Extron NAV 10E 401 D Manuel utilisateur

Extron
Marque
Extron
Modèle
NAV 10E 401 D
Catégorie
Machine de réduction de bruit
Taper
Manuel utilisateur

Ce manuel convient également à

1
IMPORTANT:
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
DANGER: This is an All UL Notations style. Use All UL Notations for all regulatory notations including
ATTENTION, NOTES, and TIPS. The word “DANGER” must be 10 points regardless of other font size used.
A statement in 75 bold that “<whatever> may result in Serious injury or death” must start a Danger statement.
WARNING: The word “WARNING” must be 10 points regardless of other font size used.
CAUTION: This is a caution sytle. The word “CAUTION” must be 10 points regardless of other font size used.
ATTENTION: The word “ATTENTION” may be the same font size as the rest of the attention statement.
NOTE: The word “NOTE” may be the same font size as the rest of the note statement.
NAV 10E 401 D and NAV 10E 201 D • Setup Guide
CLASS 1 LASER PRODUCT, see NAV 10E 401 D and NAV 10E 201 D User Guide at www.extron.com.
WARNING: The NAV 10E 401 D and NAV 10E 201 D output continuous invisible light (Class 1 rated), which may be harmful to
the eyes; use with caution.
•
Do not look into the ber optic cable connectors or into the ber
optic cables themselves.
• Plug the attached dust caps into the optical transceivers when the ber cable is unplugged.
AVERTISSEMENT : Le NAV 10E 401 D and NAV 10E 201 D émettent une lumière invisible en continu (équipement de classe 1)
qui peut être dangereuse pour les yeux ; à utiliser avec précaution.
•
Ne pas xer dir
ectement les connecteurs optiques ou les câbles bre optique.
• Associez les bouchons anti-poussière à l’ensemble émetteur/récepteur optique lorsque le câble bre optique est débranché.
This guide provides instructions for an experienced installer to install the Extron NAV 10E 401 D and NAV 10E 201 D
streaming encoders and to make all connections. The Extron NAV encoder and one or more compatible decoders form an
AV distribution and switching matrix on a managed 10G IP network. The encoder fits in a standard US three-gang mud ring
or electrical junction box. The encoder ships with a three-gang mud ring and a decorator-style wallplate (white or black,
depending on the version ordered). The front panel faceplates are in white or black, as appropriate.
NOTE: For more information on any subject in this guide, see the NAV 10E 401 D and NAV 10E 201 D User Guide,
available at www.extron.com.
Features
HDMI IN
HDMI OUT
E
STRM
HDMI
HDCP
PWR
RESET
NAV 10G
ID
LNK
ACT
CONFIG
LAN - EXT
BBB DDDCCCAAA
FFF
EEE
NAV 10E 401
D
only
Figure 1. NAV 10E 401 D Front Panel Features
Front Panel
NOTES:
• Figure 1 shows a NAV 10E 401 D. The NAV 10E 201 D
is similar, the exception is lack of a NAV Extension port
(
D
).
• Items
C
and
F
are visible only when the faceplate is
removed.
Connectors
A
HDMI input (IN) port — Connect an HDMI cable between
this port and the HDMI output port (or DVI port, with an
appropriate adapter) of the digital video source.
B
HDMI output (OUT) port — Connect a display to this female
HDMI connector for local loop-through monitoring of the
source signal.
NOTE: See LockIt
®
Lacing Brackets on page 6 to securely fasten the HDMI connectors to the encoder for
A
and
B
.
C
Configuration (CONFIG) port — Connect a PC into the encoder for configuration of the encoder. The port uses IP over
USB technology; the IP address is always 203.0.113.22 and CANNOT be changed. The Config port is also discoverable via
Toolbelt.
D
LAN - Ext(ension) port (NAV 10E 401 D only) — If desired, connect another networked device to this port (see Ext
connector on page 8 to wire the connector). The port acts as a networked switch to the NAV 10G port (see
A
on
page 2).
2
NAV 10E 401 D and NAV 10E 201 D • Setup Guide (Continued)
Indicators and buttons (see figure 1 on page 1)
E
Visible LEDs (LEDs that are always visible) —
• Power (PWR) — Indicates power and startup status.
Blinking — The unit is receiving power and is booting up.
Lit steadily — The unit is receiving power and is operational.
•
HDMI — The encoder is detecting an HDMI input.
• HDCP — The HDMI signal is HDCP encrypted.
• Stream (STRM)— Indicates the output status of the AV stream.
Lit steadily – The encoder is actively streaming a NAV output consisting of video, audio, or both.
Blinking – The encoder is actively streaming a NAV output, but network errors are present.
F
Hidden buttons and LEDs (features that are visible only when the faceplate is removed) —
• Reset button and LED — This recessed button and LED initiate and display three modes of reset (see the NAV 10E 401 D and
NAV 10E 201 D User Guide, available at
www.extron.com, for details).
• ID button and LED — The recessed ID button identifies the encoder when pressed. The LED blinks when the encoder is in
pairing mode (see
Pairing devices on front panel on page 7 for details).
• NAV 10G LEDs — Indicate the status of the network connection.
Link LED — Lit steadily indicates that a network link is established.
Act LED — Blinking indicates network trafc. The blink rate corresponds to activity.
Rear Panel Connectors
POWER
12V
2.0A MAX
Tx Rx S
G
G
CONTROL
RS-232 IR
NAV 10G
+
CCCBBB
AAA
Figure 2. NAV 10E 401 D and NAV 10E 201 D Rear
Panel Features
A
NAV 10G port — Connects to a LAN on which one or more
decoders also reside for streaming and control.
B
CONTROL RS-232/IR port — Connect a serial RS-232 signal,
a modulated IR signal, or both to this 3.5 mm, 5-pole
direct insertion connector for bidirectional RS-232 and IR
communication with connected remote controlled devices
using an Extron control system (see Control connector on
page 8 to wire the connector).
C
Power connector — Connect the included external 12 VDC power
supply into this 2-pole direct insertion connector for local power
(see
Power connector on page 8 to wire the connector).
Installation
Step 1: Prepare the Installation Site
ATTENTION:
•
Installation and service must be performed by authorized personnel only.
• L’installation et l’entretien doivent être effectués par le personnel autorisé uniquement.
• Extron recommends installing the encoder into a grounded, UL Listed electrical junction box.
• Extron recommande d’installer le encoder dans une boîte de dérivation électrique mis à la terre, certifiée UL.
• If the encoder will be installed into fine furniture, it is best to hire a licenced, bonded craftsperson to cut the access
hole and perform the physical installation so the surface will not be damaged.
• S’il est prévu d’installer le encoder dans du beau mobilier, il est préférable de faire appel à un artisan autorisé et
qualifié pour couper le trou d’accès et réaliser l’installation de telle façon que la surface ne soit pas endommagée.
• Follow all national and local building and electrical codes that apply to the installation site.
• Respectez tous les codes électriques et du bâtiment, nationaux et locaux, qui s’appliquent au site de l’installation.
3
ATTENTION:
•
For the installation to meet UL requirements and to comply with National Electrical Code (NEC), the encoder must
be installed in a ULListed junction box. The end user or installer must furnish the junction box. It is not included with
the unit.
• Pour que l’installation respecte les exigences UL et soit conforme au National Electrical Code (NEC) américain, le
encoder doit être installé dans une boîte de dérivation certifiée UL. Il incombe à l’utilisateur final ou à l’installateur de
fournir la boîte de dérivation. Cet équipement n’est pas inclus avec l’unité.
Americans with Disabilities Act (ADA) compliance
When planning where to install the encoder, you may need to consider factors affecting accessibility of the encoder such as
height from the oor, distance from obstructions, and how far a user must reach to access the connectors. For guidelines,
see sections 307 (“Protruding Objects”) and 308 (“Reach Ranges”) of the 2010 ADA Standards for Accessible Design
available at: http://www.ada.gov/regs2010/2010ADAStandards/2010ADAStandards.pdf.
Site preparation
Mud Ring
Wall
Figure 3. Installing a Mud Ring
The encoder ts into a standard US three-gang junction box or mud ring and
decorator-style wallplate. The encoder ships with a mud ring. Optional
ULListed junction boxes, external junction boxes, and surface
mounting boxes are available for use with the unit. Read any
installation instructions and UL guidelines that come with
the mounting devices, then install the box or mud ring in the
opening at the installation site.
NOTE: Connect the network cable and the external power
supply, but do not apply power yet.
To prepare the site:
1. Using the size of the junction box or mud ring for
reference, cut the hole in the mounting surface. Protect
the surface prior to and during cutting so the surface is
not damaged.
2. Run cables to the mounting location, leaving enough
slack for device installation.
3. Install the junction box or mud ring into the wall or furniture.
4. Secure the cables with a clamp for strain relief and so
they do not slip back down into the wall or furniture.
Step 2: Install Rear Panel Cables (Behind the
Mounting Surface)
NOTE: The encoder is wider than a standard 3-gang device. You cannot install another wall-mounted device immediately
adjacent to this device.
1. Connect the encoder to the network switch (see item
A
on page 2).
2. Optional — Connect the encoder to a remote controlled device for bidirectional RS-232 and IR communication (see
item
B
on page 2).
3. Connect the encoder to an unpowered external power supply (see item
C
on page 2 and Power on page 5).
Step 3: Test Operation Before Final Installation
1. Power up the system. Check that, after approximately 45 seconds, the front panel LEDs indicate normally (Power LED
and Stream LEDs lit steadily green).
2. Make adjustments to wiring or configuration as needed. Remember that the rear panel ports are not accessible after the
encoder is mounted.
4
NAV 10E 401 D and NAV 10E 201 D • Setup Guide (Continued)
Step 4: Complete the Physical Installation
Mount the encoder to the installation surface as follows:
NOTE: Extron recommends taking safety precautions to avoid electrostatic discharge issues during installation.
1.
Insert the cabled encoder into the mud ring or junction box within the wall or furniture, aligning the mounting holes in the
encoder mounting tabs with those in box or mud ring.
2. Secure the encoder to the junction box, wall or surface mounting box, or mud ring as follows (see figure 4, below):
Flush with
Wall Surface
Wall Stud
Metal Junction Box
NAV 10E 201 D
HDMI OUT
E
E
STRM
HDMI
HDCP
PWR
W
allplate
Mounting
Scr
ews
(6 Places)
)
NOTE: Ensure that the vent holes on the top and
bottom of the encoder remain unobstructed.
Encoder
Mounting
Screws
(4 Places)
Figure 4. Installing the Encoder in a Junction Box
a.
Insert the included screws through the mounting holes at diagonal corners of the unit and into the corresponding
threaded holes in the box or mud ring.
b. Using a Phillips screwdriver, tighten the screws until snug.
ATTENTION:
• Do not overtighten the screws.
• Veillez à ne pas trop serrer les vis.
3. Attach the wallplate to the encoder:
a. Insert the six included screws through the circular holes in the wallplate and the tabs on the encoder.
b. Tighten the screws using a flat bladed screwdriver until snug.
5
Operation
Power
When power is applied, the encoder runs a series of self-tests that blink the front panel power LED and all other indicators.
The encoder then boots the NAV operating system. It can take approximately 45 seconds for self-test and system startup to
complete. When the process is complete, the power LED lights steadily.
NOTE: The encoder is NOT operational until the boot process is complete (the power LED is lit steadily).
System Operation
The encoder can be congured and controlled using embedded web pages or Toolbelt software (see the
NAV 10E 401 D and NAV 10E 201 D User Guide, available at www.extron.com).
Connection via web pages
Connection to the encoder and its embedded web pages can be made via either the front panel conguration (USB) port
(using IP over USB technology) (see figure 1,
C
on page 1) or the rear panel NAV 10G port (see figure 2,
F
on page 2).
Access the encoder using HTML pages as follows:
1. Start a web browser.
NOTES:
• Suggested browsers to fully support the NAV system are: Google Chrome™, Mozilla™ Firefox™, Microsoft
Edge™.
• The network must be properly configured for multicasting (IGMP). Failure to do so may result in degraded
performance.
2. Enter the IP address of the encoder in the browser Address field.
NOTES:
• Default settings:
Port DHCP IP address Subnet mask
Config (USB)* 203.0.113.22
NAV 10G
On
* For the Config port, the address for IP over USB
CANNOT be changed.
If the unit does not receive a DHCP address, a
self-assigned Link Local Address, is assigned in
the range 169.254.X.X.
• If you use IP over USB, Extron recommends waiting a minute after plugging in the cable for your PC to identify
the USB connection as a valid Ethernet port.
3. Press the keyboard <Enter> key. The browser displays a privacy error message (see figure 5 for an example in the
Chrome browser).
1111111111
1111
1111
2222222222
2222
2222
Figure 5. Privacy Error Message (in Chrome Browser)
NOTE: Your IT department can provide
an uploadable SSL Certificate. Once
the certificate is loaded, the notification
(figure 5) does not occur and step 3
displays figure 6. Proceed to step 6 on
page 6.
6
NAV 10E 401 D and NAV 10E 201 D • Setup Guide (Continued)
4. Click the browser button that advances past the privacy notification (such as Advanced [1] in Chrome). Explanatory text
and a link appear.
5. Click Proceed to <IP address> (unsafe) (2) (or similar message). The browser opens to the Login dialog box (see figure 6).
1111111111
1111
1111
2222222222
2222
2222
3333333333
3333
3333
Figure 6. Login Dialog Box
6.
Complete the Username (1) and Password (2) fields and click Sign In (3). The browser opens to the home page of the
embedded web pages (see figure 7).
NOTES:
• The default username is admin.
• The factory configured passwords for all accounts on this device have been set to the device serial number. If the
password is reset, the encoder defaults to the default password, which is extron.
• Usernames and passwords are case sensitive.
1111111111
1111
2222222222
2222
3333333333
3333
Figure 7. Home Page
NOTE: Detailed descriptions of communication, configuration, and monitoring are provided in the
NAV 10E 401 D and NAV 10E 201 D User Guide, available at www.extron.com.
7
Connection settings
View and change connection settings as follows:
1. On the home page, click Settings (see figure 7, 1 on page 6) >
Networking (2) > Network Connect (3). The Network Connection
pane opens (see figure 8), showing protected views of the network
connection settings.
NOTE: Editing of connection settings is disabled when the
device is assigned to an Extron NAVigator System Manager.
2. To change the settings, click Edit (see figure 8, 1). The Edit
button changes to Save.
3. Click in the desired field (2) and edit it as desired.
4. Repeat step 3 as necessary for other values.
5. Click Save.
Pairing devices on front panel
Pair devices from the front panel as follows:
1. Remove and retain the six mounting screws securing the faceplate
to the encoder (see figure 4 on page 4). Remove the faceplate.
2. Use a Tweeker or other small screwdriver to press and hold the
ID
encoder ID button on the front panel (see figure 1,
E
on
page 1) for approximately 3 seconds, until the ID LED blinks.
The encoder enters pairing mode, which allows decoders to
receive AV streams from encoders.
3. One at a time, use a Tweeker or other small screwdriver to press and
hold the decoder front panel ID button for approximately 3 seconds, until the ID LED blinks. The decoder is now paired
to the encoder.
4. Repeat steps 2 and 3 for each decoder.
5. Use a Tweeker or other small screwdriver to press and release the encoder front panel ID button. The encoder exits
pairing mode.
6. Replace the faceplate with the six screws removed in step 1.
7. Repeat steps 1 through 6 to pair decoders to other encoders.
After all devices are connected, powered on, and paired, the system is fully operational.
Operation in a System with a NAVigator
The Extron NAVigator is a system manager that easily congures and controls the NAV System. The NAVigator supports a 16
endpoint system by default, but if a LinkLicense™ is installed, it can support up to 240 endpoints.
See the NAVigator User Guide, available at www.extron.com for details.
1111111111
1111
1111
2222222222
2222
2222
Figure 8. Network Connection Pane
8
68-3124-50 Rev. A
03 21
For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the
Extron Safety and Regulatory Compliance Guide on the Extron website.
© 2021 Extron — All rights reserved. www.extron.com
All trademarks mentioned are the property of their respective owners.
Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876
Connection Details
111
222
333
444
555
LockIt
®
Lacing Brackets
1. Plug the HDMI cable into the panel connection (see
1
, at right).
2. Loosen the HDMI connection mounting screw from the panel enough to allow
the LockIt lacing bracket to be placed over it (
2
). The screw does not have to be
removed.
3. Place the LockIt lacing bracket on the screw and against the HDMI connector (
3
).
4. Tighten the screw to secure the bracket.
ATTENTION:
• Do not overtighten the HDMI connector mounting screw. The shield it fastens to is very thin and can easily be
stripped.
• Ne serrez pas trop la vis de montage du connecteur HDMI. Le blindage auquel elle est attachée est très n et
peut facilement être dénudé.
5. Loosely place the included tie wrap around the HDMI connector and the LockIt lacing bracket as shown (
4
).
6. While holding the connector securely against the lacing bracket, use pliers to tighten the tie wrap, then remove any
excess length (
5
).
Control connector Ext connector Power connector
TxRx
RxTx Gnd
IR Device
RS-232 Device
Tx Rx S
G
G
CONTROL
RS-232 IR
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
TIA/EIA T568B
TP Wires
12345678
Pins:
SECTION A–A
Ridges
Smooth
Power Supply
Output Cord
AA
Direct
Insertion
Connector
3"
16
(5 mm) MAX
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Extron NAV 10E 401 D Manuel utilisateur

Extron
Marque
Extron
Modèle
NAV 10E 401 D
Catégorie
Machine de réduction de bruit
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes