Extron EDID 101H 4K PLUS Manuel utilisateur

Taper
Manuel utilisateur
1
IMPORTANT:
IMPORTANT:
Go to www.extron.com for the
complete user guide, installation
instructions, and specifications.
EDID 101H 4K PLUS • Setup Guide
This setup guide provides instructions for an experienced installer to install and operate the EDID 101H 4K PLUS.
The EDID 101H 4K PLUS is a single-input, single-output HDMI EDID emulator supporting video rates up to 4K@60 Hz 4:4:4. It
supports EDID Minder, HDCP 2.3, and Extron Product Conguration Software (PCS) conguration. The EDID 101H 4K PLUS can
also capture and store EDID information from a connected display via the front panel STORE button.
The EDID 101H 4K PLUS is housed in a 1 inch high, quarter-rack width, 6-inch deep enclosure. An external universal power
supply is included.
NOTE: For full installation, conguration, menus, connector wiring, and operation details, see the EDID 101H 4K PLUS User
Guide, available at www.extron.com
Rear Panel Cabling
POWER
12V
0.3A MAX
OUTPUTINPUT
EDID 101H 4K PLUS
A
B
C
Figure 1. EDID 101H 4K Plus Rear Panel
A
Power Connector — Connect the included 12VDC power supply to the orange, two-pole, 3.5mm captive screw
connector. Wire the power supply as shown in figure 2.
SECTION A–A
Ridges
Smooth
A
A
3/16"
(5 mm) Max.
POWER
12V
0.3A MA
X
Figure 2. External Power Supply Connection
ATTENTION: Risk of property damage:
ATTENTION : Risque de dommages matériels :
Do not connect any external power supplies until you have read the Attention notifications in the Power Supply section
of the user guide for that device.
Ne branchez pas de sources d’alimentation externes avant d’avoir lu les mises en garde dans la section « Power Supply
» du guide utilisateur pour cet appareil.
B
HDMI Input — Connect an HDMI source to this HDMI connector.
c
HDMI Output — Connect a display or other output device to the HDMI connector.
1
2
2
EDID 101H 4K PLUS • Setup Guide (Continued)
HDMI Connector LockIt Lacing Bracket
3
1
2
3
3
4
5
Figure 3. Connecting HDMI Cable to LockIt Lacing Bracket
Use the Extron LockIt Lacing Bracket to secure HDMI cables to the device.
1. Plug the HDMI cable into the rear panel connection (see figure3,
1
).
2. Loosen the HDMI connection mounting screw from the panel enough to allow the LockIt Lacing Bracket to be
placed over it (
2
). The screw does not have to be removed.
3. Place the LockIt Lacing Bracket on the screw and against the HDMI connector (
3
), then tighten the screw to
secure the bracket.
ATTENTION:
Do not overtighten the HDMI connector mounting screw. The shield to which it is fastened is very thin and can
easily be stripped.
Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage auquel elle est attachée est très fin et peut
facilement être dénudé.
4. Loosely place the included tie wrap around the HDMI connector and the LockIt Lacing Bracket as shown (
4
).
5. Hold the connector securely against the lacing bracket, tighten the tie wrap, then remove the excess length (
5
).
Front Panel
EDID 101H 4K PLUSExtron
SIGNAL
HDCP
IN OUT
STORE
EDID
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
CONFIG
AB C
D
Figure 4. EDID 101H 4K Plus Front Panel
A
Power LED – Illuminates when power is supplied.
B
Config Port – Connect a USB mini-B cable to provide USB communication with unit.
C
EDID STORE Button – When pushed in, the STORE button initiates both reading and storing the EDID from the connected
display. Press the STORE button to read the EDID of the connected device and store it to a user slot selected by the rotary
switch. Up to four EDID files (switch positions C through F) can be stored.
Reset – To reset the EDID101H4K PLUS to its default state, press and hold the STORE button while applying power. As
power is applied, all front panel LEDs blink 3 times indicating a successful reset.
D
EDID Selection Rotary Switch – The 16-position rotary switch allows the user to select from 12 factory EDID files
and 4 store slots. When any position 0-F is selected, the corresponding slot in the EDID lookup table will be
assigned to the input, and an unsolicited SIS response will be sent. This is summarized in the table on the next
page.
3
4
3
Rotary Switch Position Native Resolution Refresh Audio Format
0 1280 x 800 60 Hz 2-Ch
1 1600 x 900 60 Hz 2-Ch
2 1920 x1200 60 Hz 2-Ch
3 2560 x 1400 60 Hz 2-Ch
4 2560 x 1600 60 Hz 2-Ch
5 720p 50 Hz 2-Ch
6 720p 60 Hz 2-Ch
7 1080p 50 Hz 2-Ch
8 1080p 60 Hz 2-Ch
9 4K/UHD 30 Hz 2-Ch
A 4K/UHD 4:2:0 60 Hz 2-Ch
B 4K/UHD 4:4:4 60 Hz 2-Ch
C Store Slot 1
D Store Slot 2
E Store Slot 3
F Store Slot 4
LED State Rotary Switch Store Button Description
Off 0-B Non-functional EDID storing is not possible on the selected rotary position.
Green
(flashing)
C-F Button has been pressed
and released
The STORE button has been pressed and the EDID is currently
being stored to the selected user store slot.
Green
(solid)
C-F N/A EDID storing is possible on the selected rotary position, or the
storing process is complete (if following the ashing state).
Connect and Power the EDID 101H 4K PLUS
1. Set the rotary switch (see figure4 on the previous page) for the desired resolution.
2. Connect an HDMI cable from the source to the EDID 101H 4K PLUS Input (see figure4,
B
on page2).
3. Connect an HDMI cable from the EDID 101H 4K PLUS Output (see figure4) to the display or distribution system.
4. Turn on the video display.
5. Connect the power supply to the EDID101H 4K PLUS (see figure4).
6. Connect AC power to the power supply. The EDID 101H 4K PLUS power LED lights green.
7. Turn on the video source. The video source reads the EDID from the EDID101H 4K PLUS.
4
68-3109-50 Rev. B
06 20
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2020 Extron Electronics — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Extron EDID 101H 4K PLUS Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues