Extron Cable Cubby 650 UT Manuel utilisateur

Marque: Extron

Modèle: Cable Cubby 650 UT

Taper: Manuel utilisateur

IMPORTANT:

Go to www.extron.com for the

complete user guide

, installation

instructions, and specifications.

Cable Cubby 650 UT • Installation Guide

This guide provides instructions for an experienced technician to install and connect

the Extron Cable Cubby 650 UT.

The Cable Cubby 650 UT units are under furniture mountable and are expandable

for cable access, connections, and AC power.

NOTE: This product is intended for use only with Extron UL

listed power modules (not included). Go to www.extron.com for

recommended power modules.

Planning

Check with local and state regulations before starting the

installation

 Ensure that the planned installation complies with national and local building and electrical codes.

 Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.

Check all parts and equipment before installation

 Ensure that all parts are present in each kit.

 Ensure that necessary tools and equipment are available for the installation.

Kit Contents

125V~ 12A MAX TOTAL

Cable Cubby 650 UT

6 (3/8"), 2 (1/4")

#4-40 Module Screws

#6 Pan-head Mounting

Screws and Star Washers

AAP Frame Plate

Cable Grommet Plate

Hole Plugs

Retractor Pin & Clip

Connectivity Bracket

#4-40 Module Screws

AAP Frame Plate

Cable Grommet Plate

Hole Plugs

Retractor racket

Retractor Pin

& Clip

#6-32 Mounting screws and

Star Washers

Cable Cubby 650 UT • Installation Guide (Continued)

Preparing the Table

Cut a hole in the surface where the enclosure will be installed. The size of the hole depends on the number of enclosures used

(see Cut-out dimensions on the next page). Ensure the sides of the hole are smooth after cutting and nished before installing.

Read the following information before making a cut.

Determine the best location for the enclosure

 Ensure that the location where the Cable Cubby is to be installed is convenient for as many users as possible.

 Ensure that there is ample space under the table for cables. Allow at least 36 inches of cable loop for each cable (see

Routing and Connecting Cables on page7).

 When installing Retractors in the Cable Cubby, ensure that there is enough space for the Retractor assembly under the table

or furniture.

NOTE:

• To prevent objects from impeding cable retraction, allow at least 3 inches of clearance from the exposed cable side of

the enclosure (see the diagrams below).

• Excess cabling may cause clearance issues. Use zip ties to secure under-table cabling to prevent accidental contact or

entanglement (see Routing and Connecting Cables).

22.95"

(583 mm)

26.47"

(672 mm)

21.28"

(540 mm)

12.23"

(311 mm)

9.23"

(234 mm)

Table Top

Series/2

9.0"

(229 mm

)

15.14"

(385 mm)

21.14"

(537 mm)

Series/2 XL

3.0"

(76 mm)

3.0"

(76 mm)

28.95"

(735 mm)

Cut the hole in the table and pre-drill mounting holes

CAUTION: Wear safety glasses when operating power equipment. Failure to comply can result in eye injury.

ATTENTION : Portez des lunettes de sécurité lorsque vous utilisez l’équipement électrique. Ne pas respecter

cela peut conduire à une blessure à l’oeil.

ATTENTION: The opening in the table for the Cable Cubby should be cut only by licensed and bonded

craftspeople. Exercise care to prevent scarring or damaging the furniture.

ATTENTION : L’ouverture dans la table pour le Cable Cubby devrait être coupée seulement par des artisans

autorisés et qualiés. Faites attention à ne pas faire de marques sur le meuble et à ne pas l’endommager.

Cut-out dimensions

For one or two enclosures, the cut-out dimensions and mounting hole locations are shown below. For more enclosures, multiply

the length accordingly. If necessary, pre-drill into the furniture at the keyhole and mounting hole locations.

10"

(254 mm)

SURFACE

CUT-OUT

AREA

” (1.5 mm)

(108 mm)

Mounting Holes (16)

11.5"

(292 mm)

12"

(305 mm)

(127 mm)

SURFACE

CUT-OUT

AREA

” (1.5 mm)

4 1/4"

(108 mm)

1.5"

(38 mm)

(178 mm)

1.5"

(38 mm)

(76 mm)

(152 mm)

6.5"

(165 mm)

6.5"

(165 mm)

Mounting Holes (8)

(152 mm)

6.5"

(165 mm

)

(76 mm)

1.5"

(38 mm)

1.5"

(38 mm)

Keyholes (4)

Keyholes (2)

2.0"

(51 mm)

NOTE: Diagrams shown above are not drawn to scale.

Dimensions and cut-out templates are available online at www.extron.com.

Cable Cubby 650 UT • Installation Guide (Continued)

Preparing the Cable Cubby

Step 1 (Only for multiple enclosures) — Assemble Enclosures

Repeat steps 1 and 2 to

add more enclosures to

the extension.

Before attaching the enclosur

ensure the keyhole mounting

holes are orientated in the

same direction.

Attach the enclosures together

with the four pan-head

mounting screws and washers

that were removed in step 1.

Using a #2 screw driver,

unscrew the four pan-head

screws that attach the enclosure

sides of the Cable Cubby together.

Repeat this step on the corresponding

side of the other enclosure.

Detach side panels of both enclosures.

Step 2 — Assemble Connectivity Modules

Connectivity modules allow you to populate the Cable Cubby enclosure with a combination of AAPs, cable pass-through, or

Retractors. Follow the steps below to assemble the connectivity modules of your choice.

Option 1: AAP Module

Secure up to three single-space

AAPs in the AAP plate.

Secure the AAP plate on the connectivity brackets,

using four of the provided module screws.

#4-40 Nut with

Captive Washer

Insert cables through the bottom of the connectivity bracket.

Connect cables to the AAPs.

Option 2: Cable Pass-Through Module

Secure the grommet

plate on the connectivity

bracket using four of the

provided module screws.

Insert cables through

the bottom of the connectivity

bracket and into the holes of

the grommet plate.

Snap the included

hole plugs into any

unused holes.

Option 3: Retractor Bracket

Secure the bracket using four of

the provided pan-head mounting

screws with star washers. Tighten

the screws using a screwdriver.

Insert the bracket as shown.

The bracket may be installed on the left

or right side of the enclosure and at the

lowest height.

NOTE: The opening of the

bracket should be installed

towards the outside of the

enclosure.

Step 3 — Install the Modules

Determine where the connectivity modules and/or power module will be installed in the Cable Cubby. The modules may be

installed on the left or right side of the enclosure and at various heights.

For the Power module:

WARNING: Risk of Electric Shock. To

ensure proper electrical grounding, use the

provided #6-32 mounting screws with the star

washers.

AVERTISSEMENT : Risque de choc

électrique. An d’assurer une mise à la terre

correcte, utilisez les xations de mise à la terre

#6-32 et les rondelles en étoile fournies.

125V~ 12A MAX TOTAL

Secure the modules

using four of the provided

pan-head mounting screws

and star washers.

Insert the modules

into the Cable Cubby.

Mounting the Cable Cubby in the Table

Align the enclosure with the pre-drilled holes under the furniture. Secure the enclosure with the appropriate screws (see Cut the

hole in the table and pre-drill mounting holes on page3).

125V~ 12A MAX TOTAL

Hook the Cable Cubby assembly

onto the screws, as shown at right.

Slide the Cable Cubby assembly

into slot.

Tighten the screws to secure

the Cable Cubby assembly.

Insert a mounting screw (provided) into each

of the two holes. Tighten each screw until it

protrudes 1/4 inch from the bottom of the table.

Drill pilot holes through the clearance

openings on the Cable Cubby. Insert and

tighten mounting screws (provided).

Clearance

Opening

Cable Cubby 650 UT • Installation Guide (Continued)

Installing Retractors

Follow the steps below to install Retractors. Before installing the Retractors, adjust the Retractors for horizontal or angular

mounting, see the information below, then follow the installation steps below.

Horizontal Mounting

Remove two enclosure screws

(one on each side) from this position.

Then, mount the Retractors as shown

below.

Cable Release

Assembly

Move the cable release assembly upward until

the angular mounting hole is visible. Reinstall the

enclosure screws in this hole (both sides).

See the Cable Retractor Series/2 Setup Guide, available on the

Extron website, for additional steps.

Angular Mounting

Remove the enclosure screws as shown on the left, then follow this

step:

Remove two enclosure screws

(one on each side) from this position.

Then, mount the Retractors as shown

below.

Cable Release

Assembly

Move the cable release assembly upward until

the angular mounting hole is visible. Reinstall the

enclosure screws in this hole (both sides).

NOTE: Extron recommends mounting the Retractor bracket so the release buttons for the Retractor are against the wall of

the enclosure, to ensure adequate clearance below the Cable Cubby.

Insert the pin thr

ough the

Retractor mounting hole on

the side of the Cable Cubby

and Retractor assembly

Secure the clip

on the pin.

Insert Retractors into

the Retractor bracket.

Secure the locking screw

on each Retractor. Do not

overtighten.

Step 2 — Under the table, adjust the side clamps on the enclosure

Alternative Retractor Conﬁguration for Cable Cubby 650 UT

Optional Double Retractor bracket mounting:

Install brackets as shown below. Two double Retractor brackets can mount up to four Retractors.

NOTE: Mount the Double Retractor bracket with the release buttons for the Retractor against the wall of the enclosure,

opposite from each other, as shown below. DO NOT mount the Double Retractor bracket side by side. There is not enough

space to insert the mounting pins side by side.

Side View

Top View

Secure the brackets using

four of the provided pan-head

mounting screws with star

washers. Tighten the screws

using a screwdriver.

Insert the brackets as shown.

The bracket may be installed

on the left or right side of the

enclosure and at the lowest height.

Routing and Connecting Cables

For cable pass-through applications,

allow at least 36 inches (0.9 m) of cable

loop for each cable.

Connect cables to the AV system

and connect the AC power cord.

Using zip ties, secure cables to the holes

on the bottom of the Cable Cubby.

NOTE: Ensure that there is no tension on the power cable.

CAUTION:

Risk of Electric Shock.

This equipment must be grounded.

ATTENTION :

Risque de choc électrique.

Cet équipement doit être xé au sol.

NOTE: Mount Retractors opposite each other (see

images above).

68-3062-50 Rev. B

08 18

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Installation Checklist

Planning (page1)

 Check with local and state regulations before starting the installation

 Check all parts and equipment before installation

 Determine number of enclosures to install

Preparing the Table (page2)

 Determine the best location for the enclosure

 Verify sufcient space under furniture

 Cut a hole in the table and pre-drill mounting holes (page 3)

Preparing the Cable Cubby (page4)

 If applicable, assemble enclosures

 Assemble connectivity modules

 Install the modules (page 5)

Mounting the Cable Cubby in the Table (page5)

 Mount the Cable Cubby under the table

Installing Retractors (page6)

 Remove Retractor screws for horizontal and angular mount applications

 Install Retractors into the bracket

Routing and Connecting Cables (page7)

 Dress cables under the table

 Connect cables to the AV system

Extron Cable Cubby 650 UT Manuel utilisateur

Marque: Extron

Modèle: Cable Cubby 650 UT

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Extron Cable Cubby 650 UT User manual

Extron Cable Cubby 650 UT Manuel utilisateur

Extron Cable Cubby 650 UT Manuel utilisateur

dans d''autres langues

Documents connexes