Candy CTPSC63/E1 Manuel utilisateur

PN:16166000A24993

Candy-MC-IT7251J1-AD CI633C/E1

80G双胶纸

20210301

1、印刷颜色：胶装，单黑；

EN-0

Instructions Manual For Induction Hob

ENGLISH

Thank you for purchasing the CANDY induction hob. Please read this instruction manual

carefully before using the hob and keep it in a safe place for future reference.

CTPSC63/E1

Manuel d'instructions pour plaque à induction

FRANÇAIS

59cm

52cm

6.2cm 5.8cm

5

4

6

4

5

1. On/Off c

ontrol

2. Flexible Area control

3. Boost

4. Heating zone selection controls

5. Keylock control

6. Timer control

four

1

2

3

1. Max. 1900/2000W zone

2. Max. 1900/2000W zone

3.

4.

Glass plate

5.

Control panel

6.

12 3

6

4

7. Power / Timer

slider touch control

7

How to use

Start cooking

Touch the ON/OFF control.

After power on, the buzzer beeps

once, all displays show “–” or “– –”, indicating that the induction

hob has entered the state of standby mode.

Place a suitable pan on the cooking zone that you wish to use.

• Make sure the bottom of the pan and the surface of the

cooking zone are clean and dry.

Touching the heating zone selection control, and an indicator

next to the key will flash

Select a heat setting by touching the slider control

• If you don’t choose a heat setting within 1 minute, the

Induction hob will automatically switch off. You will need to

start again at step 1.

• You can modify the heat setting at any time during

cooking.

If the display flashes alternately with the heat setting

This means that:

• you have not placed a pan on the correct cooking zone or,

• the pan you’re using is not suitable for induction cooking or,

• the pan is too small or not properly centered on the cooking zone.

No heating takes place unless there is a suitable pan on the cooking zone.

The display “ ”will automatically disappear after 1 minute if no suitable pan is placed on it.

power up

power down

Finish cooking

Touching the heating zone selection control that you wish

to switch off

Turn the cooking zone off by touching the slider to “|”.

Make sure the displayshows”0”

Turn the whole cooktop off by touching the ON/OFF

control.

Beware of hot surfaces

H will show which cooking zone is hot to touch. It will

disappear when the surface has cooled down to a safe

temperature. It can also be used as an energy saving

function if you want to heat further pans, use the

hotplate that is still hot.

Using the Boost function

Activate the boost function

Touching the heating zone selection control.

Touching the boost control , the zone indicator show

“P” and the power reach Max.

Cancel the Boost function

Touching the heating zone selection control that you wish

to cancel the boost function

• The function can work in any cooking zone.

• The cooking zone returns to its original setting after 5 minutes.

• If the original heat setting equals 0, it will return to 9 after 5 minutes.

FLEXIBLE AREA

• This area can be used as a single zone or as two different zones, accordingly

to the cooking needs anytime.

• Free area is made of two independent inductors that can be controlled

separately.

As big zone

1.

To activate the free area as a single big zone, Touching the Flexible Area control .

2. As a big zone, we suggest the used as the follow:

Cookware: 250mm or 280mm diameter cookware (Square or Oval

cookware are acceptable)

We don’t recommend other operations except for above mentioned three

operations because it might effect the heating of appliance

As two independent zones

To use the flexible area as two different zones, you can have two choices of

heating.

(a) Put a pan on the right up side or the right down side

of the

flexible zone.

Touching the "Boost" control to cancel the Boost

function, then the cooking zone will revert to its original

setting.

(b)Put two pans on both sides

of the

flexible zone.

Notice: Make sure the pan is bigger than 12cm.

Locking the Controls

• You can lock the controls to prevent unintended use (for example children accidentally turning the

cooking zones on).

• When the controls are locked, all the controls except the ON/OFF control are disabled.

To lock the controls

Touch the lock control The timer indicator will show “ Lo“

To unlock the controls

Touch and hold the lock control for a while.

When the hob is in the lock mode, all the controls are disable except the ON/OFF

,

you can always turn

the induction hob off with the ON/OFF control in an emergency, but you shall unlock the hob first in the

next operation.

Timer control

You can use the timer in two different ways:

a) You can use it as a minute minder. In this case, the timer will not turn any cooking zone off when the

set time is up.

b) You can set it to turn one or more cooking zones off after the set time is up.

The timer of maximum is 99 min.

a) Using the Timer as a Minute Minder

If you are not selecting any cooking zone

Make sure the cooktop is turned on.

Note: you can use the minute minder at least one zone shall

be active.

Touch timer control, the “10” will show in the timer display.

and the “0” flashes.

Set the time by touching the slider control. (e.g. 5)

Touch timer control again, the “1” will flash

Set the time by touching the slider control (e.g.9), now the

timer you set is 95 minutes.

When the time is set, it will begin to count down immediately. The display will show the remaining time

Buzzer will beep for 30 seconds and the timer

indicator shows “- -” when the setting time finished.

b) Setting the timer to turn one cooking zone off

Set one zone

Touching the heating zone selection control that you want to

set the timer for.

In short time, touch timer control, the “10” will show in the

timer display and the “0” flashes.

Set the time by touching the slider control. (e.g. 5)

Touch timer control again, the “1” will flash.

Set the time by touching the slider control (e.g.9), now the

timer you set is 95 minutes.

When the time is set, it will begin to count down immediately.

The display will show the remaining time .

NOTE: The red dot next to power level indicator will

illuminate indicating that zone is selected.

When cooking timer expires, the corresponding cooking zone

will be switched off automatically.

Other cooking zone will keep operating if they are turned on previously.

The pictures shown above are for reference only, and the final product shall prevail.

set more zones:

The steps for setting more zones are similar to the steps of setting one zone;

When you set the time for several cooking zones simultaneously, decimal dots of the relevant cooking

zones are on. The minute display shows the min. timer. The dot of the corresponding zone flashes.

The shown as below:

(set to 15 minutes)

(set to 45 minutes)

Once the countdown timer expires, the corresponding zone

will switch off. Then it will show the new min. timer and

the dot of corresponding zone will flash.

The shown as right:

(set to 30 minutes)

Touch the heating zone selection control, the corresponding timer will be shown in the timer indicator.

C)Cancel the timer

Touching the heating zone selection control that you want

to cancel the timer

Touching the timer control, the indicator flash

Touch the slider control to set the timer to “00”, the timer is cancelled

Default working times

Auto shut down is a safety protection function for your induction hob. It shut down automatically if ever

you forget to turn off your cooking. The default working times for various power levels are shown in the

below table:

Power level

1 2 3 4 5 6 7 8 9

Default working timer (hour)

8 8 8 4 4 4 2 2 2

When the pot is removed, the induction hob can stop heating immediately and the hob automatically

switch off after 2 minutes.

EN-14

You may have a number of different cooking vessels

1. This induction hob can identify a variety of cooking vessels, which you can test by

one of the following methods:

Place the vessel on the cooking zone. If the corresponding cooking zone displays a

power level, then the vessel is suitable. If “U” flashes, then the vessel is not

suitable for use with the induction hob.

2. Hold a magnet to the vessel. If the magnet is attracted to the vessel is suitable for

use with the induction hob.

NB: The base of the vessel must contain magnetic material.

It must have flat bottom with a diameter according to the table 1 below.

3. Use only ferromagnetic cookwares made from enameled steel, cast iron or stainless

steel but compatible with induction

4. Use pans whose diameter of the ferromagnetic area (base of the pan) is in the range

of dimensions in the table below. (Table 1)

- If you use smaller pots, performance could be affected

- If you use pot with a diameter smaller than the one indicated in the table 1, pots

may not be detected

According to the dimension of the zone you can use pots of different diameters as picture

below:

Iron oil frying

Stainless steel

Iron pan

Iron kettle

Enamel

stainless steel

kettle

Enamel cooking

utesil

Iron plate

5. If the ferromagnetic part covers only partially the base of the pan, only the

ferromagnetic area will heat up, the rest of the base may not heat up a sufficient

temperature for cooking.

6. If the ferromagnetic area is not homogeneous, but presents others material such as

aluminum this may affect the heating up and the pan detection.

If the base of the pan is similar to the pictures below the pan could be not detected.

The base diameter of induction cookware

Cooking zone

1 120

160

210

3

Minimum Maximum

The above may vary according to the size of the pan and the material it is made from.

2

180 290

EN-19

La page charge ...

Candy CTPSC63/E1 Manuel utilisateur

Candy CTPSC63/E1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents