DeWalt D55141 Manuel utilisateur

Marque: DeWalt

Modèle: D55141

Catégorie: Compresseurs d'air

Taper: Manuel utilisateur

D55141

Oil Free Portable Air Compressor

Compresseur d’air portatif sans huile

Compresor de aire sin aceite portátil

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA

DE GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES

DE USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

English

A. On/Off Switch

B. Air Tank Pressure Gauge

C. Regulated Pressure Gauge

D. Pressure Regulator

E. Quick Connects

Pump/Motor Speciﬁ cations

Oil free universal motor

Bore: 1.875 (47.63 mm)

Stroke: 1.25 (31.75 mm)

Voltage: Single 120V

Minimum branch circuit requirement: 15 A

Fuse Type: Time delay

Speciﬁ cations

MODEL

D55141

WEIGHT

30 lbs. (13.61 kg)

HEIGHT

10.5" (266.7 mm)

WIDTH

19.125" (485.8 mm)

LENGTH

21.375 (542.9 mm)

AIR TANK CAPACITY (GALLONS)

2.0 (7.6 liters)

APPROX CUT-IN PRESSURE

120 PSI (827.4 kPa)

APPROX. CUT-OUT PRESSURE

150 PSI (1034.2 kPa)

SCFM @ 100 PSI (689.5 kPa)

1.7

D55141 Air Compressor

FIG. 1

NOT A

STEP

F. Check Valve

G. Safety Valve

H. Air Tank Drain Valve

I. Power Cord Wrap

English

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity

for each signal word. Please read the manual and

pay attention to these symbols.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death

or serious injury.

WARNING: Indicates a potentially hazardous

situation which, if not avoided, could result in death

or serious injury.

CAUTION: Indicates a potentially hazardous

situation which, if not avoided, may result in minor

or moderate injury.

CAUTION: Used without the safety alert symbol

indicates a potentially hazardous situation which, if

not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT

THIS OR ANY D

WALT TOOL, CALL US TOLL FREE AT:

1-800-4-D

WALT (1-800-433-9258)

Important Safety Instructions

WARNING: Do not operate this unit until you read and understand

this instruction manual for safety, operation and maintenance

instructions.

WARNING: Some dust created by power sanding, sawing, grind-

ing, drilling, and other construction activities contains chemicals

known (to the State of California) to cause cancer, birth defects or

other reproductive harm. Some example of these chemicals are:

• lead from lead-based paints

• crystalline silica from bricks and cement and other masonry

products

• arsenic and chromium from chemically-treated lumber

Your risk from these exposures varies, depending on how often

you do this type of work. To reduce your exposure to these chemi-

cals: work in a well ventilated area, and work with approved safety

equipment, al ways wear OSHA/MSHA/NIOSH approved, properly

fit ting face mask or res pi ra tor when us ing such tools.

When using air tools, basic safety precautions should always be fol-

lowed to reduce the risk of of personal injury.

SAVE THESE INSTRUCTION

DANGER: RISK OF EXPLOSION OR FIRE

WHAT CAN HAPPEN HOW TO PREVENT IT

• It is normal for electrical con-

tacts within the motor and

pressure switch to spark.

• Always operate the compres-

sor in a well ventilated area

free of combustible materials,

gasoline, or solvent vapors.

• If electrical sparks from

compressor come into con-

tact with flammable vapors,

they may ignite, causing fire

or explosion.

• If spraying flammable materi-

als, locate compressor at

least 20 feet (6.1 m) away

from spray area. An addi-

tional length of hose may be

required.

• Store flammable materials in

a secure location away from

compressor.

English

• Restricting any of the com-

pressor ventilation openings

will cause serious overheat-

ing and could cause fire.

• Never place objects against or

on top of compressor.

• Operate compressor in

an open area at least 12"

(30.5 cm) away from any

wall or obstruction that would

restrict the flow of fresh air to

the ventilation openings.

• Operate compressor in a

clean, dry well ventilated area.

Do not operate unit indoors or

in any confined area.

• Unattended operation of

this product could result in

personal injury or property

damage. To reduce the risk

of fire, do not allow the

compressor to operate unat-

tended.

• Always remain in attendance

with the product when it is

operating.

• Always disconnect electrical

power by moving the On/ Off

switch in the OFF position

and drain tank daily or after

each use.

DANGER: RISK TO BREATHING (ASPHYXIATION)

WHAT CAN HAPPEN HOW TO PREVENT IT

• The compressed air directly

from your compressor is not

safe for breathing. The air

stream may contain carbon

monoxide, toxic vapors,

or solid particles from the

air tank. Breathing these

contaminant's can cause

serious injury or death.

• Air obtained directly from the

compressor should never be

used to supply air for human

consumption. In order to use air

produced by this compressor

for breathing, suitable filters

and in-line safety equipment

must be properly installed. In-

line filters and safety equipment

used in conjunction with the

compressor must be capable

of treating air to all applicable

local and federal codes prior to

human consumption.

• Sprayed materials such as

paint, paint solvents, paint

remover, insecticides, weed

killers, may contain harmful

vapors and poisons.

• Work in an area with good

cross ventilation. Read and

follow the safety instructions

provided on the label or safety

data sheets for the materials

you are spraying. Always use

certified safety equipment:

OSHA/MSHA/NIOSH

respiratory protection designed

for use with your specific

application.

English

WARNING: RISK OF BURSTING

Air Tank: The air tank on your Air Compressor is designed and may

be UM coded (for units with air tanks greater than 6 inch diameter)

according to ASME Section VIII, Div. 1 rules. All pressure vessels

should be inspected once every two years. To find your state pressure

vessels inspector, look under the Division of Labor and Industries in

the government section of a phone book or call 1-800-4-D

EWALT for

assistance.

The following conditions could lead to a weakening of the air tank, and

result in a violent air tank explosion:

WHAT CAN HAPPEN HOW TO PREVENT IT

• Failure to properly drain

condensed water from

air tank, causing rust and

thinning of the steel air tank.

• Drain air tank daily or after

each use. If air tank develops

a leak, replace it immediately

with a new air tank or replace

the entire compressor.

• Modifications or attempted

repairs to the air tank.

• Never drill into, weld, or make

any modifications to the air

tank or its attachments. Never

attempt to repair a damaged or

leaking air tank. Replace with a

new air tank.

• Unauthorized modifications to

the safety valve or any other

components which control air

tank pressure.

• The air tank is designed

to withstand specific

operating pressures. Never

make adjustments or parts

substitutions to alter the factory

set operating pressures.

Attachments & accessories:

• Exceeding the pressure

rating of air tools, spray guns,

air operated accessories,

tires, and other inflatables

can cause them to explode or

fly apart, and could result in

serious injury.

• Follow the equipment

manufacturers

recommendation and never

exceed the maximum allowable

pressure rating of attachments.

Never use compressor to

inflate small low pressure

objects such as children’s toys,

footballs, basketballs, etc.

WARNING: RISK OF ELECTRICAL SHOCK

WHAT CAN HAPPEN HOW TO PREVENT IT

• Your air compressor is

Like any other electrically

powered device, If it is not

used properly it may cause

electric shock.

• Never operate the compressor

outdoors when it is raining or

in wet conditions.

• Never operate compressor

with protective covers

removed or damaged.

• Repairs attempted by

unqualified personnel can

result in serious injury or

death by electrocution.

• Any electrical wiring or

repairs required on this

product should be performed

by a D

EWALT factory

service center or a D

EWALT

authorized service center in

accordance with national and

local electrical codes.

English

• Electrical Grounding:

Failure to provide adequate

grounding to this product

could result in serious injury

or death from electrocution.

See Grounding

Instructions under

Installation.

• Make certain that the

electrical circuit to which the

compressor is connected

provides proper electrical

grounding, correct voltage and

adequate fuse protection.

WARNING: RISK FROM FLYING OBJECTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• The compressed air stream

can cause soft tissue

damage to exposed skin and

can propel dirt, chips, loose

particles, and small objects

at high speed, resulting in

property damage or personal

injury.

• Always wear certified safety

equipment: ANSI Z87.1 eye

protection (CAN/CSA Z94.3)

with side shields when using

the compressor.

• Never point any nozzle or

sprayer toward any part of

the body or at other people or

animals.

• Always turn the compressor off

and bleed pressure from the

air hose and air tank before

attempting maintenance,

attaching tools or accessories.

WARNING: RISK OF HOT SURFACES

WHAT CAN HAPPEN HOW TO PREVENT IT

• Touching exposed metal such

as the compressor head,

engine head, engine exhaust

or outlet tubes, can result in

serious burns.

• Never touch any exposed

metal parts on compressor

during or immediately after

operation. Compressor will

remain hot for several minutes

after operation.

• Do not reach around

protective shrouds or attempt

maintenance until unit has

been allowed to cool.

WARNING: RISK FROM MOVING PARTS

WHAT CAN HAPPEN HOW TO PREVENT IT

• Moving parts such as the

pulley, flywheel, and belt can

cause serious injury if they

come into contact with you or

your clothing.

• Never operate the compressor

with guards or covers which

are damaged or removed.

• Keep your hair, clothing, and

gloves away from moving parts.

Loose clothes, jewelry, or long

hair can be caught in moving

parts.

• Air vents may cover moving

parts and should be avoided as

well.

English

• Attempting to operate

compressor with damaged or

missing parts or attempting

to repair compressor with

protective shrouds removed

can expose you to moving

parts and can result in

serious injury.

• Any repairs required on this

product should be performed

by a D

EWALT factory service

center or a D

EWALT authorized

service center.

WARNING: RISK OF UNSAFE OPERATION

WHAT CAN HAPPEN HOW TO PREVENT IT

• Unsafe op er a tion of your air

compressor could lead to se ri-

ous in ju ry or death to you or

others.

• Review and understand all

instructions and warnings in

this manual.

• Be come fa mil iar with the

op eration and con trols of the

air compressor.

• Keep operating area clear of all

persons, pets, and obstacles.

• Keep chil dren away from the air

compressor at all times.

• Do not operate the product

when fatigued or under the

influence of alcohol or drugs.

Stay alert at all times.

• Never defeat the safety fea-

tures of this prod uct.

• Equip area of operation with a

fire extinguisher.

• Do not op er ate machine with

missing, broken, or un au tho-

rized parts.

CAUTION: RISK FROM NOISE

WHAT CAN HAPPEN HOW TO PREVENT IT

• Under some conditions and

duration of use, noise from

this product may contribute

to hearing loss.

• Always wear certified safety

equipment: ANSI S12.6

(S3.19) hearing protection.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

FEATURES

ON(I)/OFF SWITCH (I/O)

Place this switch (A) in the ON position to provide

automatic power to the pressure switch and

OFF to remove power at the end of each use.

PRESSURE SWITCH

The pressure switch automatically starts the motor when the air

tank pressure drops below the factory set cut-in pressure. It stops

the motor when the air tank pressure reaches the factory set

cut-out pressure.

English

SAFETY VALVE

If the pressure switch does not shut off the air

compressor at its cut-out pressure setting, the

safety valve (G) will protect against high pres-

sure by popping out at its factory set pressure

(slightly higher than the pressure switch cut-out

setting).

CHECK VALVE

When the air compressor is operating, the

check valve (F) is open, allowing compressed air to enter the air

tank. When the air compressor reaches cut-out pressure, the check

valve closes, allowing air pressure to remain inside the air tank.

TANK PRESSURE GAUGE

The tank pressure gauge (B) indicates

the reserve air pressure in the tank.

OUTLET PRESSURE GAUGE

The outlet pressure gauge (C) indi-

cates the air pressure available at the

outlet side of the regulator. This pres-

sure is controlled by the regulator and

is always less than or equal to the tank pressure.

REGULATOR

The regulator (D) controls the air pressure shown on the outlet

pressure gauge. Turn regulator knob clockwise to increase pres-

sure and counterclockwise to decrease pressure.

UNIVERSAL QUICK CONNECT BODIES

The universal Quick Connect body (E) accepts the three most

popular styles of Quick Connect plugs: Industrial, automotive, and

ARO. The two quick connect bodies allow the use of two tools at the

same time.

DRAIN VALVE

The drain valve (H) is located at the base of the air

tank and is used to drain condensation at the end of

each use.

See Draining Air Tank under

Maintenance.

COOLING SYSTEM

This compressor contains an advanced design cooling system.

It is normal for this fan to blow air through the vent holes in large

amounts. The cooling system is working when air is expelled.

AIR COMPRESSOR PUMP

The pump compresses air into the air tank. Working air is not

available until the compressor has raised the air tank pressure

above that required at the air outlet.

MOTOR OVERLOAD PROTECTOR

The motor has an automatic reset thermal overload protector. If the

motor overheats for any reason, the overload protector will shut

off the motor. The motor must be allowed to cool down before

restarting. The compressor will automatically restart after the motor

cools.

INSTALLATION

Assembly

INSTALLING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 PSI (0 kPa).

2. Grasp the hose at the Quick Connect plug and push the plug

into the Quick Connect body (E).

3. Grasp the hose and pull to ensure coupler is seated.

English

DISCONNECTING HOSES

WARNING: Risk of unsafe operation. Firmly grasp hose in hand

when installing or disconnecting to prevent hose whip.

1. Ensure regulated pressure gauge reads 0 PSI (0 kPa).

2. Pull coupler on Quick Connect body back to release Quick

Connect plug on hose.

Grounding Instructions

WARNING: Risk of Electrical Shock. In the event of a short

circuit, grounding reduces the risk of shock by providing an escape

wire for the electric current. This air compressor must be properly

grounded.

The portable air compressor is equipped with a cord having a

grounding wire with an appropriate grounding plug.

1. The cord set and plug (J) with this unit

contains a grounding pin (L). This plug

MUST be used with a grounded outlet

(K).

IMPORTANT: The outlet being used must

be installed and grounded in accordance

with all local codes and ordinances.

2. Ensure the outlet being used has the same configuration as the

grounded plug. DO NOT USE AN ADAPTER.

3. Inspect the plug and cord before each use. Do not use if there

are signs of damage.

4. If these grounding instructions are not completely understood, or

if in doubt as to whether the compressor is properly grounded,

have the installation checked by a qualified electrician.

DANGER: Risk of Electrical Shock. IMPROPER GROUNDING

CAN RESULT IN ELECTRICAL SHOCK.

Do not modify the plug provided. If it does not fit the available out-

let, a correct outlet should be installed by a qualified electrician.

Repairs to the cord set or plug MUST be made by a qualified

electrician.

Extension Cords

Using extension cords is not recommended. The use of extension

cords will cause voltage to drop resulting in power loss to the motor

and overheating.

Instead of using an extension cord, increase the working reach of

the air hose by attaching another length of hose to its end. Attach

additional lengths of hose as needed.

If an extension cord must be used, be sure it is:

• a 3-wire extension cord that has a 3-blade grounding plug, and

a 3-slot receptacle that will accept the plug on the product

• in good condition

• no longer than 50 feet (15,2 m)

• 14 gauge (AWG) or larger. (Wire size increases as gauge num-

ber decreases. 12 AWG and 10 AWG may also be used. DO

NOT USE 16 OR 18 AWG.)

Voltage and Circuit Protection

Refer to the Voltage and Minimum Branch Circuit Requirements under

Pump/Motor Specifications.

CAUTION: Certain air compressors can be operated on a

15 amp circuit if the following conditions are met.

• Voltage supply to circuit must comply with the National Electrical

Code.

• Circuit is not used to supply any other electrical needs.

• Extension cords comply with specifications.

• Circuit is equipped with a 15 amp circuit breaker or 15 amp

time delay fuse. NOTE: If compressor is connected to a circuit

protected by fuses, use only time delay fuses. Time delay fuses

should be marked “D” in Canada and “T” in the US.

English

If any of the above conditions cannot be met, or if operation of the

compressor repeatedly causes interruption of the power, it may be

necessary to operate it from a 20 amp circuit. It is not necessary

to change the cord set.

Compatibility

Air tools and accessories that are run off the compressor must be

compatible with petroleum-based products. If you suspect that a

material is not compatible with petroleum products, an air line filter

for removal of moisture and oil vapor in compressed air is required.

NOTE: Always use an air line filter to remove moisture and oil vapor

when spraying paint.

Location

Place the air compressor in a clean, dry and well ventilated area at

least 12" (304.8 mm) away from the wall or other obstructions that

will interfere with the flow of air. Keep the compressor away from

areas that have dirt and/or volatile fumes in the atmosphere. These

impurities may clog the intake filter and valves, causing inefficient

operation.

The air compressor pump and shroud are designed to allow for

proper cooling. The ventilation openings on the compressor are

necessary to maintain proper operating temperature. Do not place

rags or other containers on or near these openings.

Place the air compressor on a flat surface resting on the rubber

feet.

NOISE CONSIDERATIONS

Consult local officials for information regarding acceptable noise

levels in your area. To reduce excessive noise, use vibration mounts

or silencers, relocate the unit or construct total enclosures or baffle

walls. Contact a D

WALT service center or call 1-800-4-D

WALT for

assistance.

ELECTRICAL

Refer to all safety instructions before using unit. Observe extension

cord safety instructions if necessary. Always move the On/Off

switch (A) to the OFF position before removing the plug from the

outlet.

TRANSPORTING

When transporting the compressor in a vehicle, trailer, etc., ensure

that the tank is drained and the unit is secured. Use care when driv-

ing to avoid tipping the unit over in the vehicle. Damage can occur to

the compressor or surrounding items if the compressor is tipped.

MOVING

When moving the compressor, grasp the handle and carry the com-

pressor as close to the body as possible.

WARNING: Ensure proper footing and use caution when carrying

compressor to avoid a loss of balance.

PREPARATION FOR USE

Pre-Start Checklist (Fig. 1)

Ensure the On/Off switch (A) is in the OFF position.

Plug the power cord into the correct branch circuit receptacle.

See

Voltage and Circuit Protection under Installation.

3. Ensure air tank is drained, see Draining Air Tank under

Maintenance.

4. Ensure the drain valve (H) is closed.

5. Ensure safety valve (G) is functioning properly, see Checking

Safety Valve under Maintenance.

6. Turn regulator knob (D) counterclockwise until fully closed. Ensure

regulated pressure gauge reads 0 PSI (0 kPa).

7. Attach hose and accessories.

English

WARNING: Risk of Bursting. Too much air pressure causes a

hazardous risk of bursting. Check the manufacturer’s maximum

pressure rating for air tools and accessories. The regulator outlet

pressure must never exceed the maximum pressure rating.

Initial Set-up

(Fig. 1)

WARNING: Do not operate this unit until you read and understand

this instruction manual for safety, operation and maintenance

instructions.

BREAK-IN PROCEDURE

WARNING: Risk of property damage. Serious damage may result

if the following break-in instructions are not closely followed.

This procedure is required before the air compressor is put into

service for the first time and when the check valve or a compressor

pump/motor has been replaced.

1. Ensure the On/Off switch (A) is in the OFF position.

Plug the power cord into the correct branch circuit receptacle.

See

Voltage and Circuit Protection under Installation.

3. Open the drain valve (counter-clockwise) fully to permit air to

escape and prevent air pressure build up in the air tank during

the break-in period.

4. Move the On/Off switch to the ON position. The compressor will

start.

5. Run the compressor for 15 minutes.

6. After 15 minutes, close the drain valve by turning clockwise.

The tank will fill to cut-out pressure and the motor will stop.

7. Compressed air will be available until it is used or bled off.

OPERATING PROCEDURES

Start-up (Fig. 1)

1. Follow Pre-Start Checklist under Preparation for Use.

2. Move the On/Off switch to the ON position and allow tank pres-

sure to build. Motor will stop when tank pressure reaches

cut-out pressure.

CAUTION: Risk of unsafe operation. Compressed air from the unit

may contain wa ter condensation and oil mist. Do not spray un fil tered

air at an item that could be damaged by moisture. Some air op er-

ated tools or de vic es may require filtered air. Read the in struc tions

for the air tool or device.

3. Adjust regulator (D) to desired setting. See Regulator under

Features.

Shut-down (Fig. 1)

1 Move On/Off switch (A) is in the OFF position. NOTE: If finished

using compressor, follow Steps 2 - 6.

NOTE: When the unit has been turned off, it is normal to hear a short

hiss of air being released.

2. Turn regulator knob (D) counterclockwise until fully closed. Ensure

regulated pressure gauge reads 0 PSI (0 kPa).

3. Remove hose and accessory.

4. Drain the air tank,

see Draining Air Tank under Maintenance

Ensure air tank pressure gauge reads 0 PSI (0 kPa).

WARNING: Risk of bursting. Drain air tank daily. Water will con-

dense in air tank. If not drained, water will corrode and weaken the

air tank causing a risk of air tank rupture.

5. Allow the compressor to cool down.

6. Wipe air compressor clean and store in a safe, non-freezing area.

English

MAINTENANCE

The following procedures must be followed when maintenance or

service is performed on the air compressor.

1. Ensure On/Off switch is in the OFF position.

2. Remove air compressor plug from outlet.

3. Drain air tank.

4. Allow air compressor to cool down before starting service.

NOTE: All compressed air systems contain maintenance parts (e.g.,

oil, filters, separators) that are periodically replaced. These used parts

may contain substances that are regulated and must be disposed of in

accordance with local, state, and federal laws and regulations.

NOTE: Take note of the positions and locations of parts during

disassembly to make reassembly easier.

NOTE: Any service operations not included in this section should

be performed by a D

WALT factory service center or a D

WALT

authorized service center.

Maintenance Chart

Procedure Before Each

Use

Daily or after each

use

Check safety valve

Drain air tank

Checking Safety Valve

WARNING: Risk of bursting. If the safety valve does not work

properly, over-pressurization may occur, causing air tank rupture or

an explosion.

Before starting compressor, pull the ring on the safety valve to

make sure that the safety valve operates freely. If the valve is

stuck or does not operate smoothly, it must be replaced with the

same type of valve.

Draining Air Tank (Fig. 1)

WARNING: Risk of unsafe operation. Risk from noise. Air tanks

contain high pressure air. Keep face and other body parts away from

outlet of drain. Use safety glasses when draining as debris can be

kicked up into face. Use ANSI S12.6 (S3.19) ear protection as air flow

noise is loud when draining.

NOTE: All compressed air systems generate condensate that

accumulates in any drain point (e.g., tanks, filter, aftercoolers,

dryers). This condensate contains lubricating oil and/or substances

which may be regulated and must be disposed of in accordance with

local, state, and federal laws and regulations.

1. Ensure On/Off switch (A) is in the OFF position.

2. Move compressor into an inclined position so drain valve (H) is

at the lowest point (this will assist in removing moisture, dirt, etc.

from air tanks)

3. Place a suitable container under the drain valve to catch

discharge.

4. Grasp black lever on drain valve.

5. Slowly rotate lever to gradually bleed air from air tank.

6. When air tank pressure gauge reads 10 PSI (275.1 kPa), rotate

valve to the fully open position.

7. Close drain valve when finished.

ACCESSORIES

Recommended accessories for use with your tool are available

for purchase from your local dealer or authorized service center. If

you need assistance in locating any accessory for your tool, please

contact D

WALT Industrial Tool Co., 701 East Joppa Road, Baltimore,

MD 21286, call 1-800-4-D

WALT (1-800-433-9258) or visit our

website www.dewalt.com.

English

CAUTION: The use of any other accessory not recommended for

use with this tool could be hazardous. Use only accessories rated

equal to or higher than the rating of the air compressor.

SERVICE INFORMATION

Please have the following information available for all service calls:

Model Number ____________ Serial Number _________________

Date and Place of Purchase ______________________________

Repairs

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment should be performed by a D

WALT factory service

center, a D

WALT authorized service center or other qualified

service personnel. Always use identical replacement parts.

Full One Year Warranty

DEWALT heavy duty industrial tools are warranted for one year from

date of purchase. We will repair, without charge, any defects due

to faulty materials or workmanship. For warranty repair information,

call 1-800-4-D

WALT. This warranty does not apply to accessories

or damage caused where repairs have been made or attempted by

others. This warranty gives you specific legal rights and you may

have other rights which vary in certain states or provinces.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained either in the packaging, call

the local company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-D

WALT for a free

replacement.

English

GLOSSARY

CFM: Cubic feet per minute.

SCFM: Standard cubic feet per minute; a unit of measure of air delivery.

PSI: Pounds per square inch; a unit of measure of pressure.

Code Certification: Products that bear one or more of the following marks: UL, CUL, ETL, CETL, have been evaluated by OSHA certified

independent safety laboratories and meet the applicable Underwriters Laboratories Standards for Safety.

Cut-In Pressure: While the motor is off, air tank pressure drops when accessory is used. When the tank pressure drops to a certain low

level the motor will restart automatically. The low pressure at which the motor automatically restarts is called cut-in pressure.

Cut-Out Pressure: When an air compressor is turned on and begins to run, air pressure in the air tank begins to build. It builds to a

certain high pressure before the motor automatically shuts off, protecting your air tank from pressure higher than its capacity. The high

pressure at which the motor shuts off is called cut-out pressure.

Branch Circuit: The circuit carrying electricity from electrical panel to outlet.

Duty Cycle: This air compressor pump is capable of running continuously. However, to prolong the life of your air compressor, it is

recommended that a 50%-75% average duty cycle be maintained; that is, the air compressor pump should not run more than 30-

45 minutes in any given hour.

English

Troubleshooting Guide

This section provides a list of the more frequently encountered malfunctions, their causes and corrective actions. The operator or maintenance

personnel can perform some corrective actions, and others may require the assistance of a qualified D

EWALT technician or your dealer.

Problem Code

Excessive air tank pressure-safety valve pops off ......................................................................1,2

Air leaks ....................................................................................................................................3

Air leaks in air tank or at air tank welds ....................................................................................4

Air leaks between head and valve plate ....................................................................................5

Air leaks from safety valve .........................................................................................................6

Knocking Noise ..........................................................................................................................6

Pressure reading on the regulated pressure gauge drops when an accessory is used ...........7

Compressor is not supplying enough air to operate accessories..............................................8,9,10,11,12

Regulator knob has continuous air leak ....................................................................................13

Regulator will not shut off air outlet ...........................................................................................13

Troubleshooting Codes

CODE POSSIBLE CAUSE POSSIBLE SOLUTION

1 Pressure switch does not shut off motor when compressor

reaches cut-out pressure

Set the On/Off switch to OFF, if the unit does not shut

off contact a D

WALT factory service center or a D

WALT

authorized service center.

Pressure switch cut-out too high

Contact a D

WALT factory service center or a D

WALT

authorized service center.

Tube fittings are not tight enough Tighten fittings where air can be heard escaping. Check

fittings with soapy water solution. Do Not Overtighten.

English

CODE POSSIBLE CAUSE POSSIBLE SOLUTION

4 Defective air tank Air tank must be replaced. Do not repair the leak.

WARNING: Risk of bursting. Do not drill into, weld or

otherwise modify air tank or it will weaken. The air tank can

rupture or explode.

5 Leaking seals Contact a D

WALT factory service center or a D

WALT

authorized service center.

6 Defective safety valve Operate safety valve manually by pulling on ring. If valve

still leaks, it must be replaced.

Regulator is not adjusted correctly for accessory being

used

It is normal for some pressure drop to occur when an acces-

sory is used, adjust the regulator as instructed in Regulator

under Features if pressure drop is excessive.

NOTE: Adjust the regulated pressure under flow conditions

while accessory is being used.

8 Prolonged excessive use of air Decrease amount of air usage.

9 Compressor is not large enough for accessory Check the accessory air requirement. If it is higher than

the CFM or pressure supplied by your air compressor, a

larger compressor is needed to operate accessory.

10 Hole in air hose Replace air hose.

11 Check valve restricted Remove, clean or replace.

12 Air leaks Tighten fittings.

13 Regulator is damaged Replace.

Français

Compresseur d’air, modèle D55141

FIG. 1

PAS UNE

ÉTAPE

A. Interrupteur Marche/Arrêt

B. Manomètre du réservoir d’air

C. Manomètre régulé

D. Régulateur de pression

E. Branchements rapides

F. Clapet

G. Soupape de sûreté

H. Soupape de purge du

réservoir d’air

I. Rembobineur de cordon

d’alimentation

Fiche technique de la pompe/du moteur

Moteur universel sans huile

Alésage : 47,63 mm (1,875 po)

Course : 31,75 mm (1,25 po)

Tension : monophasé, 120V

Exigence minimale du circuit de dérivation : 15 A

Type de fusible : temporisation

Fiche technique

MODÈLE

D55141

POIDS

13,61 kg (30 lbs.)

HAUTEUR

266,7 mm (10,5 po)

LARGEUR

485,8 mm (19,125 po)

LONGUEUR

542,9 mm (21,375 po)

CAPACITÉ DU RÉSERVOIR D’AIR

(GALLONS)

2,0 (7,6 liters)

PRESSION D’ENCLENCHEMENT

APPROX.

827,4 kPa (120 PSI)

ENV. PRESSION DE DÉCLENCHEMENT

1034,2 kPa (150 PSI)

PCMS (SCFM) @ 100 PSI (689,5 kPa)

1,7

Français

Déﬁ nitions : lignes directrices en

matière de sécurité

Les définitions ci-dessous décrivent le niveau de gravité pour

chaque symbole. Veuillez lire le mode d’emploi et porter une atten-

tion particulière à ces symboles.

DANGER : Indique une situation dangereuse imminente qui, si

elle n’est pas évitée, causera la mort ou des blessures graves.

AVERTISSEMENT :

Indique une situation potentiellement dan-

gereuse qui, si elle n’est pas évitée, pourrait se solder par un

décès ou des blessures graves.

MISE EN GARDE : Indique une situation potentiellement dan-

gereuse qui, si elle n’est pas évitée pourrait se solder par des

blessures mineures ou modérées.

MISE EN GARDE : Utilisé sans le symbole d’alerte à la sécurité,

indique une situation potentiellement dangereuse qui, si elle n'est

pas évitée pourrait se solder par des dommages à la propriété.

POUR TOUTES QUESTIONS OU COMMENTAIRES RELATIFS(VES)

À L’OUTIL OU À PROPOS DE TOUT AUTRE OUTIL D

WALT,

COMPOSER SANS FRAIS LE : 1-800-4-D

EWALT

(1-800-433-9258)

Directives de sécurité importantes

AVERTISSEMENT : Ne pas utiliser cet appareil avant d’avoir lu

et compris le mode d’emploi ainsi que l’intégralité des directives de

sécurité, d’utilisation et d’entretien.

AVERTISSEMENT : Nertaines poussières produites par les travaux

de ponçage, sciage, meulage, perçage et autres peuvent contenir des

produits chimiques pouvant (selon l’état de Californie) causer le cancer,

des anomalies congénitales ou d’autres problèmes liés aux fonctions

reproductrices. Voici quelques exemples de ces produits chimiques :

• le plomb contenu dans les peintures à base de plomb;

• la silice cristalline provenant de la brique, du ciment et d’autres

produits de maçonnerie;

• l’arsenic et chrome provenant de bois traité chimiquement.

Les risques reliés à l’exposition à ces poussières varient selon la

fréquence à laquelle l’utilisateur travaille avec ce type de matériaux.

Pour réduire votre exposition à ces produits chimiques : travailler dans

un endroit bien ventilé et porter un équipement de sécurité approuvé

par l’OSHA/MSHA/NIOSH comme un masque anti-poussières

spécialement adapté ou un respirateur lors de l’utilisation de ces

outils.

Lors de l’utilisation d’outils pneumatiques, des précautions de base

en matière de sécurité doivent être suivies afin de réduire le risque de

blessure personnelle.

CONSERVER CES DIRECTIVES

AVERTISSEMENT : Risque d’explosion ou d’incendie

CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER

• Il est normal que des

contacts électriques dans le

moteur et le manocontacteur

fassent une étincelle.

• Faites toujours fonctionner

le compresseur dans une

zone bien aérée sans matière

combustible, essence ou

vapeur de solvant.

Français

• Si une étincelle électrique

provenant du compresseur

entre en contact avec des

vapeurs inflammables,

elle peut s’enflammer et

causer un incendie ou une

explosion.

• Si vous aspergez des

matériaux inflammables,

placez le compresseur à

au moins 6,1 m (20 pieds)

de la zone pulvérisée. Il est

possible que vous ayez besoin

d’une longueur de tuyau

additionnelle.

• Entreposez les matières

inflammables dans un

endroit sécuritaire, éloigné du

compresseur.

• Le fait de limiter les

ouvertures d’aération de

compresseur causera une

importante surchauffe et

pourrait causer un incendie.

• Ne placez jamais des objets

contre le compresseur ou sur

celui-ci.

• Faites fonctionner le

compresseur dans un endroit

aéré à au moins 30,5 cm

(12 po) du mur ou de

l’obstruction qui pourrait limiter

le débit d’air frais dans les

ouvertures d’aération.

• Faites fonctionner le

compresseur dans un endroit

propre, sec et bien aéré.

Ne pas utiliser l’appareil à

l’intérieur ou dans un endroit

exigu.

• Le fonctionnement de ce

produit sans surveillance

pourrait se solder par des

blessures personnelles

ou des dommages à la

propriété. Afin de réduire

le risque d’incendie, ne

pas laisser le compresseur

fonctionner sans surveillance.

• Être toujours présent lorsque

le produit est en marche.

• Toujours débrancher le cordon

d’alimentation en mettant

l’interrupteur marche/arrêt en

position ARRÊT et purger le

réservoir quotidiennement ou

après chaque utilisation.

DANGER : RISQUE REPIRATOIRE (ASPHYXIE)

CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER

• Il est dangereux de respirer

l’air comprimé sortant du

compresseur. Le flux d’air

peut contenir du monoxyde

de carbone, des vapeurs

toxiques ou des particules

solides provenant du réservoir

d’air. L’inhalation de ces

contaminants peut provoquer

de sérieuses blessures, voire

un décès.

• L’air qui s’obtient directement du

compresseur ne devrait jamais

être utilisé pour alimenter l’air

destiné à la consommation

humaine. Pour utiliser l’air

produit par le compresseur

pour la respiration, installer

correctement des filtres

convenables et un équipement

de sécurité en ligne. Les

filtres en ligne et l’équipement

de sécurité utilisés avec

le compresseur doivent

être capables de traiter l’air

conformément à tous les codes

locaux et fédéraux en vigueur

avant toute consommation

humaine.

Français

• Les matériaux vaporisés

comme la peinture, les

solvants de peinture, les

décapants, les insecticides,

les herbicides, pourraient

contenir des vapeurs nocives

et du poison.

• Travailler dans un endroit

ayant une bonne ventilation

transversale. Lire et respecter

les directives en matière

de sécurité imprimées sur

l’étiquette ou les fiches

signalétiques des matériaux qui

sont pulvérisés. Toujours utiliser

un équipement de sécurité

homologué : une protection

respiratoire conforme aux

normes OSHA/MSHA/NIOSH,

conçue spécifiquement pour

une utilisation particulière.

AVERTISSEMENT : RISQUE D’ÉCLATEMENT

Réservoir d’air : le réservoir dont est doté le compresseur d’air porte le

code « UM » (dans le cas d’appareils munis de réservoirs supérieurs à

152 mm (6 po) de diamètre) et il est conçu conformément à la section

VII Div. 1 de l’ASME. Tous les récipients sous pression devraient être

inspectés une fois tous les deux ans. Pour localiser l’inspecteur des

récipients sous pression de votre région, consulter la section appropriée

des organismes gouvernementaux de l’annuaire téléphonique ou

composer le 1-800-4-D

EWALT pour obtenir de l’aide.

Les conditions indiquées ci-après pourraient affaiblir le réservoir d’air et

se solder par une violente explosion de celui-ci :

CE QUI PEUT SE PRODUIRE COMMENT L’ÉVITER

• L’eau condensée n’est pas

correctement vidangée du

réservoir d’air provoquant

ainsi la formation de rouille

et un amincissement du

réservoir d’air en acier.

• Vidanger le réservoir d’air

quotidiennement ou après

chaque utilisation. Si le réservoir

présente une fuite, le remplacer

immédiatement par un nouveau

réservoir d’air ou par un

nouveau compresseur.

• Modifications apportées au

réservoir d’air ou tentatives de

réparation.

• Ne jamais percer un trou

dans le réservoir d’air ou ses

accessoires, y faire de la

soudure ou y apporter quelque

modification que ce soit. Ne

jamais essayer de réparer un

réservoir d’air endommagé ou

avec des fuites. Le remplacer

par un nouveau réservoir d’air.

• Des modifications non

autorisées de la soupape

de sûreté ou de tous autres

composants qui régissent la

pression du réservoir d’air.

• Le réservoir d’air a été conçu

pour supporter des pressions

spécifiques de fonctionnement.

Ne faites jamais effectuer de

réglages ou de substitutions de

pièces en vue de modifier les

pressions de fonctionnement

réglées en usine.

La page charge ...

DeWalt D55141 Manuel utilisateur

Marque: DeWalt

Modèle: D55141

Catégorie: Compresseurs d'air

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: DeWalt D55141 User manual
español: DeWalt D55141 Manual de usuario

DeWalt D55141 Manuel utilisateur

DeWalt D55141 Manuel utilisateur

dans d''autres langues

Documents connexes