Hitachi CR 18DV Manuel utilisateur

INSTRUCTIONS DE SECURITE ET MODE D’EMPLOI

AVERTISSEMENT

Une utilisation INCORRECTE OU DANGEREUSE de cet outil motorisé peut entraîner

la mort ou de sérieuses blessures corporelles!

Ce mode d’emploi contient d’importantes informations à propos de la sécurité de

ce produit. Prière de lire et de comprendre ce mode d’emploi AVANT d’utiliser

l’outil motorisé. Garder ce mode d’emploi à la disponibilité des autres utilisateurs

et propriétaires avant qu’ils utilisent l’outil motorisé. Ce mode d’emploi doit être

conservé dans un endroit sûr.

SAFETY INSTRUCTIONS AND INSTRUCTION MANUAL

WARNING

IMPROPER OR UNSAFE use of this power tool can result in death or serious bodily

injury!

This manual contains important information about product safety. Please read

and understand this manual BEFORE operating the power tool. Please keep this

manual available for other users and owners before they use the power tool. This

manual should be stored in safe place.

CR 18DV

INSTRUCCIONES DE SEGURIDAD Y MANUAL DE INSTRUCCIONES

ADVERTENCIA

¡La utilización INAPROPIADA O PELIGROSA de esta herramienta eléctrica puede

resultar en lesiones de gravedad o la muerte!

Este manual contiene información importante sobre la seguridad del producto.

Lea y comprenda este manual ANTES de utilizar la herramienta eléctrica. Guarde

este manual para que puedan leerlo otras personas antes de utilizar la herramienta

eléctrica. Este manual debe ser guardado en un lugar seguro.

Model Cordless Reciprocating Saw

Modèle Scie alternative à batterie

Modelo Sierra sable a batería

2

English

TABLE DES MATIERES

ÍNDICE

Français

Español

Page

IMPORTANT SAFETY INFORMATION .............. 3

MEANINGS OF SIGNAL WORDS ...................... 3

SAFETY .................................................................... 4

GENERAL SAFETY RULES – FOR ALL

BATTERY OPERATED TOOLS..................... 4

SPECIFIC SAFETY RULES AND SYMBOLS....... 6

IMPORTANT SAFETY INSTRUCTIONS FOR USE

OF THE CORDLESS RECIPROCATING SAW

.... 7

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CHARGER ............................. 8

IMPORTANT SAFETY INSTRUCTIONS

FOR USE OF THE BATTERY AND

BATTERY CHARGER...................................... 9

FUNCTIONAL DESCRIPTION.................................. 11

MODEL ......................................................... 11

NAME OF PARTS ......................................... 11

SPECIFICATIONS ......................................... 12

Page

ASSEMBLAGE ET FONCTIONNEMENT ................ 37

APPLICATIONS ................................................... 37

MÉTHODE DE RETRAIT ET D’INSTALLATION

DE LA BATTERIE .......................................... 37

MÉTHODE DE RECHARGE ................................. 37

AVANT L’UTILISATION ...................................... 40

AVANT L’OPERATION ........................................ 41

COMMENT UTILISER LA SCIE

ALTERNATIVE À BATTERIE ........................ 43

ENTRETIEN ET INSPECTION .................................. 47

Page

ASSEMBLY AND OPERATION ............................... 13

APPLICATIONS ................................................... 13

REMOVAL AND INSTALLATION METHOD

OF BATTERY ................................................ 13

CHARGING METHOD ......................................... 13

BEFORE USE ....................................................... 16

PRIOR TO OPERATION ....................................... 17

HOW TO USE THE CORDLESS

RECIPROCATING SAW................................ 19

MAINTENANCE AND INSPECTION ....................... 22

CONTENTS

English

Page

INFORMATIONS IMPORTANTES DE SÉCURITÉ

...... 27

SIGNIFICATION DES MOTS D’AVERTISSEMENT

.... 27

SECURITE ................................................................ 28

REGLES GENERALE DE SECURITE – POUR TOUS

LES OUTILS FONCTIONNANT SUR BATTERIE

... 28

REGLES DE SECURITE SPECIFIQUES ET SYMBOLES

.... 30

CONSIGNES DE SÉCURITÉ IMPORTANTES POUR

L'UTILISATION DU SCIE ALTERNATIVE

À BATTERIE

...................................................... 31

CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR LE CHARGEUR DE BATTERIE .......... 32

CONSIGNES DE SÉCURITÉ IMPORTANTES POUR L’UTILISATION

DE LA BATTERIE ET DU CHARGEUR DE BATTERIE

........... 33

DESCRIPTION FONCTIONNELLE ........................... 35

MODELE .............................................................. 35

NOM DES PARTIES ............................................ 35

SPECIFICATIONS ................................................ 36

Página

MONTAJE Y OPERACIÓN ...................................... 62

APLICACIONES ................................................... 62

MÉTODO DE EXTRACCIÓN E INSTALACIÓN

DE LA BATERÍA............................................ 62

MÉTODO DE CARGA .......................................... 62

ANTES DE LA UTILIZACIÓN .............................. 65

ANTES DE LA OPERACIÓN ................................ 66

COMO USAR LA SIERRA SABLE

A BATERÍA ................................................... 68

MANTENIMIENTO E INSPECCIÓN ........................ 72

Página

INFORMACIÓN IMPORTANTE SOBRE SEGURIDAD

.. 52

SIGNIFICADO DE LAS PALABRAS DE SEÑALIZACIÓN

.. 52

SEGURIDAD............................................................. 53

NORMAS GENERALES DE SEGURIDAD – PARA TODAS

LAS HERRAMIENTAS ALIMENTADAS CON BATERÍA

.. 53

NORMAS Y SÍMBOLOS ESPECÍFICOS DE SEGURIDAD

.... 55

INSTRUCCIONES IMPORTANTES PARA LA

UTILIZACIÓN DEL SIERRA SABLE

A BATTERÍA

................................................... 56

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA EL CARGADOR DE BATERÍAS

.................. 57

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

PARA LA BATERÍA Y EL CARGADOR DE BATERÍAS

... 58

DESCRIPCIÓN FUNCIONAL.................................... 60

MODELO .............................................................. 60

NOMENCLATURA............................................... 60

ESPECIFICACIONES............................................ 61

3

English

IMPORTANT SAFETY INFORMATION

Read and understand all of the safety precautions, warnings and operating instructions in

the Instruction Manual before operating or maintaining this power tool.

Most accidents that result from power tool operation and maintenance are caused by the

failure to observe basic safety rules or precautions. An accident can often be avoided by

recognizing a potentially hazardous situation before it occurs, and by observing appropriate

safety procedures.

Basic safety precautions are outlined in the “SAFETY” section of this Instruction Manual

and in the sections which contain the operation and maintenance instructions.

Hazards that must be avoided to prevent bodily injury or machine damage are identified by

WARNINGS on the power tool and in this Instruction Manual.

NEVER use this power tool in a manner that has not been specifically recommended by

HITACHI.

MEANINGS OF SIGNAL WORDS

WARNING indicates a potentially hazardous situations which, if ignored, could result in

death or serious injury.

CAUTION indicates a potentially hazardous situations which, if not avoided, may result in

minor or moderate injury, or may cause machine damage.

NOTE emphasizes essential information.

4

English

SAFETY

GENERAL SAFETY RULES – FOR ALL BATTERY OPERATED TOOLS

WARNING:Read and understand all instructions.

Failure to follow all instructions listed below, may result in electric shock,

fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

1. Work Area

(1) Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

(2) Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases, or dust. Power tools create sparks which may ignite the

dust of fumes.

(3) Keep bystanders children, and visitors away while operating a power tool.

Distractions can cause you to lose control.

2. Electrical Safety

(1) A battery operated tool with integral batteries or a separate battery pack must be

recharged only with the specified charger for the battery.

A charger that may be suitable for one type of battery may create a risk of fire when

used with another battery.

(2) Use battery operated tool only with specifically designed battery pack.

Use of any other batteries may create a risk of fire.

3. Personal Safety

(1) Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in

serious personal injury.

(2) Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep

your hair, clothing and gloves away from moving parts. Loose clothes, jewelry, or

long hair can be caught in moving parts.

(3) Avoid accidental starting. Be sure switch is off position before inserting battery.

Carrying tools with your finger on the switch or inserting the battery pack into a

tool with the switch on invites accidents.

(4) Remove adjusting keys or wrenches before turning the tool on. A wrench or a key

that is left attached to a rotating part of the tool may result in personal injury.

(5) Do not overreach. Keep proper footing and balance at all times. Proper footing and

balance enable better control of the tool in unexpected situations.

(6) Use safety equipment. Always wear eye protection. Dust mask, non-skid safety

shoes, hard hat, or hearing protection must be used for appropriate conditions.

5

English

4. Tool Use and Care

(1) Use clamps or other practical way to secure and support the workpiece to a stable

platform. Holding the work by hand or against your body is unstable and may lead

to loss of control.

(2) Do not force tool. Use the correct tool for your application. The correct tool will do

the job better and safer at the rate for which it is designed.

(3) Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled

with the switch is dangerous and must be repaired.

(4) Disconnect battery pack from tool or place the switch in the locked or off position

before making any adjustments, changing accessories, or storing the tools. Such

preventive safety measures reduce the risk of starting the tool accidentally.

(5) Store idle tools out of reach of children and other untrained persons. Tools are

dangerous in the hands of untrained users.

(6) When battery pack is not in use, keep it away from other metal objects like: paper

clips, coins, keys, nails, screws, or other small metal objects that can make a

connection from one terminal to another.

Shorting the battery terminals together may cause sparks, burns, or a fire.

(7) Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained

tools, with sharp cutting edges are less likely to bind and are easier to control.

(8) Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tool's operation. If damaged, have the tool

serviced by a HITACHI authorized service center before using. Many accidents are

caused by poorly maintained tools.

(9) Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool, may become hazardous when used

on another tool.

5. Service

(1) Tool service must be performed only by a HITACHI authorized service center. Service

or maintenance performed by unqualified personnel could result in a risk of injury.

(2) When servicing a tool, use only identical replacement parts. Follow instructions in

the Maintenance section of this manual. Use of unauthorized parts or failure to

follow Maintenance Instruction may create a risk of electric shock or injury.

WARNING:

Some dust created by power sanding, sawing, grinding, drilling, and other construction

activities contains chemicals known [to the State of California] to cause cancer, birth

defects or other reproductive harm. Some examples of these chemicals are:

● Lead from lead-based paints,

● Crystalline silica from bricks and cement and other masonry products, and

● Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area, and

work with approved safety equipment, such as those dust masks that are specially

designed to filter out microscopic particles.

6

English

SPECIFIC SAFETY RULES AND SYMBOLS

1. Hold tools by insulated gripping surfaces when performing an operation where the

tool may contact hidden wiring. Contact with a “live” wire will make exposed metal

parts of the tool “live” and shock the operator.

2. Never touch moving parts.

Never place your hands, fingers or other body parts near the tool’s moving parts.

3. Never operate without all guards in place.

Never operate this tool without all guards or safety features in place and in proper

working order. If maintenance or servicing requires the removal of a guard or safety

feature, be sure to replace the guard or safety feature before resuming operation of the

tool.

4. Use right tool.

Don’t force small tool or attachment to do the job of a heavy-duty tool.

Don’t use tool for purpose not intended —for example— don’t use circular saw for

cutting tree limbs or logs.

5. Never use a power tool for applications other than those specified.

Never use a power tool for applications other than those specified in the Instruction

Manual.

6. Handle tool correctly.

Operate the tool according to the instructions provided herein. Do not drop or throw

the tool. Never allow the tool to be operated by children, individuals unfamiliar with its

operation or unauthorized personnel.

7. Definitions for symbols used on this tool

V ............. volts

—

---

............ direct current

Hz ........... hertz

A............. amperes

no .......... no load speed

---/min .... revolutions or reciprocation per minute

8. Keep all screws, bolts and covers tightly in place.

Keep all screws, bolts, and plates tightly mounted. Check their condition periodically.

9. Do not use power tools if the plastic housing or handle is cracked.

Cracks in the tool’s housing or handle can lead to electric shock. Such tools should not

be used until repaired.

10. Blades and accessories must be securely mounted to the tool.

Prevent potential injuries to youself or others. Blades, cutting implements and

accessories which have been mounted to the tool should be secure and tight.

11. Never use a tool which is defective or operating abnormally.

If the tool appears to be operating unusually, making strange noises, or otherwise

appears defective, stop using it immediately and arrange for repairs by a Hitachi

authorized service center.

12. Carefully handle power tools.

Should a power tool be dropped or struck against hard materials inadvertently, it may

be deformed, cracked, or damaged.

7

English

13. Do not wipe plastic parts with solvent.

Solvents such as gasoline, thinner benzine, carbon tetrachloride, and alcohol may

damage and crack plastic parts. Do not wipe them with such solvents.

Wipe plastic parts with a soft cloth lightly dampened with soapy water and dry

thoroughly.

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE

CORDLESS RECIPROCATING SAW

WARNING:Death or serious bodily injury could result from improper or unsafe use

of the Cordless Reciprocating Saw. To avoid these risks, follow these

basic safety instructions:

1. NEVER touch the tool blade with bare hands after operation.

2. ALWAYS wear ear protectors when using for extended periods.

3. ALWAYS wear eye protectors during operation.

4. ALWAYS be careful with buried object such as an underground, wiring.

Touching these active wiring or electric cable with this tool, you may receive an electric

shock.

Comfirm if there are any buried object such as electric cable within the wall, floor or

ceiling where you are going to operate here after.

8

English

IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CHARGER

WARNING:Death or serious bodily injury could result from imprper or unsafe use

of battery chargers. To avoid these risks, follow these basic safety

instructions:

READ ALL INSTRUCTIONS

1. This manual contains important safety and operating instructions for battery charger

Model UC 24YFA.

2. Before using battery charger, read all instructions and cautionary markings on (1) battery

charger, (2) battery, and (3) product using battery.

3. To reduce risk of injury, charge HITACHI rechargeable battery type EB1820. Other type

of batteries may burst causing personal injury and damage.

4. Do not expose battery charger to rain or snow.

5. Use of an attachment not recommended or sold by the battery charger manufacturer

may result in a risk of fire, electric shock, or injury to persons.

6. To reduce risk of damage to electric plug and cord, pull by plug when disconnecting

battery charger.

7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

8. An extension cord should not be used unless absolutely necessary. Use of improper

extension cord could result in a risk of fire and electric shock.

If extension cord must be used make sure:

a. That blades of extension cord are the same number, size, and shape as those of

plug on battery charger:

b. That extension cord is properly wired and in good electrical condition; and

c. That wire size is large enough for AC ampere rating of battery charger as specified

in Table 1.

* If the input rating of a battery charger is given in watts rather than in amperes, the

corresponding ampere rating is to be determined by dividing the wattage rating by the

voltage rating–for example:

Table 1

RECOMMENDED MINIMUM AWG SIZE FOR

EXTENSION CORDS FOR BATTERY CHARGERS

AC Input Rating Amperes* AWG Size of Cord

Equal to or but less Length of Cord, Feet (Meter)

greater than than 25 (7.5) 50 (15) 100 (30) 150 (45)

0 2 18 18 18 16

2 3 18 18 16 14

3 4 18 18 16 14

1250watts

125 volts

= 10 amperes

9

English

9. Do not operate battery charger with damaged cord or plug-replace them immediately.

10. Do not operate battery charger if it has received a sharp blow, been dropped, or otherwise

damaged in any way; take it to a qualified serviceman.

11. Do not disassemble battery charger; take it to a qualified serviceman when service or

repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

12. To reduce risk of electric shock, unplug charger from receptacle before attempting any

maintenance or cleaning. Removing the battery will not reduce this risk.

13. This battery charger might be attached to HITACHI battery operated tools as a standard

accessory. In this case, please confirm instruction Manual of the HITACHI battery

operated tools before using the battery charger.

IMPORTANT SAFETY INSTRUCTIONS FOR USE OF THE

BATTERY AND BATTERY CHARGER

You must charge the battery before you can use the power tool. Before using the model

UC 24YFA battery charger, be sure to read all instructions and cautionary statements on it,

the battery and in this manual.

REMEMBER: USE ONLY HITACHI BATTERY TYPE EB1820. OTHER TYPES OF BATTERIES

MAY BURST AND CAUSE INJURY!

Follow these instructions to avoid the risk of injury:

WARNING:Improper use of the battery or battery charger can lead to serious injury.

To avoid these injuries:

1. NEVER disassemble the battery.

2. NEVER incinerate the battery, even if it is damaged or is completely worn out. The

battery can explode in a fire.

3. NEVER short-circuit the battery.

4. NEVER insert any objects into the battery charger’s air vents. Electric shock or

damage to the battery charger may result.

5. NEVER charge outdoors. Keep the battery away from direct sunlight and use only

where there is low humidity and good ventilation.

6. NEVER charge when the temperature is below 32°F (0°C) or above 104°F (40°C).

7. NEVER connect two battery chargers together.

8. NEVER insert foreign objects into the hole for the battery or the battery charger.

9. NEVER use a booster transformer when charging.

10. NEVER use an engine generator or DC power to charge.

11. NEVER store the battery or battery charger in places where the temperature may

reach or exceed 104°F (40°C).

12. ALWAYS operate charger on standard household electrical power (120 volts). Using

the charger on any other voltage may overheat and damage the charger.

13. ALWAYS wait at least 15 minutes between charges to avoid overheating the charger.

14. ALWAYS disconnect the power cord from its receptacle when the charger is not in

use.

10

English

SAVE THESE INSTRUCTIONS

AND

MAKE THEM AVAILABLE TO

OTHER USERS

AND

OWNERS OF THIS TOOL!

11

English

FUNCTIONAL DESCRIPTION

NOTE:

The information contained in this Instruction Manual is designed to assist you in the

safe operation and maintenance of the power tool.

NEVER operate, or attempt any maintenance on the tool unless you have first read and

understood all safety instructions contained in this manual.

Some illustrations in this Instruction Manual may show details or attachments that differ

from those on your own power tool.

MODEL

CR18DV: with charger (UC24YFA) and case

NAME OF PARTS

1. Cordless Reciprocating Saw (CR18DV)

䡬 Battery (EB1820)

Fig. 1

Nameplate

Terminal Hole

Latch

Front Cover

Switch Trigger

Handle

Brush Cap

Holder Sleeve

Lock-Off Button

Battery

Blade

Base

12

English

SPECIFICATIONS

1. Cordless Reciprocating Saw (CR18DV)

2. Battery Charger (UC 24YFA)

Fig. 2

2. Battery Charger (UC 24YFA)

Motor DC motor

No-Load Speed 0 – 2100/min.

Stroke 1-1/8" (28 mm)

Capacity Mild Steel Pipe: O.D. 3-1/2" (90 mm)

Vinyl Chloride Pipe: O.D. 3-1/2" (90 mm)

Wood: Depth 3-1/2" (90 mm)

Battery (EB1820) Nickel cadmium battery

Voltage .................... DC 18V

Weight 8.6 lbs (3.9 kg)

Input power source Single phase: AC120V 60Hz

Charging time Approx. 50min. (At a temperature of 68°F (20°C))

Charger

Charging voltage ......................................... DC 7.2–24V

Charging current.......................................... DC 2.5A

Weight 1.3 lbs (0.6 kg)

Caution Plate

Battery Installation Hole

Pilot Lamp

Nameplate

13

English

Fig. 3

Latch

Push

Switch Trigger

Handle

Battery

Pull out

Insert

ASSEMBLY AND OPERATION

APPLICATIONS

䡬 Cutting metal and stainless steel pipe.

䡬 Cutting various lumber.

䡬 Cutting mild steel, aluminum and copper plate.

䡬 Cutting synthetic resins, such as phenol resin and vinyl chloride.

REMOVAL AND INSTALLATION METHOD OF BATTERY

CAUTION:Be sure to keep the switch turned off and the lock-off button moved to

right position (lock position). (See Fig. 19)

䡬 How to install the battery.

Align the battery with the groove in tool

handle and slip it into place.

Always insert it all the way until it locks in

place with a little click, If not, it may acci-

dentally fall out of the tool, causing injury

to you or someone around you. (Fig. 3)

䡬 How to remove the battery.

Withdraw battery from the tool handle while

pressing the latches on the sides of the

battery. (Fig. 3)

CHARGING METHOD

NOTE: Before plugging into the receptacle, make sure the following points.

䡬 The power source voltage is stated on the nameplate.

䡬 The cord is not damaged.

WARNING:Do not charge at voltage higher than indicated on the nameplate.

If charged at voltage higher than indicated on the nameplate, the

charger will burn out.

14

English

1. Insert the plug of battery charger into the receptacle.

When the plug of battery charger has been inserted into the receptacle, pilot lamp will

blink in red. (At 1-second intervals)

WARNING:

Do not use the electrical cord if damaged. Have it repaired

immediately.

2. Insert the battery to the battery charger.

Insert the battery into the battery charger as

shown in Fig. 4. Make sure it contacts the bottom

of the battery charger.

Fig. 4

3. Charging

䡬 When the battery is connected to the battery charger, charging will commence and the

pilot lamp will light in red. (See Table 2)

NOTE: If the pilot lamp flikers in red, pull out the plug from the receptacle and check if

the battery is properly mounted.

䡬 When the battery is fully charged, the pilot lamp will bilink in red slowly. (At 1-second

intervals) (See Table 2)

Battery

Pilot Lamp

15

English

Table 3

Rechargeable batteries

EB1820

Temperatures at which the battery can be recharged

23°F — 140°F

(–5°C — 60°C)

Table 2

Indications of the pilot lamp

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights continuously

Lights for 0.5 seconds. Does not light for

0.5 seconds. (off for 0.5 seconds)

Lights for 0.1 seconds. Does not light for

0.1 seconds. (off for 0.1 seconds)

Lights continuously

Before

charging

While

charging

Charging

complete

Charging

impossible

Charging

impossible

Malfunction in the battery or the

charger

The battery temperature is high,

making recharging impossible.

Blinks

(RED)

Lights

(RED)

Blinks

(RED)

Flickers

(RED)

Lights

(GREEN)

Battery Voltage (V)

Battery capacity (Ah)

2.0 Ah

18V EB1820 50min.

䡬 Regarding the temperature of the rechargeable battery.

The temperatures for rechargeable batteries are as shown in the table below, and

batteries that have become hot should be cooled for a while before being recharged.

䡬 Regarding recharging time

Table 4 shows the recharging time required according to the type of battery.

Table 4 Recharging time (approx. min.) at 68°F(20°C)

NOTE: The recharging time may vary according to ambient temperature and power

source voltage.

4. Disconnect battery charger from the receptacle.

CAUTION:

Do not pull the plug out of the receptacle by pulling on the cord.

Make sure to grasp the plug when removing from receptacle to avoid damaging cord.

16

English

5. Remove the battery from the battery charger.

Supporting the battery charger by hand, pull out the battery from the battery charger.

Regarding electric discharge in case of new batteries, etc.

As the internal chemical substance of new batteries and batteries that have not been

used for an extended period is not activated, the electric discharge might be low when

using them the first and second time. This is a temporary phenomenon, and normal

time required for recharging will be restored by recharging the batteries 2 – 3 times.

How to make the batteries perform longer.

䡬 Recharge the batteries before they become completely exhausted.

When you feel that the power of the tool becomes weaker, stop using the tool and

recharge its battery. If you continue to use the tool and exhaust the electric current, the

battery may be damaged and its life will become shorter.

䡬 Avoid recharging at high temperatures.

A rechargeable battery will be hot immediately after use. If such a battery is recharged

immediately after use, its internal chemical substance will deteriorate, and the battery

life will be shortened. Leave the battery and recharge it after it has cooled for a while.

CAUTION:

● When the battery charger has been continuosly used, the battery charger will heated,

thus constituting the cause of the failures. Once the charging has been completed,

give 15 minutes rest until the next charging.

● If the battery is rechraged when it is warm due to battery use or exposure to sunlight,

the pilot lamp may light in green.

The battery will not be recharged. In such a case, let the battery cool before charging.

● When the pilot lamp flickers in red (at 0.2–second intervals), check for and take out

any foreign objects in the charger’s battery installation hole. If there are no foreign

objects, it is probable that the battery or charger is malfunctioning. Take it to your

authorized Service Center.

BEFORE USE

Check the work area to make sure that it is clear of debris and clutter.

Clear the area of unnecessary personnel. Ensure that lighting and ventilation is adequate.

17

English

Holder

sleeve

Front

cover

Fig. 5

Holder

sleeve

Fig. 6

Blade

Plunger slit

Fig. 7

Blade

Plunger slit

Fig. 8

PRIOR TO OPERATION

1. Mounting the blade

This unit employs a detachable mechanism that

enables mounting and removal of saw blades

without the use of a wrench or other tools.

(1) Turn on and off the switching trigger several

times so that the holder sleeve can jump out of

the front cover completely. Thereafter, turn off

the switch and remove the battery. (Fig. 5)

CAUTION:Be absolutely sure to keep the switch

turned off and the battery removed

to prevent any accident.

(2) Turn the holder sleeve in the direction of the

arrow mark shown in Fig. 6 marked on the holder

sleeve. If you turn the holder sleeve halfway you

will be able to secure it automatically. (Fig. 6)

(3) Insert the saw blade all the way into the small

slit of the plunger tip. You can mount this blade

either in the upward or downward direction. (Fig.

7, Fig. 8)

(4) Pull the holder sleeve back slightly in the

direction of the arrow mark shown in Fig. 9 (in

the direction opposite to the arrow marked on

the holder sleeve). When you do this, the spring

force will return the holder sleeve to the correct

position automatically. There is no need to

fasten the holder sleeve at this time. (Fig. 9)

(5) Pull the back of the saw blade two or three times

by hand and check that the blade is securely

mounted. When pulling the blade, you will know

it is properly mounted if it clicks and the holder

sleeve moves slightly. (Fig. 10)

CAUTION:When pulling the saw blade, be

absolutely sure to pull it from the

back. Pulling other parts of the blade

will result in an injury.

2. Dismounting the blade

(1) Turn on and off the switching trigger several

times so that the holder sleeve can jump out of

the front cover completely. Thereafter, turn off

the switch and remove the battery. (Fig. 5)

18

English

CAUTION:Be absolutely sure to keep the switch

turned off and the battery removed

to prevent any accident.

(2) After you have turned the holder sleeve in the

direction of the arrow mark shown in Fig. 6 and

secured it, turn the blade so it faces downward.

The blade should fall out by itself. If the blade

does't fall out, pull it out by hand.

CAUTION:Never touch the saw blade

immediately after use. The metal is

hot and can easily burn your skin.

WHEN THE BLADE IS BROKEN

Even when the saw blade is broken and remains

inside the small slit of the plunger, it should fall out

if you turn the holder sleeve in the direction of the

arrow mark, secure the holder sleeve, and face the

blade downward. If it doesn’t fall out itself, take it

out using the procedures explained below.

(1) If a part of the broken saw blade is sticking out

of the small slit of the plunger, pull out the

protruding part and take the blade out.

(2) If the broken saw blade is hidden inside the small

slit, hook the broken blade using a tip of another

saw blade and take it out. (Fig. 11)

MAINTENANCE AND INSPECTION OF SAW BLADE

MOUNT

(1) After use, blow away sawdust, earth, sand,

moisture, etc., with air or brush them away with

a brush, etc., to ensure that the blade mount

can function smoothly.

(2)

Periodically lubricate the saw blade mount with

machine oil through the semicircular slit at a state

where the holder sleeve is turned in the direction

of the arrow mark shown in Fig. 6. (Fig. 12)

NOTE:

If the saw blade mount is used without proper

cleaning and lubrication, the rotation of the

holder sleeve may be hampered by sawdust and

particles of dust, disabling you to remove the

saw blade with your fingers.

In such a case, hold the periphery of the holder sleeve lightly using a pair of pliers

and the like, and turn the holder sleeve to left and right little by little. After the saw

blade has been successfully removed, be absolutely sure to clean it up with air,

etc., carry out proper lubrication, and then check and see if the saw blade mount

can function smoothly.

Holder

sleeve

Fig. 9

Holder

sleeve

Blade

Fig. 10

Another blade

Fig. 11

Holder

sleeve

Semicircular slit

Machine

oil

Fig. 12

19

English

Set screw

12 mm

Hexagonal

bar wrench

Base

Fig. 13

Stroke

Fig. 14

Fig. 15

Stroke

Fig. 16

Fig. 17

3. Moving the base

Loosen the set screw and move the base forward,

as shown in Fig. 13. Tighten the set screw slightly,

ensure the base does not move back and forth, and

firmly tighten the set screw. Ensure that the base

does not contact the blade.

4. Confirm that the battery is mounted correctly.

HOW TO USE THE CORDLESS RECIPROCATING SAW

CAUTION:

䡬 Avoid carrying it with your finger on the switch. A

sudden startup can result in an unexpected injury.

䡬 Be careful not to let sawdust, earth, moisture, etc.,

enter the inside of the machine through the plunger

section during operation. If sawdust and the like

accumulate in the plunger section, always clean it

before use.

䡬 Do not remove the front cover (refer to Fig. 5).

Be sure to hold the body from the top of the front

cover.

䡬 During use, press the base against the material

while cutting.

Vibration can damage the saw blade if the base is

not pressed firmly against the workpiece.

Furthermore, a tip of the saw blade can sometimes

contact the inner wall of the pipe, damaging the

saw blade.

䡬 Select a saw blade of the most appropriate length.

Ideally, the length protruding from the base of the

saw blade after subtracting the stroke should be

larger than the material (see Fig. 14 and Fig. 16).

If you cut a large pipe, large block of wood, etc.,

that exceeds the cutting capacity of a blade; there

is a risk that the blade may contact with the inner

wall of the pipe, wood, etc., resulting in damage.

(Fig. 15, Fig. 17)

1. Switch operation

(1) Lock-off button

The tool is equipped with a lock-off button. To

acivate the trigger lock, move the button to the right

positon. Move the button to the left to operate the

tool. (Fig. 18, Fig. 19)

20

English

CAUTION:Always lock the switch when

carrying or storing the tool eliminate

unintentional starting.

(2) Trigger switch

This tool is equipped with a variable speed

controlled trigger switch. The tool can be turned

"ON" or "OFF" by squeezing or releasing the trigger.

The blade plunger stroke rate can be adjusted from

the minimum to maximum nameplate stroke rate

by the pressure you apply to the trigger. Apply more

pressure to increase the speed and release pressure

to decrease speed.

2. Cutting metallic materials

CAUTION:

䡬 Press the base firmly against the workpiece.

䡬 Never apply any unreasonable force to the saw

blade when cutting. Doing so can easily break

the blade.

䡬 The motor can be locked sometimes, depending

on the combination of the material to be cut

and the blade. Whenever the motor gets locked,

switch it off immediately.

(1) Fasten a workpiece firmly before operation.

(Fig. 20)

(2) When cutting metallic materials, use proper

machine oil (turbine oil, etc.). When not using

liquid machine oil, apply grease over the

workpiece.

CAUTION:The service life of the saw blade will

be drastically shortened if you don’t

use machine oil.

3. Cutting lumber

When cutting lumber, make sure that the workpiece

is fastened firmly before beginning. (Fig. 21)

CAUTION:Never apply any unreasonable force

to the saw blade when cutting. Also

remember to press the base against

the lumber firmly.

4. Sawing curved lines

We recommend that you use the BIMETAL

blade mentioned in Page 26 for the saw blade

since it is tough and hardly breaks.

Fig. 18

Fig. 19

Lock-off

button

Lock

Lock-off

button

Free

Fig. 20

Fig. 21

Fig. 22

La page charge ...

Hitachi CR 18DV Manuel utilisateur

Ce manuel convient également à

Hitachi CR 18DV Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents