LucidSound LS50X Mode d'emploi

Taper
Mode d'emploi
USER GUIDE
WIRELESS GAMING HEADSET
WITH BLUETOOTH
SETUP IMPORTANT !
To complete setup for Xbox One and
enable surround sound go to:
The LS50 headset has two modes
for volume control:
Gaming Control Mode
Left volume wheel controls the level
of the incoming audio from the dongle
(connected to your Xbox One).
Bluetooth Control Mode
Left volume wheel controls the volume
level of the audiocoming from your
Bluetooth device.
To switch between the two control
modes, press and hold the left earcup
button for 1 second.
XBOX ONE FAQ
32
1
http://bit.ly/2ZpBuzK
http://bit.ly/30IQUMj
[R]
Game / Chat Balance
Bluetooth Track forward / Track back
Mic Mute
Mic Monitoring
Mute/Unmute = Short Press
LED on Boom Mic
illuminates when muted
Mic Monitor On/O = Press and hold
for 3 seconds
EQ/Bluetooth button
[L]
Volume Wheel
Center Button
Microphone Port
Power Button
USB Charging Port
Power/Charging LED
Bluetooth LED
Mobile 3.5mm Port
Solid = ON/Connected/Charged
Slow Blink = Not Connected
Pulsing = Charging
Press and hold for 1 second to toggle between Bluetooth and Gaming modes
Double click to check battery level
Audio mute in Gaming mode
Play/Pause/Answer/Hangup in Bluetooth mode
Solid = Connected
Slow Blink = Not Connected
Double Blink = Pairing mode Press and release to cycle through EQs
Press and hold for 1 second to activate
Bluetooth voice assistant
Press and hold for 4 seconds for
Bluetooth pairing
HEADSET HEADSET
CHARGING MOBILE SETUP
Pulsing = Charging
Solid = Charged
ACCESSORIES
Boom Mic
1
3.5mm Cable
4
USB Charging Cable
3
USB Base Station
Mic Port Cover
2
Press and hold the EQ/BT button for 4 seconds to enter pairing mode
Search for Bluetooth devices on mobile phone and choose “LucidSound LS50”
MICROPHONE
IN 5V
MIC
IN 5V
MIC
5Travel
Case
6
SUPPORT ?#!*
Dongle Model No: LS50XTX FCC ID: 2AGZW06430 IC ID: 21203-06430
Headset Model No: LS50RX FCC ID: 2AGZW03595 IC ID: 21203-03595
RF Frequency: 2.40335 GHz to 2.47935 GHz
Output Power: TX = 5.83 dBm RX = 3.58 dBm
Manufacturer: LucidSound, Inc.
Importer: Information can be found at lucidsound.com
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
This device complies with FCC SAR exposure limits set forth for an uncontrolled environment The equipment can be used in close
proximity to the human body without any restrictions.
Caution!
The manufacturer is not responsible for any radio or TV interference caused by unauthorized modications to this equipment. Such
modications could void the user authority to operate the equipment.
This device complies with FCC exposure limits set forth for an uncontrolled environment
Industry Canada Statement
This device complies with Industry Canada licence-exempt RSS standard.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter
tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment should
be installed and operated with minimum distance 0.5 cm between the radiator and your body.
Cet équipement est conforme aux CNR-102 d’Industrie Canada. Cet équipement doit êtreinstallé et utilisé avec une distance mini-
male de 0.5 centimètres entre le radiateur et votrecorps. Cet émetteur ne doit pas être co-localisées ou opérant en conjonction avec
autreantenne ou émetteur. Les antennes utilisées pour cet émetteur doivent être installés etfournir une distance de séparation d’au
moins 0.5 centimètre de toute personne et doit pas être co-située ni fonctionner en conjonction avec une autre antenne ou émetteur.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should
be installed and operated with minimum distance 0 cm between the radiator and your body.
Warranty
LucidSound, Inc. warrants this product to be free from defects in materials and workmanship for the warranty period. This non-trans-
ferable, 1-year limited warranty is only to you, the rst end-user purchaser. If a defect covered by this warranty occurs AND you
provide proof of purchase, LucidSound, Inc., at its option, will repair or replace the product at no charge (excluding shipping).
The LucidSound, Inc., 1-year limited warranty is available to customers worldwide. Your sole and exclusive remedy is repair or
replacement of your LucidSound product. In no event shall LucidSound’s liability exceed the original purchase price of the product.
This warranty does not apply to: (a) normal wear and tear or abusive use; (b) industrial, professional or commercial use; (c) if the
product has been tampered with or modied. This non-transferable warranty is only valid in the region/country in which the headset
was originally purchased.
To receive warranty service, please contact us at:
lucidsound.com
(toll free) 888-661-4469
1-760-579-6969
©2019 Lucid Sound, Inc. 5939 Darwin Ct., Suite 100, Carlsbad, CA 92008 U.S.A. Microsoft, Xbox, Xbox “Sphere” Design, Xbox One,
and Windows are trademarks of the Microsoft group of companies. All other trademarks are the property of their respective owners.
The shape and design of this product are a trade dress of Lucid Sound, Inc., its subsidiaries and aliates. All rights reserved. All oth-
er product names and images are trademarks or registered trademarks of their respective owners. Made in China. Product features,
appearance and specications may be subject to change without notice. Please retain this information for future reference.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

LucidSound LS50X Mode d'emploi

Taper
Mode d'emploi

dans d''autres langues