DeWalt D28499 Manuel utilisateur

D28499, DWE4557, DWE4557G, DWE4559CN, DWE4559NG, DWE4559CNG, DWE4559N,

DWE4597, DWE4597N, DWE4599N

Heavy Duty Large Angle Grinders

Grandes rectifieuses coudées de service intensif

Esmeriladoras de ángulo grande para trabajo pesado

INSTRUCTION MANUAL

GUIDE D’UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to these

symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY D

EWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT

(1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction

manual.

General Power Tool Safety Warnings

WARNING! Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in

electric shock, fire and/or serious injury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

The term “power tool” in the warnings refers to your mains-operated

(corded) power tool or battery-operated (cordless) power tool.

1) WORK AREA SAFETY

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Do not operate power tools in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Power tools create sparks which may ignite the dust or

fumes.

c) Keep children and bystanders away while operating a

power tool. Distractions can cause you to lose control.

2) ELECTRICAL SAFETY

a) Power tool plugs must match the outlet. Never modify

the plug in any way. Do not use any adapter plugs with

earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce risk of electric shock.

b) Avoid body contact with earthed or grounded surfaces

such as pipes, radiators, ranges and refrigerators. There

is an increased risk of electric shock if your body is earthed or

grounded.

c) Do not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric

shock.

d

)

Do not abuse the cord. Never use the cord for carrying,

pulling or unplugging the power tool. Keep cord away

from heat, oil, sharp edges or moving parts. Damaged or

entangled cords increase the risk of electric shock.

e) When operating a power tool outdoors, use an extension

cord suitable for outdoor use. Use of a cord suitable for

outdoor use reduces the risk of electric shock.

f

)

If operating a power tool in a damp location is unavoidable,

use a ground fault circuit interrupter (GFCI) protected

supply. Use of a GFCI reduces the risk of electric shock.

English

1

3) PERSONAL SAFETY

a) Stay alert, watch what you are doing and use common

sense when operating a power tool. Do not use a power

tool while you are tired or under the influence of drugs,

alcohol or medication. A moment of inattention while

operating power tools may result in serious personal injury.

b) Use personal protective equipment. Always wear eye

protection. Protective equipment such as dust mask, non-

skid safety shoes, hard hat, or hearing protection used for

appropriate conditions will reduce personal injuries.

c) Prevent unintentional starting. Ensure the switch is in

the off position before connecting to power source and/

or battery pack, picking up or carrying the tool. Carrying

power tools with your finger on the switch or energizing power

tools that have the switch on invites accidents.

d

)

Remove any adjusting key or wrench before turning the

power tool on. A wrench or a key left attached to a rotating

part of the power tool may result in personal injury.

e) Do not overreach. Keep proper footing and balance at

all times. This enables better control of the power tool in

unexpected situations.

f

)

Dress properly. Do not wear loose clothing or jewelry.

Keep your hair, clothing and gloves away from moving

parts. Loose clothes, jewelry or long hair can be caught in

moving parts.

g) If devices are provided for the connection of dust

extraction and collection facilities, ensure these are

connected and properly used. Use of dust collection can

reduce dust-related hazards.

4) POWER TOOL USE AND CARE

a) Do not force the power tool. Use the correct power tool

for your application. The correct power tool will do the job

better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with the

switch is dangerous and must be repaired.

c) Disconnect the plug from the power source and/or the

battery pack from the power tool before making any

adjustments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d

)

Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power tools

are dangerous in the hands of untrained users.

e) Maintain power tools. Check for misalignment or binding

of moving parts, breakage of parts and any other

condition that may affect the power tool’s operation. If

damaged, have the power tool repaired before use. Many

accidents are caused by poorly maintained power tools.

f

)

Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to bind and

are easier to control.

g) Use the power tool, accessories and tool bits, etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the power tool for operations different from those

intended could result in a hazardous situation.

English

2

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR

ALL OPERATIONS

Safety Warnings Common for Grinding,

Sanding, Wire Brushing, Polishing or

Abrasive, Cutting-Off Operations

a) This power tool is intended to function as a grinder,

sander, wire brush, polisher or cut-off tool. Read all safety

warnings, instructions, illustrations and specifications

provided with this power tool. Failure to follow all instructions

listed below may result in electric shock, fire and/or serious

injury.

b) Do not use accessories which are not specifically

designed and recommended by the tool manufacturer.

Just because the accessory can be attached to your power

tool, it does not assure safe operation.

c) The rated speed of the accessory must be at least

equal to the maximum speed marked on the power tool.

Accessories running faster than their rated speed can break

and fly apart.

d

)

The outside diameter and the thickness of your accessory

must be within the capacity rating of your power tool.

Incorrectly sized accessories cannot be adequately guarded or

controlled.

e) The arbor size of wheels, flanges, backing pads or

any other accessory must properly fit the spindle of

the power tool. Accessories with arbor holes that do not

match the mounting hardware of the power tool will run out of

balance, vibrate excessively and may cause loss of control.

f

)

Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for chips

and cracks, backing pad for cracks, tear or excess wear,

wire brush for loose or cracked wires. If power tool or

accessory is dropped, inspect for damage or install an

undamaged accessory. After inspecting and installing an

accessory, position yourself and bystanders away from

the plane of the rotating accessory and run the power

tool at maximum no-load speed for one minute. Damaged

accessories will normally break apart during this test time.

g) Wear personal protective equipment. Depending on

application, use face shield, safety goggles or safety

glasses. As appropriate, wear dust mask, hearing

protectors, gloves and workshop apron capable of

stopping small abrasive or workpiece fragments. The eye

protection must be capable of stopping flying debris generated

by various operations. The dust mask or respirator must be

capable of filtrating particles generated by your operation.

Prolonged exposure to high intensity noise may cause hearing

loss.

h) Keep bystanders a safe distance away from work area.

Anyone entering the work area must wear personal

protective equipment. Fragments of workpiece or of a

broken accessory may fly away and cause injury beyond

immediate area of operation.

i) Hold power tool by insulated gripping surfaces only,

when performing an operation where the cutting

accessory may contact hidden wiring or its own cord.

Cutting accessory contacting a “live” wire may make exposed

metal parts of the power tool “live” and could give the operator

an electric shock.

English

3

j) Position the cord clear of the spinning accessory. If you

lose control, the cord may be cut or snagged and your hand or

arm may be pulled into the spinning accessory.

k) Never lay the power tool down until the accessory has

come to a complete stop. The spinning accessory may grab

the surface and pull the power tool out of your control.

l) Do not run the power tool while carrying it at your side.

Accidental contact with the spinning accessory could snag

your clothing, pulling the accessory into your body.

m) Regularly clean the power tool’s air vents. The motor’s

fan will draw the dust inside the housing and excessive

accumulation of powdered metal may cause electrical hazards.

n) Do not operate the power tool near flammable materials.

Sparks could ignite these materials.

o) Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in electrocution

or shock.

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating

wheel, backing pad, brush or any other accessory. Pinching or

snagging causes rapid stalling of the rotating accessory which

in turn causes the uncontrolled power tool to be forced in the

direction opposite of the accessory’s rotation at the point of the

binding.

For example, if an abrasive wheel is snagged or pinched by the

workpiece, the edge of the wheel that is entering into the pinch

point can dig into the surface of the material causing the wheel

to climb out or kick out. The wheel may either jump toward or

away from the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels may also

break under these conditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by taking

proper precautions as given below:

a) Maintain a firm grip on the power tool and position your

body and arm to allow you to resist kickback forces.

Always use auxiliary handle, if provided, for maximum

control over kickback or torque reaction during start up.

The operator can control torque reaction or kickback forces, if

proper precautions are taken.

b) Never place your hand near the rotating accessory.

Accessory may kickback over your hand.

c) Do not position your body in the area where power tool

will move if kickback occurs. Kickback will propel the tool

in direction opposite to the wheel’s movement at the point of

snagging.

d

)

Use special care when working corners, sharp edges etc.

Avoid bouncing and snagging the accessory. Corners,

sharp edges or bouncing have a tendency to snag the rotating

accessory and cause loss of control or kickback.

e) Do not attach a saw chain woodcarving blade or toothed

saw blade. Such blades create frequent kickback and loss of

control.

Safety Warnings Speciﬁ c for Grinding and

Abrasive Cutting-Off Operations

a) Use only wheel types that are recommended for your

power tool and the specific guard designed for the

selected wheel. Wheels for which the power tool was not

designed cannot be adequately guarded and are unsafe.

b) The guard must be securely attached to the power tool

and positioned for maximum safety, so the least amount

of wheel is exposed towards the operator. The guard helps

English

4

to protect operator from broken wheel fragments, accidental

contact with wheel , and sparks that could ignite clothing.

c) Wheels must be used only for recommended applications.

For example: do not grind with the side of cut-off wheel.

Abrasive cut-off wheels are intended for peripheral grinding,

side forces applied to these wheels may cause them to shatter.

d

)

Always use undamaged wheel flanges that are of correct

size and shape for your selected wheel. Proper wheel

flanges support the wheel thus reducing the possibility of wheel

breakage. Flanges for cut-off wheels may be different from

grinding wheel flanges.

e) Do not use worn down wheels from larger power tools.

Wheel intended for larger power tool is not suitable for the

higher speed of a smaller tool and may burst.

Additional Safety Warnings Speciﬁ c for

Abrasive Cutting-Off Operations

a) Do not “jam” the cut-off wheel or apply excessive

pressure. Do not attempt to make an excessive depth

of cut. Overstressing the wheel increases the loading and

susceptibility to twisting or binding of the wheel in the cut and

the possibility of kickback or wheel breakage.

b) Do not position your body in line with and behind the

rotating wheel. When the wheel, at the point of operation, is

moving away from your body, the possible kickback may propel

the spinning wheel and the power tool directly at you.

c) When wheel is binding or when interrupting a cut for any

reason, switch off the power tool and hold the power

tool motionless until the wheel comes to a complete

stop. Never attempt to remove the cut-off wheel from

the cut while the wheel is in motion otherwise kickback

may occur. Investigate and take corrective action to eliminate

the cause of wheel binding.

d

)

Do not restart the cutting operation in the workpiece.

Let the wheel reach full speed and carefully reenter the

cut. The wheel may bind, walk up or kickback if the power tool

is restarted in the workpiece.

e) Support panels or any oversized workpiece to minimize

the risk of wheel pinching and kickback. Large workpieces

tend to sag under their own weight. Supports must be placed

under the workpiece near the line of cut and near the edge of

the workpiece on both sides of the wheel.

f

)

Use extra caution when making a “pocket cut” into

existing walls or other blind areas. The protruding wheel

may cut gas or water pipes, electrical wiring or objects that can

cause kickback.

Safety Warnings Speciﬁ c for Sanding

Operations

a) Do not use excessively oversized sanding disc paper.

Follow manufacturer's recommendations when selecting

sanding paper. Larger sanding paper extending beyond the

sanding pad presents a laceration hazard and may cause

snagging, tearing of the disc or kickback.

Safety Warnings Speciﬁ c for Polishing

Operations

a) Do not allow any loose portion of the polishing bonnet

or its attachment strings to spin freely. Tuck away or

trim any loose attachment strings. Loose and spinning

attachment strings can entangle your fingers or snag on the

workpiece.

English

5

Safety Warnings Speciﬁ c for Wire

Brushing Operations

a) Be aware that wire bristles are thrown by the brush even

during ordinary operation. Do not overstress the wires

by applying excessive load to the brush. The wire bristles

can easily penetrate light clothing and/or skin.

b) If the use of a guard is recommended for wire brushing,

do not allow any interference of the wire wheel or brush

with the guard. Wire wheel or brush may expand in diameter

due to work load and centrifugal forces.

Additional Safety Rules for Grinders

WARNING: The grinding wheel or accessory may loosen

during coast-down of the tool when shut off. If grinding wheel

or accessory loosens, it may dismount from the machine and may

cause serious personal injury.

• Use of accessories not specified in this manual is not

recommended and may be hazardous. Use of power boosters

that would cause the tool to be driven at speeds greater than its

rated speed constitutes misuse.

• Use clamps or another practical way to secure and support

the workpiece to a stable platform. Holding the work by hand

or against your body leaves it unstable and may lead to loss of

control.

• Avoid bouncing the wheel or giving it rough treatment. If this

occurs, stop the tool and inspect the wheel for cracks or flaws.

• Always handle and store wheels in a careful manner.

• Never cut into area that may contain electrical wiring or

piping. Serious injury may result.

• Do not operate this tool for long periods of time. Vibration

caused by the operating action of this tool may cause permanent

injury to fingers, hands, and arms. Use gloves to provide extra

cushion, take frequent rest periods, and limit daily time of use.

• Direct the Dust Ejection System (DES) away from operator

and coworkers. Serious injury may result.

• When the gear case grip is properly installed, the use of the side

handle is not required.

• When not in use, place grinder on a stable surface where it

will not move inadvertantly, roll or cause a tripping or falling

hazard. Serious personal injury may result.

• Air vents often cover moving parts and should be avoided.

Loose clothes, jewelry or long hair can be caught in moving parts.

• An extension cord must have adequate wire size (AWG

or American Wire Gauge) for safety. The smaller the gauge

number of the wire, the greater the capacity of the cable, that is

16 gauge has more capacity than 18 gauge. An undersized cord

will cause a drop in line voltage resulting in loss of power and

overheating. When using more than one extension to make up the

total length, be sure each individual extension contains at least the

minimum wire size. The following table shows the correct size to

use depending on cord length and nameplate ampere rating. If in

doubt, use the next heavier gauge. The smaller the gauge number,

the heavier the cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts

Total Length of Cord

in Feet (meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

More

Than

Not More

Than

AWG

0 6 18 16 16 14

610 18161412

10 12 16 16 14 12

12 16 14 12 Not Recommended

English

6

WARNING: ALWAYS use safety glasses. Everyday eyeglasses are

NOT safety glasses. Also use face or dust mask if cutting operation is

dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratory protection.

WARNING: Some dust created by power sanding, sawing,

grinding, drilling, and other construction activities contains chemicals

known to the State of California to cause cancer, birth defects or other

reproductive harm. Some examples of these chemicals are:

• lead from lead-based paints,

• crystalline silica from bricks and cement and other masonry

products, and

• arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you

do this type of work. To reduce your exposure to these chemicals:

work in a well ventilated area, and work with approved safety

equipment, such as those dust masks that are specially designed to

filter out microscopic particles.

• Avoid prolonged contact with dust from power sanding,

sawing, grinding, drilling, and other construction

activities. Wear protective clothing and wash exposed

areas with soap and water. Allowing dust to get into your

mouth, eyes, or lay on the skin may promote absorption of

harmful chemicals.

WARNING: Use of this tool can generate and/or disperse dust,

which may cause serious and permanent respiratory or other

injury. Always use NIOSH/OSHA approved respiratory protection

appropriate for the dust exposure. Direct particles away from face

and body.

WARNING: Always wear proper personal hearing protection

that conforms to ANSI S12.6 (S3.19) during use. Under some

conditions and duration of use, noise from this product may

contribute to hearing loss.

• The label on your tool may include the following symbols. The

symbols and their definitions are as follows:

V ............volts

Hz ..........hertz

min ........minutes

.....direct current

.......... Class I Construction

(grounded)

.......... Class II Construction

(double insulated)

…/min ...per minute

IPM ...........impacts per minute

SPM .........strokes per minute

sfpm ......... surface feet per

minute

A ............amperes

W ..............watts

............alternating current

............ alternating or direct

current

n

o .............no load speed

n ...............rated speed

.............earthing terminal

..............safety alert symbol

BPM .........beats per minute

RPM ......... revolutions per

minute

SAVE THESE INSTRUCTIONS FOR

FUTUREUSE

Motor

Be sure your power supply agrees with the nameplate marking.

Voltage decrease of more than 10% will cause loss of power and

overheating. D

EWALT tools are factory tested; if this tool does not

operate, check power supply.

English

7

FAMILIARIZATION

Large angle grinders are designed for heavy material removal in extended

use applications. The following grinders are described in this manual:

D28499 9" Angle Grinder 6,000 rpm

DWE4557G 7" Angle Grinder 8,500 rpm

DWE4559NG 9" Angle Grinder 6,500 rpm

DWE4559CNG 9" Angle Grinder 6,500 rpm

DWE4597 7" Angle Grinder 8,500 rpm

DWE4597N 7" Angle Grinder 8,500 rpm

DWE4599N 9" Angle Grinder 6,500 rpm

FIG. 1

D

J

F

H

I

K

A

B

C

COMPONENTS (Fig. 1, 9, 18)

WARNING: Never modify the power tool or any part of it. Damage

or personal injury could result.

A. Trigger switch

B. Lock-off button

C. Lock-on button

D. Spindle lock button

E. Spindle (Fig. 9)

F. Guard

G. Soft mount (Fig. 18)

H. Side handle

I. LED indicator

J. Anti-vibration ring

K. Dust ejection port

INTENDED USE

This grinder is designed for professional grinding, sanding, wire

brushing, polishing or abrasive, cutting-off applications.

DO NOT use under wet conditions or in presence of flammable

liquids or gases.

This grinder is a professional power tool. DO NOT let children come

into contact with the tool. Supervision is required when inexperienced

operators use this tool.

ANTI-VIBRATION REAR HANDLE (FIG. 1)

The anti-vibration ring (J) reduces handle vibration and user fatigue in

extended use applications.

DUST EJECTION SYSTEM

The dust ejection system deflects debris that would be harmful to the

motor and allows cleaner air to pass over the motor.

TOUGHCORD™ SYSTEM

The TOUGHCORD™ system reduces the likelihood of cord pullout.

KEYLESS GUARD

This allows for tool-free guard change and adjustment.

English

8

E-SWITCH PROTECTION™

(DWE4597, DWE4597N, DWE4599N)

The ON/OFF trigger switch has a no-volt release function. In the event

of a power outage or other unexpected shut down, the trigger switch

will need to be cycled (turned on and off) to restart tool.

CLUTCH

(DWE4597, DWE4597N, DWE4599N)

The torque limiting clutch reduces the maximum reaction torque

transmitted to the operator in the case of jamming a cutting disc. This

feature also prevents the gearing and electric motor from stalling. The

torque limiting clutch has been factory set and cannot be adjusted.

E-CLUTCH™

(DWE4597, DWE4597N, DWE4599N)

This unit is equipped with an E-Clutch™ (Electronic Clutch), which

in the event of a high-load or wheel pinch, the unit will be shut off to

reduce the reaction torque to the user. The switch needs to be cycled

(turned on and off) to restart tool.

POWER-OFF™ OVERLOAD PROTECTION

(DWE4597, DWE4597N, DWE4599N)

The power supply to the motor will be reduced in case of motor

overload. With continued motor overload, the tool will shut off. The

switch needs to be cycled (turned on and off) to restart tool. The tool

will power off each time the current load reaches the overload current

value (motor burn-up point). If continued overload shutdowns occur,

apply less force/weight on the tool until the tool will function without

the overload engaging.

COMPLETE ELECTRONIC CONTROL™

(DWE4597, DWE4597N, DWE4599N)

The internal electronic speed control offers consistent wheel speed

while using the tool.

ELECTRONIC SOFT START

(DWE4597, DWE4597N, DWE4599N)

This feature limits the initial start up momentum, allowing the speed to

build up gradually over a 1 second period.

ASSEMBLY AND ADJUSTMENTS

WARNING: To reduce the risk of injury, turn unit off

and disconnect it from power source before installing and

removing accessories, before adjusting or when making

repairs. An accidental start-up can cause injury.

Attaching Side Handle (Fig. 2)

The side handle (H) can be fitted to either side or the

FIG. 2

top of the gear case in the threaded holes. The

side positions are designed for optimized balance

in surface finishing and grinding applications. The

side handle must be used at all times to maintain

proper control of the tool. Before using the tool,

check that the handle is tightened se cure ly.

NOTE: The D28499 offers 5 handle locations for

additional versatility.

ANTI-VIBRATION SIDE HANDLE

(DWE4597, DWE4597N, DWE4599N)

The anti-vibration side handle reduces vibration and user fatigue in

extended use applications.

GEAR CASE GRIP (FIG. 3)

(DWE4559CN, DWE4559CNG)

The DWE4559CN and DWE4559CNG include a soft grip cover for

the gear case that can be used as a gripping surface only for pipeline

grinding and wire brushing where the edge of the wheel is used

for grinding and cleaning and precise control is needed to ensure

accuracy. As with any gripping surface, maintain firm grip during use.

English

9

The side handle should be used as the secondary grip surface for all

other applications.

FIG. 3

The gear case grip may be purchased at additional cost. Please

call 1-800-4-D

EWALT (1-800-433-9258) or visit our website:

www.dewalt.com.

Rotating the Gear Case (Fig. 4)

For applications in which a tool will be

FIG. 4

dedicated for uses in edge grinding and

finishing work, the gear case may be

rotated 90° left or right of its original

position.

1. Remove the four corner screws

attaching the gear case to motor

housing.

2. Without separating the gear case from motor housing, rotate the

gear case head to desired position.

NOTE: If the gear case and motor housing become separated

by more than 1/8" (3.17 mm), the tool must be serviced and

re-assembled by a D

EWALT service center. Failure to have the tool

serviced may cause brush, motor and bearing failure.

3. Reinstall screws to attach the gear case to the motor housing.

Tighten screws to 20 in.-lbs. torque. Overtightening could cause

screws to strip.

Rotating the Rear Handle (Fig. 5)

(D28499 ONLY)

1. Unlock the rear handle by

L

FIG. 5

pulling out the Handle Re lease

Lever (L).

2. Rotate handle into available

0°, 30°, 60°, or 90° position

left OR right of center.

3. Push in the handle release

lever.

4. Before turning the tool on, ensure that the handle is locked into a

position and the handle release lever has returned to the original

position flush with the tool housing.

Wheel Mounting Accessories and

Attachments

It is important to choose the correct guards, backing pads and

flanges to use with grinder accessories. Refer to pages 11–13 for

information on choosing the correct wheel mounting accessories.

ATTACHMENTS

Attachments designed specifically for this grinder can be

purchased through D

EWALT dealers and DEWALT Factory Service

centers.

9" Type 27 guard D284939

9" Type 28 guard D284938

7" Type 27 guard D284937

5"–6" Type 11 flaring cup guard with flange D284936

4" Type 11 flaring cup guard with flange D284934

English

10

Type 11 flaring cup wheel backing flange N197992

Type 1 flange set D284932

7" Type 1 guard D284931

Grinding backing flange 54339-00

Clamp nut 22191-00

Wheel wrench 61820-01

Soft mount spindle protector 445928-01

WARNING: Accessories must be rated for at least the speed

recom mended on the tool warning label. Wheels and other

accessories running over their rated accessory speed may fly apart

and cause injury. Threaded accessories must have a 5/8"–11 hub.

Every unthreaded accessory must have a 7/8" (22.2 mm) arbor

hole. If it does not, it may have been designed for a circular saw.

Use only the accessories shown on pages 11–13 of this manual.

Accessory ratings must always be above tool speed as shown on

tool nameplate.

Mounting Guard

MOUNTING AND REMOVING GUARD (FIG. 6, 7)

WARNING: Guards must be used with all grinding wheels,

cutting wheels, sanding flap discs, wire brushes, and wire

wheels. Guard modification that results in reduced coverage

of the accessory could result in severe personal injury. The tool

may be used without a guard only when sanding with conventional

sanding discs. A Type 27 guard (intended for use with depressed

center grinding wheels [Type 27 and Type 29], sanding flap discs, wire

wheels and wire cup brushes) is available at extra cost from your local

dealer or authorized service center. Grinding and cutting with wheels

other than Type 27 and 29 require different accessory guards not

included with tool. A Type 1 guard is provided for use with the Type 1

wheel. Mounting instructions for accessory guards are shown below

and are also included in the accessory package.

NOTE: Wheel size must match guard size; i.e., a new 7" wheel may

not be used with a 9" guard. The bottom surface of wheel must be

inside the bend of the guard lip.

soft mount

445928-01

Type 27 guard

D284937 7"

D284939 9"

backing flange

54339-00

non-hubbed sanding

flap disc

clamp nut

22191-00

Sanding Flap Discs

soft mount

445928-01

Type 27 guard

D284937 7"

D284939 9"

hubbed sanding

flap disc

English

11

NOTE: Wheel size must match guard size; i.e., a new 7" wheel may not be used with a 9"

guard. The bottom surface of wheel must be inside the bend of the guard lip.

Grinding Wheels

soft mount

445928-01

Type 27 guard

D284937 7"

D284939 9"

Type 27 hubbed wheel

soft mount

445928-01

Type 28 guard

D284938 9"

Type 28 hubbed wheel

Sanding Discs

soft mount

445928-01

rubber backing pad

sanding disc

clamp nut

soft mount

445928-01

Type 28 guard

D284938 9"

backing flange

54339-00

Type 28 non-hubbed

wheel

clamp nut

22191-00

soft mount

445928-01

Type 27 guard

D284937 7"

D284939 9"

backing flange

54339-00

Type 27 non-hubbed

wheel

clamp nut

22191-00

English

12

NOTE: Wheel size must match guard size; i.e., a 7" wheel

may not be used with a 9" guard.

soft mount

445928-01

Type 27 guard

D284937 7"

D284939 9"

wire cup brush

Type 11

flaring cup guard

D284934 4"

D284936 5"– 6"

backing flange

N197992

flaring cup stone

soft mount

445928-01

Type 27 guard

D284937 7"

D284939 9"

wire wheel

Type 1 guard

D284931

backing flange

N188469

abrasive cutting wheel

clamp nut

401678-06

Type 1 guard

D284931

backing flange

N188469

diamond cutting wheel

clamp nut

401678-06

Flaring Cup StonesWire Wheels Cutting Wheels

English

13

1. Open the guard latch (M), and align the

M

N

O

FIG. 6

F

lugs (N) on the guard with the slots on

the gear case (O). This will align the lugs

on the guard with the slots on the gear

case cover.

2. Push the guard down until the guard

lugs engage and can rotate freely into

the groove on the gear case hub.

3. With the guard latch open, rotate the

guard (F) into the desired working

position. The guard body should be

positioned between the spindle and the

operator to provide maximum operator

protection.

4. Close the guard latch to secure the

guard on the gear case. You should

not be able to rotate the guard by

hand when the latch is closed. Do not

operate the grinder with a loose guard or with the guard latch in

open position.

5. To remove the guard, follow the procedure above in reverse order.

NOTE: The guard is pre-adjusted to the

P

FIG. 7

diameter of the gear case hub at the factory.

If, after a period of time, the guard becomes

loose, tighten the adjusting screw (P) with

guard latch in the closed position with guard

installed on the tool.

CAUTION: Do not tighten the adjusting

screw with the guard latch in the open

position. Undetectable damage to the guard

or the mounting hub may result.

CAUTION: If the guard cannot be tightened by the adjusting

clamp, do not use the tool. To reduce the risk of personal injury, take

the tool and guard to a service center to repair or replace the guard.

NOTE: Edge grinding and cutting can be performed with

Type 27 wheels designed and specified for this purpose; 1/4"

(6.35 mm) thick wheels are designed for surface grinding while 1/8"

(3.17 mm) wheels are designed for edge grinding. Cutting can also be

performed by using a Type 1 wheel and a Type 1 guard.

OPERATION

WARNING: To reduce the risk of injury, turn unit off

and disconnect it from power source before installing and

removing accessories, before adjusting or when making

repairs. An accidental start-up can cause injury.

Switch (Fig. 8)

CAUTION: Before connecting the tool to a power source or after

a power failure, depress and release the trigger switch (A) once

without depressing the lock-on button (C) to ensure that the switch is

in the off position. If the trigger switch is locked on, the tool will start

unexpectedly when power is reconnected to the tool. Hold the side

handle and rear handle firmly to maintain control of tool at start up

and during use.

TRIGGER OPERATION

To turn the tool on, depress lock-off button (B)

A

B

C

FIG. 8

then trigger switch (A). The trigger can be

feathered as long as the lock-off button is

depressed. The tool will remain running while

the trigger is depressed. Turn the tool off by

releasing the trigger.

English

14

TRIGGER OPERATION WITH LOCK-ON FEATURE

To turn tool on, depress trigger. Depress and hold lock-on button (C)

while releasing trigger. Lock-on button will remain depressed and tool

will remain on.

To turn the tool off, depress and release trigger. The lock-on button

will pop out, permitting the trigger to disengage and causing the tool

to turn off.

NOTE: Allow the tool to reach full speed before touching tool to work

surface. Lift the tool from the work surface before turning the tool off.

CAUTION: Make sure the wheel has come to a complete stop

be fore setting the tool down.

SPINDLE LOCK BUTTON (FIG. 9)

The spindle lock button (D) is provided to

FIG. 9

D

prevent the spindle from rotating when

installing or removing wheels.

NOTICE: To reduce the risk of damage to

the tool, do not engage the spindle lock

button while the tool is operating. Damage

to the tool will result and attached accessory

may spin off possibly resulting in injury.

To engage the lock, depress the spindle lock button (D) and rotate the

spindle until you are unable to rotate the spindle further.

Mounting and Using Depressed Center

Grinding Wheels and Sanding Flap Discs

MOUNTING AND REMOVING HUBBED WHEELS

Hubbed wheels install directly on the 5/8"—11 threaded spindle.

1. Thread the wheel on the spindle by hand, seating the wheel

against the soft mount.

2. Depress the spindle lock button and use a wrench to tighten the

hub of the wheel.

3. Reverse the above procedure to remove the wheel.

CAUTION: Failure to properly seat the wheel against the soft

mount before turning the tool on may result in damage to the tool or

the wheel.

MOUNTING NON-HUBBED WHEELS

Depressed center, Type 27 grinding wheels

FIG. 10

Q

E

R

must be used with available accessory flanges.

See the chart on pages 11–13 of this manual

for more information.

1. Install the metal backing flange (Q) on

spindle (E) against the soft mount.

2. Place wheel against the backing flange,

centering the wheel on the backing flange

pilot.

3. While depressing the spindle lock button,

thread the clamp nut (R) on spindle,

piloting the raised hub on clamp nut in the

center of grinding wheel.

4. Tighten the clamp nut with a wrench.

5. Reverse the above procedure to remove the wheel.

SURFACE GRINDING WITH GRINDING WHEELS (FIG. 11)

1. Allow the tool to reach full speed before

FIG. 11

20˚–30˚

touching the tool to the work surface.

2. Apply minimum pressure to the work

surface, allowing the tool to operate at

high speed. Grinding rate is greatest

when the tool operates at high speed.

3. Maintain a 20° to 30° angle between the tool and work surface.

English

15

4. Continuously move the tool in a forward and back motion to avoid

creating gouges in the work surface.

5. Remove the tool from work surface before turning tool off. Allow

the wheel to stop rotating before laying the tool down.

EDGE GRINDING WITH GRINDING WHEELS

(FIG. 12)

WARNING: Wheels used for cutting and edge grinding may break

or kickback if they bend or twist while the tool is being used to do

cut-off work or deep grinding. To reduce the risk of serious injury, limit

the use of these wheels with a standard Type 27 guard to shallow

cutting and notching (less than 1/2" [13 mm] in depth). The open side

of the guard must be positioned away from the operator. For deeper

cutting with a Type 1 cut-off wheel, use a closed Type 1 guard. Refer

to pages 11–13 for more information.

1. Allow the tool to reach full speed before touching the tool to the

work surface.

2. Apply minimum pressure to the work surface,

FIG. 12

allowing the tool to operate at high speed.

Grinding rate is greatest when the tool

operates at high speed.

3. Position yourself so that the open-underside

of the wheel is facing away from you.

4. Once a cut is begun and a notch is

established in the workpiece, do not change

the angle of the cut. Changing the angle will

cause the wheel to bend and may cause

wheel breakage. Edge grinding wheels are

not designed to withstand side pressures

caused by bending.

5. Remove the tool from the work surface before turning the tool off.

Allow the wheel to stop rotating before laying the tool down.

WARNING: Do not use edge grinding/cutting wheels for surface

grinding applications because these wheels are not designed for side

pressures encountered with surface grinding. Wheel breakage and

serious personal injury may result.

SURFACE FINISHING WITH SANDING FLAP DISCS (FIG. 13)

1. Allow the tool to reach full speed before

5˚–10˚

FIG. 13

touching the tool to the work surface.

2. Apply minimum pressure to work

surface, allowing the tool to operate at

high speed. Sanding rate is greatest

when the tool operates at high speed.

3. Maintain a 5° to 10° angle between the

tool and work surface.

4. Continuously move the tool in a forward and back motion to avoid

creating gouges in the work surface.

5. Remove the tool from work surface before turning tool off. Allow

the wheel to stop rotating before laying the tool down.

MOUNTING SANDING BACKING PADS (FIG. 14)

NOTE: Guard may be removed when using sanding backing pads.

WARNING: Proper guard must be reinstalled

FIG. 14

S

T

R

for grinding wheel, cutting wheel, sanding flap

disc, wire brush or wire wheel applications after

sanding applications are complete.

1. Place or appropriately thread backing pad

(S) on the spindle.

2. Place the sanding disc (T) on the backing

pad (S).

3. While depressing the spindle lock button,

thread clamp nut (R) on spindle, piloting the

raised hub on the clamp nut into the center

of san ding disc and backing pad.

English

16

4. Tighten the clamp nut by hand. Then depress the spindle lock

button while turning the sanding disc until the sanding disc and

clamp nut are snug.

5. To remove the wheel, grasp and turn the backing pad and

sanding disc while depressing the spindle lock button.

USING SANDING BACKING PADS (FIG. 15)

Choose the proper grit sanding discs for your application. Sanding

discs are available in various grits. Coarse grits yield faster material

removal rates and a rougher finish. Finer grits yield slower material

removal and a smoother finish.

Begin with coarse grit discs for fast, rough material removal. Move to

a medium grit paper and finish with a fine grit disc for optimal finish.

Coarse 16–30 grit

Medium 36–80 grit

Fine Finishing 100–120 grit

Very Fine Finishing 150–180 grit

1. Allow the tool to reach full speed before touching tool to the work

surface.

2. Apply minimum pressure to work surface, allowing the tool to

operate at high speed. Sanding rate is greatest when the tool

operates at high speed.

3. Maintain a 5° to 15° angle between the tool and work surface.

The san ding disc should contact approximately 1" (25.4 mm) of

work surface.

4. Move the tool constantly in a straight line

5˚–15˚

FIG. 15

to prevent burning and swirling of work

surface. Allowing the tool to rest on the

work surface without moving, or moving

the tool in a circular motion causes

burning and swirling marks on the work

surface.

5. Remove the tool from work surface before turning tool off. Allow

the wheel to stop rotating before laying the tool down.

Precautions To Take When Sanding Paint

1. Sanding of lead based paint is NOT RECOMMENDED due to

the difficulty of controlling the contaminated dust. The greatest

danger of lead poisoning is to children and pregnant women.

2. Since it is difficult to identify whether or not a paint contains

lead without a chemical analysis, we recommend the following

precautions when sanding any paint:

PERSONAL SAFETY

1. No children or pregnant women should enter the work area

where the paint sanding is being done until all clean up is

completed.

2. A dust mask or respirator should be worn by all persons entering

the work area. The filter should be replaced daily or whenever the

wearer has difficulty breathing.

NOTE: Only those dust masks suitable for working with lead paint

dust and fumes should be used. Ordinary painting masks do not

offer this protection. See your local hardware dealer for the proper

NIOSH-approved mask.

3. NO EATING, DRINKING or SMOKING should be done in the work

area to prevent ingesting contaminated paint particles. Workers

should wash and clean up BEFORE eating, drinking or smoking.

Articles of food, drink, or smoking should not be left in the work

area where dust would settle on them.

ENVIRONMENTAL SAFETY

1. Paint should be removed in such a manner as to minimize the

amount of dust generated.

2. Areas where paint removal is occurring should be sealed with

plastic sheeting of 4 mils thickness.

English

17

3. Sanding should be done in a manner to reduce tracking of paint

dust outside the work area.

CLEANING AND DISPOSAL

1. All surfaces in the work area should be vacuumed and thoroughly

cleaned daily for the duration of the sanding project. Vacuum filter

bags should be changed frequently.

2. Plastic drop cloths should be gathered up and disposed of

along with any dust chips or other removal debris. They should

be placed in sealed refuse receptacles and disposed of through

regular trash pick-up procedures.

During clean up, children and pregnant women should be kept

away from the immediate work area.

3. All toys, washable furniture and utensils used by children should

be washed thoroughly before being used again.

Mounting and Using Wire Brushes

and Wire Wheels

Wire cup brushes or wire wheels screw directly on the grinder spindle

without the use of flanges. Use only wire brushes or wheels provided

with a 5/8"–11 threaded hub. A Type 27 guard is required when using

wire brushes and wheels.

CAUTION: To reduce the risk of personal injury, wear work

gloves when handling wire brushes and wheels. They can

become sharp.

CAUTION: To reduce the risk of damage to the tool, wheel or

brush must not touch guard when mounted or while in use.

Undetectable damage could occur to the accessory, causing wires to

fragment from accessory wheel or cup.

MOUNTING WIRE CUP BRUSHES AND WIRE WHEELS

1. Thread the wheel on the spindle by hand.

2. Depress spindle lock button and use a wrench on the hub of the

wire wheel or brush to tighten the wheel.

3. To remove the wheel, reverse the above procedure.

NOTICE: To reduce the risk of damage to the tool, properly seat the

wheel hub before turning the tool on.

USING WIRE CUP BRUSHES AND WIRE WHEELS (FIG. 16)

Wire wheels and brushes can be used for removing rust, scale and

paint, and for smoothing irregular surfaces.

NOTE: The same precautions should be taken when wire brushing

paint as when sanding paint (refer to Precautions To Take When

Sanding Paint).

1. Allow the tool to reach full speed before touching the tool to the

work surface.

2. Apply minimum pressure to work surface, allowing the tool to

operate at high speed. Material removal rate is greatest when the

tool operates at high speed.

3. Maintain a 5° to 10° angle between the tool and work surface

for wire cup brushes.

4. Maintain contact between the edge of the wheel and the work

surface with wire wheels.

5. Continuously move the tool in a forward and

5˚–10˚

FIG. 16

back motion to avoid creating gouges in

the work surface. Allowing the tool to rest

on the work surface without moving, or

moving the tool in a circular motion causes

burning and swirling marks on the work

surface.

6. Remove the tool from the work surface before turning the tool off.

Allow the tool to stop rotating before setting it down.

CAUTION: Use extra care when working over an edge, as a

sudden sharp movement of grinder may be experienced.

English

18

La page charge ...

DeWalt D28499 Manuel utilisateur

Ce manuel convient également à

DeWalt D28499 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents