Yamaha CL5 Manuel utilisateur

EN

How to Use This Reference Manual

The CL5/CL3/CL1 Reference Manual (this document) allows you to

search for terms and take advantage of links in the text.

Searching for terms

To search for a term, use the search function of the software you’re using

to view this document.

If you’re using Adobe Reader, enter the term in the search box and press

the <Enter> key of your computer keyboard to search for occurrences of

that term.

Displaying the next/previous view

If you’re using Adobe Reader, you can jump to the previous/next view in

your viewing history. This is a convenient way to jump back to the

previous page after you’ve used a link to jump to a different page.

Using the Function Tree

A function tree for the CL5/CL3/CL1 is provided on page 4 and

following. You can use this function tree to find the page that explains

an on-screen display or function.

Reference Manual

Contents

Reference Manual

2

Contents

How to Use This Reference Manual .......................................................................... 1

Function Tree ............................................................................ 4

SELECTED CHANNEL section ...................................................... 6

About the SELECTED CHANNEL section................................................................... 6

Operations in the SELECTED CHANNEL section ....................................................... 6

SELECTED CHANNEL VIEW screen ........................................................................... 7

Centralogic section ................................................................. 11

About the Centralogic section................................................................................ 11

Operations in the Centralogic section .................................................................... 11

OVERVIEW screen .................................................................................................. 12

Input and output patching..................................................... 15

CL console internal patching and Dante audio network patching .......................... 15

Changing the output patch settings ...................................................................... 16

Changing the input patch settings......................................................................... 19

Inserting an external device into a channel ............................................................ 21

Directly outputting an INPUT channel ................................................................... 23

Recording or playing back using DAW on a computer ........................................... 25

Input channels ........................................................................ 27

Signal flow for input channels................................................................................ 27

Specifying the channel name, icon and channel color............................................ 28

Making HA (Head Amp) settings............................................................................ 30

Sending a signal from an input channel to the STEREO/MONO buses ................... 35

Sending a signal from an input channel to a MIX/MATRIX bus .............................. 39

Correcting delay between channels (Input Delay).................................................. 44

Channel library operations..................................................................................... 45

Output channels ..................................................................... 46

Signal flow for output channels ............................................................................. 46

Specifying the channel name, icon and channel color............................................ 47

Sending signals from MIX channels to the STEREO/MONO bus ............................. 48

Sending signals from MIX channels and STEREO/MONO channels to

MATRIX buses............................................................................................. 51

Correcting delay between channels (Output Delay)............................................... 55

Channel library operations..................................................................................... 55

EQ and Dynamics ..................................................................... 56

About EQ and dynamics ......................................................................................... 56

Using EQ ................................................................................................................ 56

Using dynamics ...................................................................................................... 59

Using the EQ or Dynamics libraries ......................................................................... 63

Grouping and linking .............................................................. 64

About DCA groups and Mute groups ..................................................................... 64

Using DCA groups.................................................................................................. 64

Using mute groups................................................................................................. 66

Channel Link function ............................................................................................ 70

Copying, moving, or initializing a channel.............................................................. 73

Scene memory ......................................................................... 77

About scene memories ........................................................................................... 77

Using scene memories............................................................................................ 77

Editing scene memories.......................................................................................... 82

Using the Global Paste function.............................................................................. 85

Using the Focus function ........................................................................................ 87

Using the Recall Safe function................................................................................. 88

Using the Fade function.......................................................................................... 91

Outputting a control signal to an external device in tandem with scene recall

(GPI OUT) ................................................................................................... 93

Playing back an audio file that links to a scene recall............................................... 94

Using Preview mode............................................................................................... 96

Monitor and Cue functions ..................................................... 97

About the Monitor and Cue functions .................................................................... 97

Using the Monitor function .................................................................................... 98

Using the Cue function......................................................................................... 101

Operating the Cue function.................................................................................. 102

Talkback and Oscillator......................................................... 106

About the Talkback and Oscillator functions ......................................................... 106

Using Talkback ..................................................................................................... 106

Using the Oscillator function ................................................................................ 108

Meters.................................................................................... 111

Operations in the METER screen ........................................................................... 111

Using an MBCL meter bridge (optional) on the CL3 or CL1 console ..................... 113

Contents

Reference Manual

3

Graphic EQ, effects, and Premium Rack ............................... 114

About the virtual rack .......................................................................................... 114

Virtual rack operations ......................................................................................... 115

Graphic EQ operations......................................................................................... 118

About the internal effects..................................................................................... 122

Using the Premium Rack...................................................................................... 130

Using the graphic EQ, effect, and Premium Rack libraries..................................... 137

I/O device and external head amp ....................................... 138

Using an I/O device ............................................................................................. 138

I/O device patching ............................................................................................. 138

Remotely controlling an Rio unit.......................................................................... 140

Remotely controlling an amp............................................................................... 143

Using an external head amp ................................................................................ 144

MIDI....................................................................................... 149

MIDI functionality on the CL series console.......................................................... 149

Basic MIDI settings .............................................................................................. 149

Using Program Changes to recall scenes and library items ................................... 152

Using Control Changes to control parameters ..................................................... 155

Using Parameter Changes to control parameters ................................................. 157

User settings (Security) ........................................................ 158

User Level settings ............................................................................................... 158

Preferences .......................................................................................................... 168

USER DEFINED keys ............................................................................................. 169

USER DEFINED knobs........................................................................................... 171

Assignable encoders ............................................................................................ 172

Custom fader bank .............................................................................................. 173

Master fader ........................................................................................................ 174

Console Lock ....................................................................................................... 175

Saving and loading setup data to and from a USB flash drive............................... 177

Formatting a USB flash drive................................................................................ 180

Recorder................................................................................ 181

About the USB memory recorder ......................................................................... 181

Assigning channels to the input and output of the recorder................................. 181

Recording audio to a USB flash drive.................................................................... 183

Playing back audio files from a USB flash drive ..................................................... 185

Editing the title list............................................................................................... 187

Using the CL console with Nuendo Live............................................................... 188

Help function ........................................................................ 193

Loading a Help file from a USB flash drive............................................................ 193

Loading a text file from a USB flash drive.............................................................. 193

Viewing Help........................................................................................................ 194

Using USER DEFINED keys to recall Help directly................................................... 194

Other functions ..................................................................... 196

About the SETUP screen ....................................................................................... 196

Word clock and slot settings................................................................................. 198

Using cascade connections ................................................................................... 200

Basic settings for MIX buses and MATRIX buses.................................................... 202

Switching the entire phantom power supply on/off.............................................. 203

Specifying the brightness of the touch screen, LEDs, channel name displays,

and lamps ................................................................................................. 204

Setting the date and time of the internal clock ..................................................... 204

Setting the network address ................................................................................. 205

Initializing the unit to factory default settings ....................................................... 206

Adjusting the detection point of the touch screen (Calibration function) .............. 207

Adjusting the faders (Calibration function) ........................................................... 208

Fine-tuning the input and output gain (Calibration function) ............................... 209

Adjusting the channel color (Calibration function)................................................ 211

Adjusting the brightness of the channel name display .......................................... 212

Adjusting the contrast of the channel name display.............................................. 213

Dante audio network settings ............................................................................... 213

Using GPI (General Purpose Interface) .................................................................. 221

Appendices ............................................................................ 227

EQ Library List ...................................................................................................... 227

DYNAMICS Library List ......................................................................................... 228

Dynamics Parameters ........................................................................................... 230

Effect Type List ..................................................................................................... 232

Effects Parameters................................................................................................. 233

Premium Rack Processor Parameters ..................................................................... 245

Effects and tempo synchronization ....................................................................... 247

Parameters that can be assigned to control changes............................................. 248

NRPN parameter assignments .............................................................................. 250

Mixing parameter operation applicability ............................................................. 254

Functions that can be assigned to USER DEFINED keys ......................................... 259

Functions that can be assigned to USER DEFINED knobs....................................... 262

Functions that can be assigned to the assignable encoders................................... 263

MIDI Data Format ................................................................................................ 264

Warning/Error Messages....................................................................................... 271

Electrical characteristics ........................................................................................ 273

Mixer Basic Parameters......................................................................................... 274

MIDI Implementation Chart ................................................................................. 275

Index.................................................................................................................... 276

Function Tree

Reference Manual

4

Function Tree

Page numbers in parentheses ( ) are the page numbers of the

Owner’s Manual (booklet).

Main

SELECTED CHANNEL 6

OVERVIEW 12

FUNCTION ACCESS AREA (20)

CHANNEL PARAMETER

PATCH/NAME 16, 29, 48

GAIN/PATCH 31

1ch 31

8ch 32

CH1-48 32

CH49-72/ST IN 32

OUTPUT Indication only

INPUT DELAY 44

8ch 44

CH1-48 45

CH49-72/ST IN 45

DELAY SCALE 44

INSERT/DIRECT OUT 21

1ch 21, 23

8ch 22, 24

HPF/EQ 56

1ch 56

8ch 57

CH1-48 58

CH49-72/ST IN 58

OUTPUT 58

DYNAMICS 59

1ch 59

KEY IN SOURCE SELECT 62

8ch 61

CH1-48 62

CH49-72/ST IN 62

OUTPUT 62

SEND TO/SEND FROM 41, 52

TO STEREO/MONO 49

8ch 49

CH1-48 50

CH49-72/ST IN 50

OUTPUT 50

LIBRARY

CHANNEL LIBRARY 45

EQ LIBRARY 63

DYNAMICS LIBRARY 63

GEQ LIBRARY 137

EFFECT LIBRARY 137

Portico5033/Portico5043/U76/Opt-2A/

EQ-1A/DynamicEQ LIBRARY

137

DANTE INPUT PATCH LIBRARY 139

RACK

VIRTUAL RACK 115

RACK MOUNTER 116

GEQ EDIT 118

GEQ LINK 119

EFFECT RACK 122

EFFECT EDIT 125

EFFECT TYPE 126

PREMIUM RACK 130

PREMIUM RACK MOUNTER 131

PREMIUM RACK EDIT 132

I/O DEVICE

DANTE PATCH 138

DANTE SETUP 138

DANTE INPUT PATCH 138

DANTE OUTPUT PATCH 140

Rio 140

REMOTE HA EDIT 141

DANTE OUTPUT PATCH 142

AMP 143

DANTE OUTPUT PATCH 143

EXTERNAL HA 146

EXTERNAL HA EDIT 147

EXTERNAL HA PORT SELECT 147

MONITOR

MONITOR 98

CUE 103

MONITOR 99

OSCILLATOR 109

TALKBACK 107

METER

INPUT METER 111

OUTPUT METER 111

SETUP

USER SETUP 196

PREFERENCE 168

USER DEFINED KEYS SETUP 169

USER DEFINED KEY SETUP (List) 170

USER DEFINED KNOBS SETUP 171

USER DEFINED KNOB SETUP (List) 171

ASSIGNABLE ENCODER SETUP 172

CUSTOM FADER BANK/MASTER FADER 173

FADER ASSIGN SELECT 174

Function Tree

Reference Manual

5

NOTE

• The explanations in this reference manual will use the CL5.

• In the case of the CL3/CL1, some screens will not show

channels and faders that do not exist on those models.

USER LEVEL/CREATE USER KEY 158

CREATE KEY 160

SAVE KEY 165

LOGIN 161

SAVE/LOAD 177

WORD CLOCK/SLOT 198

CASCADE IN/OUT PATCH 200, 202

OUTPUT PORT 18

MIDI/GPI 149, 221

MIDI SETUP 150

PROGRAM CHANGE 152

CONTROL CHANGE 155

GPI 222

FADER START 225

BUS SETUP 202

CONSOLE LOCK 175

DATE/TIME 204

NETWORK 205

DANTE SETUP 213

SCENE

SCENE LIST 79

GLOBAL PASTE 85

FADE TIME 91

SONG SELECT 95

FOCUS RECALL 87

PREVIEW 96

RECORDER

USB 181

NUENDO LIVE 188

SETUP CH JOB

CH LINK MODE 71

DCA GROUP ASSIGN 64

MUTE GROUP ASSIGN 66

RECALL SAFE MODE 88

CH COPY MODE 73

CH MOVE MODE 74

CH DEFAULT MODE 76

PATCH

PORT SELECT

22, 24, 100, 104,

139, 201

CH SELECT

19, 117, 174,

175, 182

Others

CONFIRMATION 168

SOFT KEYBORD (21)

LOGIN 161

Startup Menu

MODE SELECT 206

INITIALIZE ALL MEMORIES 206

INITIALIZE CURRENT MEMORIES 206

TOUCH SCREEN CALIBRATION 207

INPUT PORT TRIM 210

OUTPUT PORT TRIM 210

SLOT OUTPUT TRIM 210

FADER CALIBRATION 208

CHANNEL COLOR CALIBRATION 211

SELECTED CHANNEL section

Reference Manual

6

SELECTED CHANNEL section

This chapter explains how to use the SELECTED CHANNEL section and the SELECTED CHANNEL

VIEW screen to control the selected channel.

About the SELECTED CHANNEL section

The SELECTED CHANNEL section located to the left of the display corresponds to the mixer module

on a conventional analog mixer, and enables you to manually adjust all the major parameters of the

currently-selected channel.

Operations in this section will affect the channel that was most recently selected by its [SEL] key. If you

have assigned an ST IN channel or STEREO channel to a single channel strip, either the L or the R

channel will be selected, and the major parameters for L and R channels will be linked. You can use the

knobs on the panel to control mix parameters such as head amp gain, HPF/EQ settings, the threshold

setting of the dynamics processors, pan/balance settings, and send levels to the MIX/MATRIX buses.

Operations in the SELECTED CHANNEL section

Follow the steps below to perform operations in the SELECTED CHANNEL section.

1. Use a [SEL] key to select the channel you want to control.

To select a channel, press a [SEL] key in the top panel channel strip section, the Centralogic

section, or the master section.

Press the appropriate bank select key so that the

channels you want to control are assigned to the

top panel.

The number and name of the currently-selected

channel is shown in the channel select field

located in the Function Access Area of the touch

screen.

NOTE

• If an ST IN channel or STEREO channel has

been assigned to a single channel strip, you can switch between L and R by repeatedly pressing

the same [SEL] key.

• You can also switch channels by pressing the channel select field located in the Function Access

Area. Press the left side of the field to select the preceding channel. Press the right side of the

field to select the next channel.

2. Press one of the knobs in the SELECTED CHANNEL section.

Press a knob in the SELECTED CHANNEL section to display the SELECTED CHANNEL VIEW

screen for the currently-selected channel. If you leave this screen displayed, you will always be able

to view the settings in the screen while operating the knobs in the SELECTED CHANNEL

section.

NOTE

If you have turned on the option “POPUP APPEARS WHEN KNOB(S) PRESSED” on the

PREFERENCE tab (accessed by pressing the SETUP button, then the USER SETUP button),

pressing a knob repeatedly will open or close the popup window (1ch).

Even if a different screen is selected, the knobs in the SELECTED CHANNEL section will always

affect the currently-selected channel. In this case, a window indicating the value of that parameter

will appear on screen when you operate a knob.

3. Use the knobs in the SELECTED CHANNEL section and the buttons on the

SELECTED CHANNEL VIEW screen to edit the parameters of the selected channel.

Channel number

Channel name

SELECTED CHANNEL section

Reference Manual

7

SELECTED CHANNEL VIEW screen

■ SEND field

In this field, you can view the send level from the channel to each MIX/

MATRIX bus, switch the on/off status of the send signals, and switch between

pre and post.

1 Tabs

Enable you to select a group of 16 output bus channels to be displayed

in the SEND field.

• MIX1–16 tab.............................. displays MIX buses 1–16.

• MIX17–24/MATRIX tab......... displays MIX buses 17–24 and

MATRIX buses 1–8.

The view and the function of the knobs and buttons in the SEND field vary

depending on whether a pair of bus channels (odd-numbered and even-

numbered) are comprised of two mono channels or a stereo channel.

If the destination bus channels are two mono channels:

1 SEND knob

Sets the send level to the corresponding bus.

2 PRE indicator

Indicates the send point of the corresponding bus. If the PRE button on the MIX SEND 8ch screen

is turned ON, this PRE indicator will be turned on.

3 ON button

Switches the send signal to the corresponding bus on or off.

If the destination bus is a stereo channel:

1 SEND/PAN knob

The right-hand knob adjusts the level of the signal sent to a pair of bus channels (even-numbered

and odd-numbered). The left-hand knob adjusts the pan and balance of the same signal.

2 PRE indicator

Indicates the send point of the corresponding bus. If the PRE button on the MIX SEND 8ch screen

is turned ON, this PRE indicator will be turned on.

3 ON button

Press the right-hand button to switch on or off the signal sent to two bus channels.

NOTE

• If the indices of a SEND/PAN knob are white, the send point is assigned as PRE; if the indices

are black, it is assigned as POST.

• If the send point is PRE, you can specify the PRE point as either VARI [PRE EQ] or VARI [PRE

FADER] in the BUS SETUP popup that appears when you press the SETUP button → BUS

SETUP button.

• If the type of the destination bus is set to FIXED, controllers

1–2 mentioned above will not be

displayed. The send level will be fixed at nominal level, and the send point will be fixed at POST

FADER. For details, see “Basic settings for MIX buses and MATRIX buses” on page 202.

• Press the SEND LEVEL knob or PAN knob on screen to open the SEND 8ch popup window.

1

2

3

1

2

3

SELECTED CHANNEL section

Reference Manual

8

■ GAIN/PATCH field

This field enables you to make HA (head amp) analog gain settings, and view the operational status of

the head amp.

1 GAIN knob

Sets the analog gain of the head amp.

For a channel to which the head amp has not been

patched, a gray circle appears, instead of the knob. Press

the knob to open the GAIN/PATCH 1ch popup window.

If the Gain Compensation function is turned on, an

indicator appears, showing the level of the signal output

to the audio network.

2 OVER indicator

Warns you when the signal is clipping.

3 +48V indicator

Indicates the phantom power on or off status for the head amp.

4 Ø (Phase) indicator

Indicates the input phase setting for the head amp.

NOTE

• For an input channel that is patched to an input that has no head amp, 1 will be a gray circle

and

3 will not be shown. For an output channel, 1 will be a gray circle, and 2–4 will not be

shown.

• If GAIN KNOB FUNCTION is set to DIGITAL GAIN in the USER SETUP → PREFERENCE

screen, the digital gain knob will appear for

1, and 3 will not be displayed.

For details, refer to “Making HA (Head Amp) settings” on page 30.

■ PAN/BALANCE field

This field enables you to switch the on/off status of the signal sent from the selected channel to the

STEREO/MONO bus, and adjust the pan and balance.

The view and the function of the controllers in this field vary depending on the type of the selected

channel.

When an input channel or MIX channel is selected:

1 TO STEREO PAN knob

Sets the pan position of a signal routed to the STEREO

bus.

Press the knob to open the STEREO/MONO 8ch popup

window. If the ST IN channel is selected, you can specify

whether to view the PAN knob or the BALANCE knob in

this popup window. For a MIX channel, the PAN knob

will appear if the signal is mono, and the BALANCE

knob will appear if the signal is stereo.

2 ST/MONO button

Switches the on/off status of a signal sent from the

channel to the STEREO/MONO bus.

If an INPUT/MIX channel is set to LCR mode, the LCR

button appears in location 2.

The LCR button is an overall on/off switch for the signals

sent from the channel to the STEREO/MONO bus.

When a MATRIX, STEREO, or MONO channel is selected:

1 BALANCE knob

If the signal on the selected channel is stereo, the

BALANCE knob will appear, enabling you to adjust the

volume balance for the left and right channels. If the

channel signal is monaural, a gray circle will appear in

this location.

Press the knob to open the TO STEREO 8ch popup

window.

■ INPUT DELAY field

This field enables you to view the delay settings.

1 ON indicator

Indicates the on/off status of the delay. If the delay is off,

the indicator will not be displayed.

2 Delay time

The delay value is displayed by milliseconds (ms) and also by currently-selected scale. If the scale

uses units of ms, the value in the bottom row will not be displayed. Only the ms value appears in

the middle row.

Press this field to open the INPUT DELAY 8ch popup window.

■ HPF field (input channels only)

This field enables you to set the HPF.

1 HPF knob

Sets the HPF cutoff frequency.

2 ON button

Switches the HPF on or off.

If an output channel is selected, a gray circle will appear in location

1, and button 2 will be hidden.

2

3

4

1

1 2

2

1

2

1

2

SELECTED CHANNEL section

Reference Manual

9

■ EQ parameter field

This field displays the 4-band EQ parameter settings.

1 Q knob

Specifies the Q for each band.

If the HIGH band filter type is set to LPF or H. SHELF (high-

shelving), or the LOW band filter type is set to L. SHELF (low-

shelving), the Q knob will not be displayed. Only the filter type

name will be displayed.

NOTE

• Fully rotating the HIGH band Q knob on the panel counter-clockwise while pressing and holding

it down will set the filter type to LPF. Fully rotating the Q knob clockwise while pressing and

holding it down will set the filter type to high-shelving.

• Fully rotating the LOW band Q knob on the panel clockwise while pressing and holding it down

will set the filter type to low-shelving.

• If an output channel has been selected, fully rotating the LOW band Q knob on the panel counter-

clockwise while pressing and holding it down will set the filter type to HPF.

• You can also switch the filter type on the HPF/EQ 1ch popup window.

2 FREQUENCY knob

Sets the center frequency (or cutoff frequency) for each band.

3 GAIN knob

Sets the amount of cut/boost for each band.

NOTE

• If the HIGH band filter type is set to LPF, you can switch LPF on or off using the HIGH band GAIN

knob on the panel.

• If the LOW band filter type is set to HPF, you can switch HPF on or off using the LOW band GAIN

knob on the panel.

• Press each knob to open the HPF/EQ 1ch popup window.

■ EQ graph field

This field graphically indicates the approximate response of the EQ. Press this field to open the HPF/

EQ 1ch popup window, in which you can set the attenuator, HPF and EQ.

■ DYNAMICS 1/DYNAMICS 2 field

This field enables you to view and set the Dynamics 1/2 parameters.

1 OVER indicator

Warns you when the signal is clipping.

2 Level meter

Displays the output signal level (green) and the amount of gain reduction (orange) when the

Dynamics is on. The current threshold setting is shown as a white vertical line.

3 Threshold

Specifies the threshold.

4 Parameters

Indicate the values of parameters that vary depending on the currently-selected dynamics type.

Press this field to open the DYNAMICS 1/DYNAMICS 2 1ch popup window, in which you can

make detailed parameter settings.

1 2 3

1 2

3

4

SELECTED CHANNEL section

Reference Manual

10

■ INSERT field

This field enables you to make insert settings.

1 Popup button

Press this button to open the INSERT/DIRECT OUT 1ch

popup window.

2 ON button

Switches the insert on or off.

3 RACK EDIT popup button

Appears if an effect or Premium Rack is inserted. Press this button to display the edit screen for

the inserted rack.

4 IN indicator

Appears if a port has been assigned to the insert-in patch. It lights when the signal is sent to the

insert-in.

■ DIRECT OUT field

This field enables you to make insert settings.

1 Popup button

Press this button to open the INSERT/DIRECT OUT 1ch

popup window. The Direct Out level value will appear below

the button.

2 ON button

Switches the Direct Out on or off.

■ RECALL SAFE field

This field enables you to make Recall Safe settings.

1 Popup button

Press this button to open the RECALL SAFE popup window.

2 ON button

Switches the Recall Safe status on or off.

3 PARTIAL indicator

This will light if recall safe applies only to some of the parameters, not to all channel settings.

■ FADER field

This field enables you to view and make settings for the channel on/

off status and the level.

1 Fader

Displays the current level.

Use the faders on the top panel to set the levels.

2 Level indicator

Displays the current level setting by numerical value. If the

signal is clipping at any point in the channel, the ΣCLIP indicator will light.

3 ON button

Switches the channel status on or off. The button is linked with the corresponding [ON] key on

the top panel.

■ DCA/MUTE field

This field enables you to view and select the DCA or mute group to which

the channel is assigned.

1 Tabs

Select DCA or mute as a group to set. Press the selected tab once again

to open the DCA/MUTE GROUP ASSIGN MODE popup window.

When the DCA group tab is selected:

2 DCA group select buttons

Select the DCA group to which the channel is assigned.

3 Mute group indicators

Indicate the mute group to which the channel is assigned.

When the mute group tab is selected:

4 Mute group select buttons

Select the mute group to which the channel is assigned.

NOTE

If the dimmer level is set to the mute group, this button lights

orange.

5 MUTE SAFE button

Temporarily removes the channel from the mute group.

6 DCA group indicators

Indicate the DCA group to which the channel is assigned.

1

2

4 3

21

2

1

3

1

2

3

1

3

2

4

5

6

Centralogic section

Reference Manual

11

Centralogic section

This chapter explains how to use the Centralogic section and the OVERVIEW screen to simultaneously

control up to eight channels.

About the Centralogic section

The Centralogic section is located below the touch screen, and lets you recall and simultaneously

control a set of up to eight input channels, output channels, or DCA groups. Use the Bank Select keys

in the Centralogic section to select the channels that you want to control.

If you press one of the Bank Select keys, the channels or DCA groups corresponding to that key will be

assigned to the Centralogic section, and can be controlled using the faders, [ON] keys, and [CUE] keys

in the Centralogic section.

Operations in the Centralogic section

Follow the steps below to perform operations in the Centralogic section.

1. Use the Bank Select keys in the Centralogic section to select the channels or DCA

groups that you want to control.

When you press a Bank Select key, the LED of that key will light. The touch screen will display the

OVERVIEW screen, and the parameters of the eight channels you selected will appear.

NOTE

When the SELECTED CHANNEL VIEW screen is displayed, you can switch to the OVERVIEW

screen by pressing any of the multifunction knobs 1–8. This is convenient if you want to quickly

switch to the OVERVIEW screen while leaving the same channels or DCA groups selected for

control.

2. Use the faders and [ON] keys in the Centralogic section to adjust the level of the

group of up to eight selected channels and switch them on or off.

NOTE

• The bottom line of the OVERVIEW screen shows the channels or DCA groups that can be

controlled by the faders, [ON] keys and [CUE] keys in the Centralogic section.

• The top line of the OVERVIEW screen shows the channels that can be controlled by multifunction

knobs 1–8 in the Centralogic section.

3. Use the fields on the OVERVIEW screen and the multifunction knobs to adjust the

parameters for the group of up to eight channels.

Bank Select keys

Centralogic section

Reference Manual

12

OVERVIEW screen

■ CHANNEL NAME field

This field appears at the top and bottom of the screen and displays the channel number, name, and icon

for the currently-selected eight channels. The name of the currently-selected channel is highlighted.

NOTE

If you have retained the channels assigned to the faders in the Centralogic section by pressing

and holding down a Bank Select key, the channel names shown at the top and bottom of the

OVERVIEW screen may differ.

■ GAIN/PATCH field

This field enables you to make HA (head amp) analog or digital gain settings and view the operational

status of the head amp.

The view and the function of the controllers in this field vary depending on the type of the selected

channel.

If the head amp is patched:

1 GAIN knob

Sets the analog gain of the head amp.

• Press this field to assign the GAIN knob to the corresponding

knob in the Centralogic section, which enables you to adjust the gain. If the Gain

Compensation function is turned on, an indicator appears, showing the level of the signal

output to the audio network.

• If the GAIN knob has been assigned to a knob in the Centralogic section, press the knob to open

the GAIN/PATCH 8ch popup window.

2 OVER indicator

Lights when the signal at the input port or from the rack output exceeds the full scale level. This

indicator is available only if an input channel is selected.

3 +48V indicator

Indicates the phantom power (+48V) on or off status for the head amp. This indicator is not

displayed unless the head amp is patched to the channel.

4 Ø (Phase) indicator

Indicates the input phase setting for the head amp. This indicator is available only if an input

channel is selected.

NOTE

• If the slot is not connected to the head amp, the patch and the type of the MY card will be

displayed.

• If GAIN KNOB FUNCTION is set to DIGITAL GAIN in the PREFERENCE screen, the digital GAIN

knob will appear instead of knob

1, and indicator 3 will not be displayed.

If the Gain Compensation function is turned on, an indicator appears, showing the level of the

signal output to the audio network.

If the slot is patched:

The slot name will appear.

If the rack is connected:

The patch and module name will appear.

If the output is connected:

Only the patch will appear.

: Selected channel

: Unselected channel

1

4

3

2

Centralogic section

Reference Manual

13

■ INPUT DELAY field

This field displays the delay status for the input channel. If an output channel has been selected, this

field will be blank. Press this field to open the INPUT DELAY 8ch popup window.

1 DELAY ON/OFF indicator

Indicates the on/off status of the delay.

■ INSERT/DIRECT OUT field

This field enables you to make insert and Direct Out settings. Press this field to open the INSERT/

DIRECT OUT 8ch popup window.

1 INSERT ON/OFF indicator

Indicates the insert on/off status.

2 DIRECT OUT ON/OFF indicator (input channels only)

Indicates the Direct Out on/off status.

■ EQ field

This field graphically indicates the approximate response of the EQ.

Press this field to open the HPF/EQ 1ch popup window, in which

you can set the HPF and EQ.

NOTE

If DCA or monitor has been selected, this field will be blank.

■ DYNAMICS 1/2 field

This field displays the threshold value and meter for Dynamics 1/2.

Press this field to open the DYNAMICS 1/2 1ch popup window.

NOTE

If DCA or monitor has been selected, this field will be blank.

■ SEND field

This field displays the send level, send on/off status, and pre/post settings for 16

buses.

To select the 16 destination buses, use the [MIX 1–16] or [MIX 17–24/MATRIX]

key in the SELECTED CHANNEL section on the panel.

Use the Centralogic multifunction knobs to adjust the send level for each bus.

Touch the knob of the bus you want to operate; it will be assigned to the

Centralogic multifunction knobs. If it is assigned to the multifunction knobs,

touching that knob once again will display the SEND 8ch popup screen.

This field varies depending on the type of the destination bus.

If the destination bus is VARI (mono):

The knob color and scale color indicate the send on/off and pre/post status. If

the send is off, the knob color turns gray. With the post setting, the knob scale

color turns black.

If the destination bus is VARI (stereo):

If a pair of buses (odd-numbered and even-numbered) are in stereo, the left-

hand knob will function as the PAN knob, and the right-hand knob will function

as the SEND knob.

If the destination bus is set to FIXED:

The SEND ON/OFF button will appear instead of each knob.

1

2

Centralogic section

Reference Manual

14

■ TO STEREO/MONO field

This field displays the on/off status and pan/balance setting of the signal sent to the STEREO/MONO

bus.

If you press this field, the knob will be assigned to the corresponding knob in the Centralogic section.

If you press the field once again, the TO STEREO/MONO 8ch popup window will appear.

This field varies depending on the type of the selected channel.

When an input channel or MIX channel is selected:

1 TO STEREO PAN knob

Sets the pan position of a signal routed to the STEREO bus.

Press the knob to open the STEREO/MONO 8ch popup window. If the ST IN channel is selected,

you can specify whether to view the PAN knob or the BALANCE knob in this window. For a MIX

channel, the PAN knob will appear if the signal is mono, and the BALANCE knob will appear if

the signal is stereo.

2 ST/MONO indicator

Indicates the status of a signal sent to the STEREO/MONO bus.

If an input or MIX channel is set to LCR mode, the LCR indicator will

be displayed in location 2.

When a MATRIX channel (monaural) or MONO channel is selected:

The ΣCLIP indicator appears, indicating that the signal is clipping at some point in the channel.

For a stereo MATRIX channel or STEREO channel, the BALANCE knob appears, indicating the

balance of the left/right channels.

■ DCA group field

A DCA group (1–16) to which the channel is assigned is displayed on the first or second row in this

field.

Press this field to open the DCA/MUTE GROUP ASSIGN MODE popup window.

■ Mute group field

A mute group (1–8) to which the channel is assigned is displayed on the third row in this field. If the

channel has been temporarily removed from the mute group, “S” (Safe) will appear on the third row.

If the dimmer level has been set for a mute group, the color of the characters changes from red to

orange.

Press this field to open the DCA/MUTE GROUP ASSIGN MODE popup window.

1

2

Input and output patching

Reference Manual

15

Input and output patching

This chapter explains how to edit the input patching and output patching, how to connect inserts, and

how to use direct outputs.

CL console internal patching and Dante audio

network patching

The following diagram shows the signal flow through the CL series console, I/O devices, and Dante

audio network.

Input patching

CL series consoles and I/O devices feature two types of patching: Dante audio network patching and

CL console internal patching.

For Dante audio network patching, you will use the DANTE INPUT PATCH popup window. In this

window, you can patch CL console and I/O device inputs. Sixty-four (64) channels can be input from a

Dante audio network to a CL series console. You can choose up to 64 channels from maximum of 512

channels (logical value) of Dante audio network signals. Select the I/O devices (within 64 channels) that

you want to control from the CL series console.

Then, route the input signals (that were patched in the DANTE INPUT PATCH popup window) to

channels on the CL series console. To do this, choose input ports from DANTE 1–64 in the GAIN/

PATCH popup window.

NOTE

By default, DANTE 1–64 are assigned to input channels 1–64.

Output patching

Use the OUTPUT PORT popup window to patch CL console’s output channels and Dante audio

network. In this window, assign output channel signals to DANTE 1–64 ports.

NOTE

By default, MIX 1–24 are assigned to DANTE 1–24, MATRIX 1–8 are assigned to DANTE 25–32,

STEREO L/R are assigned to DANTE 33/34, and MONO is assigned to DANTE 35.

Next, patch the output signals from DANTE 1–64 (assigned in the OUTPUT PORT popup window) to

I/O device outputs. Use the OUTPUT PATCH popup window of the I/O device to make these

assignments.

64/512

8 16 16 16 64

SW

Dante-MY16-AUD

ID #3

ID #1

ID #2

OMNI MY MY MY

INPUT PATCH

Dante Network

“Dante” (ports)

CL series console

I/O device

Up to 512 channels

(logical value)

Dante

patching

CL internal

patching

Input and output patching

Reference Manual

16

Changing the output patch settings

To change the patching, you can either select the output port that will be the output destination of each

output channel, or you can select the output channel that will be the output source for each output port.

Selecting the output port for each output channel

1. Use the Bank Select keys in the Centralogic section to access the OVERVIEW screen

containing the output channel for which you want to assign the output port.

2. In the top part of the screen, press the channel number/channel name field to

access the PATCH/NAME popup window.

In the PATCH/NAME popup window you can change the channel name, icon, and output port

assigned to each output channel. The window includes the following items.

1 PATCH button

Indicates the port that is patched to the input or output channel. Press this button to enable the

PATCH tab at the bottom of the screen. The PORT SELECT popup window will appear, enabling

you to select the network and port.

2 Channel select button

Selects the channel to set.

NOTE

Switching channels on this screen will not affect the channel selection on the console.

3 Channel icon button

Indicates the icon and color that are currently selected for the corresponding channel. Press this

button to enable the ICON tab at the bottom of the screen. The CH COLOR/ICON popup

window will appear, enabling you to select the color, icon, and channel name.

4 Channel number display box

Indicates the channel number. This item cannot be changed.

Channel number/Channel name

3 54

1

6

7

2

Input and output patching

Reference Manual

17

5 Channel name edit box

Indicates the currently-specified channel. Press the inside of this box to enable the NAME tab at

the bottom of the screen. The SOFT KEYBOARD popup window will appear, enabling you to edit

the channel name.

6 Category select list

Selects the type of the port you want to display on the screen.

7 Port select buttons

Enable you to select a port in the current category. To cancel the selection, press the same button

once again.

3. Use the output port select tabs and the output port select buttons to specify the

output port that will be assigned to that channel.

If the output port select buttons are not shown at the bottom of the window, press the PATCH tab.

4. Use the Bank Select keys and the [SEL] keys to switch the output channels being

controlled, and specify their output ports in the same way.

5. When you have finished making settings, press the “x” symbol located in the upper

right to close the window.

You will return to the OVERVIEW screen.

Selecting the output channel for each output port

1. In the Function Access Area, press the SETUP button to access the SETUP screen.

2. In the SYSTEM SETUP field located in the center of the screen, press the OUTPUT

PORT button to open the OUTPUT PORT popup window.

OUTPUT PORT button

Input and output patching

Reference Manual

18

In the OUTPUT PORT popup window, you can assign the source channel for each output port.

This popup window includes the following items.

1 Slot number/Card type

If an output channel of slot 1–3 is selected for operations, this area indicates the slot number and

the type of I/O card installed in that slot.

2 DELAY SCALE button

Press this button to open the DELAY SCALE popup window, in which you can select the unit for

the delay time.

3 Output port

This is the type and number of the output port to which the channel is assigned.

4 Channel select popup button

Enables you to select the channel that you want to assign to the output port. The name of the

currently-selected channel is displayed.

5 Delay time knob

Sets the delay time of the output port. Press this knob to select it, and then use multifunction

knobs 1–8 to adjust the settings. The millisecond delay time value is indicated above the knob,

and the delay time value in the units selected in the DELAY SCALE popup window is indicated

below the knob.

NOTE

If you have selected ms (millisecond) as the scale, the delay time value will not appear above the

knob.

6 DELAY button

Switches the output port delay on or off.

7 Ø (Phase) button

Switches the phase of the signal assigned to the output port between normal phase and reverse

phase.

8 GAIN knob

Adjusts the output gain of the output port. To adjust this value, press the knob on screen to select

it, and then operate multifunction knobs 1–8. Rotate the knob to set the value in the range of –96

to +24 dB in 1.0 dB steps. Rotate the knob while pressing and holding it down to set the value in

0.1 dB steps. The current value appears immediately below the knob.

9 Level meter

Indicates the level of the signal assigned to the output port.

0 Output port select tabs

Switch the output ports controlled in the popup window in groups of up to eight ports. Tabs are

categorized into three groups: DANTE, SLOT, and PATCH VIEW. To display tabs in the desired

group, press the group name button located at the right or left end of the bottom row.

3. Use the output port select tabs at the bottom of the popup window to select the

output port you want to control.

The tabs correspond to the following output ports.

• DANTE 1–8, 9–16, 17–24, 25–32, 33–40, 41–48, 49–56, 57–64

These tabs control the output channels of the Dante connectors.

• SLOT1 1–8, 9–16

• SLOT2 1–8, 9–16

• SLOT3 1–8, 9–16

These tabs enable you to control output channels 1–8 and 9–16 of slots 1–3 respectively.

• OMNI 1–8

This tab enables you to control OMNI jacks 1–8.

• DIGITAL OUT

This tab enables you to control the L/R channels of the DIGITAL OUT connector.

•PATCH VIEW1

•PATCH VIEW2

These tabs display lists of patches.

4. To assign a channel to an output port, press the channel select popup window for

that port.

2

1

3

4

5

6

7

8

9

0

Input and output patching

Reference Manual

19

The CH SELECT popup window will appear. This popup window includes the following items.

1 Category select list

Selects the category of channel shown in the popup window. The categories correspond to the

following channels. They vary depending on the output port type.

• MIX/MATRIX.................................. MIX 1–MIX 24, MATRIX 1–MATRIX 8

• ST/MONO/MONI/CUE ................. STEREO L, STEREO R, MONO(C), MONI L, MONI R,

MONI C, CUE L, CUE R

• DIRECT OUT 1–32......................... CH1–CH32 Direct Outs

• DIRRECT OUT 33–64.................... CH33–CH64 Direct Outs

• DIRECT OUT 65–72 ...................... CH65–CH72 Direct Outs

• INSERT OUT 1–32.......................... CH1–CH32 Insert-outs

• INSERT OUT 33–64 ....................... CH33–CH64 Insert-outs

• INSERT OUT 65–72 ....................... CH65–CH72 Insert-outs

• INSERT OUT MIX/MATRIX ....... Insert-outs for MIX1-MIX24, MATRIX 1-MATRIX8

• INSERT OUT ST/MONO .............. Insert-outs for STEREO L, STEREO R, and MONO (C)

• CASCADE MIX/MATRIX............. MIX1–MIX24, MATRIX1–MATRIX8

• CASCADE ST/MONO/CUE.......... STEREO L, STEREO R, MONO(C), CUE L, CUE R

NOTE

In the case of the CL3/CL1, channels that do not exist on those models will not be shown.

2 Channel select buttons

Select the channel to be assigned to the output port you selected in step 3.

5. Use the channel select tabs and the channel select buttons to select the source

channel, and press the CLOSE button.

You will return to the OUTPUT PORT popup window.

NOTE

If PATCH CONFIRMATION is ON, a confirmation dialog box will appear when you attempt to

change the patch settings. If STEAL PATCH CONFIRMATION is ON, a confirmation dialog box

will appear when you attempt to change a location that is already patched elsewhere.

6. Make settings for delay, phase, and output gain as necessary.

7. Repeat steps 3–6 to assign channels to other output ports.

8. When you have finished making settings, click the “x” symbol in the upper right of

the window to return to the previous screen.

Changing the input patch settings

This section explains how to change the patching of each input channel.

1. Use the Bank Select keys in the Centralogic section to access the OVERVIEW screen

for the input channel to which you want to assign the input source.

2. In the top part of the screen, press the channel number/channel name field to

access the PATCH/NAME popup window.

1

2

Input and output patching

Reference Manual

20

In the PATCH/NAME popup window you can view and change the channel name, icon, channel

color, and input port assigned to each input channel.

1 PATCH button

Indicates the currently-selected input port. If you press this button when selecting an icon or

changing the channel name, you will return to the input port select screen.

2 Channel icon button

Indicates the icon that is selected for the corresponding channel. When you press this button, a

screen will appear in which you can select an icon or sample name.

3 Channel name input box

Indicates the name that is assigned to the corresponding channel. When you press this field, a

keyboard window allowing you to assign a name will appear.

4 Category select list

Selects the category of input port shown in the popup window. The categories correspond to the

following input ports. They vary depending on the channel type.

• DANTE1–32 ..............DANTE1–DANTE32

• DANTE33–64 ............DANTE33–DANTE64

• OMNI/PB OUT.........OMNI1–OMNI8, PB OUT(L), PB OUT(R)

• SLOT1 .........................SLOT1(1)–SLOT1(16)

• SLOT2 .........................SLOT2(1)–SLOT2(16)

• SLOT3 .........................SLOT3(1)–SLOT3(16)

• EFFECT RACK......... FX1L(A)–FX8R(B)

• PREMIUM RACK.... PR1L(A)–PR2R(B)

5 Input port select buttons

Assign an input port to the currently-selected input channel.

6 Tabs

Enable you to switch between items.

3. Access the input port selection screen of the PATCH/NAME popup window, and

then use the input port select tabs and input port select buttons to select an input

port.

NOTE

If PATCH CONFIRMATION is ON, a confirmation dialog box will appear when you attempt to

change the patch settings. If STEAL PATCH CONFIRMATION is ON, a confirmation dialog box

will appear when you attempt to change a location that is already patched elsewhere.

4. When you have finished making settings, press the “x” symbol located in the upper

right to close the window.

You will return to the OVERVIEW screen.

NOTE

You can also select input ports from the GAIN/PATCH popup window.

5. Repeat step 2–4 to assign input ports for other channels.

2 3

1

6

4

5

La page charge ...

Yamaha CL5 Manuel utilisateur

Ce manuel convient également à

Yamaha CL5 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents