ROSIERES RSTP634MC/G3 Manuel utilisateur

RSTP634MC/G3

EN-2

ENGLISH

EN-3

Rosieres

EN-4

ENGLISH

Flush installation: Feasible only if the oven is not installed

under the counter

EN-5

EN-6

ENGLISH

EN-7

EN-8

ENGLISH

• You can lock the controls to prevent unintended use (for example children accidentally turning the

cooking zones on).

• When the controls are locked, all the controls except the ON/OFF control are disabled.

Locking the Controls

Touch the pause control.

Touch the pause control “ ”.

EN-9

• it is possible to set a maximum power absorption level for the induction hob, choosing up to different

power ranges.

• induction hobs are able to limit themselves automatically in order to work at lower power level, to

avoid the risk of overloading.

Power Management Function

To lock the controls

Touch and hold the Timer “ ” and Timer ”

”

at the same time for a while.

The timer indicator will show “ Lo ”

To unlock the controls

Touch and hold the Timer “ ” and Timer ”

” at the same time for a while.

When the hob is in the lock mode, all the controls are disable except the ON/OFF , you can always turn the induction hob

off with the ON/OFF control in an emergency, but you shall unlock the hob first in the next operation.

To enter Power Management Function

Turn on the hob, then Press at the same time

the Pause key and Timer ”

”.

The timer indicator will show “ P5“ which

means power level 5。The default mode is on

7.0 。

To switch to another level

press +/- of the timer

or

There are 5 power levels, from “P1” to “p5”.

The timer indicator will show one of them.

“P1” : the maximum power is 2.5 .

“P2” : the maximum power is 3.5 .

“P3” : the maximum power is 4.5 .

“P4” : the maximum power is 5.5 .

“P5” : the maximum power is 7.0 .

EN-10

ENGLISH

k

W

k

W

k

W

k

W

k

W

k

W

You can use the timer in two different ways:

• You can use it as a minute minder. In this case, the timer will not turn any cooking zone off when the

set time is up.

• You can set it to turn one or more cooking zones off after the set time is up.

The timer of maximum is 99min.

If you are not selecting any cooking zone

Timer control

a) Using the Timer as a Minute Minder

Make sure the cooktop is turned on.

Note: you can use the minute minder even if you’re not

selecting any cooking zone.

Touch “+” the controls of the timer. The minder

indicator will start flashing and “10” will show

in the timer display.

Set the time by touching the “-” or “+” control

of the timer

Hint: Touch the “-” or “+” control of the timer

once to decrease or increase by 1 minute.

Touch and hold the “-” or “+” control of the timer to decrease

or increase by 10 minutes.

Touching the “-” and "+” together, the timer

is cancelled, and the “00” will show in the minute

display.

When the time is set, it will begin to count down

immediately. The display will show the remaining

time and the timer indicator will flash for 5 seconds.

Buzzer will beep for 30 seconds and the timer

indicator shows “- - “ when the setting time finished.

Confirmation and Exit Power Management Function

Press at the same time Pause key and Timer

”” for confirmation.

Then the hob will be turned off.

EN-11

Set one zone

Touching the heating zone slider control

Set the time by touching the or control of the timer

Hint: Touch the “-“ or “+” control of the timer

once will decrease or increase by 1 minute.

Touch and hold the ”-“ or “+”control of the timer

will decrease or increase by 10 minutes.

Touching the “-” and “+” together, the timer is cancelled, and the

“00” will show in the minute display.

When the time is set, it will begin to count down immediately. The

display will show the remaining time and the timer indicator flash

for 5 seconds.

NOTE: The red dot next to power level indicator will illuminate

indicating that zone is selected.

When cooking timer expires, the corresponding cooking zone will

be switched off automatically.

b) Setting the timer to turn one or more cooking zones off

Other cooking zone will keep operating if they are turned on previously.

EN-12

ENGLISH

c) Cancel the timer

set more zones:

The steps for setting more zones are similar to the steps of setting one zone;

When you set the time for several cooking zones simultaneously, decimal dots of the relevant cooking

zones are on. The minute display shows the min. timer. The dot of the corresponding zone flashes.

The shown as below:

(set to 15 minutes)

(set to 45 m

inutes)

Once the countdown timer expires, the corresponding zone

will switch off. Then it will show the new min. timer and

the dot of corresponding zone will flash.

The shown as right:

(set to 30 minutes)

Touch the heating zone selection control, the corresponding timer will be shown in the timer indicator.

Keep warm

Touching the heating zone slider control that you want to

cancel the timer

Touching the ”-“ and “+” together, the timer is

cancelled, and the ”00” will show in the minute

display.

Activate the Keep warm function

Touching the heating zone slider control ,

and a indicator next to

the key will flash.

Touching the keep warm control , the zone indicator show

“

|

”.

Cancel the keep warm function

Touching the heating zone slider control that you want to cancel

keep warm.

EN-13

Selection of cooking vessels

You may have a number of different cooking vessels

1. This induction hob can identify a variety of cooking vessels, which you can test by

one of the following methods:

Place the vessel on the cooking zone. If the corresponding cooking zone displays a

power level, then the vessel is suitable. If “U” flashes, then the vessel is not

suitable for use with the induction hob.

2. Hold a magnet to the vessel. If the magnet is attracted to the vessel is suitable for

use with the induction hob.

NB: The base of the vessel must contain magnetic material.

It must have flat bottom with a diameter according to the table 1 below.

3. Use only ferromagnetic cookwares made from enameled steel, cast iron or stainless

steel but compatible with induction

4. Use pans whose diameter of the ferromagnetic area (base of the pan) is in the range

of dimensions in the table below. (Table 1)

- If you use smaller pots, performance could be affected

- If you use pot with a diameter smaller than the one indicated in the table 1, pots

may not be detected

According to the dimension of the zone you can use pots of different diameters as picture

below:

Iron oil frying

Stainless steel

Iron pan

Iron kettle

Enamel

stainless steel

kettle

Enamel cooking

utesil

Iron plate

EN-14

ENGLISH

5. If the ferromagnetic part covers only partially the base of the pan, only the

ferromagnetic area will heat up, the rest of the base may not heat up a sufficient

temperature for cooking.

6. If the ferromagnetic area is not homogeneous, but presents others material such as

aluminum this may affect the heating up and the pan detection.

If the base of the pan is similar to the pictures below the pan could be not detected.

The base diameter of induction cookware

Cooking zone

1 & 2 140

160

180

2903

Minimum Maximum

Flexi zone 250

The above may vary according to the size of the pan and the material it is made from.

EN-15

395*180

EN-16

ENGLISH

EN-17

EN-18

ENGLISH

EN-19

RSTP634MC/G3

189,7

174,7

189,9

184,8

La page charge ...

ROSIERES RSTP634MC/G3 Manuel utilisateur

Ce manuel convient également à

ROSIERES RSTP634MC/G3 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents