Extron Cable Cubby 500 Manuel utilisateur

Marque: Extron

Modèle: Cable Cubby 500

Catégorie: Câbles de signal

Taper: Manuel utilisateur

Ce manuel convient également à

Cable Cubby 700

IMPORTANT:

Go to www.extron.com for the complete

user guide, installation instructions, and

specifications before connecting the

product to the power source.

Cable Cubby 500 and 700 • Installation Guide

This guide provides instructions for an experienced installer to install and connect the Extron

Cable Cubby 500 and 700 Cable Access Enclosures.

The Cable Cubby units are furniture-mounted enclosures for cable access,

connections, and AC power. Cables that are not in use can be stored out of

the way while remaining connected to the presentation system.

Planning

Check with local and state regulations before starting the

installation:

Ensure that the planned installation complies with building and electrical codes.

Ensure that the planned installation complies with the Americans with Disabilities Act or

other accessibility requirements.

Check all parts and equipment before installation:

Ensure that all parts are present in each kit.

Ensure that necessary tools and equipment are available for the installation.

Cable Cubby 500 and Cable Cubby 500 CCB Cable Cubby 700

1 2

2 4

1 2

(3) 3/8", (1) 1/4" (6) 3/8", (2) 1/4"

1 trim, 2 screws 2 trims, 4 screws

1 2

4 8

Kit Contents

Hole Plugs

Connectivity Bracket Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500 Cable Cubby 700

Zip Ties

Tweeker

AC Power Module

125V~ 12A MAX TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

Cable Frame Plate (1)

Hole Plugs

Connectivity Bracket Cable Grommet Plate

AAP Frame Plate

Cable Cubby 500 Cable Cubby 700

Zip Ties

Tweeker

AC Power Module

125V~ 12A MAX TOTAL

Retractor Trim

and Screws

Retractor Pin & Clip

#6 Mounting Screws

and Star Washers

#4-40 Module Screws

ii Bk

Cable Frame Plate (1)

Retractor Trim

and Screws

Connectivity Bracket

#6 Mounting Screws

and Star Washers

Cable Grommet Plate

Cable Frame Plate

Zip Ties

Retractor Pin and Clip

Hole Plugs

Cable Cubby 500 CCB

Cable Cubby 500 and 700 • Installation Guide (Continued)

23.3"

(592 mm)

26.9"

(683 mm)

21.7"

(550 mm)

11.8"

(300 mm)

8.8"

(224 mm)

Table Top

Retractor Series

9.0"

(229 mm)

15.2"

(386 mm)

21.2"

(538 mm)

Retractor Series XL

3.0"

(76 mm)

3.0"

(76 mm)

29.3"

(744 mm)

Retractor Series XL

Retractor Series

Preparing the Table

Cut a hole in the surface where the enclosure will be installed. Read the following information before making a cut.

Determine the best location for the enclosure

Ensure that the location where the Cable Cubby is to be installed is convenient for as many users as possible.

Ensure that the edge on which the lid opens is oriented correctly.

Ensure that there is ample space under the table for cables.

When installing Retractors in the Cable Cubby, ensure that there is enough space for the Retractor assembly under the table

or furniture (see dimensions for the Retractors below).

Choose a method for cutting the hole in the table

ATTENTION:

• The opening in the table for the Cable Cubby should be cut only by licensed and bonded craftspeople. Exercise care to

prevent scarring or damaging the furniture.

• L’ouverture dans la table pour le CableCubby devrait être coupée seulement par des artisans autorisés et qualifiés.

Faites attention à ne pas faire de marques sur le meuble et à ne pas l’endommager.

CAUTION: Wear safety glasses when operating power equipment. Failure to comply can result in eye injury.

ATTENTION: Portez des lunettes de sécurité lorsque vous utilisez l’équipement électrique. Ne pas respecter cela peut

conduire à une blessure à l’oeil.

Choose one of the following methods for cutting the hole:

Hand Router and Routing Template Jigsaw and Paper Cut-Out Template CNC Wood Router

If using a CNC wood router or other

precise machinery, use the exact

cut-out dimensions for your model

(see the table below).

Visit www.extron.com for Cable Cubby routing

template part numbers and instructions.

Dimensions and cut-out templates are

available online at www.extron.com.

Cable

Cubby

Model

Cut-out Dimensions

User Access

Width

Side

Dimension

500 5.75" (14.6 cm) 5.75" (14.6 cm)

700 7.125" (18.1 cm) 5.75" (14.6 cm)

500 CCB 5.75” (14.6 cm) 7.125” (18.1 cm)

NOTES:

• To prevent objects from impeding cable retraction, allow at least 3 inches of clearance from the exposed cable side of

the enclosure (see the diagrams below).

• Excess cabling may cause clearance issues. Use zip ties to secure under-table cabling to prevent accidental contact or

entanglement (see Routing and Connecting Cables on page 6).

Cut-Out Template for the Extron

Cable Cubby 500

0.25"

(0.635 cm) R

User Access

5.75"

(14.60 cm)

5.75"

(14.60 cm)

0.25"

Trim Ring

Lip Width

2.0"

Trim Ring’s Outer Edge

(Do not cut this line.)

0.00” (0.00 cm)

0.02 (0.05 cm)

Table Clamp

P/N 68-8599-01 Rev. A

SURFACE

CUT-OUT

AREA

1. Confirm the product to be installed.

2. Remove the surface cut-out area

(gray) from the template.

3. Measure the cutout and template.

4. Mark the position on the

furniture where the Cable Cubby 500

will be installed.

5. Double check dimensions and position,

then cut the opening.

Page Size: 11" x 17"

Print Scale 1:1

Do not Shrink

0.25"

(0.635 cm) R

5.75"

(14.60 cm)

5.75"

(14.60 cm)

SURFACE

CUT-OUT

AREA

Cut-Out Template for the Extron

Cable Cubby 500

User Access

0.25"

Trim Ring

Lip Width

2.0"

Trim Ring’s Outer Edge

(Do not cut this line.)

0.00” (0.00 cm)

0.02 (0.05 cm)

Table Clamp

P/N 68-8599-01 Rev. A

1. Confirm the product to be installed.

2. Remove the surface cut-out area

(gray) from the template.

3. Measure the cutout and template.

4. Mark the position on the

furniture where the Cable Cubby 500

will be installed.

5. Double check dimensions and position,

then cut the opening.

Page Size: 11" x 17"

Print Scale 1:1

Do not Shrink

Jigsaw

Cut O

Cut-Out T

Cab

125V~ 50-60Hz 12A MAX TOTAL

TOP

125V~ 50-60Hz 12A MAX TOTAL

TOP

Insert the modules

into the

Cable Cubby.

Secure the modules using

the provided mounting

screws and star

washers (4) on the

front and back of the

enclosure.

AAP Module

Cable Pass-Through Module

Retractor Trim

Preparing the Cable Cubby

Step 1 — Assemble the connectivity modules of your choice.

Connectivity modules allow you to populate the Cable Cubby with a combination of AAPs, cable pass-throughs, or Retractors.

NOTE:

• Use a screwdriver to secure the Retractor trim with the screws.

• After installing the trim, proceed to “Step 2 — Install the modules”

to install the power module.

• Retractors are installed after the Cable Cubby is mounted on the

table (see Installing Retractors on page 5).

NOTE: After assembling the module,

proceed to “Step 2 — Install the

modules.”

Secure the retractor trim

using the provided

mounting screws (2).

Step 2 — Install the modules

Determine where the connectivity modules and power module will be

installed in the Cable Cubby. The modules may be installed at various

heights.

NOTE:

• Ensure that there is enough room above the modules for

the Cable Cubby lid to close completely.

• Use a screwdriver to secure the modules with the screws.

WARNING: Risk of Electric Shock. To ensure proper electrical

grounding, use the provided #6-32 mounting screws with the

star washers.

AVERTISSEMENT: Risque de choc électrique. Afin d’assurer

une mise à la terre correcte, utilisez les fixations de mise à la

terre #6-32 et les rondelles en étoile fournies.

NOTE: After assembling the module, proceed to “Step 2 — Install the modules.”

Secure up to two

single-space AAPs

in the AAP plate.

#4-40 Nut

w/ Captive Washer Insert cables through the bottom

of the connectivity bracket.

Connect cables to the AAPs.

Secure the AAP plate on the

connectivity brackets, using

two of the provided module

screws.

Insert cables through the bottom

of the connectivity bracket and

into the holes of the grommet plate.

Secure the grommet plate on

the connectivity bracket using

two of the provided module

screws.

Snap the included hole plugs

into any unused holes.

Insert cables

through the

bottom of the

connectivity

bracket and into

the holes of the

grommet plate.

Secure the

grommet plate

on the connectivity

bracket using two

of the provided

module screws.

Snap the included

hole plugs into

any unused holes.

For Show Me Cables:

Insert Show Me

Cables into the

grommet plate.

Attach the Show Me

Cable Trim Plate to the

top of the module, using

the module screws.

Attach the grommet

plate to the bottom

of the module, using

the module screws.

Step 1 — Mount the Cable Cubby ﬂush with the table.

Mounting the Cable Cubby in the Table

Connecting a Cable Cubby 500 CCB

For Cable Cubby 500 CCB models, follow the instructions below, then proceed to Mounting the Cable Cubby in the Table.

The Cable Cubby 500 CCB contains three contact closure buttons to control input selection on Extron switchers and products

with contact closure control ports. Wire the Cable Cubby switches to the control product as shown in the wiring diagram below.

To wire the captive screw connectors:

1. Strip away 3 inches of the outer jacket

from the end of the cable, and

3/16 inch (5 mm) of the inner jacket

from the end of each wire.

2. Secure the wires to the captive screw

connector using an Extron Tweeker

or other small screwdriver. Follow the

wiring diagram at the right.

CAUTION: The flanged edges of the top of the surface

enclosure are sharp. These edges are also soft and

may be easily nicked or bent. Exercise caution when

handling the enclosure to prevent personal injury or

damage to the enclosure.

ATTENTION: Les extrémités à brides du haut de la

surface du boîtier sont aiguisées. Ces extrémités

sont aussi lisses et peuvent facilement être coupées

ou pliées. Soyez prudents lorsque vous manipulez

le boîtier afin d’éviter de l’endommager ou de vous

blesser.

NOTE: See the table at right to

determine and select the appropriate

current-limiting resistor, if needed.

CGT+V

CNONC

Contact (C)

Ground (G)

Tally output (T)

Tally voltage (+V)

RESISTOR

Extron Switcher with

Contact Closure Input

and Tally Output

Lower the Cable Cubby into the hole to test the t.

If necessary, carefully enlarge the opening.

Remove the plastic strips

and lm on the surface of

the Cable Cubby.

Ensure that the

side clamps are

seated against

the enclosure.

Blue

1A @

24 VDC /

125 VAC

See

note

below

4.52 K,

13 K,

Momentary switch

(single pole, double throw)

on captive screw terminal

NOTE: No resistor required for 5 VDC source.

Cable Cubby 500 and 700 • Installation Guide (Continued)

Step 2 — Under the table, adjust the side clamps on the enclosure.

Installing Retractors

Follow the steps below to install Retractors. For horizontal or angular Retractor

mounting, see the information at right, then follow the steps below.

NOTE: To lower the side

clamp, turn the lever

down, then press and

hold the locking plate

while sliding down the

clamp.

Angular Mounting

Remove the enclosure screws as shown above, then follow

this step:

Horizontal Mounting

See the Cable Retractor Setup Guide, available on the

Extron website, for additional steps.

Remove two enclosure screws

(one on each side) from this position.

Then, mount the Retractors as shown

at left.

Cable Release

Assembly

Move the cable release assembly upward until

the angular mounting hole is visible. Reinstall the

enclosure screws in this hole (both sides).

Remove two enclosure screws

(one on each side) from this position.

Then, mount the Retractors as shown

at left.

Cable Release

Assembly

Move the cable release assembly upward until

the angular mounting hole is visible.

Reinstall the

enclosure screws in this hole (both sides).

Rotate the side clamp

outward and ensure that

the lever is down.

Slide the clamp all the way

up against the bottom of

the table.

Ensure the Cable Cubby

is rmly seated in the table.

Raise the lever to secure

the Cable Cubby.

Lever

12 3

Locking

plate

Secure the clip

on the pin.

Insert retractors into

the retractor trim.

Secure the locking screw on

each Retractor.

Insert the pin through the

retractor mounting hole on

the side of the Cable Cubby

and retractor assembly.

Do not overtighten. The locking

screw only needs to be snug.

68-3551-50 A

05 20

For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the

Extron Safety and Regulatory Compliance Guide on the Extron website.

All trademarks mentioned are the property of their respective owners.

Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876

Installation Checklist

Planning (page 1)

Check with local and state regulations before starting the installation.

Check all parts and equipment before installation.

Preparing the Table (page 2)

Determine the best location for the enclosure.

Choose a method for cutting the hole in the table.

Preparing the Cable Cubby (page 3)

Choose and assemble a combination of AAP, cable-pass through, and Retractor connectivity to populate the Cable Cubby.

Secure the connectivity modules and power module in the Cable Cubby.

Connecting a Cable Cubby 500 CCB (page 4)

Mounting the Cable Cubby in the Table (page 4)

Mount the Cable Cubby ush with the table.

Adjust the side clamps.

Installing Retractors (page 5)

Routing and Connecting Cables (page 6)

Routing and Connecting Cables

CAUTION:

Risk of Electric Shock.

This equipment must be grounded.

ATTENTION:

Risque de choc électrique.

Cet équipement doit être xé au sol.

NOTE: Ensure that there is no tension on the power cable.

Secure cables with zip ties to the rectangular

holes in the rear of the Cable Cubby.

For cable pass-through applications, allow at least 36 inches (0.9 m)

of cable loop for each cable.

Connect cables to the AV system

and connect the AC power cord.

Extron Cable Cubby 500 Manuel utilisateur

Marque: Extron

Modèle: Cable Cubby 500

Catégorie: Câbles de signal

Taper: Manuel utilisateur

Ce manuel convient également à

Cable Cubby 700

Télécharger le PDF

rapport

dans d''autres langues

English: Extron Cable Cubby 500 User manual

Extron Cable Cubby 500 Manuel utilisateur

Ce manuel convient également à

Extron Cable Cubby 500 Manuel utilisateur

dans d''autres langues

Documents connexes