MQ Multiquip MC3-SERIES-Briggs-Electric Mode d'emploi

Marque: MQ Multiquip

Modèle: MC3-SERIES-Briggs-Electric

Taper: Mode d'emploi

OPERATION AND PARTS MANUAL

THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.

Revision #6 (04/15/21)

To ﬁnd the latest revision of this

publication, visit our website at:

www.multiquip.com

MIX N' GO

MODELS MC3SE, MC3S (B&S)

MINI CONCRETE STEEL DRUM MIXERS

MODELS MC3PE, MC3P (B&S)

MINI CONCRETE PLASTIC DRUM MIXERS

Engine exhaust and some of

its constituents, and some dust created

of California to cause cancer, birth

defects and other reproductive harm.

by power sanding, sawing, grinding,

drillingandotherconstructionactivities

contains chemicals known to the State

Some examples of these chemicals are:

Leadfromlead-basedpaints.

Crystallinesilicafrombricks.

Cementandothermasonryproducts.

Arsenicandchromiumfromchemically

treatedlumber.

Your risk from these exposures varies,

dependingonhowoftenyoudothistype

of work. To reduce your exposure to

these chemicals: work in aALWAYS

well ventilated area, and work with

approved safety equipment, such as

dust masks that are specially designed

to filter out microscopic particles.

PROPOSITION 65 WARNING

MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #5 (11/07/05) — PAGE 3

Grinding/cutting/drilling of masonry, concrete, metal and

other materials with silica in their composition may give

off dust or mists containing crystalline silica. Silica is a

basic component of sand, quartz, brick clay, granite and

numerous other minerals and rocks. Repeated and/or

substantial inhalation of airborne crystalline silica can

cause serious or fatal respiratory diseases, including

silicosis. In addition, California and some other

authorities have listed respirable crystalline silica as a

substance known to cause cancer. When cutting such

materials, always follow the respiratory precautions

mentioned above.

WARNING

Grinding/cutting/drilling of masonry, concrete, metal and

other materials can generate dust, mists and fumes

containing chemicals known to cause serious or fatal

injury or illness, such as respiratory disease, cancer,

birth defects or other reproductive harm. If you are

unfamiliar with the risks associated with the particular

process and/or material being cut or the composition of

the tool being used, review the material safety data

sheet and/or consult your employer, the material

manufacturer/supplier, governmental agencies such as

OSHA and NIOSH and other sources on hazardous

materials. California and some other authorities, for

instance, have published lists of substances known to

cause cancer, reproductive toxicity, or other harmful

effects.

Control dust, mist and fumes at the source where

possible. In this regard use good work practices and

follow the recommendations of the manufacturers or

suppliers, OSHA/NIOSH, and occupational and trade

associations. Water should be used for dust

suppression when wet cutting is feasible. When the

hazards from inhalation of dust, mists and fumes cannot

be eliminated, the operator and any bystanders should

always wear a respirator approved by NIOSH/MSHA for

the materials being used.

WARNING

SILICOSIS WARNING RESPIRATORY HAZARDS

SILICOSIS/RESPIRATOR WARNINGS

PAGE 4 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21)

TABLE OF CONTENTS

Multiquip Mix N' Go —

Portable Concrete Mixer

Proposition 65 Warning ............................................. 2

Silicosis/Respiratory Warnings .................................. 3

Table of Contents ...................................................... 4

Safety Message Alert Symbols .............................. 6-7

Rules For Safe Operation .................................... 8-10

Operation and Safety Decals ............................. 11-12

Specifications .......................................................... 13

Dimensions (Mixer) ................................................. 14

Dimensions (Electric Motor) .................................... 15

General Information ................................................ 16

Mixer Components .................................................. 17

Basic Engine ........................................................... 18

Assembly Instructions ........................................ 19-20

Pre-Inspection (Gasoline Engine) ........................... 21

Initial Start-up (Electric Motor) ................................ 22

Initial Start-up (Gasoline Engine)....................... 23-24

Maintenance ...................................................... 25-27

Preparation for Long-Term Storage ........................ 28

Troubleshooting (Engine) ........................................ 30

Troubleshooting (Engine/Mixer) .............................. 31

Explanation Of Code In Remarks Column .............. 32

Suggested Spare Parts ........................................... 33

Nameplate and Decals....................................... 34-35

Mixer Assembly (Steel Drum) ............................ 36-37

Mixer Assembly (Plastic Drum) .......................... 38-39

Specification and part number are subject to

change without notice.

NOTICE

MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21) — PAGE 5

NOTE S

PAGE 6 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21)

Accidental Starting

ALWAYS place the circuit breaker or power

ON/OFF switch in the OFF position when the

pump is not in use.

Respiratory Hazard

ALWAYS wear approved respiratory

protection.

Equipment Damage Messages

Other important messages are provided throughout this manual

to help prevent damage to your pump, other property, or the

surrounding environment.

ALWAYS wear approved eye and hearing

protection.

Sight and Hearing hazard

MIX N' GO MIXER — SAFETY MESSAGE ALERT SYMBOLS

Safety precautions should be followed at all times when

operating this equipment. Failure to read and understand the

Safety Messages and Operating Instructions could result in

injury to yourself and others.

FOR YOUR SAFETY AND THE SAFETY OF OTHERS!

SAFETY MESSAGE ALERT SYMBOLS

The three (3) Safety Messages shown below will inform you

about potential hazards that could injure you or others. The

Safety Messages specifically address the level of exposure to

the operator, and are preceded by one of three words: DANGER,

WARNING, or CAUTION.

DANGER: You WILL be KILLED or

SERIOUSLY injured if you do not follow

directions.

WARNING: You CAN be KILLED or

SERIOUSLY injured if you do not follow

directions.

CAUTION: You CAN be injured if you

do not follow directions.

HAZARD SYMBOLS

Potential hazards associated with the MIX N' GO MIXER

operation will be referenced with Hazard Symbols which appear

throughout this manual, and will be referenced in conjunction

with Safety Message Alert Symbols.

Rotating Parts

NEVER operate equipment with covers, or

guards removed. Keep fingers, hands, hair and

clothing away from all moving parts to prevent

injury.

This Owner's Manual has been developed to provide

complete instructions for the safe and efficient operation

of the Multiquip

Model MC3 Series Portable Concrete

Mixers.

Before using these mixers, ensure that the operating

individual has read and understands all instructions

in this manual.

NOTICE

MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21) — PAGE 7

MIX N' GO MIXER — SAFETY MESSAGE ALERT SYMBOLS

Accidental Starting

ALWAYS place the engine ON/OFF switch in

the OFF position, and remove the ignition key

when the machine is not in use.

Respiratory Hazard

ALWAYS wear approved respiratory

protection.

Equipment Damage Messages

Other important messages are provided throughout this manual

to help prevent damage to your mixer, other property, or the

surrounding environment.

ALWAYS wear approved eye and hearing

protection.

Sight and Hearing hazard

This mixer, other property, or the surrounding environment

could be damaged if you do not follow instructions.

NOTICE

PAGE 8 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21)

RULES FOR SAFE OPERATION

■

ALWAYS refuel in a well-ventilated area, away from sparks

and open flames.

■

ALWAYS use extreme caution when working with flammable

liquids. When refueling, stop the engine and allow it to cool.

DO NOT

smoke around or near the machine. Fire or explosion

could result from fuel vapors, or if fuel is spilled on a hot

engine.

■

NEVER operate the mixer in an explosive

atmosphere or near combustible

materials. An explosion or fire could result

causing severe

bodily harm or even

death.

■

Topping-off to filler port is dangerous, as it tends to spill fuel.

■

Refer to the

Engine Owner's Manual

for engine technical

questions or information.

■

NEVER use accessories or attachments, which are not

recommended by Multiquip for this equipment. Damage to

the equipment and/or injury to user may result.

■

Manufacturer does not assume responsibility for any accident

due to equipment modifications.

■

NEVER touch the hot exhaust manifold,

muffler or cylinder. Allow these parts to

cool before servicing engine or mixer.

■

The engine of this mixer requires an adequate free flow of

cooling air.

NEVER!

operate the mixer in any enclosed or

narrow area where free flow of the air is restricted. If the air

flow is restricted it will cause

serious damage to the

mixer or engine and may

cause injury to people and

property. Remember the

mixer's engine (gasoline

models only) gives off

DEADLY gases.

■

High Temperatures – Allow the engine to cool before adding

fuel or performing service and maintenance functions. Contact

with

hot

components can cause serious burns.

DANGER:

Failure to follow instructions in this manual may

lead to serious injury or even death! This

equipment is to be operated by trained and

qualified personnel only! This equipment is for

industrial use only.

The following safety guidelines should always be used when

operating the Mix N' Go Mixer:

GENERAL SAFETY

■

DO NOT operate or service this equipment before

reading this entire manual.

■

This equipment should not be operated by

persons under 18 years of age.

■

NEVER operate this equipment without proper

protective clothing, shatterproof glasses, steel-

toed boots and other protective devices required

by the job.

■

NEVER operate this equipment when not feeling

well due to fatigue, illness or taking medicine.

■

NEVER operate this equipment under the

influence or drugs or alcohol.

■

Whenever necessary, replace nameplate, operation and

safety decals when they become difficult read.

■

ALWAYS check the machine for loosened threads or bolts

before starting.

■

ALWAYS wear proper respiratory (mask) hearing and eye

protection equipment when operating the mixer.

MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21) — PAGE 9

■

High Temperatures – Always stop engine and allow the

engine to cool before adding fuel, oil or performing service

and maintenance functions. Contact with

hot

components can

cause serious burns.

■

NEVER disconnect any

"emergency or safety devices"

These devices are intended for operator safety. Disconnection

of these devices can cause severe injury, bodily harm or even

death! Disconnection of any of these devices will void all

warranties.

■

If mixer is equipped with an electric motor, operate

only

120 VAC, 60 Hz.

■

Make sure the

OFF/ON

power switch is always in the

OFF

position before inserting the mixer's power plug into an AC

receptacle (electric model only).

Maintenance Safety

■

NEVER lubricate components or attempt service on a running

machine.

■

ALWAYS allow the machine a proper amount of time to cool

before servicing.

■

Keep the machinery in proper running condition.

■

Fix damage to the machine immediately and always replace

broken parts, or missing decals.

■

Dispose of hazardous waste properly. Examples of potentially

hazardous waste are used motor oil, fuel and fuel filters.

■

DO NOT use food or plastic containers to dispose of

hazardous waste.

■

DO NOT pour waste, oil or fuel directly onto the ground,

down a drain or into any water source.

RULES FOR SAFE OPERATION

■

NEVER Run engine without air cleaner. Severe engine

damage may occur.

■

ALWAYS read, understand, and follow procedures in

Operator’s Manual before attempting to operate equipment.

■

ALWAYS be sure the operator is familiar with proper safety

precautions and operations techniques before using roller.

■

ALWAYS store equipment properly when it is not being used.

Equipment should be stored in a clean, dry location out of the

reach of children.

■

NEVER leave the mixer unattended, turn off engine or electric

motor when unattended.

■

CAUTION must always be observed while servicing this mixer.

Rotating parts can cause injury if contacted.

■

Unauthorized equipment modifications will void all

warranties.

■

Ensure that any trailing cable is protected against damage

and not liable to be tripped over or trapped underneath the

mixer.

■

Ensure any extention cables must be no longer than 30 meters

(100 feet) in length and that the wire section is 2.5 mm

■

DO NOT allow extension cord to come into contact with water

or fluids.

■

DO NOT spray water onto electric motor.

■

DO NOT expose power tools to

rain

wet

conditions.

■

This mixer is intended for the production of concrete, mortar

and plaster. Mixer must be used only for its intended purpose.

■

This mixer is not suitable for the mixing of

flammable

explosive

substances.

■

NEVER operate the mixer in an

explosive

atmosphere.

■

Before starting the mixer, check that all

guards

are in position

and correctly fitted.

■

DO NOT tip mixer onto drum mouth when the motor is running.

■

Keep area around the mixer

clear of obstructions

which

could cause persons to fall onto

moving parts

■

ALWAYS ensure mixer is on level ground before mixing.

■

Become familiar with the controls of the machine before

operating.

■

ALWAYS replace any worn or damaged warning decals.

■

Ensure the drum is

rotating

while filling and emptying the

drum.

■

ALWAYS disconnect AC power plug from power source

before moving mixer (electric model only).

PAGE 10 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21)

Emergencies

■

ALWAYS know the location of the nearest

fire extinguisher

■

ALWAYS know the location of the nearest

first aid kit

■

In emergencies

always

know the location of the

nearest phone or

keep a phone on the job site

Also know the phone numbers of the nearest

ambulance

doctor

and

fire department

. This

information will be invaluable in the case of an

emergency.

RULES FOR SAFE OPERATION

MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21) — PAGE 11

OPERATION AND SAFETY DECALS

Machine Safety Decals

The Mix N' Go mixer is equipped with a number of safety decals. These decals are provided for operator safety and maintenance

information. The illustration below and on the next page shows these decals as they appear on the machine. Should any of these

decals become unreadable, replacements can be obtained from your dealer.

WARNING!

ALARMA!

AVERTISSEMENT!

ENGLISH - WARNING! TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND INSTRUCTION MANUAL

ESPAÑOL - ATENCION! PARA REDUCIR EL RIESGO DEL LESIONES EL USUARIO DEBE LEER Y ENTENDER EL MANUAL DE INSTRUCCIONES

FRANÇAIS - ATTENTION! AFIN DE DIMINUER LE RISQUE DE BLESSURES L’UTILISATEUR DOIT LIRE ET COMPRENDRE CE MANUEL D’ INSTRUCTIONS

DCL251

P/N: DCL251

P/N: 510165

PAGE 12 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21)

OPERATION AND SAFETY DECALS

6. check V-belt before starting mixer.ALWAYS

1. Read owner’s manual before operating mixer.

ELECTRIC MOTOR

Make sure power cord has been disconnected from power

source before cleaning mixer.

use an extension cord of proper size, see chart

below:

ALWAYS

50 feet

(15.24 meters)

No. 12 Wire

No. 10 Wire

No. 8 Wire

No. 6 Wire

100 feet

(30.48 meters)

75 feet

(22.86 meters)

200 feet

(60.96 meters)

EXTENSION CORD SIZE

This electric motor is for .115 VAC operation only

GASOLINE ENGINE

Make sure engine is turned off and spark plug wire is

disconnected before cleaning mixer.

operate mixer in an enclosed area, proper

ventilation is required.

DO NOT

stop the engine and allow engine to cool before

adding fuel or oil.

ALWAYS

check fuel, oil and air filter before starting engine.ALWAYS

MOTEUR ÉLECTRIQUE

Assures vous toujours que le cable a été débranché de la prise de

courant avant de nettoyer le malaxeur.

Il faut toujours utiliser une rallonge de taille appropriée, veuillez s’il vous

référer au diagramme suivant:

Ce moteur électrique à été conçu pour opération à 115 volts seulement.

MOTEUR À ESSENCE

Assurez vous que le moteur est arrêté et que le fil de la bougie est

débranché avant de nettoyer le malaxeur.

pas le malaxeur dans un endroit fermé, il est nécessaire

de travailler dans un endroit avec une bonne aération.

N’ UTILISEZ

toujours vé la courroie avant de mettre le malaxeur en

marche.

VEUILLEZ

toujours le niveau d’essence et d’huile ainsi que le filtre à

air avant de mettre le moteur en marche.

VÉRIFIEZ

REMOVE BOLT AND FILL

WITH EP. 90 GEAR OIL

ELECTRIC

MOTOR

CHECK DAILY

NEVER! OPERATE MIXER WITH

V-BELT COVER REMOVED.

MOTOR

ELÉCTRICO

MOTEUR

ÉLECTRIQUE

REVISAR DIARIO

ÔTEZ LE BOULON ET

REMPLISSEZ AVEC DE I’HUILE

EP. 90 À ENGRENAGES

2. Keep unauthorized and untrained people away

from mixer during operation.

3. Make sure all safety devices (guards) are in place

before mixer is started.

4. Keep hands and fingers away from moving objects.

5. leave mixer unattended when operating.NEVER

6. inspeccione la banda antes de encender la mezcladora.SIEMPRE

1. Lea el manual de operació antes de usar la mezcladora.

2. Mantenga personas que no estén autorizadas o capacitadas

alejades de la mezcladora durante el funcionamiento de la

máquina.

3. Asegúreseque todos los aparatos de seguridad estén

trabajando apropiadamente antes de usar la mezcladora.

4. Mantenga las monos y dedos alejados de objetos en moviminto.

5. se aleje de la mezclaora mientras ésta, este trabajando!NUNCA

6. toujours vérifier la courroie avant de mettre le malaxeur

en marche.

VEUILLEZ

1. Lisez le manual d’ utilisation avant d’ utiliser le le malaxeur.

2. Seul un personnel qualifié peut être authorisé à se trouver à proximité

du malaxeur quand il est en opération.

3. Assurez vous que tous les dispositifs de sécurité sont en place avant

de mettre le malaxeur en marche.

4. Gardez les mains et doigts loin de toute piè en mouvement.

5. jamais le malaxeur sans surveillance quand il est en

opération.

NE LAISSEZ

WARNING! ADVERTENCIA! AVERTISSEMENT!

NUNCA! MANEJE LA MEZCLADORA

SIN LA COBERTURA DE BANDA-V

REMOVIDA.

N’ UTILISEZ! JAMAIS LE MALAXEUR

SANS LE COUVERCLE DE LA COURROIE.

DCL250

MOTOR ELÉCTRICO

Asegúrese que el cable de corriente esté de empezar a limpiar

la mezcladora.

use el tamaño de extensiones de alambre indicado

como muestra el diagrama abajo:

SIEMPRE

Este motor elétrico está

de .

solamente capacitado para corriente

alterna 115 voltios

MÁQUINAS DE GASOLINA

Asegure que la máquina este apagada y el alambre de la bujía

este desconectado antes de empezar a limpiar la mezcladora.

encienda la mezcladora en una área cerrada; es necesario

estar en una área que tenga apropiada ventilación.

apague la máquina y permita que se enfrie antes de

ponerle gasolina o aceite.

SIEMPRE

revise la gasolina, aceite, y el filtro del air antes de

encender la máquina.

SIEMPRE

50 pieds

(15.24 métres)

Cable

Numéro 12

TAILLE DE LA RALLONGE

Cable

Numéro 10

Cable

Numéro 8

Cable

Numéro 6

50 pieds

(15.24 métres)

50 pieds

(15.24 métres)

50 pieds

(15.24 métres)

50 pies

(15.24 metros)

Alambre

Numéro 12

100 pies

(30.48 metros)

75 pies

(22.86 metros)

200 pies

(60.96 metros)

TAMAÑO DE EXTENSIÓN

Alambre

Numéro 10

Alambre

Numéro 8

Alambre

Numéro 6

VÉRIFIEZ QUOTIDIENNEMENT

ELECTRIC

MOTOR

ELÉCTRICO

MOTEUR

ÉLECTRIQUE

REMOVER EL TORÑILLO Y

LLENAR CON ACEITE DE

ENGRNAJE EP. 90

P/N DCL250

MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21) — PAGE 13

MIX N' GO MIXER — SPECIFICATIONS

snoitacificepSrexiMoG'NxiM.2elbaT

thgieH )mm6.368(.ni43

htdiW )mm2.485(.ni8/5-32

htgneL )mm2.912,1(.ni2/1-84

thgieWdnatS )gK9.51(.sbl53

yticapa

CmurDmumixaM m31.0(.tf.uc5.4

)

)gab2/1(yticapaCgnixiMmumixaM m80.0(.tf.uc0.3

)

rotoMcirtcelE-thgieWnedalnU )gK5.85(.sbl921

enignEenilosaG-thgieWnedalnU )gK6.26(.sbl831

)rotoMcirtcelE&enignE(snoitacificepS.1elbaT

rotoMcirtcelE/enignE

ledoM00219NOTTARTS&SGGIRB403EYL71RODLAB

epyT

elgniS,evlavlacitreV,ekorts-4

rednilyC

elg

niS,CAV021,PH4/3

rotoMcirtcelEesahP

ekortSXeroB

.ni57.1x.ni65.2

)mm4.44xmm1.56(

A/N

tnemecalpsiD)cc841(.ni.u

c0.9A/N

tuptuOxaM.M.P.R006,3taPH5.3MPR054,3/.P.H4/3

deepSeldIdradnatS.M.P.R001±008,1A/N

yticapaCknaTleuF

snoll

aG.S.U5.0.xorppA

)sretiL98.1(

A/N

leuFenilosaGdedaelnUA/N

yticapaCliOebuL)sretiL98.1(strauQ.S.U2A/N

dohteMlort

noCdeepSepyTthgiew-ylFlagufirtneCA/N

dohteMgnitratStratSlioceRA/N

)HxWxL(snoisnemiD

.ni81.21x74.11x5.21

)mm4.

903x4.192x5.713(

.ni0.8X0.6x57.11

)mm302X251X892(

thgieWteNyrD

)gk2.9(sbl3.02).gK4.5(.sbl21.xorppA

PAGE 14 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21)

MIX N' GO MIXER — DIMENSIONS (MIXER)

Figure 1. Mix N' Go

Mixer Dimensions

MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21) — PAGE 15

MIX N' GO MIXER — DIMENSIONS (ELECTRIC MOTOR)

Figure 2. Electric Motor

PAGE 16 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21)

MIX N' GO MIXER — GENERAL INFORMATION

APPLICATION

This mixer is

only

intended for the production of

concrete

and

mortar

. The mixer must be used for its intended

purposes and is not suitable for the mixing of

flammable

explosive

substances. The mixer must not be used in an

explosive atmosphere.

POWER PLANTS

This portable mixer is powered by either a Briggs and Stratton

4-stroke, verticle valve, single cylinder, gasoline engine rated

at 3.5 hp @3,600 rpm. or a 0.75 hp electric moto

DRUM ASSEMBLY

The drum is instantly removable by unscrewing counter-

clockwise. When inserting drum onto gearbox shaft, make sure

that drum is fully screwed onto shoulder or threads may be

damaged. Use extreme care when screwing on the drum,

spinning drum onto the gearbox shaft too fast may damage

gearbox.

ELECTRICAL

If mixer is equipped with an

electric motor

, make sure that

the power being supplied to the motor corresponds to the

voltage rating label on the motor. Supplying the wrong voltage

to the electric motor will cause severe electrical damage to

the motor.

Always make sure that

OFF/ON

switch on the electric motor

is in the

OFF

position before applying power.

It is

strongly recommended

that when plugging in the

mixer's power cord into a receptacle, that a G.F.C.I. (

Ground

Fault Current

Interrupter

) receptacle be used.

EXTENSION CABLES

The extension cable should be a 3-wire configuration that

includes a ground wire that conforms to UL code. The wire

cross section must be a minimum of 2.5 mm

. Choose an

extension cord of adequate current carrying as Reference in

Table 5. Remember

distance

affects the wire size of the

extension cable.

Ensure that the extension cable is carefully laid out avoid-

ing

wet areas

sharp edges

and locations where vehicles

might run over it. Avoid allowing the extension cable to be

trapped underneath the mixer.

Unroll the extension cable fully or it will overheat and could

catch fire. Make sure that all extension cable connections

are dry and safe. Replace any defective or badly worn ex-

tension cable immediately.

PORTABLE GENERATORS

When using a

portable generator

it must have a minimum

output of 2.5 kw and be continuous rated.

GEARBOX

The gearbox oil level has been preset at the

factory

prior to

shipping. Before inspecting the gearbox oil level (Figures 30

and 31), make sure the gearbox is cold before removing the

filler plug. Fill up with EP90. or similar gear oil.

TRANSPORTING THE MIXER

Use a ramp (Figure 3) to load and unload the mixer from the

transport vehicle. Never drop the mixer onto the ground; damage

to the mixer could result.

Figure 3. Mixer Loading

MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21) — PAGE 17

MIX N' GO MIXER — MIXER COMPONENTS

Figure 4. Mixer Components

STNIHGNIXIM.3elbaT

SNOITACILPPA

XIM

SOITAR

SEITITNAUQHCTAB

HCTAB.XORPPA

TUPTUO

.sbl211TNEMEC

).sgK05(

gaB

DNASENOTS

.TF.UCRTL.TF.UCRTL.

TF.UCRTL

yranidrOtsoM

4:2:1GAB2/14/1-1532/1-2173 58

snoitadnuoF

6:3:1GAB3/14/1-1532/1-2174/3-287

ssaMhguoR

etercnoC

8:4:1GAB4

/14/1-1532/1-2174/3-287

,sroolFthgitretaW

.ctE,stiP,sknaT

3:2/1-1:1GAB3/24/1-1533 173 58

Figure 4 shows the basic components of the

Mix N' Go

Mixer

PAGE 18 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21)

Figure 5. Engine Controls and Components

INITIAL SERVICING

The engine (Figure 5) must be checked for proper lubrication and

filled with fuel prior to operation. Refer to the manufacturers engine

manual for instructions and details of operation and servicing. The

engine shown above is a Briggs and Stratton engine, operation

for other types of engines may vary somewhat.

1. Fuel Filler Cap – Remove this cap to add unleaded

gasoline to the fuel tank. Make sure cap is tightened

securely. DO NOT over fill.

6. Throttle Lever – Used to adjust engine RPM speed (lever

advanced forward

SLOW

, lever back toward operator

FAST

7. Choke Lever – Used in the starting of a cold engine, or in

cold weather conditions. The choke enriches the fuel

mixture.

DANGER

MIX N' GO MIXER — BASIC ENGINE

Adding fuel to the tank should be done only when

the engine is stopped and has had an opportunity to

cool down. In the event of a fuel spill, DO NOT

attempt to start the engine until the fuel residue has been completely

wiped up, and the area surrounding the engine is dry.

2. Fuel Tank – Holds unleaded gasoline. For additional

information refer to engine owner's manual.

3. Recoil Starter (pull rope) – Manual-starting method. Pull

the starter grip until resistance is felt, then pull briskly and

smoothly.

4. Oil Drain Plug – Remove this plug to remove oil from the

engine's crankcase.

5. Dipstick/Oil Filler Cap – Remove this cap to determine if

the engine oil is low. Add oil through this filler port as

recommended in Table 4.

WARNING

Engine components can generate extreme heat.

To prevent burns, DO NOT touch these areas

while the engine is running or immediately after

operating. NEVER operate the engine with the

muffler removed.

Operating the engine without an air

filter, with a damaged air filter, or a

filter in need of replacement will

allow dirt to enter the engine,

causing rapid engine wear.

NOTE

8. Air Cleaner – Prevents dirt and other debris from entering

the fuel system. Remove wing-nut on top of air filter

cannister to gain access to filter element.

9. Spark Plug – Provides spark to the ignition system. Set

spark plug gap to 0.6 - 0.7 mm (0.024 - 0.028 inch) Clean

spark plug once a week.

10. Muffler - Used to reduce noise and emissions.

MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21) — PAGE 19

MIX N' GO MIXER — ASSEMBLY INSTRUCTIONS

Assembly

1. Remove the mixer drum and associated components from

the packing container (Figure 6). Match the components

against the parts list to make sure that they are all accounted

for.

Figure 6. Packing Container

4. Place the two halves of the optional support stand together

(Figure 9). The left support stand fits into the center boss on

the right support stand.

5. Insert the adapter pin through bosses as shown in Figure 9.

Once the adapter pin has been inserted and aligned, insert

the locking pin. Place the round part of the locking pin over

the bottom section of the adapter pin.

2. Place the mixer frame on a secure level surface, and attach

the top cover as shown in Figure 7.

3. Fit the mixing drum onto gearbox shaft as shown in Figure

8. Rotate drum in a clockwise direction, make sure the drum

fits right up to the shoulder on the gearbox shaft.

Figure 7. Top Cover Placement

Figure 8. Mixing Drum Placement

Figure 9. Optional Support Stand

DO NOT

spin

the drum on

fast

, as this may

damage the gearbox.

CAUTIONCAUTION

CAUTION

PAGE 20 —MIX N' GO MIXER — OPERATION & PARTS MANUAL — REV. #6 (04/15/21)

6. Tip mixer onto mouth as shown in Figure 10, and insert

support stand into frame swivel point.

9. Before attempting to lift mixer, locate the frame locking clip.

Attach the locking clip as shown in Figure 12. This will prevent

the mixing drum from moving when the mixer is positioned

in an upright position.

Figure 12. Frame Locking Clip

Figure 10. Attaching Support Stand

10. DO NOT tilt the mixer on a wet, smooth or slippery surface.

Figure 13. Slippery or Wet Surfaces

11. Once the stand has been assembled, and the locking clip has

been secured, begin tilting the mixer to an upright position.

Remember

always

tilt from the front of the mixer as shown

in Figure 14.

MIX N' GO MIXER — ASSEMBLY INSTRUCTIONS

7. Remove both wheels and wheel retainers from the packing

container.

8. Place one wheel on each side of the mixer's axle as shown

in Figure 11. Position wheel retainer over axle to secure

wheel in place. Use a rubber mallet when striking wheel

retainer.

Figure 11. Wheels and Wheel Retainers

Figure 14. Tilting Mixer to Upright Position

La page charge ...

MQ Multiquip MC3-SERIES-Briggs-Electric Mode d'emploi

Marque: MQ Multiquip

Modèle: MC3-SERIES-Briggs-Electric

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: MQ Multiquip MC3-SERIES-Briggs-Electric Operating instructions

MQ Multiquip MC3-SERIES-Briggs-Electric Mode d'emploi

MQ Multiquip MC3-SERIES-Briggs-Electric Mode d'emploi

dans d''autres langues

Autres documents