ELECTRIC HEAVY-DUTY
IMMERSION CIRCULATOR
Installation and Operating Instruction Manual
BEFORE OPERATING ANY EQUIPMENT, READ AND FAMILIARIZE YOURSELF WITH THESE USE AND SAFETY INSTRUCTIONS
Congratulations on your purchase of this SPECTRUM commercial equipment. When used as intended, and with
proper care and maintenance, you are sure to experience years of reliable operation from this equipment. To ensure
best results, it is important that you read and follow the instructions in this manual carefully. It is important to
keep these instructions in a safe place for future reference.
Model Voltage Power Amperage Plug Ty pe
Overall Dimensions Product
Weight
Length Depth Height
ESVI-1800 110-120V~60Hz 1800W 15A NEMA 5-15P 8-7/8"
(174mm)
4-1/2"
(112mm)
13"
(328mm)
6.8 lbs
(3.1 kgs)
*NEMA 5-20P (Canada)
* For Canada optional NEMA 5-20P cord and plug is required (Item No. ESVC-P17)
Form No. ESVI-1800 Manual - 11/22
ESVI-1800
ESV-IB
ESV-BH
Oponal Accessories
ESV-BH Mul Ring Bag Stand
ESV-IB Sous Vide Insulaon Balls
For California Customers
WARNING: Cancer and Reproducve Harm -
www.P65Warnings.ca.gov
2
Electric Heavy-Duty Immersion Circulator
Important For Future Reference
Introduction
Congratulations on the purchase of your SPECTRUM™ Commercial
Equipment. Please take time to carefully read through this manual to
ensure the machine is operated and maintained properly, to ensure the
best possible performance from the product for many years.
SPECTRUM will not accept liability for the following if:
• The instructions in this manual have not been followed correctly.
• Non-authorized personnel have tampered with the machine.
• Non-original spare parts are used.
• The machine has not been handled and cleaned correctly.
• There is any use damage to the unit.
Immediately Inspect for Shipping Damage
All containers should be examined for damage before and during
unloading. The freight carrier has assumed responsibility for its safe
transit and delivery. If equipment is received damaged, either apparent
or concealed, a claim must be made with the delivering carrier.
A. Apparent damage or loss must be noted on the freight bill
at the time of delivery. It must then be signed by the carrier
representative (Driver). If this is not done, the carrier may refuse
the claim. The carrier can supply the necessary forms.
B. If concealed damage or loss is not apparent until after equipment
is uncrated, a request for inspection must be made to the carrier
within 15 days. The carrier should arrange an inspection. Be certain
to keep all contents and packaging material.
Please complete this information and retain this manual for the life of the equipment. For
Warranty Service and/or parts, this information is required.
Model Number Serial Number Date Purchased
! !
WARNING: IMPROPER INSTALLATION, ADJUSTMENT,
ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE
PROPERTY DAMAGE, INJURY, OR DEATH. READ THE
INSTALLATION, OPERATION, AND MAINTENANCE
INSTRUCTIONS THOROUGHLY BEFORE INSTALLING
OR SERVICING THIS EQUIPMENT.
AVERTISSEMENT: TOUTE INSTALLATION, RÉGLAGE,
MODIFICATION, RÉPARATION OU ENTRETIEN
INCORRECT PEUT OCCASIONNER DES DOMMAGES
MATÉRIELS, DES BLESSURES GRAVES OU LA MORT.
LIRE LES INTRUCTIONS D'INSTALLATION, D'UTILISATION ET
D'ENTRETIEN ATTENTIVEMENT AVANT D'INSTALLER OU DE
RÉPARER CET APPAREIL.
! !
CAUTION: THESE MODELS ARE DESIGNED, BUILT, AND
SOLD FOR COMMERCIAL USE ONLY. IF THESE MODELS
ARE POSITIONED SO THE GENERAL PUBLIC CAN USE
THE EQUIPMENT, MAKE SURE THAT CAUTION SIGNS,
WARNINGS, AND OPERATING INSTRUCTIONS ARE
CLEARLY POSTED NEAR EACH UNIT SO THAT ANYONE
USING THE EQUIPMENT WILL USE IT CORRECTLY AND
NOT INJURE THEMSELVES OR HARM THE EQUIPMENT.
ATTENTION: CES MODÈLES SONT CONÇUS, FABRIQUÉS,
ET VENDUS POUR UN USAGE COMMERCIAL SEULEMENT.
SI CES MODÈLES SONT PLACÉS POUR QUE LE GRAND
PUBLIC PUISSE LES UTILISER, ASSUREZ-VOUS QUE LES CONSIGNES
D’ATTENTION, D'AVERTISSEMENT, ET LES INSTRUCTIONS
D'UTILISATION SOIENT CLAIREMENT AFFICHÉES PRÈS DE
CHAQUE UNITÉ DE SORTE QUE N'IMPORTE QUEL UTILISATEUR DE
L'APPAREIL L'EMPLOIE CORRECTEMENT ET NE SE BLESSE PAS OU
N'ENDOMMAGE PAS L'APPAREIL.
! !
WARNING: A FACTORY AUTHORIZED SERVICE
PROVIDER SHOULD HANDLE ALL MAINTENANCE
AND REPAIR. BEFORE DOING ANY MAINTENANCE
OR REPAIR, FOLLOW SERVICE SET UP ARRANGEMENT
ON PAGE 11.
AVERTISSEMENT: UN TECHNICIEN AUTORISÉ PAR
L'USINE DEVRA EFFECTUER TOUT L'ENTRETIEN ET LES
RÉPARATIONS. AVANT DE FAIRE TOUT ENTRETIEN OU
RÉPARATION, VEUILLEZ CONTACTER WINCO.
3
Electric Heavy-Duty Immersion Circulator
Table of Contents
Specifications .............................................................................. 1
Warnings ..................................................................................... 2
Introduction ................................................................................ 2
Packaging .................................................................................... 3
Installation .................................................................................. 4
Operation .................................................................................... 5
Cooking Chart Guide .................................................................. 7
Cleaning, Care & Maintenance ................................................. 8
Safety ........................................................................................... 9
Electrical Diagram....................................................................... 9
Troubleshooting ....................................................................... 10
Service & Repair ........................................................................ 10
Exploded View ..........................................................................11
Spare Parts List ...........................................................................11
Limited Warranty ..................................................................... 12
Package Contents
All units come with an Operating Instruction Manual and the following:
• (1) SPECTRUM™ Commercial Immersion Circulator
WINCO prides itself on quality and service, ensuring that at the time of
packing, all products are supplied fully functional and free of damage.
Should you nd any damage as a result of freight, please contact your
WINCO dealer immediately.
Unpacking the Equipment
DISPOSE OF ALL PACKAGING MATERIALS IN AN
ENVIRONMENTALLY RESPONSIBLE MANNER.
1. Remove all packing materials and tape, as well as any protective
plastic and cardboard, from the unit.
2. Clean any glue residue left over from the plastic or tape.
3. Place the unit in the desired position and height.
Please keep this manual in a safe place for future use!
Thoroughly read, understand, and follow these instructions before installation and use.
NOTE
Please remember that this manual and the warning labels do not replace the need to be alert, to properly train and
supervise operators, and to use common sense when using this equipment.
4
Installation
These instructions should be followed at all times. Failure to follow
these instructions could result in injury to yourself and others.
TO REDUCE RISK OF INJURY OR DAMAGE TO THE UNIT:
Read this manual thoroughly before installation and operation. DO NOT
proceed with installation and operation if you have any questions or do
not understand anything in this manual. Contact your representative or
the manufacturer rst.
1. Remove the SPECTRUM™ Commercial Immersion Circulator from
packaging. Be certain that all protectives plastics and residues are
thoroughly cleaned from its surfaces.
2. Select water bath container (not included) that is rated for
temperatures of 212°F(100°C), and please ensure the water level
is between the minimum and maximum water level after food
product displacement.
3. Place water bath container on a rm level surface.
4. Hang the Immersion Circulator into water bath container and
tighten the Clamp Handle to secure in place.
5. Proper connections and power supply are essential for ecient
performance. Supply the appropriate power and connect to source;
your Immersion Circulator is now ready to turn on and operate.
(For power supply please see technical specication on page 1).
Fournir l'alimentation secteur appropriée et brancher l’appareil à la
source d'alimentation ; votre Circulateur d'immersion est maintenant
Do not position or operate near combustible materials/ammable
objects.
Ne pas placer ni faire fonctionner l'appareil près de
matériels combustibles ou d'objets inflammables.
CAUTION
ATTENTION
Fire Hazard.
Correct installation precautions,
procedures and regulations
must be followed. Operation
and safety training is necessary
for all users of this equipment.
Risque d'incendie
La surchaue des vapeurs d'huile ou de
l'huile peut s'enammer et provoquer
un incendie. Surveillez la température,
la qualité et le niveau d’huile. Utilisez et
entretenez le système d'élimination des
vapeurs d'huile.
The equipment must be
installed by qualied personnel
only. Correct installation
precautions, procedures and
regulations must be followed
in order to reduce the risk of
re. Hood and re suppression
systems must be maintained
per manufacturer's guidelines.
Only qualied and trained
personnel are to use this
equipment.
Faire chauer l'huile avec précaution. Si
l'huile fume, réduire le feu. Ne pas laisser
l'appareil sans surveillance. Si le feu se
produit, éteindre l'appareil, couvrir jusqu'à
refroidissement. Ne pas mettre l'eau dans
l'huile chaude ou enammée. Ne faites pas
fonctionner avec de l'huile sous la barre
d'huile. L’huile sale a un point d'éclair
plus bas. Remplacer l'huile sur une base
régulière. Maintenir le niveau d'huile
correct. Utiliser un système d'évacuation
de la vapeur d'huile (capot) pour réduire
l'accumulation de graisse et d'huile sur les
surfaces de paroi ou de plafond.
WARNING AVERTISSEMENT
Proper Grounding · Mise à la terre correcte
This machine is provided with a three-pronged
grounding plug. The outlet to which this plug
is connected must be properly grounded. If the
receptacle is not the proper grounding type, contact an
electrician. DO NOT, under any circumstances, cut
or remove the third ground prong from the power cord
or use any adapter plug.
Cette machine est équipée d'une che à trois broches.
La prise sur laquelle cette che est branchée doit être
correctement mise à la terre. Si la prise n'est pas le type de
mise à la terre, contactez avec un électricien. NE PAS, en
aucun cas couper ou enlever la troisième broche de terre à
partir du cordon d'alimentation ou utiliser un adaptateur.
USE A GROUNDED OUTLET
DO NOT ADD AN ADAPTOR
TO THE PLUG
UTILISER UNE PRISE AVEC MISE
À LA TERRE NE PAS AJOUTER UN
ADAPTATEUR SUR LA FICHE
Electrical Shock Hazard
Keep water and other liquids
from entering the inside of the
unit. Liquid inside the unit could
cause an electrical shock.
Risque de choc électrique
Conserver l'eau et d'autres liquides
de pénétrer à l'intérieur de l'appareil.
Liquide à l'intérieur de l'appareil pourrait
provoquer un choc électrique.
Do not spray water or cleaning
products. Liquid could contact
the electrical components
and cause a short circuit or an
electrical shock. Do not use unit
if power cord is damaged or has
been modied.
Ne pas pulvériser de l'eau ou des produits
de nettoyage. Le liquide pourrait contacter
avec les composants électriques et causer
un court-circuit ou un choc électrique.
Ne pas utiliser l'appareil si le cordon
d'alimentation est endommagé.
ou a été modié.
WARNING AVERTISSEMENT
6. The units are wired to be used with a dedicated 110-120V/AC ~ 15
amp receptacle.
7. The installation of the unit must conform to the NATIONAL
ELECTRIC CODE, ALL LOCAL ELECTRIC CODES AND ORDINANCES, AND
ALL THE LOCAL ELECTRICAL COMPANY RULES AND REGULATIONS.
Additionally, we recommend a 4" spacing surrounding the unit in
order to provide adequate ventilation.
5
Operation
Using the control panel
A
B
C
A. Current Temperature Display Screen
B. Set Temperature Display Screen
C. Time Display Screen
- Power
• When the power is turned on, the machine enters the power saving mode. In the power saving mode, press button to wake up the machine and
enter standby mode.
In standby mode, (A) displays current water temperature, (B) displays the previous set temperature, and (C) displays the last set time.
• In standby mode and working mode, press button to enter the power saving mode.
(°C / °F) - Select temperature mode
• Select Celsius or Fahrenheit temperature unit to display on machine.
Temperature/Time Setting
• Press TEMP/TIME button to toggle betweeen temperature or time setting.
• On display screen when (B) is ashing, set the desired temperature with
"" and " ".
• On display screen when (C) is ashing, the desired time can be set with
"" and " ".
• After the display screen ashes 10 times, if there is no setting operation, the machine will exit the temperature/time setting state. If you need to
reset it, press TEMP/TIME
button
again to enter the setting state.
• Press and hold the TEMP/TIME
button
for about 3 seconds, the display screen displays the time and temperature that have been set.
(START/STOP)
• In standby mode, press START/STOP
button
to start the machine.
• Press START/STOP
button
a second time to start the timer.
• Press START/STOP
button
a third time to stop the machine stop and enter standby mode.
( ) and ( ) - Adjustment buttons
• Press TEMP/TIME button to select the desired (temperature or time) to be adjusted, then use the
"" and " "
buttons to adjust to the desired
temperature or time.
Restore to factory setting
• In standby mode, press both START/STOP and
" "
buttons and hold for 3 seconds until the (B) display screen will read 60°C and the (C) display
screen will set time to 24:00. Let go of both buttons and the display screen will ash 10 times and exit the setting.
6
Operation (continued)
Operating the Immersion Circulator
1. Place the water bath container on a sturdy level surface.
2. Hang the Immersion Circulator on the side of the Thermal Circulator.
NOTE: The machine body should be immersed in the water and the
fastening hook should be facing away from the water.
3. Add water to the water bath container.
NOTE: The water level (after the food is put in) should be higher than
the "MIN" but lower than the "MAX" markings. Adjust depth of circulator
as required.
NOTE: After lling water bath container, shake the immersion circulator
gently a few times to release any air in the pump. Air-locked pumps will
make a high decibel noise and running with out pumping water may
cause damage to the pump.
4. Tighten the locking screw on hook to the water bath.
5. Insert the power cord into the socket with grounding.
6. Press button to put the machine into standby mode.
7. Press
TEMP/TIME
button and set to desired temperature and time.
8. Place the food into the water bath.
NOTE:
FOOD MUST BE VACUUM SEALED OR IN AIR TIGHT MANUALLY
SEALED BAGS.
Burn Hazard.
When in operation, the surface
of the Immersion Circulator
will be hot.
Please take extreme caution.
Risque de brûlure.
Ne touchez pas les surfaces chaudes ou
chauées liquide tout appareil chaue ou
en fonctionnement.
Burn Hazard.
Do not directly touch the liquid
to check temperature, please
use temperature display or
thermometer.
Please take extreme caution.
Risque de brûlure.
Ne touchez pas directement le liquide
pour vérier la température, veuillez
utiliser l'achage de la température ou le
thermomètre.
USE CAUTION WHEN
TOUCHING THE UNIT.
Ne touchez pas le liquide chaud
ou les surfaces de chauage
lorsque l’appareil chaue ou en
fonctionnement.
WARNING AVERTISSEMENT
HOT
9. Press the
START/STOP
button to start. When the temperature
reaches the set temperature, the machine will beep, then press
START/STOP
button, machine will count down.
NOTE: During working mode, press
START/STOP
button to PAUSE.
Press again to restart - the working time will re-count from the
beginning.
NOTE: If the vacuum-sealed bag breaks during cooking, the food may
escape the bag and block the circulating channel of the machine. In this
case, please remove the food from the tank and change to new water.
Clean the lter if it is blocked.
10. After cooking is complete, the unit will beep. Press
START/STOP
to
nish.
NOTE: The unit will beep after 20 seconds and repeat if there is
no action, and the water temperature will be kept in the preset
temperature.
11. Remove the food out of the water bath and food is ready for nal
preparations.
12. After using the Immersion Circulator, unplug the power supply and
take the unit out of the water bath.
13. Place the Immersion Circulator upright vertically. Do not lay on its side
or upside down to avoid liquids from owing back into the unit.
14. After the machine is dried and cooled down, store in a safe place.
7
Cooking Chart Guide
Temperature Thickness Time to core
Temperature
Time
(Pasteurized to Core)
CUSTARD
Créme Anglaise 179.6°F / 82°C 20 min
BEEF
Tenderloin 138°F / 59°C 2" 1 hour, 58 min 5 hours, 35 min
Rib Eye Steak 138°F / 59°C 1-1/2" 1 hour, 58 min 3 hours, 20 min
Strip Steak 138°F / 59°C 1-1/2" 1 hour, 58 min 3 hours, 20 min
Porterhouse Steak 138°F / 59°C 1-1/2" 1 hour, 58 min 3 hours, 20 min
Brisket 147°F / 64°C 48 hours 3 hours, 21 min
Veal Shank 167°F / 75°C 12-24 hours 9 hours, 3 min
LAMB
Lamb Saddle 138°F / 59°C 2-1/2" 2 hours, 16 min 3 hours, 51 min
PORK
Pork Chop 145°F / 63°C 1-3/4" 1 hour, 45 min 4 hours, 2 min
Ribs 140°F / 60°C 24-48 hours 1 hour, 6 min
POULTRY
Chicken Breast 150°F / 65°C 1" 47 min 1 hour, 36 min
Duck Breast 135°F / 57°C 1" 60 min 2 hours, 41 min
Chicken Thighs 150°F / 65°C 1-1/2" 1 hour, 20 min 3 hours, 3 min
Foie Gras 147°F / 64°C 2" 2 hours, 16 min 5 hours, 9 min
FISH
Salmon Filet 130°F / 54.4°C 1" 1 hour, 39 min 5 hours, 31 min
Cod Filet 129°F / 54°C 1" 1 hour, 39 min 3 hours, 47 min
Halibut 129°F / 54°C 1" 1 hour, 39 min 3 hours, 47 min
SHELLFISH
Shrimp/Prawns 135°F / 57°C 1" 43 min 5 hours, 21 min
Lobster 145°F / 63°C 1" 15 min 5 hours, 5 min
Scallops 135°F / 57°C 1-1/2" 1 hour, 8 min 2 hours, 29 min
VEGTABLES
Root-Whole
(Beets, Carrots, Potatoes, etc.)
190°F / 88°C 60 min
Root-Cut
(Beets, Carrots, Potatoes, etc.)
185°F / 85°C 30-40 min
Bulb-Whole
(Onions, Shallots, etc.)
194°F / 90°C 85 min
Squash-Cut 185°F / 85°C 30 min
Artichoke Hearts 194°F / 90°C 60-75 min
FRUIT
Peach Wedges 190°F / 88°C 16 min
Pear Wedges 190°F / 88°C 60 min
Apple Slicers 190°F / 88°C 40 min
EGGS IN SHELL
Soft Poached Egg 143°F / 62°C 57 min 44 min
This table is only meant to serve as a guideline. Temperatures should be adjusted to your preference of doneness.
Cooking time should be adjusted to initial temperature, heat transfer characteristics, and thickness of food being cooked.
NOTE: Times shown in this table are to achieve the absolute specied core temperature. Cook times can be reduced signicantly by adding
1° to the water bath temperature. The closer the bath temperature is to the core temperature, the longer the cooking time with be.
Raw or unpasteurized food must be never served to individuals with a weakened immune system, children, older adults and those that
may be pregnant, as there is higher risk for serious illness.
NOTE: For most accurate temperature control, be sure to place lid or Sous Vide Insulation Balls (ESV-IB, sold separately) on the vessel when in
use.
8
Care & Maintenance
To maintain the appearance and increase the service life,
clean your unit. Tap-water contains minerals. When the
water is heated to a certain temperature, there will be
scale on the heater or surface of the unit. The SPECTRUM™
Immersion Circulator should be cleaned after after every
20 uses or after 100 hours of work time; however, the unit
may require more frequent cleaning, depending on the
volume of production or due to water in your area.
We suggest changing the water after each use and fill with new
water before each use. Reusing old water will cause the mineral
in the water to scale on unit components, thus affecting the
performance of the unit.
Allow unit to cool to room temperature between water changes
and uses. Placing a hot unit into cold water may cause damage
and effect the performance of the unit.
Should reduced circulation discharge capacity be experienced,
components have become dirty, please disassemble the stainless
steel housing to clean inner components.
Cleaning (with Water Bath)
1. The Immersion Circulator should be cleaned after 20 uses or
after 100 hours, however your unit may need more depending
on volume of production.
2. Place the Immersion Circulator into the container.
NOTE: Make sure the container is over 7"(180mm) high.
3. Combine 50/50 mixture of white vinegar and water, and ll
container to the "MAX" line.
ATTENTION: If vinegar comes in contact with eyes, rinse with
lots of water. See a doctor if needed.
4. Turn on the machine. Set the working temperature to 176°F
(80°C), and working time to 3 hours (03:00). Then press
START/
STOP
. After 3 hours, the machine will beep, then press
START/
STOP
to stop machine
,
turn o the machine, and unplug and
cool down the machine.
5. Remove the lower casing of machine (remove the quick-release
screws and pull out the lower casing), use the clean water to
clean the heater and other components as well as lower casing,
so as to better clean the softened scale.
Note: Please ensure the power is disconnected and the
machine cools down before disassembling and cleaning.
6. After cleaning, dry the machine and casing, then re-install the
lower casing.
7. QUICK CLEAN PROGRAM: Press “SET” and " " at the same
time for 3 seconds, the machine will go into clean program. The
set temperature will be 176°F (80°C) and work time for 3:00.
Then press “Start/Stop”, machine will start to clean.
(Press “ ” immediately all the time when machine power
on, there will display the total working hours before cleaning,
release will be out of the view mode.)
8. Check if the machine is clean. If not, add vinegar to the
container and run the machine again as stated in the above
steps. If the machine is clean, drain the water and vinegar from
the container. Wash the machine and container with fresh
water, then dry them and store them well.
Note: The Immersion Circulator should be placed upright
after cleaning. DO NOT lay on its side or upside down.
Cleaning Inner Components
1. Switch power o, disconnect from the outlet, and let the unit cool
down to room temperature before cleaning.
2. Remove the xing screws on each side of the unit.
3. Slide down the stainless steel housing.
4. Clean inner components with soft wet cloth.
5. Let dry and assemble parts back together.
6. Store the assembled machine properly for the next use
9
Safety
Electrical Shock Hazard
Keep water and other liquids
from entering the inside of the
unit. Liquid inside the unit could
cause an electrical shock.
Risque de choc électrique
Conserver l'eau et d'autres liquides
de pénétrer à l'intérieur de l'appareil.
Liquide à l'intérieur de l'appareil pourrait
provoquer un choc électrique.
Do not spray water or cleaning
products. Liquid could contact
the electrical components
and cause a short circuit or an
electrical shock. Do not use unit
if power cord is damaged or has
been modied.
Ne pas pulvériser de l'eau ou des produits
de nettoyage. Le liquide pourrait contacter
avec les composants électriques et causer
un court-circuit ou un choc électrique.
Ne pas utiliser l'appareil si le cordon
d'alimentation est endommagé.
ou a été modié.
WARNING AVERTISSEMENT
Burn Hazard.
When in operation, the surface
of the Immersion Circulator
will be hot.
Please take extreme caution.
Risque de brûlure.
Ne touchez pas les surfaces chaudes ou
chauées liquide tout appareil chaue ou
en fonctionnement.
USE CAUTION WHEN
TOUCHING THE UNIT.
Ne touchez pas le liquide chaud
ou les surfaces de chauage
lorsque l’appareil chaue ou en
fonctionnement.
WARNING AVERTISSEMENT
HOT
SAFETY PRECAUTIONS
Before installing and operating this equipment be sure
everyone involved in its operation are fully trained and
aware of all precautions. Accidents and problems can
result from a failure to follow fundamental rules and
precautions.
• A WINCO® Approved Recommended Qualied Service Technician
should carry out repairs if necessary. Do not remove any
components or service panels on this product.
• Allow the Immersion Circulator to cool down after use before
dismantling for cleaning; the unit will be too hot to handle
immediately after use.
• Before cleaning, switch o power and disconnect power cord from
the outlet.
• Do not immerse unit in water or use hose to clean.
Ne jamais immerger l'appareil dans l'eau ni utilisez un jet
d'eau pour le nettoyer.
• If the power cord is damaged, it must be replaced by a WINCO®
Approved Recommended Qualied Service Technician in order to
avoid a hazard.
1
2
3
J1
POWER
1
2
3
L
E
N
HEATER
MAIN-PCB
1
2
3
Temperature Sensor
MM2
FAN
Low water switch
MM1
PUMP
HEATER
POWER
POWER PCB Control PCB
PUMP FAN
High water switch
DS18B20
GND
+12VDC
L1
N1
MIN-W
Thermal Link Control Heater
SF129
Heater
L
N
Heater2
R+
R-
This circuit diagram has been provided to assist qualied electricians; only SPECTRUM™
service agents or qualied electricians should carry out repairs if required.
Do not remove any components or service panels on this product.
Electrical Circuit Diagram
MODEL: ESVI1800
10
If your SPECTRUM™ Immersion Circulator does not operate, please check the following before placing a service call:
Troubleshooting
ISSUE MIGHT BE CAUSE BY RECOMMENDED SOLUTION
The unit is not working and the
display is not on
Lack of power Check main power supply
Power switch has not been turned on Check that unit is correctly plugged in and turned on
Wrong operating procedure Refer to operating instructions
Plug and lead are damaged Replace damaged power cable - Replacement must be done
by an authorized service provider
Internal wiring is faulty Call WINCO to make service arrangements through its Service
Provider Network
Water temperature does not
increase
The set temperature is below or close to the
water temperature Check the setting.
Set heating time is too short Extend the heating time.
Water continues to heat after the
set temperature is reached.
Program is wrong Restart the power switch.
Temperature sensor is faulty Replace faulty sensor - Replacement must be done by an
authorized service provider
The circulating pump is not running Remove power from the unit. Leave the unit o for 2 minutes
before resetting power.
E01 appears on the display screen
Water level is below the minimum water level
line
Add water to the cooking tank so that the water level exceeds
the minimum water level.
Machine is not in water Place the machine into water and restart the power.
E02 appears on the display screen
Heating element is faulty Call WINCO to make service arrangements through its Service
Provider Network
Internal wiring is faulty
Temperature sensor is faulty Replace faulty sensor - Replacement must be done by an
authorized service provider
Unit powers on, but no display. Display malfunction Remove power from the unit. Leave the unit o for 2 minutes
before resetting power.
High decibel noise from the pump
Air is inside the pump After lling water into the tank, shake the machine for a few
seconds to discharge the air out of the impeller of the pump.
Debris is inside the pump
Clean the machine and pump according to instruction manual
(Or call WINCO to make service arrangements through its
Service Provider Network)
Water level is not enough to reach the pump Increase water level
Service and Repair
THIS EQUIPMENT MUST ONLY BE SERVICED BY AN AUTHORIZED AGENT.
NOTE
Parts protected by the manufacturer or its agent are not to be adjusted by the installer unless the installer is an authorized service agent.
If you have any questions or problems DO NOT send unit to WINCO® without rst contacting our customer service department.
See "Limited Warranty" section on page 12 for details.
11
Exploded Views
MODEL: ESVI1800
Parts List
MODEL: ESVI1800
#Description Part #
1Pump AC/DC Converter ESVI-P15
2Control Panel Assembly ESVI-P16
3Fastening Plate and Screw ESVI-P17
4Fan ESVI-P18
5Heating Element ESVI-P19
Please contact factory for special order parts not listed.
1
9
7
8
2
3
4 5 6
#Description Part #
6Temperature Sensor ESVI-P20
7Optional NEMA 5-20P Cord & Plug
(Canada)
ESVC-P17
8Float Switch ESVI-P21
9Pump ESVI-P22
C14 Connector EGD-MP14
12
WINCO® warrants to the original purchaser of new
equipment that said equipment, when installed in
accordance with our instructions within North America
and subjected to normal use, is free from defects in
material or workmanship for a period of 1 year. The labor
warranty is one year from original installation or 18
months from actual factory shipment date, whichever
date occurs rst.
THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, WHETHER EXPRESSED OR IMPLIED.
WINCO EXPRESSLY DISCLAIMS ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR EXPRESSED
OR IMPLIED WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE.
WINCO’S OBLIGATION AND LIABILITY UNDER THIS
WARRANTY IS EXPRESSLY LIMITED TO REPAIRING
AND REPLACING EQUIPMENT THAT PROVES TO
BE DEFECTIVE IN MATERIAL OR WORKMANSHIP
WITHIN THE APPLICABLE WARRANTY PERIOD.
IN NO EVENT SHALL WINCO BE LIABLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES
TO BUYER OR ANY THIRD PARTY, INCLUDING,
WITHOUT LIMITATION, LOSS OF PROPERTY,
PERSONAL INJURY, LOSS OF BUSINESS OR
PROFITS OR OTHER ECONOMIC LOSSES, OR
STATUTORY OR EXEMPLARY DAMAGES, WHETHER
IN NEGLIGENCE, WARRANTY, STRICT LIABILITY,
OR OTHERWISE.
This warranty is given only to the rst purchaser from
a retail dealer. No warranty is given to subsequent
transferees.
Warranty does not cover product failures caused by:
failure to maintain, neglect, abuse, damage due to
excess water, re, normal wear, improper set up and use.
Periodic maintenance is not covered.
This warranty is not in force until such time as a properly
completed and digitally signed Installation/Warranty
Registration has been received by WINCO within 30 days
from the date of installation.
WARRANTY SERVICE
DO NOT send unit to WINCO® without rst contacting our customer
service department: 973-295-3899.
To initiate warranty service please visit our online portal:
https://www.wincous.com/contact-us/product-technical-support
Limited Warranty
SCAN FOR ONLINE PORTAL
If having trouble or unable to
scan, enter the web address
listed above to access the
online portal.
Please provide or have the following information available:
• Contact Name, E-mail, and Phone Number
• Company/Organization Name
• Model Number and Serial Number
• Pictures or Supporting Documentation
Proof of purchase is required to extend warranty more than 1 year from date of
shipment from the factory.
THE FOREGOING WARRANTY PROVISIONS ARE A COMPLETE AND EXCLUSIVE
STATEMENT BETWEEN THE BUYER AND SELLER. WINCO® NEITHER ASSUMES
NOR AUTHORIZES ANY PERSONS TO ASSUME FOR IT ANY OTHER OBLIGATION
OR LIABILITY IN CONNECTION WITH SAID EQUIPMENT.
Examples of items not covered under warranty, but not limited to just these items:
1. Natural disasters (ie: earthquakes, tornadoes, hurricanes, etc.), re, water
damage, burglary, accident, theft.
2. Freight damage.
3. Improper installation or alteration of equipment.
4. Use of generic or after-market parts.
5. Repairs made by anyone other than a WINCO® designated service provider.
6. Lubrication.
7. Expendable wear parts, adjustable feet, blown fuses, lamps, etc.
8. Normal product maintenance.
9. Misuse or abuse.
10. Normal wear and tear items such as light bulbs, fuses, and exterior nishes.
Warranty voided if:
1. Product is altered by user
2. Serial number plate is removed
3. Product is installed in a prison or any correctional facility.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
dans d''autres langues
- English: Spectrum ESVI-1800 User manual
Autres documents
-
Breville CSV750 Manuel utilisateur
-
-
KALORIK SVD 43056 BK Le manuel du propriétaire
-
Weston 36200 Mode d'emploi
-
Hendi iVide Plus Manuel utilisateur
-
-
Vollrath Immersion Circulator Manuel utilisateur
-
TA Instruments ARES-G2 Getting Started Manual
-
U.S. Boiler Company 8B Series spécification
-
Dash Chef Series Sous Vide Circulator Le manuel du propriétaire
