ESAB EMP 235ic Manuel utilisateur

0463 479 001 20170220

Valid for: serial no. EMP235ic:636-xxx-xxxx,

EM235ic:640-xxx-xxxx

EMP235ic, EM235ic

US Instruction manual

CA Manuel d’instructions

XL Instrucciones de uso

TABLE OF CONTENTS

0463 479 001 © ESAB AB 2017

ENGLISH US .......................................................................................................... 3

CANADIAN FRANÇAIS .......................................................................................... 40

ESPAÑOL SA ......................................................................................................... 79

TABLE OF CONTENTS

0463 479 001 © ESAB AB 2017

1

SAFETY PRECAUTIONS ..............................................................................

5

1.1 Meaning of symbols.................................................................................

5

1.2 Safety guidance and information............................................................

5

1.3 User responsibility ...................................................................................

10

2

INTRODUCTION............................................................................................

11

2.1 Equipment.................................................................................................

12

3

TECHNICAL DATA ........................................................................................

13

4

INSTALLATION..............................................................................................

15

4.1 Location.....................................................................................................

16

4.2 Lifting instructions...................................................................................

16

4.3 Electrical supply.......................................................................................

16

4.3.1 Recommended fuse sizes and minimum cable area.............................. 17

4.3.2 Connecting the power source to input supply ........................................ 18

5

OPERATION ..................................................................................................

18

5.1 Connections..............................................................................................

20

5.2 Connecting welding and return cables ..................................................

20

5.3 Polarity change.........................................................................................

21

5.4 Inserting and replacing wire....................................................................

21

5.5 Setting the wire feed pressure ................................................................

23

5.6 Changing the feed/pressure rollers........................................................

23

5.7 Shielding gas ............................................................................................

24

5.8 Volt-Ampere curves..................................................................................

25

5.9 Duty cycle .................................................................................................

27

5.10 Overheating protection............................................................................

28

6

CONTROL PANEL.........................................................................................

28

6.1 How to navigate - EMP235ic....................................................................

28

6.1.1 Main menu.............................................................................................. 29

6.1.2 sMIG mode............................................................................................. 29

6.1.3 Manual MIG mode.................................................................................. 29

6.1.4 Flux cored wire mode ............................................................................. 30

6.1.5 Stick mode.............................................................................................. 30

6.1.6 LIFT-TIG mode (EMP235ic only)............................................................ 30

6.1.7 Settings .................................................................................................. 31

6.1.8 User manual information ........................................................................ 31

6.1.9 Icon reference guide............................................................................... 31

6.2 How to navigate - EM235ic ......................................................................

34

6.2.1 Symbol reference EM235ic .................................................................... 34

7

MAINTENANCE.............................................................................................

35

7.1 Routine maintenance ...............................................................................

35

7.2 Power source and wire feeder maintenance .........................................

36

7.3 Torch and liner maintenance...................................................................

37

8

TROUBLESHOOTING...................................................................................

38

TABLE OF CONTENTS

0463 479 001 © ESAB AB 2017

9

ORDERING SPARE PARTS ..........................................................................

39

MIG WELD PARAMETER CHART ....................................................................... 118

FRACTION TO DECIMAL CONVERSION ........................................................... 120

DIAGRAM ............................................................................................................. 121

ORDERING NUMBERS........................................................................................ 122

WEAR PARTS....................................................................................................... 123

ACCESSORIES .................................................................................................... 125

REPLACEMENTS PARTS.................................................................................... 126

Rights reserved to alter specifications without notice.

1 SAFETY PRECAUTIONS

0463 479 001

- 5 -

1 SAFETY PRECAUTIONS

1.1 Meaning of symbols

As used throughout this manual: Means Attention! Be Alert!

DANGER!

Means immediate hazards which, if not avoided, will result in immediate,

serious personal injury or loss of life.

WARNING!

Means potential hazards which could result in personal injury or loss of

life.

CAUTION!

Means hazards which could result in minor personal injury.

1.2 Safety guidance and information

WARNING!

Before use, read and understand the instruction manual

and follow all labels, employer's safety practices and Safety

Data Sheets (SDSs).

WARNING!

These Safety Precautions are for your protection. They summarise precautionary

information from the references listed in the Additional Safety Information section.

Before performing any installation or operating procedures, be sure to read and

follow the safety precautions listed below as well as all other manuals, material

safety data sheets, labels, etc. Failure to observe the Safety Precautions could

result in injury or death.

PROTECT YOURSELF AND OTHERS

Some welding, cutting and gouging processes are noisy and require

hearing protection. The arc, like the sun, emits ultraviolet (UV) and

other radiation and can injure the skin and eyes. Hot metal can cause

burns. Training in the proper use of the processes and equipment is

essential to prevent accidents. Therefore:

1. Wear a welding helmet fitted with a proper shade of filter to protect your face and eyes

when welding or watching.

2. Always wear safety glasses with side shields in any work area, even if welding

helmets, face shields and/or goggles are also required.

3. Use a face shield fitted with the correct filter and cover plates to protect your eyes,

face, neck and ears from sparks and rays of the arc when operating or observing

operations. Warn bystanders not to look at the arc and not to expose themselves to

the rays of the electric-arc or hot metal.

1 SAFETY PRECAUTIONS

0463 479 001

- 6 -

4. Wear flameproof gauntlet-type gloves, heavy long-sleeve shirt, cuffless pants,

high-topped shoes, and a welding helmet or cap for personal protection; in order to

protect against arc rays and hot sparks or hot metal. A flameproof apron may also be

desirable as additional protection against radiated heat and sparks.

5. Hot sparks or metal can lodge in rolled up sleeves, trouser cuffs, or pockets. Sleeves

and collars should be kept buttoned (closed) and open pockets should be eliminated

from the front of the clothing.

6. Protect other personnel from arc rays and hot sparks with a suitable non-flammable

partition or curtains. Post warning signs advising others not to watch the welding arc

or be in direct exposure to the active arc without proper protection.

7. Use goggles or face shields over safety glasses when chipping slag or grinding.

Chipped slag may be hot and can fly for long distances. Bystanders should also wear

goggles over safety glasses.

FIRES AND EXPLOSIONS

The heat from flames and arcs can start fires. Hot slag or sparks can

also cause fires and explosions. Therefore:

1. Protect yourself and others from flying sparks and hot metal.

2. Remove all combustible materials well away from the work area or cover the materials

with an approved protective non-flammable covering. Combustible materials include

wood, cloth, sawdust, liquid and gas fuels, solvents, paints, and coating paper, etc.

3. Hot sparks or hot metal can fall through cracks or crevices in floors or wall openings

and cause a hidden smoldering fire or fires on the floor below. Make certain that such

openings are protected from hot sparks and metal.

4. Follow the "hot work" procedures for the location. This can include a fire watch person

who monitors the sparks during the work, the requirement for a formal work permit and

the surveillance of the scene for an extended period of time to ensure no smoldering

fires are developing.

5. Do not weld, cut, or perform other hot work until the work piece has been completely

cleaned so that there are no substances on or in the work piece which might produce

flammable or toxic vapors. Do not perform hot work on closed containers, they may

explode.

6. Have fire extinguishing equipment handy for instant use, such as a garden hose,

water pail, sand bucket, or portable fire extinguisher. Be sure you are trained in its

use.

7. Do not use equipment beyond its ratings. For example, an overloaded welding cable

can overheat and create a fire hazard.

8. After completing work, inspect the work area to make sure there are no hot sparks or

hot metal that could cause a fire later. Use fire watchers when necessary.

ELECTRICAL SHOCK

Contact between live electrical parts and earth can cause severe injury

or death. DO NOT use AC welding current in damp areas, if movement

is confined, or if there is danger of falling. Therefore:

1. Be sure the power source frame (chassis) is connected to the earth system of the

input power. All ground points should be verified with periodic testing by an electrician.

2. Connect the workpiece to a good electrical earth.

3. Connect the work cable to the workpiece. A poor or missing connection can expose

you or others to a fatal shock.

4. Use well-maintained equipment. Replace worn or damaged cables.

5. Keep everything dry, including clothing, work area, cables, torch/electrode holder and

power source.

1 SAFETY PRECAUTIONS

0463 479 001

- 7 -

6. Make sure that all parts of your body are insulated from both the work piece and from

the ground.

7. Do not stand directly on metal or the ground while working in tight quarters or a damp

area; stand on an effective insulation layer, such as dry boards, an insulating platform,

and wear rubber-soled shoes.

8. Put on dry, hole-free gloves before turning on the power.

9. Turn off the power, before removing your gloves.

10. Refer to ANSI/ASC Standard Z49.1 for specific grounding recommendations. Do not

mistake the work lead for a earth cable.

ELECTRIC AND MAGNETIC FIELDS

May be dangerous. Electric current flowing through any conductor

causes localized Electric and Magnetic Fields (EMF). Welding and

cutting current creates EMF around welding cables and welding

machines. Therefore:

1. Welders with medical pacemakers fitted should consult their doctor before welding.

EMF may interfere with some pacemakers.

2. Exposure to EMF may have other health effects which are unknown.

3. Welders should use the following procedures to minimize exposure to EMF:

a) Route the electrode and work cables together. Secure them with tape when

possible.

b) Never coil the torch or work cable around your body.

c) Do not place your body between the torch and work cables. Route cables

together on the same side of your body.

d) Connect the work cable to the workpiece as close as possible to the area being

welded.

e) Keep the welding power source and cables as far away from your body as

possible.

FUMES AND GASES

Fumes and gases, can cause discomfort or harm, particularly in

confined spaces. Shielding gases can cause asphyxiation. Therefore:

1. Keep your head out of the fumes, smoke, and vapors. Do not breathe the smoke,

fumes, and gases that are generated by welding processes.

2. Always provide adequate ventilation in the work area by natural or mechanical means.

Do not weld, cut or gouge on materials such as galvanized steel, stainless steel,

copper, zinc, lead beryllium or cadmium unless positive mechanical ventilation is

provided. Do not breathe in the fumes from these materials.

3. Orient the ventilation to draw smoke, fumes, and vapors in a direction away from the

welding operator. Position ventilation suction to pull welding fumes and smoke from

the far side of the work area if possible

4. Provide general ventilation for the surrounding work area if there is a risk of workers or

other persons beyond the immediate work area getting exposed to significant welding

fumes. Monitor the fugitive fumes and smoke for potential collateral exposures. Install

appropriate ventilation controls or cease surrounding activity if fumes become an

exposure issue outside of the immediate work area

5. Do not operate near degreasing and spraying operations. The heat or arc can react

with chlorinated hydrocarbon vapors or liquids to form phosgene, a highly toxic gas,

and other irritant gases.

1 SAFETY PRECAUTIONS

0463 479 001

- 8 -

6. If you develop momentary eye, nose or throat irritation while operating, this is an

indication that the ventilation is not adequate. Stop work and take the necessary steps

to improve ventilation in the work area. Do not continue to operate if physical

discomfort persists.

7. Respiratory protection is required if worker respiratory exposures to fumes exceed

recommended thresholds. Those thresholds can only be accurately measured through

standardized industrial hygiene sampling protocols. Seek the assistance of specialists

if your work causes respiratory exposures or you have other exposure concerns.

8. Refer to ANSI/ASC Standard Z49.1 for specific ventilation recommendations.

9. WARNING: This product when used for welding or cutting, typically produces fumes or

gases which contain chemicals known to the State of California that can cause birth

defects and in some cases cancer (California Health & Safety Code §25249.5 et seq.)

CYLINDER HANDLING

Cylinders, if mishandled, can rupture and violently release gas. A

sudden rupture of the cylinder valve or relief device can injure or kill.

Therefore:

1. Locate cylinders away from heat, sparks and flames.

2. Inspect all connections before use to detect and correct any leaks or system defects.

Use soapy water as a test if you suspect a leak but have difficulty confirming its

location or existence.

3. Never strike an arc on a cylinder. Handle cylinders with care and avoid jolts and

impacts to cylinders; regardless of if they are empty, partial, or full.

4. Secure all cylinders in a way that prevents them from falling and potentially doing

damage to the valve, regulator, or attachments. Typically, this requires the use of a

secure strap or chain at an appropriate height that helps to prevent the cylinder from

falling over.

5. Use the proper gas for the process and use the proper pressure reducing regulator

designed to operate from the compressed gas cylinder. Do not use adapters. Maintain

hoses and fittings in good condition. Follow the manufacturer's operating instructions

for mounting a regulator to a compressed gas cylinder.

6. Never secure cylinders to work tables or fixtures where they may become part of an

electrical circuit.

7. When not in use, keep cylinder valves closed. Have valve protection cap in place if

regulator is not connected. Secure and move cylinders by using suitable hand trucks.

MOVING PARTS

Moving parts, such as fans, rotors and belts can cause injury.

Therefore:

1. Keep all doors, panels, guards, and covers closed and securely in place.

2. Stop the engine or drive systems before installing or connecting a unit.

3. Have only qualified people remove covers for maintenance and troubleshooting as

necessary

4. To prevent accidental starting of equipment during service, disconnect negative (-)

battery cable from battery. Monitor the battery to prevent accidental reconnection

before the work is done and the area is clear for restarting.

5. Keep hands, hair, loose clothing and tools away from moving parts. Do not use gloves

near moving parts.

6. Reinstall panels or covers and close doors when service is finished and before starting

engine.

1 SAFETY PRECAUTIONS

0463 479 001

- 9 -

WARNING!

FALLING EQUIPMENT CAN INJURE

• Only use lifting eye to lift unit. Do NOT use running gear, gas cylinders or

any other accessories.

• Use equipment of adequate capacity to lift and support unit.

• If using lift forks to move unit, be sure forks are long enough to extend

beyond opposite side of unit.

• Keep cables and cords away from moving vehicles and moving

equipment when working from an aerial location.

WARNING!

EQUIPMENT MAINTENANCE

Faulty or improperly maintained equipment can cause injury or death.

Therefore:

1. Always have qualified personnel perform the installation, troubleshooting

and maintenance work. Do not perform any electrical work unless you

are qualified to perform such work.

2. Before performing any maintenance work inside a power source,

disconnect the power source from the incoming electrical power.

3. Maintain cables, earthing wire, connections, power cord and power

supply in safe working order. Do not operate any equipment in faulty

condition.

4. Do not abuse any equipment or accessories. Keep equipment away from

heat sources such as furnaces, wet conditions such as water puddles, oil

or grease, corrosive atmospheres and inclement weather.

5. Keep all safety devices and cabinet covers in position and in good repair.

6. Use equipment only for its intended purpose. Do not modify it in any

manner.

CAUTION!

ADDITIONAL SAFETY INFORMATION

For more information on safe practices for electric arc welding and cutting

equipment, ask your supplier for a copy of “Precautions and Safe Practices

for Arc Welding, Cutting and Gouging.” Form 52-529.

The following publications are recommended to you:

1. ANSI/ASC Z49.1 - "Safety in Welding and Cutting"

2. AWS C5.5 - "Recommended Practices for Gas Tungsten Arc Welding"

3. AWS C5.6 - "Recommended Practices for Gas Metal Arc Welding"

4. AWS SP - "Safe Practices" - Reprint, Welding Handbook

5. ANSI/AWS F4.1 - "Recommended Safe Practices for Welding and

Cutting of Containers That Have Held Hazardous Substances"

6. OSHA 29 CFR 1910 - "Safety and Health Standards"

7. CSA W117.2 - "Code for Safety in Welding and Cutting"

8. NFPA Standard 51B, “Fire Prevention During Welding, Cutting, and

Other Hot Work"

9. CGA Standard P-1, “Precautions for Safe Handling of Compressed

Gases in Cylinders”

1

0.

ANSI Z87.1, "Occupational and Educational Personal Eye and Face

Protection Devices"

1 SAFETY PRECAUTIONS

0463 479 001

- 10 -

1.3 User responsibility

Users of ESAB equipment have the ultimate responsibility for ensuring that anyone who

works on or near the equipment observes all the relevant safety precautions. Safety

precautions must meet or exceed the standard requirements that apply to this type of

equipment. The following recommendations should be observed, in addition to the standard

regulations that apply to the workplace.

All work must be carried out by trained personnel well-acquainted with the operation of the

equipment. Incorrect operation of the equipment may lead to hazardous situations, which

could result in injury to the operator and damage to the equipment.

1. Anyone who uses the equipment must be familiar with:

○ its operation

○ location of emergency stops and safety features

○ its function

○ the relevant safety precautions

○ welding and cutting methods or other applicable operations of the equipment

2. The operator must ensure that:

○ no unauthorized person is within the working area of the equipment when it is

started up

○ no-one is unprotected when the arc is struck or work is started with the

equipment

3. The workplace must:

○ be suitable for the purpose

○ be free from drafts to the extent possible, in order to maintain effective

ventilation and the control of welding fumes and work byproducts

4. Personal safety equipment:

○ Always wear recommended personal safety equipment, such as safety glasses,

flame-proof clothing, safety gloves

○ Do not wear loose-fitting items, such as scarves, bracelets, rings, etc., which

could become trapped or cause burns

5. General precautions:

○ Make sure the return cable is connected securely

○ Work on high voltage equipment may only be carried out by a qualified

electrician

○ Appropriate fire extinguishing equipment must be clearly marked and close at

hand

○ Lubrication and maintenance must not be carried out on the equipment during

operation

WARNING!

Arc welding and cutting may cause injury to yourself and others. Take

precautions when welding and cutting. Ask for your employer's safety practices,

which should be based on the manufacturer's hazard data.

2 INTRODUCTION

0463 479 001

- 11 -

ELECTRIC SHOCK - Can kill

• Install and ground the unit in accordance with applicable standards

• Do not touch live electrical parts or electrodes with bare skin, wet

gloves, or wet clothing

• Insulate yourself from the ground and the workpiece

• Ensure your working position is safe

FUMES AND GASES - Can be dangerous to your health

• Keep your head out of the fumes

• Use ventilation, extraction at the arc, or both, to take fumes and

gases away from your breathing zone and the general area

ARC RAYS - Can injure eyes and burn skin

• Protect your eyes and body. Use the correct welding darkening

screen and filter lens, and wear protective clothing

• Protect bystanders with suitable screens or curtains

FIRE HAZARD

• Sparks (spatter) can cause a fire. Therefore, make sure that there are

no flammable/combustible materials nearby

• Take steps to monitor the work area for fugitive sparks that could

cause a fire, either immediately or after smoldering over time

NOISE - Excessive noise can damage hearing

Protect your ears. Use earmuffs or other hearing protection with the

appropriate level of noise reduction/hearing protection.

MALFUNCTION - Call for expert assistance in the event of malfunction.

PROTECT YOURSELF AND OTHERS!

WARNING!

Do not use the power source for thawing frozen pipes.

CAUTION!

This product is solely intended for arc welding.

ESAB has an assortment of welding accessories and personal protection equipment

for purchase. For ordering information, contact your local ESAB dealer or visit us on

our website.

2 INTRODUCTION

The ESAB EM and EMP product family is a new generation of MIG and multi-process

(MIG/Stick/TIG) welding power sources.

All Rebel power sources are designed to match the needs of the user. They are tough,

durable and portable, providing excellent arc performance across a variety of welding

applications.

The EMP features a 4.3in. (11cm) color TFT user interface display which provides quick and

easy selection of weld process and parameters, suitable for both newly trained and

intermediate level users. For more advanced users a number of functions could be

introduced and customized to give maximum flexibility.

2 INTRODUCTION

0463 479 001

- 12 -

Exclusive to ESAB, sMIG provides users with excellent short circuit transfer arc

characteristics.

The EM and EMP family connects to 120V–230V,1~50/60Hz input power supplies,

supplied by mains or generator power. Incorporating a PFC (Power Factor Correction) circuit

significantly increases power efficiency.

Key features:

• Excellent MIG characteristics (EM)

• Excellent multi-process, MIG/Stick and Lift/TIG (EMP) welding capabilities

• Automatic recognition of input power with PFC (120V–230V)

• Large 4.3in. (11cm) high resolution customizable user interface (EMP)

• Rugged case design and internal hardware

• Portable

• High grade cast aluminum wire drive system provides excellent control of drive roll

geometry ensuring smooth, precise wire feeding

• Professional high grade accessories

2.1 Equipment

Package consists of the following:

EMP series

• ESAB EMP235ic power source

• Tweco® Spray Master 250A MIG gun with 15ft (5m) cable, 0.030in., 0.035in.,

0.045in. (0.8mm, 0.9mm, 1.2mm) contact tips and Allen key

• ESAB stick electrode holder, 12ft (4m), 200A

• Ground clamp, 10ft (3m), 250A

• Input cable 10ft (3m) with 230V plug (part of power source)

• Power adapter cable (230V to 120V, 15A)

• Victor® Flow Meter with 10ft (3m) gas hose

• ESAB OK AristoRod™ premium solid wire 0.035in. (0.9mm) 11# spool

• ESAB Atom Arc Acclaim 1/8in. premium stick electrodes 1# sample pack

• Drive roll, 0.023in. /0.030in. / 0.035in. / 0.045in. (0.6 mm / 0.8mm / 0.9mm /

1.2mm)

• Guide tubes 0.023in. – 0.045 in. (0.6mm – 1.2mm)

• Thickness gauge tool

• USB stick including manuals

• Safety manual

• Quick start guide

3 TECHNICAL DATA

0463 479 001

- 13 -

EM series

• ESAB EM235ic power source

• Tweco® Spray Master 250A MIG gun with 15ft (4.5m) cable, 0.030in., 0.035in.,

0.045in. (0.8mm, 0.9mm, 1.2mm) contact tips and Allen Key

• Ground clamp, 10ft (3m), 250A

• Input cable 10ft (3m) with 230V plug (part of power source)

• Power adapter cable (230V to 120V, 15A)

• Victor® Flow Meter with 10ft (3m) gas hose

• ESAB OK AristoRod™ premium solid wire 0.035in. (0.9mm) 11# spool

• ESAB Atom Arc Acclaim 1/8in. premium stick electrodes 1# sample pack

• Guide tubes 0.023in. – 0.045 in. (0.6mm – 1.2mm)

• Thickness gauge tool

• USB stick including manuals

• Safety manual

• Quick start guide

3 TECHNICAL DATA

EMP235ic

Voltage 230V, 1 ~ 50/60Hz 120V, 1 ~ 50/60Hz

Primary current

I

max.

GMAW - MIG

32.1A

Breaker 20A: 28.6A

Breaker 15A: 20.3A

I

max.

GTAW - TIG

26.1A Breaker 15A: 20.8A

I

max.

SMAW - Stick

31.3A Breaker 15A: 20.8A

I

eff.

GMAW - MIG

20.31A

Breaker 20A: 18.0A

Breaker 15A: 14.6A

I

eff.

GTAW - TIG

19.8A Breaker 15A: 14.7A

I

eff.

SMAW - Stick

16.5A Breaker 15A: 14.7A

Permissible load at GMAW - MIG

100% duty cycle 160A/22.0V Breaker 15A: 75A/17.75V

Breaker 20A: 90A/18.5V

60% duty cycle 200A/24.0V Breaker 15A: 90A/18.5V

Breaker 20A: 110A/19.5V

40% duty cycle 235A/25.75V Breaker 15A: 100A/19V

20% duty cycle – Breaker 20A: 130A/20.5V

Setting range (DC) 15A/14.75V –

250A/30.0V

15A/14.75V –

130A/20.5V

Permissible load at GTAW - TIG

100% duty cycle 170A/16.8V 100A/14V

60% duty cycle 215A/18.6V 120A/14.8V

40% duty cycle – 130 A/15.2V

30% duty cycle 240A/19.6V –

Setting range (DC) 5 A/10.2V – 240A/19.6V 5 A/10.2V – 200A/18.0V

3 TECHNICAL DATA

0463 479 001

- 14 -

EMP235ic

Permissible load at SMAW - Stick

100% duty cycle 130A/25.2V 65A/22.6V

60% duty cycle 170A/26.8V 80A/23.2V

40% duty cycle – 85A/23.4V

25% duty cycle 210A/28.4V –

Setting range (DC) 16 A/20.6 V – 210A/28.4V 16 A/20.6 V – 130A/25.2V

Open circuit voltage (OCV)

VRD deactivated 68V 68V

VRD activated 35V 35V

Efficiency 85% 84%

Power factor 0.98 0.99

Wire feed speed 80-700in./min

(2.0-17.89m/min)

80-700in./min

(2.0-17.89m/min)

Wire diameter

Mild steel solid wire 0.023–0.045in. (0.6–1.2mm) 0.023–0.045in. (0.6–1.2mm)

Stainless steel solid wire 0.030–0.045in. (0.8–1.2mm) 0.030–0.045in. (0.8–1.2mm)

Flux cored wire 0.030-0.052in. (0.8-1.3mm) 0.030-0.052in. (0.8-1.3mm)

Aluminum 0.030–0.045in. (0.8–1.2mm) 0.030–0.045in. (0.8–1.2mm)

Bobbin size Ø 4–12in. (100–300mm) Ø 4–12in. (100–300mm)

Dimensions l×w×h 23×9×16in.

(548×229×406mm)

23×9×16in.

(548×229×406mm)

Weight 53lbs (24kg) 53lbs (24kg)

Operating temperature -14to+104°F (-10to+40°C) -14to+104°F (-10to+40°C)

Enclosure class IP23S IP23S

Application classification

EM235ic

Voltage 230 V, 1 ~ 50/60 Hz 120 V, 1 ~ 50/60 Hz

Primary current

I

max.

GMAW - MIG

32.1A

Breaker 20A: 28.6A

Breaker 15A: 20.3A

I

eff.

GMAW - MIG

20.31A

Breaker 15A: 14.6A

Breaker 20A: 18.0A

Permissible load at GMAW - MIG

100% duty cycle 160A/22.0V Breaker 15A: 75A/17.75V

Breaker 20A: 90A/18.5V

60% duty cycle 200A/24.0V Breaker 15A: 90A/18.5V

Breaker 20A: 110A/19.5V

40% duty cycle 235A/25.75V Breaker 15A: 100A/19V

20% duty cycle – Breaker 20 A: 130 A/20.5 V

4 INSTALLATION

0463 479 001

- 15 -

EM235ic

Setting range (DC) 15A/14.75V–250A/30.0

V

15A/14.75V–130A/20.5

V

Open circuit voltage (OCV)

VRD deactivated 68V 68V

VRD activated 35V 35V

Efficiency 84% 84%

Power factor 0.98 0.99

Wire feed speed 60-700in./min

(1.5-17.89m/min)

60-700in./min

(1.5-17.89m/min)

Wire diameter

Mild steel solid wire 0.023–0.045in. (0.6–1.2mm) 0.023–0.045in. (0.6–1.2mm)

Stainless steel solid wire 0.030–0.045in. (0.8–1.2mm) 0.030–0.045in. (0.8–1.2mm)

Flux cored wire 0.030-0.052in. (0.8-1.3mm) 0.030-0.052in. (0.8-1.3mm)

Aluminum 0.030–0.045in. (0.8–1.2mm) 0.030–0.045in. (0.8–1.2mm)

Bobbin size Ø 4–12in. (100–300mm) Ø 4–12in. (100–300mm)

Dimensions l×w×h 23×9×16in.

(548×229×406mm)

23×9×16in.

(548×229×406mm)

Weight 53lbs (24kg) 53lbs (24kg)

Operating temperature -14 to +104°F (-10to+40°C) -14 to +104°F (-10to+40°C)

Enclosure class IP23S IP23S

Application classification

Duty cycle

The duty cycle refers to the time as a percentage of a ten-minute period that you can weld at

a certain current without overheating. The duty cycle is valid for 104°F / 40°C.

For more information, see section "Duty cycle" in the OPERATION chapter.

Enclosure class

The IP code indicates the enclosure class, i.e. the degree of protection against penetration

by solid objects or water.

Equipment marked IP 23S is intended for indoor and outdoor use; however, should not be

operated in precipitation.

Application class

The symbol indicates that the power source is designed for use in areas with increased

electrical hazard.

4 INSTALLATION

The installation must be carried out by a professional.

CAUTION!

This product is intended for industrial use. In a domestic environment, this

product may cause radio interference. It is the user's responsibility to take

adequate precautions.

4 INSTALLATION

0463 479 001

- 16 -

4.1 Location

Position the power source so that its cooling air inlets and outlets are not obstructed.

A. 4in. (100 mm)

B. 4in. (100 mm)

4.2 Lifting instructions

The power source can be lifted using any of the handles.

Secure the equipment - particularly if the ground is

uneven or sloping.

4.3 Electrical supply

The supply voltage should be 230V AC ±10% or 120V ±10%. Too low supply voltage may

cause poor welding performance. Too high of welding supply voltage will cause components

to overheat and possibly fail. Contact the local electric utility for information about the type of

electrical service available, how proper connections should be made, and inspection

required.

4 INSTALLATION

0463 479 001

- 17 -

The Welding power source must be:

• Correctly installed, if necessary, by a qualified electrician.

• Correctly grounded (electrically) in accordance with local regulations.

• Connected to the correct size power point and fuse as indicated in table below.

WARNING!

Do not connect an input (WHITE or BLACK) conductor to the ground terminal.

Do not connect the ground (GREEN) conductor to an input line terminal.

NOTE!

Use the welding power source in accordance with the relevant national

regulations.

CAUTION!

Disconnect input power and secure employing ‘Lock-out’ / ‘Tagging’ procedures.

Ensure input power line disconnect switch is locked (lock-out/Tagging) in the

‘Open’ position BEFORE removing input power fuses. Connection/Disconnect

should be carried out by competent persons.

Rating plate with supply connection data

4.3.1 Recommended fuse sizes and minimum cable area

WARNING!

An electrical shock or fire hazard is probable if the following electrical service

guide recommendations are not followed. These recommendations are for a

dedicated branch circuit sized for the rated output and duty cycle of the welding

power source.

120 – 230V, 1 ~ 50/60Hz

Supply voltage 230V AC 120V AC

Input current at maximum output 48A 30A

Maximum recommended fuse* or circuit breaker rating

*Time delay fuse UL class RK5, refer to UL 248

40A 30A

Maximum recommended fuse* or circuit breaker rating

*Normal operating UL class K5, refer to UL 248

50A 50A

Minimum recommended cord size 10AWG

(5.3mm

2

)

12AWG

(4mm

2

)

5 OPERATION

0463 479 001

- 18 -

120 – 230V, 1 ~ 50/60Hz

Maximum recommended extension cord length 50ft (15m) 25ft (8m)

Minimum recommended grounding conductor size 10AWG

(5.3mm

2

)

12AWG

(4mm

2

)

Supply from power generators

The power source can be supplied from different types of generators. However, some

generators may not provide sufficient power for the welding power source to operate

correctly. Generators with Automatic Voltage Regulation (AVR) or with equivalent or better

type of regulation, with 10kW rated power, are recommended.

4.3.2 Connecting the power source to input supply

Use one of the supplied adapters to connect the power source to mains.

5 OPERATION

General safety regulations for handling the equipment can be found in the "SAFETY

PRECAUTIONS" chapter of this manual. Read it through before you start using the

equipment!

NOTE!

When moving the equipment, use the intended handle. Never pull on the cables.

5 OPERATION

0463 479 001

- 19 -

WARNING!

Rotating parts can cause injury, take great care.

WARNING!

Electric shock! Do not touch the workpiece or the welding head during operation!

WARNING!

Make sure that the side covers are closed during operation.

WARNING!

Ensure spool retaining cotter pin is in place to prevent the spool from sliding off

the hub.



5 OPERATION

0463 479 001

- 20 -

5.1 Connections

Front and rear:

1. Knob for current or wire feed speed

selection (EMP)

10. Torch connection

2. Display (EMP) 11. Mains cable

3. Knob for voltage selection (EMP) 12. Mains supply switch ON/OFF

4. Main knob for menu navigation (EMP) 13. Gas valve inlet for TIG/Spool-gun

5. Gas valve output for TIG/Spool-gun 14. Gas valve inlet for MIG/MAG

6. Torch/Remote control connection 15. Knob for voltage selection (EM)

7. Negative output [-] 16. Display LED - Volt/Ampere (EM)

8. Polarity changeover cable 17. Knob for wire feed (EM)

9. Positive output [+] 18. Knob for process selection (EM)

5.2 Connecting welding and return cables

The power source has two outputs for connecting welding and return cables: A negative [-]

terminal (7) and a positive [+] terminal (9); see front illustration.

For the TIG process, connect the TIG torch trigger remote or foot control to the remote

receptacle (6); see front illustration. Connect the TIG torch gas connector to the gas outlet

receptacle (5). Connect gas input supply from a regulated shielding gas supply to the gas

inlet connector (13) located on the rear of the machine.

For MIG/Stick process the output to which the welding cable is connected depends on the

type of electrode, refer to electrode packaging for information relating to the correct electrode

polarity. Connect the return cable to the remaining welding terminal on the power source.

La page charge ...

ESAB EMP 235ic Manuel utilisateur

Ce manuel convient également à

ESAB EMP 235ic Manuel utilisateur

dans d''autres langues

Documents connexes