Ubiquiti LTU-Lite Manuel utilisateur

LTU-Lite Wall Mount Bracket Screws (Qty. 2)

Screw Anchors (Qty. 2) Zip Tie Gigabit PoE (24V, 0.5A) with

Mounting Bracket

Package Contents

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Power Cord

Installation Requirements

LTU PtMP AP, such as model LTU-Rocket

Phillips screwdriver for wall-mounting

Outdoor, shielded Category 6 (or above) cabling and shielded RJ45 connectors are

required for all wired Ethernet connections.

Surge protection should be used for all outdoor installations. We recommend that

you use two Ethernet Surge Protectors, model ETH-SP-G2, one near the device and

the other at the entry point to the building. The ETH-SP-G2 will absorb power surges

and safely discharge them into the ground.

Note: For guidelines about grounding and lightning protection, follow your

local electrical regulatory codes.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Hardware Overview

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

System LED

Ethernet Port

Reset Button

Blue Initial power-up.

Flashing White Bootup in progress.

White Ready for use.

Alternating

Blue/White

Firmware upgrade in progress.

This 10/100/1000 Ethernet port is used to connect the power and should be

connected to the LAN and DHCP server.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

To reset to factory defaults, press and hold the Reset button for more than 10

seconds while the device is powered on.

Hardware Installation

1.

2.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

3.

Wall Mount

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

1.

2.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

3.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

4.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

5.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Pole Mount

1.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

2.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

3.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Connecting Power

WARNING: The switch port must comply with the power specifications listed in

“Specifications”.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

OR

Optional

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

Accessing the Configuration Interface

1. Make sure that your host system is connected via Ethernet to the device.

2. Configure the Ethernet adapter on your host system with a static IP address on the

192.168.1.x subnet.

3. Launch your web browser and type https://192.168.1.20 in the address field. Press

enter (PC) or return (Mac).

4. Select your Country and Language. You must agree to the Terms of Use to use the

product. Click Continue.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

The LTU Configuration Interface will appear, allowing you to customize your settings as

needed.

UNMS Management

You can manage your device using UNMS, which lets you configure, monitor, upgrade,

and back up your devices using a single application. Get started at www.unms.com

Find My AP

1. Click the icon.

2. In the Wireless Settings section, change the channel bandwidth (default: 20 MHz) as

needed.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

3. Click Find AP.

4. The device will scan for nearby APs. Click Select for the appropriate AP. To run the

search again, click Scan.

Note: For example, if the AP’s channel bandwidth is set to 50 MHz and your

device is set to 20 MHz, then your device will not see that AP and you should

change the channel bandwidth on your device.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

5. Follow the on-screen instructions.

Installer Compliance Responsibility

Devices must be professionally installed and it is the professional installer’s

responsibility to make sure the device is operated within local country regulatory

requirements.

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

The Auto Output Power field is provided to the professional installer to assist in meeting

regulatory requirements.

Specifications

LTU-Lite

Dimensions 153 x 84 x 39.5 mm

(6.02 x 3.31 x 1.56")

Weight 250 g (8.82 oz)

Networking Interface (1) 10/100/1000 Ethernet Port

Enclosure Outdoor UV Stabilized Plastic

Max. Power Consumption 8.5W

Create PDF in your applications with the Pdfcrowd HTML to PDF API PDFCROWD

La page est en cours de chargement...

Ubiquiti LTU-Lite Manuel utilisateur

Ubiquiti LTU-Lite Manuel utilisateur

dans d''autres langues

Documents connexes