-4)

Defrost sensor fault Sensor defective or

disconnected Replace or reconnect the sensor

Cut power supply or press

button if dSd starts

blinking

YES

(terminals 0-4)

Low pressure fault in

refrigerating circuit Insufficient refrigerant Consult a PSA-approved technician to

look for leaks and refill refrigerant

Automatic

(if less than 4 faults within an

hour) or by pressing the button

if dbP starts blinking

YES

- if more than 4

faults within one

hour -

(terminals 0-4)

High pressure fault in

refrigerating circuit

1- Water and air mixture

passing in the appliance

2- Refrigerant overload

1- Purge hydraulic circuit

2- Consult a PSA-approved technician

to check the refrigerant level

Automatic

(if less than 4 faults within an

hour) or by pressing the button

if dHP starts blinking

YES

- if more than 4

faults within one

hour -

(terminals 0-4)

Normal position of the pressure

gauge needle when the appliance is

off (compressor and fan(s) OFF).

Attention ! this position may vary

slightly in the « ARRET » zone

depending on water and ambient air

tem

p

eratures.

Normal position of the pressure

gauge needle when the

appliance is in operation

(compressor and fan(s) ON).

The position range in the

«CORRECT » zone may vary

depending on water and ambient air

temperatures, or even attain the

«LOW » zone when the water flow

going into the unit is too low.

Info: led remains on for 120s after a fault is indicated (except in the case of a dC indication when the heat pump remains operational).

16

The states:

6.5 Complete shutdown for storage

• Switch off the heat pump.

• Close the valves V2 and V3 of the BY-PASS.

• Open valves V4 and V5 next to the unit (if present).

• Drain the water condenser (RISK OF FROST) by unscrewing the two pool water inlet and outlet unions on the

side of the heat pump.

• Lightly retighten the two unions to avoid any risk of foreign bodies entering the condenser.

• Do not hermetically seal the unit (risk of condensation). A special-purpose ventilated cover is available (optional

accessory provided by PSA).

Incorrect preparation for prolonged shut-down automatically renders the WARRANTY nil and void.

Phase failure

synchronisation fault

Occurs when the 230VAC

network looses its 100 Hz

synchronisation with the

phase failulre module (A2)

Contact a PSA approved technician to

locate the cause for this fault:

- a defective module or no 230VAC

supply.

- A bad or broken electrical connection

between the regulator and module (see

connector J1 on A2 terminals 36-37-38)

Automatic

(as soon as the 100 Hz

synchronisation on the

230VAC supply is restored)

YES

(terminals 0-4)

Phase order fault (only on

three-phase heat pumps)

1- Incorrect wiring at unit

supply terminals

2- Modification of phase

order by electrical supplier

3- Temporary failure of one

or several phases

1- Check wiring at unit supply terminals

2- Contact your local electricity supplier

to ensure no modifications have been

made to your supply

Cut power supply or press the

button if dCP starts

blinking

YES

(terminals 0-4)

Defrost cycle Time Out Incorrect signal from the

defrost sensor or defrost cycle

too long (> one hour)

Consult a PSA-approved technician to

check the sensor and operation of the

defrost cycle.

Cut power supply or press the

button if dtd starts

blinking (after stand by ‘Ofr5

=> .’ and switch the regulator

on again by pressing )

YES

(terminals 0-4)

EEPROM fault Incorrect parameter data in

the regulator EEPROM Consult a PSA-approved technician to

replace the regulator Cut off power YES

(terminals 0-4)

Connection fault

Remote control module

(optional) incorrectly

connected or declared present

for the regulator but in reality

absent

Consult a PSA-approved technician and

refer to the installation instructions of

the remote control module Automatic NO

Message Designation Cause Remedy Reset Alarm

Flow switch open for

more than 3 s.

1- Filter pump is off (filter

timer is outside the

operating time limit)

2- Insufficient water

flowing through the unit

3- Flow controller

damaged or disconnected

1- Wait for the programmed filter time

period

* Test possible in mode : filtration

« manual »

2- Adjust the BY-PASS

* Filtration on

3- Change or reconnect the flow controller

Automatic after timer NO

Remote control ON/OFF.

Remote control on OFF

(Contact open)

1- Switch the remote control to ON

(Contact closed)

2- Contact a PSA-approved technician to

check the cable linking the remote control

box to the unit

Automatic NO

Anti-frost safety triggered Outside temperature too

low (< à -8°C) Wait for natural rise of outside

temperature Automatic NO

Anti-frost protection

heater is on

Outside temperature too

low (< +3°C) with

compressor OFF or

paused

Wait for natural rise of outside

temperature or for compressor to restart. Automatic NO

Info :led remains on for 120s after the status signal (except

in the case of a defrost cycle with the remote On/Off function

(Cad) and SD3 < 2°C with 4-5-6D).

: Example of the pool

water temperature display.

: Alternating

17

7. MAINTENANCE INSTRUCTIONS

Tasks to be carried out by a qualified and authorised person:

The following operations must be carried out at least once a year:

• Clean the evaporator at the back of the heat pump (with a soft brush and gentle water spray).

- Never use a high-pressure cleaner for this operation -

• Check the settings.

• Check safety devices.

• Check the presence of refrigerant (check the pressure gauge needle with the compressor switched off).

• Check electrical connections and terminals (retighten the supply cable terminals).

• Check earth connections.

• Check sealing of the cooling circuit on the EdenPAC 6D.

• Do not use solvents to clean the outside of your unit, PSA NET offers an optional specific cleaning kit.

IMPORTANT

Before working on the appliance, ensure that the power supply is disconnected and secured. All interventions must be carried

out by persons who are qualified and authorised to work on this type of equipment .

8. RECYCLING THE PRODUCT

Please refer to the paragraph with the symbol at the end of the instructions.

18

9. ELECTRICAL DIAGRAMS

9.1 Electrical diagram of connection interface card.

To J11 and J12

To J6 and J14

Phase failure module 500W

J1 : 36 – input 12Vdc

37 – output 100Hz

38 – input FAN

J2 : 39 – input Phase 230Vac

40 – input Neutral 230Vac

J3 : 41 – output Neutral 230Vac

42 – output Phase 230Vac

La page charge ...

Zodiac Edenpac 5D Instructions For Installation And Use Manual

Zodiac Edenpac 5D Instructions For Installation And Use Manual

dans d''autres langues

Autres documents