La page est en cours de chargement...
PRODUCT NO. 168-0174-8
WILMER 16-CUBE ORGANIZER
Parts List ............................................................................................................... 4
Before You Begin Assembly ......................................................................... 7
Step-by-step Guide .......................................................................................... 8
Technical Data .................................................................................................... 25
Troubleshooting ................................................................................................ 26
Caring for Your Item ........................................................................................ 26
Warranty ............................................................................................................... 27
Death or serious injury may occur when children climb on storage or organizer
furniture. A remote control or toys placed on the furniture may encourage a
child to climb on the furniture, and as a result, it may tip over onto the child.
• NEVER allow children to climb or play with this product.
• NEVER place toys, food, remote, etc., on top of this product.
•
ALWAYS use either the safety hardware as instructed or other wall-anchoring device.
Placing TVs on furniture that are not designed to support a television is
hazardous, which may result in injury or death.
• This product is not designed to support a television.
Overloading shelves may result in furniture that can break or sag, or tip over
which may result in injury.
• NEVER exceed the weight limits shown in the instructions.
•
Place the heavier items on lower shelves as far back from the front as possible.
• Load the bottom surfaces fi rst to avoid top-heavy furniture.
• Moving furniture that is not designed to be moved or is not equipped with
castors may result in injury or damage to furniture or personal property.
• ALWAYS unload shelves, starting with the top surfaces, before moving.
• NEVER push or pull furniture on carpet. Have a friend help lift properly to
move and/or reposition it.
• This unit must be positioned against wall.
1 personHammer
No. 2 Cross-head Screwdriver
Tip Shown Actual Size
NOTE:
A drill is not recommended; be aware
of over-drilling in order to avoid damage
WILMER 16-CUBE ORGANIZER
3Side Panel 2
ITEM DESCRIPTION THUMBNAIL QUANTITY
1Top panel 1
2Bottom panel 1
4Shelf 2
5Partition 12
6Centre shelf 1
4
WILMER 16-CUBE ORGANIZER
3
1
2
4
5
6
3
4
5
5
5
5
5
5
5
5
5
5
5
5
WILMER 16-CUBE ORGANIZER
CL-bracket 1
ITEM DESCRIPTION THUMBNAIL QUANTITY
ALong wood dowel 18
BShort wood dowel 20
DWall anchor 2
ESticker card 1
FHex key 1
I2 3/8” hex head screw 4
ITEM DESCRIPTION THUMBNAIL QUANTITY
GAdjustable leveller 6
H3 5/16” hex head screw 8
J2” pan head screw 2
K5/8” pan head screw 2
6
WILMER 16-CUBE ORGANIZER
?
7
WILMER 16-CUBE ORGANIZER
Fasten the top panel 1 to one of the side panels 3. Use two hex head screws H.
Tighten with the hex key F.
NOTE: You may want to start each screw a few turns before completely tightening
any of them.
X
H
STEP 1
1X1 3X1 FX1 HX2
X
1X
3
8
These small holes
should be here.
Surface with
more holes
Surface with
more holes
WILMER 16-CUBE ORGANIZER
Insert six short wood dowels B into the holes in top panel 1.
Push three partitions 5 onto the short wood dowels in top panel 1.
STEP 2
5X3 BX6
X
1
X
5
X
5
X
5
X
B
9
WILMER 16-CUBE ORGANIZER
Insert two short wood dowels B into the holes in side panel 3.
Push one of the shelves 4 onto the short wood dowels in side panel 3.
Insert two short wood dowels B into the edge of shelf 4.
STEP 3
4X1 BX4
X
B
X
B
X
4
X
3
10
WILMER 16-CUBE ORGANIZER
Insert six long wood dowels A into the holes in the shelf 4 and into the bottom edges
of the partitions 5.
Then, push three partitions 5 onto the long wood dowels in the shelf 4.
STEP 4
5X3 AX6
X
4
X
5
X
5
X
5
X
5
X
5
X
5
X
A
11
WILMER 16-CUBE ORGANIZER
Fasten the centre shelf 6 to the side panel 3. Use two hex head screws I. Tighten with
the hex key F.
STEP 5
6X1 FX1 IX2
X
3
X
I
X
6
12
WILMER 16-CUBE ORGANIZER
Insert six long wood dowels A into the holes in the centre shelf 6 and into the bottom
edges of the partitions 5.
Then, push three partitions 5 onto the long wood dowels in the centre shelf 6.
STEP 6
5X3 AX6
X
5
X
5
X
5
X
5
X
5
X
5
X
6
X
A
13
WILMER 16-CUBE ORGANIZER
Insert two short wood dowels B into the holes in the side panel 3.
Push shelf 4 onto the short wood dowels in the side panel 3.
Insert two short wood dowels B into the edge of shelf 4.
STEP 7
4X1 BX4
X
B
X
B
X
4
X
3
14
WILMER 16-CUBE ORGANIZER
Insert six long wood dowels A into the holes in the shelf 4 and into the bottom edges
of partitions 5.
Then, push three partitions 5 onto the long wood dowels in shelf 4.
STEP 8
5X3 AX6
X
4
X
5
X
5
X
5
X
5
X
5
X
5
X
A
15
WILMER 16-CUBE ORGANIZER
Fasten the other side panel 3 to the centre shelf 6, using two hex head screws I.
Tighten with the hex key F.
NOTE: Be sure the short wood dowels in the shelves 4 insert into the holes in the end.
Now, fasten the top panel 1 to the side panel 3, using two hex head screws H. Tighten
with the hex key F.
STEP 9
3X1 FX1 HX2 IX2
X
3X
6
X
1
X
I
X
H
16
X
4
X
4
Surface with
fewer holes
WILMER 16-CUBE ORGANIZER
Insert six short wood dowels B into the holes in the partitions 5.
Fasten the bottom panel 2 to the side panels 3, using four hex head screws H. Tighten
with the hex key F.
NOTE: Be sure the short wood dowels in the uprights insert into the holes in the bottom.
STEP 10
2X1 FX1 HX4
BX6
X
5
X
5
X
5
X
3
X
3
X
2
X
B
X
H
17
Surface with
fewer holes
WILMER 16-CUBE ORGANIZER
Completely turn six adjustable levellers G into the exact holes shown in the bottom
panel 2.
NOTE: The adjustable levellers will help stabilize your unit once standing upright.
STEP 11
GX6
X
2
X
G
18
WILMER 16-CUBE ORGANIZER
You have the option to fasten your unit end-to-wall or back-to-wall.
Follow the corresponding steps according to your choice.
STEP 12
END-TO-WALL
Steps 13-14, 17
BACK-TO-WALL
Steps 15-17
19
WILMER 16-CUBE ORGANIZER
Carefully stand your unit upright against the wall in its fi nal location.
The following instructions show your unit being fastened to a wall stud. If you are not
fastening your unit to a wall stud, go to the next step now.
1st -
Fasten the L-bracket C to the small holes on the top surface of the top panel 1
exactly as shown. Use two 5/8” pan head screws K.
2nd - Locate the centre of a stud in your wall near your unit. Mark the two holes in the
L-bracket with a pencil. Drill a 1/8” hole on the mark and into the stud in your wall.
3rd - Fasten the unit to the wall. Use two 2” pan head screws J through the L-bracket
on the top panel 1 and into the 1/8” hole.
STEP 13
20
CX1 KX2
JX2
Use the 5/8” pan head
screws through the
holes in the L-bracket
and into the top.
Mark and drill a 1/8”
hole into the wall.
X
1
X
C
/
