Wallenstein BXM32-BXM42 Setup Instructions

Set-up Instructions

Rev Nov-2019 Part Number: Z97127_SI

BXM32

BXM42

Always Put Safety First!

Read these assembly instructions thoroughly before

beginning. Make sure each step is understood before

attempting it. Be familiar with all safety signs on the

machine and their meaning.

Tighten all fasteners to the torque value specied on

the last page. Recheck before using the machine.

WARNING!

Position the crate in a large open area to allow

access from all sides during assembly.

Stay clear of overhead power lines and obstructions

when lifting the machine during assembly. Contact

with power lines can cause electrocution. Contact

with obstructions can damage components or cause

them to fail.

Keep the assembly area clean to prevent slipping or

tripping.

Use a hoist when lifting components that weigh 50 lb

(23 kg) or more to avoid back injury.

All lifting devices (straps, slings, chains, ratchet

blocks) must comply with applicable local

regulations and certications. Wallenstein Equipment

Inc. cannot accept responsibility for the use of

sub-standard equipment and work practices.

Use lifting equipment with a capacity greater than the

weight of the component. Place jack stands or wood

blocking under the machine to securely stabilize it

before working on it during assembly.

Use the correct tool for the job. Repair or replace

broken or defective equipment or tools. Makeshift

tools can create safety hazards. A tool that breaks or

slips during use risks personal injury.

WARNING!

Avoid the risk of personal injury or machine damage!

Read the operator’s manual before using this

equipment. Carefully read all safety messages in the

manual and follow all safety signs on the machine.

IMPORTANT! Inspect for damage from shipping.

Immediately contact the shipping company if damage

is found.

Note: Some parts are attached to skid with screws.

Shipping brackets are not reused.

Assembly hardware is located inside operator's manual

tube.

BXM32BXM42

BXM32

BXM42

1

2

BXM32

4X

4x

C

A

B

D

E

3

4X C

E

4

BXM32

2X 6X

A

E

5

4X

B

E

6

7

1

BXM42

2

2X

4X

4x

A

B

C

D

E

BXM42

2X

C

E

3

4

4X C

E

8X

A

F

BXM42

5

6

4X

B

E

7

BXM42

8

Pre-delivery Inspection

Inspect for damage from shipping. Immediately contact the

shipping company if damage is found.

BXM–Series Wood Chipper-Shredder

Check blade clearance and that rotor turns freely

Check that discharge and deﬂ ector move freely

Check that all fasteners are tight

Check that lock pins align and move freely

Check all grease points and lubricate pivot points

Review operating and safety instructions in the Operator's

Manual

Safety Checks

All Safety Decals Installed

Guards and Shields Installed and Secured

Check that the Slow Moving Vehicle sign is installed

Check that retainers are installed through hitch points

Review operating and safety instructions in the Operator's

Manual

9

Bolt Torque Specications

Checking Bolt Torque

The tables shown give correct torque values

for various bolts and capscrews. Tighten all

bolts to the torque values specied in the

table, unless indicated otherwise. Check

tightness of bolts periodically.

IMPORTANT! If replacing hardware, use

fasteners of the same grade.

IMPORTANT! Torque gures indicated in

the table are for non-greased or non-oiled

threads. Do not grease or oil threads

unless indicated otherwise. When using a

thread locker, increase torque values by

5%.

Note: Bolt grades are identied by their

head markings.

Imperial Bolt Torque Specications

Bolt

Diameter

Torque Value

SAE Gr. 2 SAE Gr. 5 SAE Gr. 8

lbf•ft N•m lbf•ft N•m lbf•ft N•m

1/4" 6 8 9 12 12 17

5/16" 10 13 19 25 27 36

3/8" 20 27 33 45 45 63

7/16" 30 41 53 72 75 100

1/2" 45 61 80 110 115 155

9/16" 60 95 115 155 165 220

5/8" 95 128 160 215 220 305

3/4" 165 225 290 390 400 540

7/8" 170 230 420 570 650 880

1" 225 345 630 850 970 1320

Metric Bolt Torque Specications

Bolt

Diameter

Torque Value

Gr. 8.8 Gr. 10.9

lbf•ft N•m lbf•ft N•m

M3 0.4 0.5 1.3 1.8

M4 2.2 3 3.3 4.5

M6 7 10 11 15

M8 18 25 26 35

M10 37 50 52 70

M12 66 90 92 125

M16 166 225 229 310

M20 321 435 450 610

M30 1,103 1 495 1,550 2 100

M36 1,917 2 600 2,700 3 675

La page charge ...

Wallenstein BXM32-BXM42 Setup Instructions

Wallenstein BXM32-BXM42 Setup Instructions

dans d''autres langues

Documents connexes