Brother QL-1060N Set Up And Operation Manual

Taper
Set Up And Operation Manual
Label Overview
STEP
1
Introduction
STEP
2
STEP
3
For Windows
®
For Macintosh
®
STEP
4
Getting started
Reference
Installing the Software
Setup & Operation Guide
Guide d'installation et de
configuration
Be sure to read and understand this guide before using the machine. We
recommend that you keep this guide nearby for future reference.
Veillez à lire attentivement et bien comprendre ce guide avant de commencer à utiliser
l’appareil. Nous vous recommandons de le conserver à portée de la main afin de
pouvoir vous y reporter en cas de besoin.
Thank you for purchasing the Brother QL-1060N.
This guide briefly describes the steps to start using the Brother QL-1060N.
See the User's Guide for details. The User's Guide can be found in the Manuals folder of
the included CD-ROM.
We strongly recommend that you read this guide carefully before using the Brother
QL-1060N, and then keep it nearby for future reference.
We provide service & support for users who register their products on our website.
We recommend that you take this opportunity to register with us by visiting us at:
Online User Registration
www.brother.ca
Online Support Page
http://solutions.brother.com/
NOTE: It is also possible to access the above sites from the online user registration
window of the included CD-ROM. We look forward to your registration.
No part of this manual may be reproduced in any form, including photocopying or
reprinting, without prior consent.
The rights and copyrights of bundled software (including but not limited to the program,
images, clip art, templates and text incorporated into the software) and attached
manuals and other documents, and any copies of the software, are owned by Brother
Industries, Ltd. and its suppliers.
Industry Canada Compliance Statement (Canada Only)
This Class B digital apparatus complies with Canadian ICES-003.
STEP
1
STEP
2
STEP
3
For Windows
®
For Macintosh
®
STEP
4
Introduction
Getting started
Reference Installing the Software
Label Overview
1
Introduction
Introduction •••••••••••••••••••••••••••••••••••••••••••••••••••• 1
Contents ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 1
General Information ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 2
Safety Precautions •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 3
General Precautions •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 5
Getting started ••••••••••••••••••••••••••••••••••••••••••••••••• 7
1 Unpacking the QL-1060N •••••••••••••••••••••••••••••••••••••••••••••••••••• 7
2 Parts Description••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 8
Main Printing Unit•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 8
3 Setting the DK Roll •••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 8
4 Connecting the Power Supply••••••••••••••••••••••••••••••••••••••••••••••• 9
5 Installing the Label Tray •••••••••••••••••••••••••••••••••••••••••••••••••••••• 10
6 Using Interface Cable ••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 10
Installing the Software •••••••••••••••••••••••••••••••••••••••• 11
Installing the Software •••••••••••••••••••••••••••••••••••••••••••••••••••••••• 11
1. When using Microsoft
®
Windows ••••••••••••••••••••••••••••••••••••••••••••••••• 11
2. When using Mac OS
®
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 17
Label Overview ••••••••••••••••••••••••••••••••••••••••••••••••• 23
1 Variety of the Labels •••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 23
2 General Procedures••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 24
3 Start P-touch Editor Help••••••••••••••••••••••••••••••••••••••••••••••••••••• 25
For Windows ••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 25
For Mac•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 26
Reference••••••••••••••••••••••••••••••••••••••••••••••••••••••• 27
Main Specifications•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 27
Accessories••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• 28
Contents
STEP1
STEP1
STEP2
STEP2
STEP3
STEP3
STEP4
STEP4
Introduction
2
Compilation and Publication Notice
Under the supervision of Brother Industries Ltd., this guide has been compiled and
published, covering the latest product’s descriptions and specifications.
The contents of this guide and the specifications of this product are subject to
change without notice.
Brother reserves the right to make changes without notice in the specifications and
materials contained herein and shall not be responsible for any damages (including
consequential) caused by reliance on the materials presented, including but not limited to
typographical and other errors relating to the publication.
The screen images in this guide can be differed depending on your OS or printer.
© 2007 Brother Industries Ltd.
Trademarks
The Brother logo is a registered trademark of Brother Industries, Ltd.
Brother is a registered trademark of Brother Industries, Ltd.
© 2007 Brother Industries, Ltd. All rights reserved.
Microsoft, Windows Vista and Windows are either registered trademarks or trademarks
of Microsoft Corp. in the United States and/or other countries.
Apple, Macintosh and Mac OS are trademarks of Apple Inc., registered in the United
States and other countries.
The names of other software or products used in this document are trademarks or
registered trademarks of the respective companies that developed them.
Each company whose software title is mentioned in this guide has a Software License
Agreement specific to its proprietary programs.
All other brand and product names mentioned in this Setup & Operation Guide and the
User's Guide are registered trademarks of their respective companies.
Symbols Used in this Guide
The symbols used throughout this guide are as follows:
This symbol shows information or directions that should be followed. If ignored, the
result may be injury, damage, or failed operations.
This symbol shows information or directions that can help you better understand and
use the machine more efficiently.
General Information
3
STEP
1
STEP
2
STEP
3
For Windows
®
For Macintosh
®
STEP
4
Introduction
Getting started
Reference Installing the Software
Label Overview
Read and understand all of these instructions and save them for later reference. Follow
all warnings and instructions marked on the product.
The symbols used in this guide are as follows:
To use the machine safely
Warning Tells you what to do to avoid the risk of injury.
Caution
Tells you about procedures you must follow to prevent damage to the machine.
Action NOT allowed to do DO NOT disassemble the product.
DO NOT splash the product with or
immerse the product in water.
DO NOT touch a given portion of the
product.
Mandatory action Unplugging
Alerts to the possibility of electrical
shock
Warning
Follow these guidelines to avoid fire, electric shock, or other damage.
The Machine
Unplug the power cord immediately and
stop using the machine during an
electrical storm. There may be a remote
risk of electric shock from lightning.
Do not touch any metal parts near the
print head. The print head becomes very
hot during use and remains very hot
immediately after use. Do not touch it
directly with your hands.
Dispose of plastic bags correctly and
keep away from babies and children. Do
not wear or play with plastic bags.
Unplug the power cord immediately and
stop using the
machine
if you notice any
abnormal odor, heat, discoloration,
deformation or anything unusual whilst the
machine
is in use or storage.
Do not disassemble the machine.
For inspection, adjustment and repair of
the machine contact the retail outlet
where the machine was purchased or
your local authorized service center.
Do not drop, hit or otherwise bang the
machine.
Do not hold and lift the machine by the
DK Roll cover. The cover could come off
and the machine could fall and become
damaged.
Do not allow the
machine
to get wet in any
way.
Do not use the machine with foreign
objects in it. If water or any foreign
objects should enter the machine,
unplug the power cord from the electric
outlet and remove the foreign object. If
necessary, contact the retail outlet
where the machine was purchased or
your local authorized service center.
Do not hold the machine with only one
hand. The machine may slip out of your
hand.
Safety Precautions
Introduction
4
Follow these guidelines to avoid fire, electric shock, or other damage.
Power Cord
Use only the authorized power source
(120V AC) for the machine.
Use only the power cord included with
the machine.
Do not handle the power cord or plug if
your hands are wet.
Do not overload the electrical outlet
sockets with too many appliances or
plug the power cord into a damaged
electrical outlet.
Do not cut, damage, alter or place heavy
objects on the power cord.
Do not use the power cord if it is
damaged.
Ensure the power cord is correctly
inserted into the electrical outlet.
If the machine will not be used for an
extended period, remove the power cord
from the electrical outlet.
Caution
Follow these guidelines to avoid fire, electric shock, or other damage.
The Machine
The electrical outlet should be close to the machine and be easily accessible.
Power Cord
Always hold the power cord when unplugging the power cord from or plugging it into
the electrical outlet. Pulling on the power cord could cause problems.
Cutter
Do not touch the blade of the cutter.
Do not open the top cover when the cutter is operating.
Installation/Storage
Put the machine on a flat, stable surface
such as a desk.
Do not put any heavy objects on top of
the machine.
DK Roll (DK Label, DK Tape)
Be careful not to drop the DK Roll.
DK Rolls use thermal paper and thermal
film. Both the label and print will fade
with sunlight and heat. Do not use DK
Rolls for outdoor use that requires
durability.
Depending on the area, material, and
environmental conditions, the label may
unpeel or become irremovable, the color
of the label may change or be
transferred to other objects.
Before applying the label, check the
environmental condition and the
material. Test the label by affixing a
small piece of it to an inconspicuous
area of the intended surface.
Warning
5
STEP
1
STEP
2
STEP
3
For Windows
®
For Macintosh
®
STEP
4
Introduction
Getting started
Reference Installing the Software
Label Overview
The Machine
Never disassemble the machine or allow it to get wet to avoid possible fire or electrical
shock. Do not unplug the power cord from or plug it into the electrical outlet with wet
hands. Doing so could cause an electrical shock or fire.
Do not touch the cutter. Personal injury could result.
The machine is a precision machine. Do not drop, hit or otherwise bang the machine.
Do not lift the machine by the DK Roll compartment cover. The cover could come off and
the machine could fall and become damaged.
The machine may malfunction if left near a television, radio, etc. Do not use the machine
near any machine that can cause electromagnetic interference.
Do not expose the machine to direct sunlight or near heaters or other hot appliances, in
any area exposed to extremely high or low temperatures, high humidity or dusty areas.
Doing so could cause the machine to malfunction.
Do not use paint thinner, benzene, alcohol or any other organic solvents to clean the
machine. Doing so may cause damage to the surface finish. Use a soft, dry cloth to clean
the machine.
Do not put any heavy objects or objects containing water on top of the machine. If water
or any foreign object enters the machine, contact the retail outlet where the machine was
purchased or your local authorized service center. If you continue to use the machine
with water or a foreign object in the machine, the machine may be damaged or personal
injury could result.
Do not insert any objects into or block the label output slot, USB port, Serial port or LAN
port.
Do not put any metal parts near the print head. The print head becomes very hot during
use and remains very hot immediately after use. Do not touch it directly with your hands.
Use only the interface cable (USB cable) included with the machine.
When not in use for an extended period, remove the DK Roll from the machine.
Do not attempt to print labels while the DK Roll cover is open.
Power Cord
Use only the power cord included with the machine.
If the machine will not be used for an extended period, unplug the power cord from the
electrical outlet.
Always hold the power cord when unplugging the power cord from or plugging it into
electrical outlet. Do not pull on the power cord. The wire in the electrical cord may
become damaged.
You should put the machine near an easily accessible, standard electrical socket.
DK Roll (DK Label and DK Tape)
Use only genuine Brother accessories and supplies (with , marks). Do not use any
unauthorized accessories or supplies.
If the label is attached to a wet, dirty, or oily surface, it may peel off easily. Before
applying the label, clean the surface to which the label will be applied.
DK Roll uses thermal paper and thermal film so that ultraviolet rays, wind, and rain may
cause the color of the label to fade and the ends of the label to peel off.
Do not expose the DK Rolls to direct sunlight, high temperatures, high humidity, or dust.
Store in a cool, dark place. Use the DK Rolls soon after opening the package.
Scratching the printed surface of the label with your finger nails or metal objects, or
touching the printed surface with hands dampened by water, sweat, or medicated cream,
etc., can cause the color to change or fade.
Do not apply labels to any persons, animals, or plants.
General Precautions
Introduction
6
As the end of the DK Roll is designed to not adhere to the label spool, the last label may
not be cut properly. If this happens, remove the remaining labels, insert a new DK Roll,
and reprint the last label.
Note: To account for this, the number of DK Labels included on each DK Roll may be
more than indicated on the package.
If a label is removed after begin applied to a surface, some portion of the label may
remain. Remove the remaining portion before attaching a new label.
Some DK Rolls use permanent adhesive for their labels. These labels cannot be easily
peeled off once attached.
Prior to using CD/DVD labels, be sure to follow the instructions in your CD/DVD player's
instruction guide regarding applying CD/DVD labels.
Do not use CD/DVD labels in a slot loading CD/DVD player, for example a CD player in
a car where the CD is slid into a slot in the CD player.
Do not peel off the CD/DVD label once it is applied to the CD/DVD, a thin surface layer
may come off, resulting in damage to the disk.
Do not apply CD/DVD labels to CD/DVD disks designed for use with ink jet printers.
Labels peel off these disks easily and using disks with peeled labels can result in loss or
damage of data.
When applying CD/DVD labels, use the applicator included with the CD/DVD label rolls.
failure to do so could cause damage to the CD/DVD player.
User's shall take full responsibility for applying CD/DVD labels. Brother accepts no
responsibility for any loss or damage of data caused by the inappropriate use of CD/DVD
labels.
CD-ROM and Software
Do not scratch or subject the CD-ROM to high or low temperatures.
Do not put heavy objects on the CD-ROM or apply force to the CD-ROM.
The software contained on the CD-ROM is meant for use with the machine only. See the
License on the CD for details. This software may be installed on multiple computers for
use in an office, etc.
7
STEP
1
STEP
2
STEP
3
For Windows
®
For Macintosh
®
STEP
4
Getting started
Reference Installing the Software
Label Overview
Introduction
Getting started
Check that the package contains the following before using the QL-1060N. If any item is
missing or damaged, contact your Brother dealer.
QL-1060N
USB cable SETUP & OPERATION GUIDE
CD-ROM DK Label & Tape Guide
AC Power cord
DK Roll (Starter roll)
The QL-1060N includes two starter rolls of :
One starter roll of DK Die-cut
4" X 6" (102mm × 152mm) Labels
One starter roll of DK Continuous Paper Tape
2-3/7" (62mm)
Warranty Card
Label tray
1 Unpacking the QL-1060N
STEP1 Getting started
8
Front Rear
1
Press and hold the ON/OFF button to turn
the QL-1060N off. Pull up the left and right
levers on the machine under the top cover,
and open the cover.
2
Put the spool into the spool guides in the DK
Roll compartment.
Make sure that the spool arms are inserted firmly in
the spool guides on the left and right.
Insert the spool with the DK Roll located on the right
hand side of the QL-1060N.
2 Parts Description
Main Printing Unit
FEED button
LED lamp
ON/OFF button
CUT button
DK Roll compartment cover
Power cord
USB port
LAN port
Serial port
3 Setting the DK Roll
9
STEP
1
STEP
2
STEP
3
For Windows
®
For Macintosh
®
STEP
4
Getting started
Reference Installing the Software
Label Overview
Introduction
Connect the power cord to the
QL-1060N and then plug the power
cord into a electrical outlet.
Check that the electrical outlet is 120V
AC before plugging the power cord.
Unplug the power cord from the
electrical outlet after you have finished
using the QL-1060N.
Do not pull the power cord when
unplugging it from the electrical outlet.
The wire in the power cord may
become damaged.
Do not connect the QL-1060N to the
computer until directed to do so when
installing the printer driver.
3
Thread the end of the DK Roll into
the slot until it can be seen from the
other side.
When unable to thread the end of the
DK Roll into the slot, thread it as far as
possible, and then close the cover.
Press the ON/OFF button to turn the
QL-1060N on, and then press the
FEED button to set the roll.
4
Close the DK Roll compartment cover until it
clicks right and left side.
4 Connecting the Power Supply
STEP1 Getting started
10
The machine contains a label tray
which can hold up to 10 individual
label sheets.
As shown right, install the label tray
to the front face of the machine.
When printing more than 10 labels
continuously using the auto cut
function, remove the paper guide to
prevent a paper jam.
RS-232C cable and Network cable are not standard accessories.
Prepare the appropriate cable for your interface.
USB cable
Use the enclosed interface cable.
RS-232C cable
Do not use an interface cable that is longer than 6 feet (2.0 meters).
For details, see Appendix-Serial Cables of User’s Guide.
Network cable
Use a straight-through Category5 (or greater) twisted-pair cable for 10BASE-T or
100BASE-TX Fast Ethernet Network.
Important
The enclosed interface cable should be used in order to ensure
compliance with the limits for EMC.
A shielded interface cable should be used in order to ensure compliance
with the limits for EMC.
Changes or modifications not expressly approved by Brother Industries,
Ltd. could void the user's authority to operate the equipment.
Caution for LAN connection
Connect this product to a LAN connection that is not subjected to overvoltages.
Caution for RS-232C connection
The RS-232C serial connector part of this equipment is not Limited Power Source.
5 Installing the Label Tray
6 Using Interface Cable
11
STEP
1
STEP
2
STEP
3
For Windows
®
For Macintosh
®
STEP
4
Getting started
Reference Installing the Software
Label Overview
Introduction
Installing the Software
This section explains how to install the P-touch Editor 5.0, P-touch Address Book 1.1,
Printer Driver, and User's Guide as a whole.
The procedure for installing them varies depending on the OS of the computer.
The following is the example for Windows Vista
®
.
Install procedure is subject to change without notice.
1
Start the computer and put the CD-ROM into the CD-ROM drive.
If it does not start up automatically, open the files on the CD-ROM and double
click on "Setup.exe".
2
Click "Standard Installation".
Installation items:
Standard Installation
P-touch Editor 5.0,
P-touch Address Book 1.1,
Printer Driver, User's Guide (PDF),
and Network User's Guide (PDF)
Custom Installation
P-touch Editor 5.0, P-touch
Address Book 1.1, Printer Driver,
User's Guide (PDF), and Network
User's Guide (PDF)
Utility Installation
BRAdmin Light
User's Guide
User's Guide (PDF), Network User's Guide (PDF), and link to the download
page for Adobe
®
Reader
®
.
3
Read the license agreement and click [Yes] if you agree with the
terms and conditions.
4
Follow the on-screen instructions.
Installing the Software
1.
When using Microsoft
®
Windows
1
2
3
4
1
2
3
4
STEP2 Installing the Software
12
5
Put a check mark in the box to install the
Add-in and click [Next].
Make sure that you closed all Microsoft
®
Office
®
applications.
For details on the Add-in, see the "User's
Guide (PDF)".
6
Click [OK].
Then, choose your connection method and click [Next].
For USB interface cable users
7-1
Choose Local Printer with USB cable
and click [Next].
7-2
Follow the on-screen instructions. When
this screen appears, make sure to turn
on the power. Connect the USB interface
cable to your computer, and then
connect it to the machine.
Now, go to step 8 on page 14.
13
STEP
1
STEP
2
STEP
3
For Windows
®
For Macintosh
®
STEP
4
Getting started
Reference Installing the Software
Label Overview
Introduction
For Network interface cable users
For shared network printer users
7-1
Choose Brother Peer-to-Peer Network
Printer, and then click [Next].
Check that LAN cable and the machine are
connected.
7-2
Choose Search the network for devices
and choose from a list of discovered
devices (Recommended). Or enter your
machine’s IP address or its node name.
Click [Next].
You can find your printer's IP address and the
node name by printing out the Printer Settings
Page, please refer to the NETWORK USER'S
GUIDE for details.
7-3
Choose your printer.
Now, go to step 8 on page 14.
7-1
Choose Network Shared Printer, and
then click [Next].
Check that LAN cable and the machine are
connected.
STEP2 Installing the Software
14
For details on software, see Î"User's Guide (PDF)".
You can find the User's Guide (PDF) by clicking [Start]-[ALL Programs (Programs)]-
[Brother P-Touch]-[Manuals]-[QL-1060N User's Guide (English)].
7-2
Choose your printer's queue, and then
click [OK].
Contact your administrator if you do not know
the location or the name of the printer in the
network
8
Click [Next].
If you choose "Yes, display the page", you will go to the online user registration
page before finishing the installation. (recommended)
If you choose "No, do not display the page", you will continue the installation.
9
Click [Finish].
10
Start the software.
Click [Start] - [All Programs (Programs)] - [Brother P-touch] - [P-touch Editor 5.0]
to start P-touch Editor.
Click [Start] - [All Programs (Programs)] - [Brother P-touch] - [P-touch Address
Book 1.1] to start P-touch Address Book.
15
STEP
1
STEP
2
STEP
3
For Windows
®
For Macintosh
®
STEP
4
Getting started
Reference Installing the Software
Label Overview
Introduction
Installing the BRAdmin Light configuration utility for Windows
The BRAdmin Light is a utility for initial setup of Brother network connected devices. It
can also search for Brother products on your network, view the status and configure
basic network settings, such as IP address.
For more information on BRAdmin Light, visit us at http://solutions.brother.com.
Setting your IP address, Subnet Mask and Gateway using
BRAdmin Light
If you require more advanced printer management, use the latest Brother BRAdmin
Professional utility version that is available as a download from
http://solutions.brother.com.
If you are using Personal Firewall software, BRAdmin Light may fail to detect the
unconfigured device. In that case, disable your Personal Firewall software, try
BRAdmin Light again. Re-start your Personal Firewall software after the address
information is set.
1
Click Utility Installation.
This screen is the same screen as you
see when you insert the CD-ROM.
2
Click BRAdmin Light and follow the on-
screen instructions.
If the Windows Firewall is enabled on your PC,
the message “Do you wish to add this application
to the list of exceptions?” appears. Check your
PC environment and choose Yes or No.
1
Start BRAdmin Light. It will search for new
devices automatically.
If you have a DHCP/BOOTP/RARP server in your
network, you don’t have to do the following
operation. Because the print server will
automatically obtain its IP address.
STEP2 Installing the Software
16
2
Double-click the unconfigured device.
3
Choose STATIC for the Boot Method. Enter
the IP Address, Subnet Mask and Gateway,
and then click [OK].
4
The address information will be saved to the printer.
17
STEP
1
STEP
2
STEP
3
For Windows
®
For Macintosh
®
STEP
4
Getting started
Reference Installing the Software
Label Overview
Introduction
This section explains how to install the P-touch Editor 5.0, Fonts, Auto Format
Templates, Clip Art, and Printer Driver. After installing the Printer Driver, it also explains
how to set it for the machine.
Here explains the example of Mac OS
®
X 10.4.9.
Until the installation of printer driver is completed, do not connect the machine to
Macintosh
®
. If it has been connected to it, pull out the USB interface cable/Network
interface cable from Macintosh
®
.
When installing it, log in as the administrator.
1
Start up Macintosh
®
, and insert the CD-ROM into CD-ROM drive.
QL-1060N screen is displayed.
When it does not start up automatically, double click QL-1060N
(CD-ROM) icon.
2
Click [Mac OS X] folder and double click [P-touch Editor 5.0
Installer].
Follow the on-screen instructions.
3
After the installation is completed and
the screen shown right is displayed,
click [Done].
The installation of software is completed.
Next, install the printer driver.
4
Double click [Brother QL-1060N Driver.pkg] in [Mac OS X] folder.
Driver Installer starts up. Follow the on-screen instructions.
5
When the installation is completed and
the message "Click Restart to finish
installing the software" is displayed,
click [Restart].
Macintosh
®
is restarted.
The installation of printer driver is completed.
2. When using Mac OS
®
STEP2 Installing the Software
18
6
After restarting the computer,
connect the USB/LAN cable to the
machine.
As the caution label is put on the USB
port of the machine, remove it and
then connect the USB cable.
7
Connect the USB/LAN cable to the USB/LAN port of Macintosh
®
.
Press ON/OFF button ( ) of the machine to turn on the power.
When connecting the machine to Macintosh
®
via USB hub, it may not be
connected correctly. At that time, connect the machine directly to the USB port
of Macintosh
®
.
8
Double click the drive where Mac OS
®
X is installed, and click in
order of [Applications]-[Utilities]-[Printer Setup Utility].
For USB interface cable users
9
Click Add and choose USB at the top of the
screen (in Mac OS
®
X 10.3.9).
Choose QL-1060N from the list and click
Add again to add the printer to the Printer
Setup Utility.
For Mac OS
®
X 10.4.x, click Add and add the
printer with the BRPTUSB connection. (If you do
so, an error dialog appears when an printing error
occurs.) Set the appropriate printer name.
Now, go to step 10.
For Network interface cable users (Simple Network Configuration)
9-1
Click Add.
For Mac OS
®
X 10.3.9 users, make the
following selection.
For Mac OS
®
X 10.4.X users, go to the next
step.
Power cord
USB port
LAN port
Serial port
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61

Brother QL-1060N Set Up And Operation Manual

Taper
Set Up And Operation Manual

dans d''autres langues