Sauder Shoal Creek 408920 Mode d'emploi

Need help? Visit Sauder.com to view video assembly tips or chat with a live rep.

Prefer the phone? Call 1-800-523-3987.

Share your journey!

sauder.com

Executive Desk

Shoal Creek Collection | Model 408920

Business or pleasure.

Works both ways.

NOTE: THIS INSTRUCTION

BOOKLET CONTAINS IMPORTANT

SAFETY INFORMATION.

PLEASE READ AND KEEP FOR

FUTURE REFERENCE.

English pg 1-34

Français pg 35-39

Español pg 40-44

Lot # 392369 06/20/16

Purchased: __________________

Be sure to give us a ring before

making any returns. 1-800-523-3987

Table of Contents Assembly Tools Required

Part Identiﬁ cation

Hardware Identiﬁ cation

Assembly Steps

Français

Español

Safety

Warranty

Hammer

Not actual size

No. 2 Phillips Screwdriver

Tip Shown Actual Size

Skip the power trip.

This time.

2-3

4-5

6-34

35-39

40-44

45-46

47

å While not all parts are labeled, some of the parts will have a label or an inked letter on the edge

to help distinguish similar parts from each other. Use this part identiﬁ cation to help identify similar parts.

A RIGHT END (1)

B LEFT END (1)

C3 RIGHT UPRIGHT (1)

D3 LEFT UPRIGHT (1)

D28 LARGE RIGHT DRAWER SIDE (2)

D29 LARGE LEFT DRAWER SIDE (2)

D77 DRAWER BACK (2)

D78 LARGE DRAWER BACK (2)

D132 RIGHT DRAWER SIDE (2)

D138 LEFT DRAWER SIDE (2)

D707 DRAWER BOTTOM (4)

EE3 TOP (1)

G MODESTY PANEL (1)

H RIGHT FRONT/LEFT REAR LEG (2)

I LEFT FRONT/RIGHT REAR LEG (2)

J KEYBOARD FRONT (1)

K KEYBOARD BACK (1)

L KEYBOARD SIDE (2)

M KEYBOARD SHELF (1)

M60 BOTTOM (2)

N2 DRAWER FRONT (2)

O DRAWER BOX FRONT (2)

T LARGE DRAWER FRONT (2)

U LARGE DRAWER BOX FRONT (2)

Y MOLDING (1)

Z END MOLDING (2)

408920 www.sauder.com/servicesPage 2

Part Identiﬁ cation

Now you know

our ABCs.

Part Identiﬁ cation

A

B

C3

D3

EE3

M60

G

H

I

J

K

L

M

N2

O

T

U

Y

Z

408920www.sauder.com/services

Page 3

D29

D28

D77

D78

D707

D132

D138

Hardware Identiﬁ cation

LONG SUPPORT

ROD - 1

24A

TURNBUCKLE - 1

9A

SHORT SUPPORT

ROD - 1

23A

(EXTENSION SET SHOWN SEPARATED)

FILE ROD - 4

8B

7F

TWIST-LOCK

®

FASTENER - 5

ANCHOR PLATE - 2

66G

10A

SLIDE

CAM - 8

HINGE - 2

12H

CAM SCREW - 12

8F

HIDDEN CAM - 40

1F

CAM DOWEL - 28

2F

(EXTENSION SET SHOWN SEPARATED)

WIDE EXTENSION

RAIL - 4

GG

WIDE EXTENSION

SLIDE - 4

HH

NARROW EXTENSION

RAIL - 4

JJ2

NARROW EXTENSION

SLIDE - 4

KK2

408920 www.sauder.com/servicesPage 4

FILE GLIDE - 4

15B

40AW

CABINET RIGHT - 1

40AX

CABINET LEFT - 1

40AY

DRAWER RIGHT - 1

40AZ

DRAWER LEFT - 1

22A

SPACER - 2

Hardware Identiﬁ cation

å Screws are shown actual size. You may receive extra hardware with your unit.

31S

BLACK 7/8" FLAT HEAD SCREW - 4

SILVER 1-1/8" FLAT HEAD SCREW - 4

10S

SILVER 1-1/4" MACHINE SCREW - 12

35S

BLACK 1-7/8" FLAT HEAD SCREW - 6

2S

GROMMET CAP - 1

1P

18S

BROWN 1" FLAT HEAD SCREW - 4

3S

GOLD 5/16" FLAT HEAD SCREW - 36

METAL PIN - 4

1R

23S

SILVER 5/8" FLAT HEAD SCREW - 4

54S

SILVER 9/16" LARGE HEAD SCREW - 10

PULL - 6

7K

32S

BLACK 9/16" FLAT HEAD SCREW - 9

KNOB - 2

24K

GROMMET - 1

10P

408920www.sauder.com/services

Page 5

30S

BLACK 1-9/16" FLAT HEAD SCREW - 16

GOLD 1" MACHINE SCREW - 2

50S

Step 1

Look for this icon. It means a

video assembly tip is available at

www.sauder.com/services/tips

Do not tighten the TWIST-LOCK® FASTENERS in this step.

å

Assemble your unit on a carpeted ﬂ oor or on the empty

carton to avoid scratching your unit or the ﬂ oor.

å

To begin assembly, push a SAUDER TWIST-LOCK®

FASTENER (7F) into the large holes in the

MODESTY PANEL (G).

G

7F

408920 www.sauder.com/servicesPage 6

Scan this QR code or go to this address:

http://qr.sauder.com/?ID=1534

to watch a video on how to assemble your unit.

STOP

If you purchased

the 408750

Hutch, assemble

that unit ﬁ rst.

å

Push forty HIDDEN CAMS (1F) into the ENDS (A and B),

UPRIGHTS (C3 and D3), both BOTTOMS (M60), and

the MODESTY PANEL (G). Then, insert the metal end of

twenty-eight CAM DOWELS (2F) into the HIDDEN CAMS.

Step 2

A

B

C3

D3

M60

G

Insert the metal end of the CAM

DOWEL into the HIDDEN CAM.

Arrow

Do not tighten the HIDDEN CAMS in this step.

Do not insert

CAM DOWELS

into these edges.

(40 used)

(28 used)

Arrow

2F

1F

Arrow

The arrow in the HIDDEN

CAM must point toward the

hole in the edge of the board.

Hole

408920www.sauder.com/services

Page 7

Step 3

å

Turn twelve CAM SCREWS (8F) into the LEGS (H and I).

8F

H

I

Just think. The sooner

you do this, the sooner

you do something else.

408920 www.sauder.com/servicesPage 8

(12 used)

å

Fasten one of each LEG (H and I) to the ENDS (A and B).

Tighten six HIDDEN CAMS.

Step 4

Curved edge

A

B

H

I

Surface with

HIDDEN CAMS

Surface with

HIDDEN CAMS

408920www.sauder.com/services

Page 9

1

2

Curved edge

These surfaces

should be even.

These surfaces

should be even.

Edge with

HIDDEN CAMS

å

Turn six BLACK 9/16" FLAT HEAD SCREWS (32S) into

the ENDS (A and B) until the shoulders of the SCREWS

rest on the surfaces of the ENDS.

å

NOTE: Do not overtighten the SCREWS.

å

Now, slide the END MOLDINGS (Z) onto the ENDS (A

and B). To do this, line up the grooves in the MOLDINGS

over the heads of the SCREWS in the ENDS. Using your

hands, apply pressure on the MOLDINGS as you guide

the MOLDINGS onto the ENDS.

å

NOTE: If the MOLDINGS come up o of the SCREWS,

remove them and slide them on again.

Step 5

A

B

Z

Surface without

HIDDEN CAMS

Surface without

HIDDEN CAMS

BLACK 9/16" FLAT HEAD SCREW

(6 used in this step)

32S

These edges

should be even.

These edges

should be even.

Shoulder

408920 www.sauder.com/servicesPage 10

Apply pressure with your hands

as you guide the MOLDINGS over

the SCREWS and onto the ENDS.

å

Fasten the remaining LEGS (H and I) to the ENDS (A

and B). Tighten six HIDDEN CAMS.

Step 6

H

I

A

B

Surface with

HIDDEN CAMS

Surface with

HIDDEN CAMS

Curved edge

408920www.sauder.com/services

Page 11

Curved edge

Edge with

HIDDEN CAMS

å

Turn three BLACK 9/16" FLAT HEAD SCREWS (32S)

into the MODESTY PANEL (G) until the shoulders of the

SCREWS rest on the surface of the MODESTY PANEL.

å

NOTE: Do not overtighten the SCREWS.

å

Now, slide the MOLDING (Y) onto the MODESTY

PANEL (G). To do this, line up the groove in the MOLDING

over the heads of the SCREWS in the MODESTY PANEL.

Using your hands, apply pressure on the MOLDING as

you guide the MOLDING onto the MODESTY PANEL.

å

NOTE: If the MOLDING comes up o of the SCREWS,

remove it and slide it on again.

Step 7

BLACK 9/16" FLAT HEAD SCREW

(3 used in this step)

32S

These edges

should be even.

Shoulder

Apply pressure with your hands

as you guide the MOLDINGS over

the SCREWS and onto the ENDS.

G

Y

Surface without

HIDDEN CAMS

408920 www.sauder.com/servicesPage 12

å

Turn the MODESTY PANEL (G) over and fasten the

MOLDING (Y) to the MODESTY PANEL. Use four

BLACK 7/8" FLAT HEAD SCREWS (31S).

Step 8

Y

BLACK 7/8" FLAT HEAD SCREW

(4 used in this step)

31S

408920www.sauder.com/services

Page 13

G

Surface with

HIDDEN CAMS

å

NOTE: Before beginning this step, separate the NARROW EXTENSION SETS (JJ2 and KK2) from the WIDE EXTENSION

SETS (GG and HH). Do not confuse these SETS once they are separated.

å

Separate the WIDE EXTENSION SLIDES (HH) from the WIDE EXTENSION RAILS (GG) as shown in the upper diagram

below. Be prepared, the parts are greasy.

å

Fasten the WIDE EXTENSION RAILS (GG) to the ENDS (A and B) and UPRIGHTS (C3 and D3). Use eight GOLD 5/16"

FLAT HEAD SCREWS (3S) through holes #1 and #3.

å

NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner

cartridge of the EXTENSION RAIL in to ﬁ nd the other holes that line up with the holes in the ENDS and UPRIGHTS. Turn a

SCREW into this hole.

å

NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.

Step 9

Open end

Push the black lever in and pull the SLIDE from the RAIL.

Wide

Extension

Rails

Wide

Extension

Rails

Open end

GOLD 5/16" FLAT HEAD SCREW

(8 used in this step)

3S

A

B

C3

D3

GG

HH

1

2

3

4

1

2

3

4

408920 www.sauder.com/servicesPage 14

å

Separate the NARROW EXTENSION SLIDES (KK2) from the NARROW EXTENSION RAILS (JJ2) as shown in the upper

diagram below. Be prepared, the parts are greasy.

å

Fasten the NARROW EXTENSION RAILS (JJ2) to the ENDS (A and B) and UPRIGHTS (C3 and D3). Use eight GOLD 5/16"

FLAT HEAD SCREWS (3S).

å

NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the enlarged diagram. Then, slide the inner

cartridge of the EXTENSION RAIL in to ﬁ nd the other hole that lines up with the hole in the END and UPRIGHT. Turn a

SCREW into this hole.

å

NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.

Step 10

Narrow

Extension

Rails

Narrow

Extension

Rails

GOLD 5/16" FLAT HEAD SCREW

(8 used in this step)

3S

Open end

Push the black lever in and pull the SLIDE from the RAIL.

A

B

C3

D3

JJ2

KK2

408920www.sauder.com/services

Page 15

å

Fasten the CABINET RAILS (40AW and 40AX) to the

other surfaces of the UPRIGHTS (C3 and D3). Use four

GOLD 5/16" FLAT HEAD SCREWS (3S).

å

NOTE: The CABINET RAILS are marked "CABINET

RIGHT" and "CABINET LEFT" for easy identiﬁ cation.

Step 11

Finished edge

GOLD 5/16" FLAT HEAD SCREW

(4 used in this step)

3S

D3

408920 www.sauder.com/servicesPage 16

Roller end

Surface without

HIDDEN CAMS

C3

Surface without

HIDDEN CAMS

40AW

40AX

Don't worry. It isn't

Rome. This can be built

in a day.

å

Fasten the UPRIGHTS (C3 and D3) to the MODESTY

PANEL (G). Tighten six HIDDEN CAMS.

Step 12

C3

D3

Finished edge

G

Surface without

HIDDEN CAMS

Surface with

HIDDEN CAMS

Surface with

HIDDEN CAMS

408920www.sauder.com/services

Page 17

Edge with MOLDING

Start Tighten

Arrow

Minimum

190 degrees

Caution

Risk of damage or

injury. HIDDEN CAMS

must be completely

tightened. HIDDEN

CAMS that are not

completely tightened

may loosen, and parts

may separate. To

completely tighten:

Arrow

Maximum

210 degrees

å

Insert four METAL PINS (1R) into the BOTTOMS (M60).

å

Insert the METAL PINS (1R) in one end of the BOTTOMS (M60)

into the holes in the UPRIGHTS (C3 and D3).

å

Fasten the BOTTOMS (M60) to the UPRIGHTS (C3 and D3).

Tighten two HIDDEN CAMS.

Step 13

Arrow

Minimum

190 degrees

Maximum

210 degrees

C3

D3

M60

1R

Finished edge

Surface with

HIDDEN CAMS

Surface with

HIDDEN CAMS

408920 www.sauder.com/servicesPage 18

1R

å

Fasten the ENDS (A and B) to the BOTTOMS (M60) and

MODESTY PANEL (G). Tighten eight HIDDEN CAMS.

å

NOTE: Be sure the METAL PINS in the BOTTOMS insert

into the holes in the ENDS.

Step 14

Arrow

Minimum

190 degrees

Maximum

210 degrees

A

B

M60

G

408920www.sauder.com/services

Page 19

å

Fasten the TOP (EE3) to the MODESTY PANEL (G).

Tighten ﬁ ve TWIST-LOCK® FASTENERS.

å

Fasten the TOP (EE3) to the ENDS (A and B) and

UPRIGHTS (C3 and D3). Tighten twelve HIDDEN CAMS.

Step 15

How to use the SAUDER TWIST-LOCK

®

FASTENER

1. Insert the dowel end of the FASTENER into the hole of the

adjoining part.

NOTE: The dowel end of the FASTENER must remain fully

inserted in the hole of the adjoining part while locking

the FASTENER.

2. Tighten the FASTENER with a Phillips screwdriver as tight

as possible.

Dowel end

Arrow

Minimum

190 degrees

Maximum

210 degrees

A

B

D3

EE3

G

C3

408920 www.sauder.com/servicesPage 20

Meet Part (EE3). This component has

been engineered to be lighter, stronger,

faster… well ok. Not technically faster.

But deﬁ nitely makes for a sturdier

Executive Desk that’s easier to assemble

and friendlier to the environment.

La page est en cours de chargement...

Sauder Shoal Creek 408920 Mode d'emploi

Sauder Shoal Creek 408920 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents