Simplicity 1696920-00 Manuel utilisateur

Not for

Reproduction

80029886USCN

Revision B

Not for

Reproduction

2

Manual Contents:

General Information..............................................................2

Operator Safety..................................................................... 2

Features and Controls.........................................................4

................................................................................................ 6

Maintenance and Adjustments..........................................12

Storage................................................................................. 19

Troubleshooting Chart....................................................... 19

Specifications......................................................................20

General Information

For additional information, refer to theCustomer Contact

Guideincluded with the unit.

The illustrations in this document are representative.

Your unit might look different from the images

shown.LEFTandRIGHTare referenced from the operator's

position.

The use of Important and Note in the text shows clarifications,

exceptions, or alternatives to the procedures.

All language translations of this document derive from the

initial English source file.



Recycle all packaging, used oil, and batteries according to

applicable government regulations.

Operator Safety

Save these instructions

Save these instructions for future reference.This manual

contains safety information to make you aware of the hazards

and risks associated with the product and how to avoid them.

It also contains important instructions that must be obeyed

during the initial set-up, operation, and maintenance of the

product.

The snowthrower is designed and intended only for snow

removal from hard-surfaces, ground-level walkways, and

driveways. It is not intended for any other purpose.

It is important that you read and understand these instructions

before you attempt to start or operate this equipment.

Be thoroughly familiar with the controls and the correct use of

the snowthrower.

Know how to stop the unit and disengage the controls

quickly.

Safety Alert Symbol and Signal Words

The safety alert symbol identifies safety information

about hazards that can result in personal injury. A signal word

(DANGER,WARNING, orCAUTION) is used with the alert

symbol to indicate the likelihood and the potential severity of

injury. In addition, a hazard symbol may be used to represent

the type of hazard.

 DANGERindicates a hazard which, if not

avoided,willresult in death or serious injury.

 WARNINGindicates a hazard which, if not

avoided,couldresult in death or serious injury.

 CAUTIONindicates a hazard which, if not

avoided,couldresult in minor or moderate injury.

NOTICEindicates an action that could result in damage to

the product.

Snowthrower Hazard Symbols

Symbol Meaning Symbol Meaning

Safety information

about hazards that

can result in personal

injury.

Read and understand the

Operator's Manual before

you operate or service the

unit.

Amputation hazard -

rotating impeller.

Remove the key, and

readthe Operator's

Manualbefore you service

the unit.

Amputation hazard -

rotating impeller

Amputation hazard -

rotating auger

Amputation hazard -

do not touch moving

parts.

Thrown objects hazard

Fire hazard Explosion hazard

Shock hazard Toxic fume hazard

Hot surface hazard Kickback hazard

Keep a safe distance Keep children away

Not for

Reproduction

3

Symbol Meaning Symbol Meaning

Wear safety glasses — — — — — —

Safety Messages

WARNING

This product can expose you to chemicals including

gasoline engine exhaust, which is known to the State of

California to cause cancer and carbon monoxide, which

is known to the State of California to cause birth defects

or other reproductive harm. For more information go to

www.P65Warnings.ca.go.

DANGER

This snowthrower is capable of amputating hands and

feet, and throwing objects. Read and observe all the safety

instructions in this manual. Failure to do so could result in

death or serious injury.

Hand contact with the rotating auger inside the discharge

chute is the most common cause of injury associated with

snowthrowers.

WARNING

Read, understand, and follow all the instructions on the

snowthrower and in the Operator's Manual before you

operate this unit. Failure to obey the safety instructions in

this manual could result in death or serious injury.

• Only let operators who are responsible, trained, familiar

with the instructions and physically capable to operate

the machine.

WARNING

Always wear safety glasses or eye shields during operation

or while performing an adjustment or repair to protect eyes

from foreign objects that may be thrown from the machine.

U.S.A. Models: It is a violation of California Public Resource

Code Section 4442 to use or operate the engine on any

forest-covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as

defined in Section 4442, maintained in effective working

order. Other states or federal jurisdictions may have similar

laws. Contact the original equipment manufacturer, retailer,

or dealer to obtain a spark arrester designed for the exhaust

system installed on this engine.

Safety Decals

Before you operate the unit, read the safety decals. Compare

Figure1to the table that follows. The cautions and warnings

are for your safety. To avoid personal injury or damage to the

unit, understand and obey all the safety decals.

Important:If the safety decals become worn or damaged,

and cannot be read, order replacement decals from your local

dealer.

1

A

B

Not for

Reproduction

4

C

Features and Controls

Compare Figure2with the table below.

2

Not for

Reproduction

5

Snow Thrower Features and Controls

A Fuel Shut-Off Valve(if equipped)

B Throttle Control(if equipped)

C ON / OFF switch

D Choke closed / Choke open

E Primer button

F Alternate Choke-Prime Instructions

G Auger ControlLever

H Speed ControlLever

I Chute and Deflector Control Switch (if

equipped)

J Traction ControlLever

K Grip Warmer Switch(if equipped)

Note:Not all models feature heated hand grips.

L Clean-Out Tool

M Skid Shoes

N Headlight(if equipped)

O Steering Control

Free Hand™ Control After you engage the traction control (J) and the

auger control (G), this lets the operator release the

auger control lever to use other controls.

Not for

Reproduction

6

WARNING

This snowthrower is only as safe as the operator. If it is

misused, or not maintained correctly, it can be dangerous.

Remember you are responsible for your safety and those

around you.

• When leaving the operating position always disengage

the auger, STOP the engine, and remove the key. DO

NOT leave a running machine unattended.

• DO NOT operate the snowthrower without the correct

guards, and other safety protective devices in place and

working.

• Be careful when you operate the unit on gravel

driveways, walkways, or roads. Stay alert for hidden

hazards or traffic.

• DO NOToperate the snowthrower without good

visibility or light. Always be sure of your footing, and

keep a firm hold on the handles. Walk; never run.

• Be careful to avoid slipping or falling, especially when

you operate the snowthrower in reverse.

• Be careful when you operate the snowthrower on

slopes.

• If you strike a foreign object, stop the engine, remove

the wire from the spark plug, thoroughly inspect the

snowthrower for damage, and repair the damage before

you start and operate the snowthrower.

• DO NOT operate the equipment without wearing

adequate winter garments. Avoid loose fitting clothing

that can get caught in moving parts. Wear footwear that

will improve footing on slippery surfaces.

• DO NOT touch a hot muffler or engine. Let the muffler

and engine cylinder to cool before touching.

Operating Area

1. Identify the walkways and driveways where you plan to

operate the snowthrower.

2. Make sure that the area is free of debris or objects that

the auger could pick-up and throw from the chute.

WARNING

This machine is capable of throwing objects that could

injure bystanders or cause damage to buildings.

3. Before you start the engine, move the snowthrower

outdoors and away from windows and doors.

WARNING

Engines give off carbon monoxide, an ordorless, colorless,

poison gas. Breathing carbon monoxide can cause nausea,

fainting, or death.

• Start and operate the engine outdoors.

• Do not operatethe engine in an enclosed area, even

if doors or windows are open.

4. Make sure that the operating area is clear of bystanders,

especially children.

WARNING

This snowthrower is capable of amputating hands and feet,

and throwing objects. Read and obey the safety instructions

in this manual. Failure to do so could result in death or

serious injury.

• Keep children out of the area during operation.

• Children are often attracted to the equipment. Be

mindful of all persons present.

• Be alert and turn the unit off if bystanders enter the

area.

• Use extra care when you approach blind corners,

shrubs, tress, or other objects that can obscure vision.

Oil Recommendations

Oil Capacity:See theSpecificationssection.

NOTICE

This engine was shipped from Briggs & Stratton without oil.

Equipment manufacturers or dealers may have added oil

to the engine. Before you start the engine for the first time,

make sure to check the oil level and add oil according to the

instructions in this manual. If you start the engine without

oil, it will be damaged beyond repair and will not be covered

under warranty.

We recommend the use of Briggs & Stratton

®

Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF, SG,

SH, SJ or higher. Do not use special additives.

Outdoor temperatures determine the correct oil viscosity

for the engine. Use the chart to select the best viscosity

for the outdoor temperature range expected. Engines on

most outdoor power equipment operate well with 5W-30

Synthetic oil. For equipment operated in hot temperatures,

Vanguard

®

15W-50 Synthetic oil provides the best

protection.



A SAE 30 -Below 40 °F (4 °C) the use of SAE 30 will result in hard

starting.

B 10W-30 -Above 80 °F (27 °C) the use of 10W-30 may cause

increased oil consumption. Check oil level more frequently.

C 5W-30

D Synthetic 5W-30

Not for

Reproduction

7

E

Vanguard

®

Synthetic 15W-50

Engine

Checking Oil

NOTICE

The engine was shipped from the factory without oil. Before

you start the engine, make sure that you add oil according

to the instructions in this manual. If you start the engine

without oil, it will be damaged beyond repair and will not be

covered under the warranty.

Use Briggs & Stratton® Synthetic5W-30Warranty Certified

oil for best performance. Other high-quality detergent oils

are acceptable if classified for service SF, SG, SH, SJ or

higher. Do not use additives.

1. Put the unit on a level surface.

2. Remove unwanted material from the oil fill area.

3. Remove the oil dipstick (A,Figure3) and clean it with a

cloth.

4. Install and tighten the dipstick. Then, remove it again, and

check the oil level. Make sure that the oil level touches

the top of the full indicator (C).

5. Slowly add oil into the engine oil fill (B).Do not overfill.

6. Wait one minute, and then check the oil level.

7. When the oil level touches the top of the full indicator (C),

install and tighten the dipstick.

3

Adding Fuel

Fuel must have these requirements:

• Clean unleaded gasoline

• A minimum of 87 octane / 87 AKI (90 RON)

• Up to 10% ethanol is acceptable

NOTICE

Do not use unapproved gasolines, such as E15 and E85.

Do not mix oil in gasoline or modify the engine to run on

alternate fuels. Use of unapproved fuels will cause engine

damage that will not be covered under warranty.

At altitudes over 5,000 feet (1524 meters), a minimum 85

octane / 85 AKI (89 RON) gasoline is acceptable. To remain

emissions compliant, high altitude adjustment is required.

Operation without this adjustment will cause decreased

performance, increased fuel consumption, and increased

emissions. See an authorized service dealer for high altitude

adjustment information. Operation at altitudes below 2,500

feet (762 meters) with the high altitude adjustment is not

recommended.

Not for

Reproduction

8

WARNING

Fuel and its vapors are extremely flammable and explosive.

Always handle fuel with extreme care.

Failure to observe these safety instructions can cause a fire

or explosion which could result in serve burns or death.

• DO NOT add fuel when the engine is ON. Let the

engine cool at least 2 minutes before you add fuel.

• Fill the fuel tank outdoors only with an approved

container. Make sure that the unit is on the ground.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Let spilled fuel evaporate before you start the engine.

• If fuel is spilled on clothing, change clothing

immediately.

1. Slowly remove the fuel cap (A,Figure4) and fill the tank

(B)with fuel. DO NOT fill higher than the bottom of the

fuel tank neck (C).

2. Install the fuel cap. Let spilled fuel evaporate before you

start the engine.

4

Starting Engine

WARNING

Fuel and its vapors are extremely flammable and

explosive. Always be careful with fuel.

Failure to observe these safety instructions can cause

a fire or explosion, which could result in serve burns or

death.

• Make sure that the spark plug, muffler, fuel cap, and

air cleaner (if equipped) are in place and secured.

• Do not crank the engine with the spark plug removed.

• Do not use pressurized starting fluids because their

vapors are flammable.

• Do not over-prime the engine. Follow the engine

starting instructions in this manual.

• If the engine floods, set the choke (if equipped) to the

OPEN/RUN position, move the throttle (if equipped) to

the FAST position, and start the engine.

1. Make sure that the auger control lever (A, Figure5) and

the traction control lever(B)are disengaged.

2. Turn the fuel shut-off valve(C) (if equipped) to the OPEN

position.

3. Move the throttle control (D)(if equipped) to the FAST

position.

4. Turn the ignition key (E)to the ON position or install the

push/pull key.

5. Turn the choke control (F)to the CLOSED position.

Note:The choke is usually not needed to start a warm

engine.

6. Push the primer (G)two times.

Note:The primer is usually not needed to start a warm

engine.

Not for

Reproduction

9

5

7. For rewind start:Firmly hold the starter cord handle (H).

Pull the handle slowly until resistance is felt, then pull

rapidly.

WARNING

Rapid retraction of the starter cord (kickback) will pull your

hand and arm toward the engine faster than you can let go.

Broken bones, fractures, bruises, or sprains could result.

8. For electric start:Connect the extension cord (E,

Figure6) to the starter box (F)on the engine, and the wall

receptacle. Push the starter box push-button (G). After

the engine starts, disconnect the extension cord from the

wall receptacle and the starter box.

WARNING

Damaged or ungrounded power cords could cause electric

shock. Electric shock could cause severe burns or death.

• Use only a three-conductor power cord that is

correctly grounded to the power source.

• If the extension cord is damaged, it must be replaced

by the manufacturer or its service agent or a similarly

qualified person.

NOTICE To extend the life of the starter, use short starting

cycles (five seconds maximum). Wait one minute between

start attempts.

If the engine does not start after repeated attempts,

contact an authorized service dealer.

9. Make sure that the engine is warm. Then, gradually move

the choke control (F,Figure 5) to the OPEN position.

6

Stopping the Engine

1. Turn the ignition key (E,Figure5) to the Off position and

remove it or remove the push/pull key (if equipped).

2. Keep the key in a safe place out of the reach of children.

The engine cannot be started without the key.

Adjusting the Discharge Chute and

Deflector

WARNING

Ice, gravel, or other unintended objects can be picked up

by the auger and thrown from the chute with force. Objects

thrown from the chute could cause death, serious injury, or

property damage.

• Always be aware of the direction the snow is being

thrown.

Discharge Chute

Turn the discharge chute left or right to control the direction of

the snow discharge.

Push either side of the control switch (A, Figure7) to turn

the chute left or right. The engine must be ON to operate the

switch.

Not for

Reproduction

10

7

Deflector

The discharge deflector can be raised or lowered to control

the distance of the snow discharge. Raise the deflector to

throw the snow further. Lower the deflector to throw the snow

closer.

Push the control switch(A, Figure7)to raise or lower the

deflector.

Engaging the Auger and Impeller

The auger and impeller work together to break up the snow

as the snowthrower moves forward and throws it out the

discharge chute.

DANGER

The snowthrower contains a rotating auger and impeller that

throws snow. Fingers or feet can quickly become caught in

the rotating auger or impeller, which can result in traumatic

amputation or severe laceration.

1. Push and hold down the auger control lever (A, Figure8)

on the left handle to engage the auger and impeller.

8

2. Release the auger control lever to disengage the auger

and impeller. The auger and impeller must stop within

5 seconds after the auger control lever is released. If it

does not:

• Adjust the control cable. SeeAdjusting the Auger and

Impeller Control Cable.

• If the auger and impeller still does not stop within 5

seconds, see an authorized dealer.

Engaging the Drive Wheels

NOTICE DO NOT move the speed control lever while the

traction control lever is engaged. This can result in damage

to the drive system.

1. To drive forward, move the speed control lever

(B,Figure8) to one of the forward positions. Set a lower

number for heavy snow, a middle number for light snow,

and a higher number to transport the snowthrower.

2. Push and hold down the traction control (C)on the right

handle.

3. To stop, release the traction control lever. The unit will

stop immediately. If it does not stop:

• Adjust the control cable. SeeAdjusting the Traction

Control Cable.

• If the unit still does not stop, see an authorized

dealer.

Not for

Reproduction

11

4. To drive backward, move the speed control lever to one

of the reverse positions (R1 or R2).

5. Push and hold down the traction control lever.

6. To stop the unit, release the traction control lever. The

unit will stop immediately. If it does not:

• Adjust the control cable. SeeAdjusting the Traction

Control Cable.

• If the unit still does not stop, see an authorized

dealer.

NOTICE Do not overload the machine capacity by

removing snow at too fast of a rate.

Using the Steering Control

The Steering Control feature (Figure9) helps the operator

turn the unit. The Steering Control levers are below the hand

grips. The Steering Control temporarily disengages one drive

wheel while the other continues to drive through the turn.

9

To Turn Left:

Lift and hold the left Steering Control Lever (Figure10)

located below the left-hand grip.

Note:The Steering Control feature will be more difficult to

activate under a heavy load. Activate the lever before a turn.



10

To Turn Right:

Lift and hold the right Steering Control Lever (Figure11)

located below the right-hand grip.

11

Not for

Reproduction

12

When both Steering Control Levers (Figure12) are released,

both drive wheels are engaged and the unit will drive in a

straight line.

12

Cleaning a Clogged Discharge Chute

DANGER

The discharge chute contains a rotating impeller that

throws snow. Fingers can quickly become caught in the

impeller and result in traumatic amputation or severe

laceration. DO NOT use your hands to clean a clogged

discharge chute! Always use a clean-out tool.

1. Turn the engine OFF and remove the ignition key or

push/pull key.

2. Look to make sure that the impeller is stopped. DO NOT

use your hands.

3. Use a clean-out tool (A, Figure13) to remove snow from

the discharge chute. DO NOT use your hands to clean a

clogged discharge chute.

13

Headlight

Some models are equipped with a headlight that illuminates

the area in front of the snowthrower. When you START the

engine, the headlight turns ON. There is no switch.

Using the Heated Hand Grips

1. Turn on the grip warmer switch (A,Figure14) to activate

the heated hand grips (if equipped).

2. Before the snowthrower stops, turn off the grip warmer

switch.

14

Maintenance and Adjustments

We recommend contacting an authorized service dealer

for all maintenance, adjustments, and servicing of the unit.

Some routine maintenance tasks can be performed by the

owner. Refer to the maintenance schedule and procedures

that follow.

CAUTION

All the components used to build this product must remain

in place for correct operation. Replacement parts must be

of the same design and installed in the same position as the

original parts. Other parts may not perform as well, damage

the unit, and result in injury.

WARNING

This snowthrower must be correctly maintained to ensure

safe operation and performance. Failure to obey the safety

instructions in this manual could result in death or serious

injury.

• Before maintenance or repairs on the snowthrower,

STOP the engine and remove the ignition key or the

push/pull key.

Maintenance Schedule

First 5 Hours

Change oil

Before Each Use

• Check engine oil level

• Check auger and impeller stop time

After Each Use

Remove accumulated snow and slush to prevent freezing of the controls,

wheels, discharge chute, and auger

Every 25 Hours or Annually

Not for

Reproduction

13

• Change the engine oil

• Check tire pressure

• Check auger and traction cable adjustment

• Lubricate control lever linkages

• Lubricate the discharge chute and deflector

• Lubricate the auger assembly

• Lubricate the hex shaft and gear

• Lubricate the drive wheel axles

Every 50 Hours or Annually

• Change the engine oil

• Check muffler and spark arrester (if equipped)

Annually

• Replace spark plug (dealer service)

• Check valve clearance

Emissions Control

Maintenance, replacement, or repair of the emissions control

devices and systems must be serviced by any non-road

engine repair establishment or individual. However, to obtain

“no charge” emissions control service, the work must be

serviced by a factory authorized dealer.

Changing the Engine Oil

Discard used oil correctly. Do not discard with household

waste. Check with your local authorities, service center, or

dealer for safe disposal or recycling facilities.

Use Briggs & Stratton

®

Synthetic 5W-30 Warranty Certified

oil for best performance. Other high-quality detergent oils are

acceptable if classified for service SF, SG, SH, SJ or higher.

Do not use any additives.

1. With the engine stopped but still warm, turn the ignition

key to the OFF position, and remove it or pull out the

push/pull key (if equipped).

WARNING

Fuel and its vapors are extremely flammable, which could

cause burns or fire resulting in death or serious injury.

• Make sure that the fuel tank is empty. Fuel leakage

can result in a fire or explosion.

2. Remove the oil drain plug (D,Figure15). Carefully tilt the

snowthrower and drain the oil into a container.

Note:Move the speed control lever to position 6 for additional

clearance.

3. Install and tighten the oil drain plug.

15

4. Put the unit on a level surface.

5. Clean the oil fill area.

6. Remove the dipstick (A, Figure16) and clean it with a

cloth. Set the dipstick aside.

16

7. Slowly add oil into the engine oil fill tube (B).

SeeSpecificationsfor the oil capacity. Do not overfill.

Not for

Reproduction

14

8. Wait one minute, and check the oil level again.

9. Install and tighten the dipstick, then remove it again to

check the oil level. Make sure that the oil level touches

the top of the full indicator (C).

10. When the oil level is at the top of the full indicator, install

and tighten the dipstick.

Adjusting the Skid Shoe Height

DANGER

This snowthrower contains a rotating auger that collects

snow. Fingers can quickly become caught and can result in

a traumatic amputation or a severe laceration.

• Turn the engine OFF. Wait for all moving parts to

stop. Remove the ignition key or push/pull key before

maintenance or repairs.

WARNING

If hit by the auger or impeller, objects such as gravel, rocks,

or other unwanted material can be thrown with sufficient

force and cause personal injury, property damage, or

damage to the snowthrower.

Skid shoes are on each side of the auger housing. They can

be adjusted to increase or decrease the distance between the

scraper bar and the surface to be cleared.

Set the skid shoes at the correct height to maintain ground

clearance for the type of surface being cleared.

1. Turn the engine OFF and remove the ignition key or

push/pull key.

2. Find the scraper bar clearance needed for the surface to

be cleared.

• To remove snow from hard surface areas, adjust the

skid shoes up to lower the scraper bar closer to the

surface.

• To remove snow from gravel-covered or uneven

surfaces, adjust the skid shoes down to raise the

scraper bar further from the surface. This will help

prevent rocks and other unwanted materials from

being picked up and thrown by the auger and

impeller.

3. Put the unit on a level surface.

4. Loosen the skid shoe mounting nuts (A,Figure17) on

the skid shoe(B).

17

5. Under each end of the scraper bar (C,Figure18), put a

wooden block (A, B)of the same thickness at the desired

clearance height.

18

6. Make sure that each skid shoe firmly touches the surface.

Then tighten the mounting nuts.

NOTICE To prevent contact with the auger, make sure

that the mounting nuts are outside of the auger housing.

Lubricating the Control Lever Linkage

Apply grease to the speed selector pivot points (A, Figure19).

Not for

Reproduction

15

19

Lubricating the Discharge Chute,

Deflector, and Wheel Axle

1. Turn the engine OFF and remove the ignition key or

push/pull key.

2. Apply a light film of lithium grease to the rotation gear (A,

Figure20) at the base of the discharge chute.

3. Apply a drop of clean engine oil to the pivot points (B)of

the chute deflector.

4. Lubricate both wheel axles (C)with lithium grease.

20

Lubricating the Auger Assembly

1. Turn the engine OFF and remove the ignition key or

push/pull key.

2. Lubricate the auger shaft assembly (A, Figure21) with

grease at the grease fittings (if equipped).

21

Lubricating the Hex Shaft and Gear

For friction drive systems only:

NOTICE Do not let grease or oil touch the rubber friction

wheel or the disc drive plate. If grease or oil touches the

friction wheel, replace it. Do not attempt to clean it. If grease

or oil touches the disc drive plate, clean it thoroughly with

an alcohol based solvent.

1. Turn the engine OFF and remove the ignition key or

push/pull key.

2. Set the speed select lever to the first forward gear.

WARNING

Fuel and its vapors are extremely flammable, which could

cause burns or fire that result in death or serious injury.

• When performing maintenance that requires the unit to

be tipped, the fuel tank must be empty or fuel can leak

out and result in a fire or explosion.

3. Stand the snowthrower up on the auger housing end.

Note:When the crankcase is filled with oil, do not leave

the snowthrower standing up on the auger housing for an

extended period of time.

4. Remove the screws (A,Figure22) and bottom panel (B).

5. Put a small amount of 50 weight synthetic motor oil on

a piece of cloth.Then, use the cloth to apply a very thin

coat of oil to the hex shaft (C,Figure23). Do this before

storage and at the start of each season.

NOTICE Do not let grease or oil touch the rubber friction

wheel or the disc drive plate. If grease or oil touches the

friction wheel, replace it. Do not attempt to clean it. If grease

or oil touches the disc drive plate, clean it thoroughly with

an alcohol based solvent.

6. Lightly, lubricate the sprocket (D)and chain (E)with

motor oil, before storage and at the start of each season.

Not for

Reproduction

16

22



23

Replacing the Shear Pins or Shear Bolts

DANGER

The snowthrower contains a rotating auger and impeller

that throws snow. Fingers or feet can quickly become

caught in the rotating auger or impeller resulting in traumatic

amputation or severe laceration.

• Turn the engine OFF, wait for all moving parts to stop,

and remove the ignition key or push/pull key before

maintenance or repairs.

The augers are secured to the gear box axle with either

shear pins, shear bolts, or shear bolts with spacers. These

shear pins or bolts are designed to break if an object

becomes lodged in the auger housing. Shear pins are

installed with cotter pins. Shear bolts and shear bolts with

spacers are installed with nuts. The three hardware systems

arenotinterchangeable.

1. Turn the engine OFF. Remove the ignition key or push/

pull key.

2. Remove the remaining pieces of the hardware from the

auger shaft and discard.

3. Use a grease gun, and apply lithium grease to the grease

fitting (if equipped) on the auger shaft. Rotate the auger

to distribute the grease.

4. Align the auger holes and axle holes and install:

• a new shear pin (A,Figure24) through the auger hole

(C)and secure with a cotter pin (B).

24

• a new shear bolt(A,Figure25) through the auger

hole(B)and secure with the locknut (C).

25

• a new shear bolt (A, Figure26) and space (B),

through the auger hole (C)and secure with the

locknut(D).

Not for

Reproduction

17

26

Adjusting the Auger and Traction Cable

DANGER

The snowthrower contains a rotating auger and impeller

to throw snow. Fingers or feet can quickly become caught

in the rotating auger or impeller resulting in traumatic

amputation or severe laceration.

• Over-tightening the auger cable can cause the auger

to rotate even if the auger control lever is not pushed

down.

• Turn the engine OFF, wait for all moving parts to stop,

and remove the ignition key or push/pull key before

maintenance or repairs.

1. Turn the engine OFF and remove the ignition key or

push/pull key.

2. Use a wrench to hold stationary the adjuster tube (A,

Figure27). Use another wrench to loosen the jam nut

(B).

3. Turn the adjuster tube clockwise or counterclockwise to

get a 0.060" (1.5 mm) clearance between the spring (C)

and the cable loop (D). 

4. Use a wrench to hold stationary the adjuster tube. Use

another wrench to tighten the jam nut.

5. Check the clearance between the spring and the cable

loop. If the clearance changed, repeat steps 2 through

5 until you get a 0.60" (1.5 mm) clearance between the

spring and the cable loop.

27

6. Check the operation of the auger and impeller control

using the test below.



Test 1 - Auger/Impeller Control

With the engine running:

• Push down on the auger control lever. The auger/

impeller should rotate.

• Release the auger control lever. The auger/impeller

must stop within 5 seconds.

Test 2 - Traction Drive Control

With the engine running and speed control lever in 1st

gear:

• Push down on the traction control lever. The unit

should move forward.

• Release the traction lever. The unit must stop.

Test 3 - Free Hand Feature

With the engine running:

• Engage the auger and traction control levers, then

release the auger control lever. Both controls should

remain engaged.

• Next, release the traction control lever. Both controls

must release.

Not for

Reproduction

18

7. If the unit does not operate as described, DO NOT use

it. Contact an authorized service dealer to have the unit

inspected and adjusted or repaired.

Speed Control Rod Adjustment

If the speed control rod requires adjustment, see an

Authorized Service Dealer.

Adjusting the Steering Control Cable

DANGER

The snowthrower contains an auger and impeller that

throws snow. Fingers or feet can quickly become caught in

the auger or impeller that can result in traumatic amputation

or severe laceration.

• Turn the engine OFF. Wait for all moving parts to stop,

and remove the ignition key or push/pull key before

maintenance or repairs.

The steering control cable can stretch slightly after repeated

usage during the first season of operation. If the cable has

stretched, it can prevent the drive gears from disengaging

while the control activates.

1. Turn the engine OFF and remove the ignition key or

push/pull key.

2. With both steering control levers released, rock the unit

back and forth so that both wheels are engaged (not free-

wheeling).

3. Lift the adjuster cover (A, Figure28) up and away from

the adjuster.

4. Use a wrench to hold stationary the adjuster tube (B).

Use another wrench to loosen the jam nut.

5. Push the steering control lever down until it stops.

6. Turn the adjuster clockwise or counterclockwise to get

a small amount of play in the lever before the steering

control operates.

7. Use a wrench to hold stationary the adjuster tube. Use

another wrench to tighten the jam nut.

8. Lower the adjuster cover onto the adjuster.

9. Do the same procedure for the other steering control

cable.

10. Test 1 - Left Side Steering Control

Lift and hold the left steering control lever. The wheel

should roll freely

11. Test 2 - Right Side Steering Control

Lift and hold the right steering control lever. The wheel

should roll freely



28

Replacing the Scraper Bar

DANGER

The snowthrower contains a rotating auger and impeller

that throws snow. Fingers or feet can quickly become

caught in the rotating auger or impeller resulting in traumatic

amputation or severe laceration.

• Turn the engine OFF, wait for all moving parts to stop,

and remove the ignition key or push/pull key before

maintenance or repairs.

After some time, the scraper bar will gradually wear and need

replacement.

1. Turn the engine OFF and remove the ignition key or

push/pull key.

2. Loosen the retaining nuts (A,Figure29) and bolts (B)and

remove the scraper bar (C).

3. Align the holes in the new scraper bar with the holes on

the auger housing.

4. Install the retaining nuts and bolts, and tighten them.

5. Check the clearance between the scraper bar and the

surface.

6. Adjust the skid shoes, if necessary, to maintain ground

clearance for the type of surface being cleared.

SeeAdjusting the Skid Shoe Height.

Not for

Reproduction

19

29

Checking Tire Pressure

Tire pressure should be checked periodically. Recommended

tire pressure varies by tire manufacturer. A good rule of

thumb is to inflate the tire up to, but not exceeding, the “Max

Inflation” stamped on the sidewall of the tire.

Storage

Storage - Fuel System

Fuel can become stale when kept in a storage container

for more than 30 days. Each time you fill the container with

fuel, addSTA-BIL 360°

®

PROTECTION™fuel stabilizerto

the fuel as specified by the manufacturer’s instructions. This

keeps fuel fresh and decreases fuel-related problems or

contamination in the fuel system.

It is not necessary to drain fuel from the engine whenSTA-

BIL 360°

®

PROTECTION™fuel stabilizeris added as

instructed. Before storage, turn the engine ON for 2 minutes

to move the fuel and stabilizer through the fuel system.

Off-Season Storage

At the end of the season, or when the unit is in storage for

more than 30 days, complete the steps that follow.

WARNING

Gasoline is highly flammable and its vapors are explosive.

Fumes can travel to a distant ignition source and an

explosion and/or fire can result.

• If fuel is in the tank, do not store the unit indoors or

in poorly ventilated areas where fumes could reach

sparks, open flames, pilot lights, heat, and other ignition

sources.

Snowthrower

• Clean the unit. Make sure that all nuts, bolts, and screws

are connected.

• Examine visible moving parts for damage, breakage,

and wear. Replace if necessary.

• Lubricate the control lever linkages, chute and

deflector, auger assembly, and drive wheel axles.

SeeMaintenance and Adjustments.

• For rusted or chipped paint surfaces, sand lightly and

apply touch-up paint.

• For unpainted or bare metal surfaces, apply a rust

preventative product.

• Keep the unit indoors and cover it. If kept outdoors,

cover it with a heavy tarpaulin.

Returning the unit to Service

• Have an authorized service dealer perform annual

maintenance tasks. SeeMaintenance Schedule.

• Inspect engine oil level and add oil, if necessary.

• Fill the fuel tank with clean fuel.

• Check tire pressures.

• Make sure that all guards, shields, and covers are

attached.

• Make sure that all fasteners are tightened.

• Inspect the auger and impeller control, and the traction

drive control.

Troubleshooting Chart

Problem Look for Remedy

The key is not installed or set to the OFF position. Install the key or turn it to the ON position.

The engine is cold and requires priming. Push the primer button two times and start the

engine again.

The fuel shut-off valve (if equipped) is in the

CLOSED position.

Turn fuel shut-off valve to the OPEN position.

The fuel tank is empty. Fill fuel tank with clean fuel.

The choke is turned to the OPEN/RUN position

with cold engine.

Turn the choke to the CLOSED/START position.

The engine does not start.

The engine is flooded. Turn the choke to OPEN/RUN position, move

throttle control to the FAST position (if equipped),

and crank until the engine starts.

Stale fuel or moisture in fuel. Fill with clean fuel.The engine is hard to start, runs poorly, or does not

operate after several minutes.

The fuel cap does not vent. The fuel cap is too tight. Remove the fuel cap, and

install it again. Do not overtighten.

Excessive vibration. Loose parts or damaged impeller. Stop the engine immediately. Remove the ignition

key or push/pull key. Inspect for loose hardware

on any moving parts and tighten as necessary.

If vibration continues, make sure that the unit is

inspected by an authorized service dealer.

Not for

Reproduction

20

Problem Look for Remedy

The auger does not stop within 5 seconds after

auger control lever is released.

The auger control cable is not adjusted correctly. SeeAdjusting the Auger Cable.

The discharge chute or deflector in not adjusted

correctly.

Adjust the control linkage and pivot points.

SeeAdjusting the Discharge ChuteorAdjusting

the Deflector.

The discharge chute or deflector does not work

(remote-manual).

The discharge chute or deflector needs lubrication. Lubricate the control linkage and pivot points.

SeeLubricating the Control Lever Linkage.

The snowthrower does not stop when the traction

control is released.

The traction control cable is not adjusted correctly. SeeAdjusting the Traction Control Cable.

The kid shoes are not correctly adjusted. Raise or lower the skid shoes. SeeAdjusting the

Skid Shoe Height.

The scraper bar does not clean hard surfaces.

Worn scraper bar. Replace the scraper bar. SeeReplacing the

Scraper Bar.

The unit does not propel itself. Incorrect adjustment of traction control cable. SeeAdjusting the Traction Control Cable.

The auger control cable out of adjustment. Adjust auger control cable. SeeAdjusting the

Auger Cable.

Broken shear pin or shear bolt. Replace shear pin or bolt. SeeReplacing the Shear

Pins or Shear Bolts.

The discharge chute is clogged. STOP THE ENGINE! Make sure that the auger and

impeller have stopped rotating. Use a clean-out

tool to remove the snow from the discharge chute.

DO NOT clear a clogged discharge chute with your

hands! SeeClearing a Clogged Discharge Chute.

The unit does not discharge snow.

Unwanted debris is lodged in auger. STOP THE ENGINE! Make sure that the auger and

impeller DO NOT rotate. Use a clean-out tool to

remove the foreign object. DO NOT clear a lodged

object with your hands! SeeClearing a Clogged

Discharge Chute.

For all other issues, contact an authorized service dealer.

Specifications

Specification Chart

The spark ignition system on this snowthrower complies with Canadian standard ICES-002.

Item Model 100000 Model 120000 Model 130000 Model 150000 Model 19J000 Model 250000

Armature air gap .010 - .014 inch

(,25 - ,36 mm)

.010 - .014 inch

(,25 - ,36 mm)

.010 - .014 inch

(,25 - ,36 mm)

.010 - .014 inch

(,25 - ,36 mm)

.008 - .016 inch

(,2 - ,4 mm)

.008 - .016 inch

(,2 - ,4 mm)

Intake Valve

Clearance

.004 - .006 inch

(,10 - ,15 mm)

.004 - .006 inch

(,10 - ,15 mm)

.004 - .006 inch

(,10 - ,15 mm)

.004 - .006 inch

(,10 - ,15 mm)

.005 - .007 inch

(,13 - ,18 mm)

.005 - .007 inch

(,13 - ,18 mm)

Exhaust Valve

Clearance

.006 - .008 inch

(,15 - ,20 mm)

.009 - .011 inch

(,23 - ,28 mm)

.006 - .008 inch

(,15 - ,20 mm)

.009 - .011 inch

(,23 - ,28 mm)

.005 - .007 inch

(,13 - ,18 mm)

.005 - .007 inch

(,13 - ,18 mm)

Oil Capacity 18 - 20 oz

(,54 - ,59 L)

18 - 20 oz

(,54 - ,59 L)

18 - 20 oz

(,54 - ,59 L)

18 - 20 oz

(,54 - ,59 L)

36 - 38 oz

(1,0 - 1,1 L)

36 - 38 oz

(1,0 - 1,1 L)

Sparkplug gap .030 inch

(,76 mm)

.030 inch

(,76 mm)

.030 inch

(,76 mm)

.030 inch

(,76 mm)

.030 inch

(,76 mm)

.030 inch

(,76 mm)

Engine power will decrease 3.5% for every 1,000 feet (300 meters) above sea level and 1% for every 10 degrees F (5.6 degrees C) above 77 Degrees F

(25 Degrees C). The engine will operate satisfactorily at an angle up to 15 degrees.

Power Ratings

The gross power rating for individual gasoline engine models is labeled in accordance with SAE (Society of Automotive

Engineers) code J1940 Small Engine Power & Torque Rating Procedure, and is rated in accordance with SAE J1995. Torque

values are derived at 2600 RPM for those engines with “rpm” called out on the label and 3060 RPM for all others; horsepower

values are derived at 3600 RPM. The gross power curves can be viewed at www.BRIGGSandSTRATTON.COM. Net power

values are taken with exhaust and air cleaner installed whereas gross power values are collected without these attachments.

Actual gross engine power will be higher than net engine power and is affected by, among other things, ambient operating

conditions and engine-to-engine variability. Given the wide array of products on which engines are placed, the gasoline engine

may not develop the rated gross power when used in a given piece of power equipment. This difference is due to a variety

of factors including, but not limited to, the variety of engine components (air cleaner, exhaust, charging, cooling, carburetor,

La page est en cours de chargement...

Simplicity 1696920-00 Manuel utilisateur

Ce manuel convient également à

Simplicity 1696920-00 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents