Videotec MAXIMUS MVXT Manuel utilisateur

EN

English - Instruction manual

IT

Italiano - Manuale di istruzioni

FR

Français - Manuel d’instructions

DE

Deutsch - Bedienungsanleitung

RU

Русский - Руководство по эксплуатации

PT

Português - Manual de instruções

KO

한국어 - 지침 설명서

ENGLISH

MAXIMUS MVXT

High-spec ex-proof thermal camera in a compact design

Manual B

EN

English - Instruction manual

ENGLISH

MAXIMUS MVXT

High-spec ex-proof thermal camera in a compact design

Manual B

EN - English - Instruction manual

2 MNVCMVXTBCAM_2222_EN

Contents

ENGLISH 1

1 About this manual ....................................................................................................................3

1.1 Typographical conventions ................................................................................................................................................ 3

2 Notes on copyright and information on trademarks ............................................................3

3 Product description and type designation ............................................................................3

3.1 Product marking label .......................................................................................................................................................... 3

3.2 Model identiﬁcation.............................................................................................................................................................. 4

4 Installation ................................................................................................................................6

4.1 Range of use ............................................................................................................................................................................. 6

4.2 Connecting the power supply .......................................................................................................................................... 6

4.3 Ethernet cable connection ................................................................................................................................................. 7

4.4 I/O cable connection ............................................................................................................................................................ 7

4.4.1 Alarm and relay connections .............................................................................................................................................................. 7

4.4.1.1 Connecting an alarm with dry contact ...................................................................................................................................................................7

4.4.1.2 Relay connection ............................................................................................................................................................................................................8

5 Switching on .............................................................................................................................8

5.1 Before powering the product in an explosive atmosphere ................................................................................... 8

5.2 First start-up ............................................................................................................................................................................. 8

6 Conﬁguration............................................................................................................................9

6.1 Default IP address .................................................................................................................................................................. 9

6.2 Web interface .......................................................................................................................................................................... 9

6.2.1 First access to the web pages ............................................................................................................................................................. 9

7 Accessories ................................................................................................................................9

8 Maintenance ........................................................................................................................... 10

8.1 Firmware updating .............................................................................................................................................................. 10

8.2 Factory Default ..................................................................................................................................................................... 10

9 Troubleshooting .....................................................................................................................10

10 Information on disposal and recycling .............................................................................. 11

11 Technical data ....................................................................................................................... 12

11.1 Cameras .................................................................................................................................................................................. 12

Instruction manual - English - EN

3MNVCMVXTBCAM_2222_EN

1 About this manual

Read all the documentation supplied carefully

before installing and using this product. Keep the

manual in a convenient place for future reference.

1.1 Typographical conventions

DANGER!

High level hazard.

Risk of electric shock. Disconnect the

power supply before proceeding with any

operation, unless indicated otherwise.

DANGER!

Explosion hazard.

Read carefully to avoid danger of

explosion.

CAUTION!

Medium level hazard.

This operation is very important for the

system to function properly. Please read

the procedure described very carefully

and carry it out as instructed.

INFO

Description of system speciﬁcations.

We recommend reading this part carefully

in order to understand the subsequent

stages.

2 Notes on copyright and

information on trademarks

The mentioned names of products or companies are

trademarks or registered trademarks.

ONVIF® is a trademark of Onvif, Inc.

3 Product description and

type designation

3.1 Product marking label

See the label attached to the product.

EN - English - Instruction manual

4 MNVCMVXTBCAM_2222_EN

3.2 Model identiﬁcation

MAXIMUS MVXT  CONFIGURATION OPTIONS WITH CABLE GLAND AND ARMOURED CABLE

Voltage Thermal camera Radiometry Connections Model Frequency

MVXT 2 12-24Vdc/

24Vac

Q Thermal camera 9mm, 336x256 0 Thermal camera with

radiometric functions

S A Cable gland Ex d 3/4"

NPT and 4m (13ft)

armoured cable

Z00 T5 -60°C/+65°C B - 7.5Hz

M Thermal camera 13mm, 336x256 R Thermal camera with

advanced radiometric

functions

B Cable gland Ex d 3/4"

NPT and 10m (32.8ft)

armoured cable

02 T6 -60°C/+55°C

H 30Hz

Z Thermal camera 19mm, 336x256

L Thermal camera 25mm, 336x256

I Thermal camera 35mm, 336x256

J Thermal camera 50mm, 336x256

P Thermal camera 60mm, 336x256

H Thermal camera 9mm, 640x512

G Thermal camera 13mm, 640x512

U Thermal camera 19mm, 640x512

E Thermal camera 25mm, 640x512

D Thermal camera 35mm, 640x512

W Thermal camera 50mm, 640x512

K Thermal camera 60mm, 640x512

Tab. 1

Instruction manual - English - EN

5MNVCMVXTBCAM_2222_EN

MAXIMUS MVXT  CONFIGURATION OPTIONS WITH CABLE TAIL FOR INSTALLATION WITH CONDUIT

Voltage Thermal camera Radiometry Connections Model Frequency

MVXT 2 12-24Vdc/

24Vac

Q Thermal camera 9mm, 336x256 0 Thermal camera with

radiometric functions

S F 4m (13ft) cable tail Z01 T5 -50°C/+65°C B - 7.5Hz

M Thermal camera 13mm, 336x256 R Thermal camera with

advanced radiometric

functions

G 10m (32.8ft) cable tail

03 T6 -50°C/+55°C

H 30Hz

Z Thermal camera 19mm, 336x256

L Thermal camera 25mm, 336x256

I Thermal camera 35mm, 336x256

J Thermal camera 50mm, 336x256

P Thermal camera 60mm, 336x256

H Thermal camera 9mm, 640x512

G Thermal camera 13mm, 640x512

U Thermal camera 19mm, 640x512

E Thermal camera 25mm, 640x512

D Thermal camera 35mm, 640x512

W Thermal camera 50mm, 640x512

K Thermal camera 60mm, 640x512

Tab. 2

EN - English - Instruction manual

6 MNVCMVXTBCAM_2222_EN

4 Installation

CAUTION! Device installation and

maintaining must be performed by

specialist technical staﬀ only.

The external multipolar cable shield

(armour) must be earthed.

All disconnected wires must be electrically

isolated.

Before installation of the version with

multipolar cable, ensure correct curvature

of the cable is guaranteed (at least

200mm/7.8in).

4.1 Range of use

For indoors and outdoors installation.

Operating temperature:

• Continuous working: from -50°C (-58°F) up to

+65°C (149°F).

• Cold start: up to -40°C (-40°F).

Relative humidity: from 10% up to 95% (no

condensation).

4.2 Connecting the power supply

Electrical connections must be performed

with the power supply disconnected and

the circuit-breaker open.

When commencing installation make

sure that the speciﬁcations for the power

supply for the installation correspond with

those required by the device.

Check that the power supply is adequately

dimensioned.

The device can be provided with diﬀerent power

supply voltages. The power supply voltage is

indicated on the product identiﬁcation label (3.1

Product marking label, page 3).

Perform the connections following the instructions

reported in the table .

CONNECTING THE POWER SUPPLY

Power supply 24Vac/ 24Vdc/ 12Vdc

Colour/Number Description

24Vac 24Vdc/12Vdc

Black/1 ~V+

Black/2 ~V-

Yellow-Green

Tab. 3

Instruction manual - English - EN

7MNVCMVXTBCAM_2222_EN

4.3 Ethernet cable connection

The Ethernet cable shield must always be

earthed via the connector. Always use a

shielded RJ45 connector.

Use of Ethernet cables with the following

characteristics is highly recommended:

• STP (shielded)

• Category 5E

• RJ45 connector (crimped in compliance with

standard TIA/EIA-568-B)

The product can be directly connected to an

Ethernet switch.

ETHERNET CABLE CONNECTION

Pin number Core colour

1Orange-White

2Orange

3Green-White

4Blue

5Blue-White

6Green

7Brown-White

8Brown

Tab. 4

The example below shows a typical installation.

Switch

Personal

Computer

Fig. 1

4.4 I/O cable connection

CAUTION! TNV-1 installation type. The

installation is type TNV-1, do not connect it

to SELV circuits.

The shielding of the I/O cable must be

grounded.

I/O CABLE CONNECTION

Colour Function

White RS-485 A (+)

Yellow RS-485 B (-)

Pink Relay 1, Terminal A

Blue Relay 1, Terminal B

Brown Alarm/Digital input

Green GND/Common alarm

Grey Reset

Tab. 5

4.4.1 Alarm and relay connections

The unit is equipped with the alarms and relays

indicated in the table (Tab. 5, page 7).

4.4.1.1 Connecting an alarm with dry

contact

In case of free contact alarm make the connection as

shown in the ﬁgure.

AL COM

Dry contact

Fig. 2 AL: Alarm. COM: Common alarm.

Clean contact of the alarm can be set NO (normally

open) or NC (normally closed) using the web

interface.

EN - English - Instruction manual

8 MNVCMVXTBCAM_2222_EN

4.4.1.2 Relay connection

Relay operating speciﬁcations.

• Working voltage: 30Vac max or 60Vdc

max.

• Current: 1A max.

Use suitable cable sections: from 0.2mm²

(30AWG) up to 1mm² (16AWG).

Due to the absence of polarity, both terminals of the

same relay can be connected either to alternating or

direct current voltages.

5 Switching on

Do not turn on the unit when the ambient

temperature is lower than indicated: -40°C

(-40°F).

The full functionality of the product is

guaranteed from the following ambient

temperature: -40°C (-40°F).

The automatic pre-heating procedure

(De-Ice) activates for 2 hours if on device

switch on an ambient temperature is

detected under -10°C (14°F). The procedure

is necessary to guarantee correct

operation of the devices even at low

temperatures.

5.1 Before powering the product

in an explosive atmosphere

Make sure that the unit and other

components of the installation are closed

so that it is impossible to come into

contact with live parts.

Make sure that the device has been

connected to an earth link as described.

Ensure the rear cover plate is correctly

closed.

Ensure the product is correctly closed.

Ensure that the sealing of cable entry

systems (if any) has been performed

properly and the time of glue hardening

has been observed.

Make sure that all parts are fastened down

ﬁrmly and safely.

5.2 First start-up

Ensure the unit and the other components

of the system are appropriately closed to

prevent contact with live parts.

Make sure that all parts are fastened down

ﬁrmly and safely.

The unit is switched on by connecting the power

supply.

To switch oﬀ the unit disconnect the power.

Instruction manual - English - EN

9MNVCMVXTBCAM_2222_EN

6 Conﬁguration

6.1 Default IP address

The unit is conﬁgured to obtain an IP

address from a DHCP server.

The IP address acquired via DHCP is visible in the

DHCP server log ﬁle.

If the DHCP server is not available, the unit

automatically conﬁgures itself with a self-generated

IP address in the 169.254.x.x/16 subnet. Conﬁguring

the IP address of the PC as belonging to the same

subnet (example: IP address: 169.254.1.1, subnet

mask: 255.255.0.0).

Use an ONVIF compliant VMS or a network sniﬀer to

ﬁnd the IP address of the device (IP scan utility).

6.2 Web interface

Browsers supported (the latest version):

Microsoft Edge, Google Chrome, Mozilla

Firefox.

6.2.1 First access to the web pages

The ﬁrst operation in conﬁguring the device consists

in connecting to the web interface.

To access the web interface of the product, simply

use a browser to connect to http://ip_address.

On ﬁrst access, the Home page will be displayed.

To conﬁgure the web interface, consult the manual

relating to the ﬁrmware version installed, available

on the product web page of the website www.

videotec.com.

7 Accessories

For further details on conﬁguration and

use, refer to the manual of the relevant

accessory or support.

EN - English - Instruction manual

10 MNVCMVXTBCAM_2222_EN

8 Maintenance

The pre-installed camera can only be

replaced with one of the same brand and

model.

Read the product Manual A before

performing any operation.

Please provide the device serial number when

requesting any replacement parts.

8.1 Firmware updating

Firmware upgrading can be carried out

directly on the web interface.

If necessary it is possible to update the device

ﬁrmware.

For further information please contact the VIDEOTEC

service center.

8.2 Factory Default

It is possible to reset to the factory default settings.

Execute the procedure below:

• Switch oﬀ the unit.

• Connect the I/O cable grey and green wires (Tab.

5, page 7).

• Power the unit.

• Wait 30 seconds.

• Disconnect the previously connected grey and

green wires.

• Wait for 2 minutes.

• Switch oﬀ the unit.

• Power the unit.

Once the factory default procedure has

ﬁnished, you need to conﬁgure the unit

as described in chapter: 6.1 Default IP

address, page 9.

9 Troubleshooting

Contact an authorised support centre if

the problems persist or you have any other

issues that are not described here.

Read the product Manual A before

performing any operation.

PROBLEM Video streaming is not

visible.

CAUSE Incorrect IP address settings.

SOLUTION Check the device IP address

and the conﬁguration of the

computer network card.

CAUSE Automatic preheating

procedure (De-Ice) in progress.

SOLUTION Wait until the end of the

pre-heating procedure. If the

ambient temperature is too low

the unit will remain blocked.

Instruction manual - English - EN

11MNVCMVXTBCAM_2222_EN

10 Information on disposal

and recycling

The European Directive 2012/19/EU on Waste

Electrical and Electronic Equipment (WEEE)

mandates that these devices should not be disposed

of in the normal ﬂow of municipal solid waste, but

they should be collected separately in order to

optimize the recovery stream and recycling of the

materials that they contain and to reduce the impact

on human health and the environment due to the

presence of potentially hazardous substances.

The symbol of the crossed out bin is

marked on all products to remember this.

The waste may be delivered to appropriate

collection centers, or may be delivered free of

charge to the distributor where you purchased

the equipment at the time of purchase of a new

equivalent or without obligation to a new purchase

for equipment with size smaller than 25cm (9.8in).

For more information on proper disposal of these

devices, you can contact the responsible public

service.

EN - English - Instruction manual

12 MNVCMVXTBCAM_2222_EN

11 Technical data

For the technical data of the housing, consult Manual A of the product.

11.1 Cameras

THERMAL CAMERAS RESOLUTION 336X256

Lens 9mm 13mm 19mm 25mm 35mm 50mm 60mm

VOx microbolometer sensor not cooled √√√√√√√

Interpolated resolution 720x480 720x480 720x480 720x480 720x480 720x480 720x480

Pixel dimensions 17μm 17μm 17μm 17μm 17μm 17μm 17μm

Spectral response - long wave infrared (LWIR)

from 7.5μm to 13.5μm from 7.5μm to 13.5μm from 7.5μm to 13.5μm from 7.5μm to 13.5μm from 7.5μm to 13.5μm from 7.5μm to 13.5μm from 7.5μm to 13.5μm

Internal shutter (only for sensor compensation) Video stop <1s Video stop <1s Video stop <1s Video stop <1s Video stop <1s Video stop <1s Video stop <1s

Digital Detail Enhancement (DDE) √√√√√√√

Digital Zoom 2x, 4x 2x, 4x 2x, 4x 2x, 4x 2x, 4x 2x, 4x 2x, 4x

Image updating frequency 7.5f ps 7.5fps 7. 5fps 7. 5fps 7. 5fps 7. 5fps 7.5fps

Image updating high frequency 30fps 30fps 30fps 30fps 30fps 30fps 30fps

Scene range (High Gain) -40°C ÷ +160°C

(-40°F ÷ +320°F)

-40°C ÷ +160°C

(-40°F ÷ +320°F)

-40°C ÷ +160°C

(-40°F ÷ +320°F)

-40°C ÷ +160°C

(-40°F ÷ +320°F)

-40°C ÷ +160°C

(-40°F ÷ +320°F)

-40°C ÷ +160°C

(-40°F ÷ +320°F)

-40°C ÷ +160°C

(-40°F ÷ +320°F)

Scene range (Low Gain) -40°C ÷ +550°C

(-40°F ÷ +1022°F)

-40°C ÷ +550°C

(-40°F ÷ +1022°F)

-40°C ÷ +550°C

(-40°F ÷ +1022°F)

-40°C ÷ +550°C

(-40°F ÷ +1022°F)

-40°C ÷ +550°C

(-40°F ÷ +1022°F)

-40°C ÷ +550°C

(-40°F ÷ +1022°F)

-40°C ÷ +550°C

(-40°F ÷ +1022°F)

Horizontal ﬁeld of view (HFOV) 35° 25° 17° 13° 9.3° 6.5° 5.5°

Vertical ﬁeld of view (VFOV) 27° 19° 13° 10° 7.1° 5° 4.2°

f-number f/1.25 f/1.25 f/1.25 f/1.1 f/1.2 f/1.2 f/1.25

Thermal sensitivity (NETD), thermal camera with radiometric

functions

<50mK at f/1.0 <50mK at f/1.0 <50mK at f/1.0 <50mK at f/1.0 <50mK at f/1.0 <50mK at f/1.0 <50mK at f/1.0

Thermal sensitivity (NETD), thermal camera with advanced

radiometric functions

<30mK at f/1.0 <30mK at f/1.0 <30mK at f/1.0 <30mK at f/1.0 <30mK at f/1.0 <30mK at f/1.0 <30mK at f/1.0

Person (detection / recognition / identiﬁcation) 285m / 71m / 36m

(935ft / 233ft /

118ft)

440m / 112m /

56m (1443ft /

2368ft / 183ft)

640m / 160m /

80m (2099ft /

524ft / 262ft)

930m / 230m /

116m (3051ft /

754ft / 380ft)

1280m / 320m /

160m (4199ft /

1050ft / 525ft)

1700m / 430m /

215m (5577ft /

1410ft / 715ft)

2000m / 510m

/ 255m (6561ft /

1673ft / 836ft)

Car (detection / recognition / identiﬁcation) 880m / 220m /

108m (2887ft /

722ft / 354ft)

1340m / 340m

/ 170m (4396ft /

1115f t / 557ft)

1950m / 500m

/ 250m (6397ft/

1640ft/ 820ft)

2800m / 710m /

360m (9186ft /

2329ft / 1181ft)

3850m / 950m /

295m (12631ft /

3116ft / 967ft)

5100m / 1320m /

660m (16732ft /

4330ft / 2165ft)

6000m / 1560m /

780m (19685ft /

5118ft / 2559ft)

Tab. 6 Radiometric analysis does not aﬀect camera performance.

Instruction manual - English - EN

13MNVCMVXTBCAM_2222_EN

THERMAL CAMERAS RESOLUTION 640X512

Lens 9mm 13mm 19mm 25mm 35mm 50mm 60mm

VOx microbolometer sensor not cooled √√√√√√√

Interpolated resolution 720x480 720x480 720x480 720x480 720x480 720x480 720x480

Pixel dimensions 17μm 17μm 17μm 17μm 17μm 17μm 17μm

Spectral response - long wave infrared (LWIR) from 7.5μm to

13.5μm

from 7.5μm to

13.5μm

from 7.5μm to

13.5μm

from 7.5μm to

13.5μm

from 7.5μm to

13.5μm

from 7.5μm to

13.5μm

from 7.5μm to

13.5μm

Internal shutter (only for sensor compensation) Video stop <1s Video stop <1s Video stop <1s Video stop <1s Video stop <1s Video stop <1s Video stop <1s

Digital Detail Enhancement (DDE) √√√√√√√

Digital Zoom 2x, 4x, 8x 2x, 4x, 8x 2x, 4x, 8x 2x, 4x, 8x 2x, 4x, 8x 2x, 4x, 8x 2x, 4x, 8x

Image updating frequency 7.5f ps 7.5fps 7. 5fps 7. 5fps 7. 5fps 7. 5fps 7.5fps

Image updating high frequency 30fps 30fps 30fps 30fps 30fps 30fps 30fps

Scene range (High Gain) -40°C ÷ +160°C

(-40°F ÷ +320°F)

-40°C ÷ +160°C

(-40°F ÷ +320°F)

-40°C ÷ +160°C

(-40°F ÷ +320°F)

-40°C ÷ +160°C

(-40°F ÷ +320°F)

-40°C ÷ +160°C

(-40°F ÷ +320°F)

-40°C ÷ +160°C

(-40°F ÷ +320°F)

-40°C ÷ +160°C

(-40°F ÷ +320°F)

Scene range (Low Gain) -40°C ÷ +550°C

(-40°F ÷ +1022°F)

-40°C ÷ +550°C

(-40°F ÷ +1022°F)

-40°C ÷ +550°C

(-40°F ÷ +1022°F)

-40°C ÷ +550°C

(-40°F ÷ +1022°F)

-40°C ÷ +550°C

(-40°F ÷ +1022°F)

-40°C ÷ +550°C

(-40°F ÷ +1022°F)

-40°C ÷ +550°C

(-40°F ÷ +1022°F)

Horizontal ﬁeld of view (HFOV) 69° 45° 32° 25° 18° 12.4° 10.4°

Vertical ﬁeld of view (VFOV) 56° 37° 26° 20° 14° 9.9° 8.3°

f-number f/1.4 f/1.25 f/1.25 f/1.1 f/1.2 f/1.2 f/1.25

Thermal sensitivity (NETD), thermal camera with radiome-

tric functions

<50mK at f/1.0 <50mK at f/1.0 <50mK at f/1.0 <50mK at f/1.0 <50mK at f/1.0 <50mK at f/1.0 <50mK at f/1.0

Thermal sensitivity (NETD), thermal camera with advanced

radiometric functions

<30mK at f/1.0 <30mK at f/1.0 <30mK at f/1.0 <30mK at f/1.0 <30mK at f/1.0 <30mK at f/1.0 <30mK at f/1.0

Person (detection / recognition / identiﬁcation) 250m / 63m / 31m

(820ft / 207ft /

102ft)

390m / 95m / 47m

(1280ft / 312ft /

154ft)

570m / 144m /

72m (1870 / 472 /

236ft)

820m / 210m /

104m (2690ft /

689ft / 341ft)

1140m / 280m /

142m (3740ft /

919ft / 466ft)

1500m / 380m

/ 190m (4921ft /

1247ft / 623ft)

1750m / 450m /

225m (5741ft /

1476ft / 738ft)

Car (detection / recognition / identiﬁcation) 720m / 175m

/88m (2362 / 574

/ 289ft)

1080m / 275m /

140m (3543ft /

902ft / 459ft)

1550m / 400m /

200m (5085ft /

1312ft / 656ft)

2200m / 580m /

290m (7218ft /

1903ft / 951ft)

3000m / 800m /

200m (9843ft /

2625ft / 656ft)

3900m / 1060m

/ 540m (12795ft /

3478ft / 1772)

4500m / 1240m /

640m (14764ft /

4068ft / 2100ft)

Tab. 7 Radiometric analysis does not aﬀect camera performance.

MNVCMVXTBCAM_2222_EN

Headquarters Italy VIDEOTEC s.r.l.

Via Friuli, 6 - I-36015 Schio (VI) - Italy

Tel. +39 0445 697411 - Fax +39 0445 697414

Email: [email protected]

www.videotec.com

IT

Italiano - Manuale di istruzioni

ITALIANO

MAXIMUS MVXT

Telecamera termica antideﬂagrante ad alte prestazioni dal design compatto

Manuale B

IT - Italiano - Manuale di istruzioni

2 MNVCMVXTBCAM_2222_IT

Sommario

ITALIANO 1

1 Informazioni sul presente manuale........................................................................................3

1.1 Convenzioni tipograﬁche .................................................................................................................................................... 3

2 Note sul copyright e informazioni sui marchi commerciali .................................................3

3 Descrizione e designazione del prodotto ..............................................................................3

3.1 Etichetta di marcatura del prodotto ............................................................................................................................... 3

3.2 Identiﬁcazione del modello ............................................................................................................................................... 4

4 Installazione .............................................................................................................................6

4.1 Campo di utilizzo .................................................................................................................................................................... 6

4.2 Collegamento della linea di alimentazione ................................................................................................................. 6

4.3 Collegamento del cavo Ethernet ..................................................................................................................................... 7

4.4 Collegamento dei cavi I/O .................................................................................................................................................. 7

4.4.1 Collegamento degli allarmi e dei relè .............................................................................................................................................7

4.4.1.1 Collegamento dell'allarme con contatto pulito..................................................................................................................................................7

4.4.1.2 Collegamento del relè ..................................................................................................................................................................................................8

5 Accensione ................................................................................................................................ 8

5.1 Prima di alimentare il prodotto in atmosfera esplosiva ........................................................................................... 8

5.2 Prima accensione ................................................................................................................................................................... 8

6 Conﬁgurazione ......................................................................................................................... 9

6.1 Indirizzo IP di default ............................................................................................................................................................ 9

6.2 Interfaccia web ........................................................................................................................................................................ 9

6.2.1 Primo accesso alle pagine web .......................................................................................................................................................... 9

7 Accessori ...................................................................................................................................9

8 Manutenzione ........................................................................................................................10

8.1 Aggiornamento del ﬁrmware .......................................................................................................................................... 10

8.2 Factory Default ..................................................................................................................................................................... 10

9 Risoluzione dei problemi.......................................................................................................10

10 Informazioni sullo smaltimento e il riciclo ........................................................................ 11

11 Dati tecnici ............................................................................................................................ 12

11.1 Telecamere ............................................................................................................................................................................ 12

Manuale di istruzioni - Italiano - IT

3MNVCMVXTBCAM_2222_IT

1 Informazioni sul presente

manuale

Prima di installare e utilizzare questo prodotto

leggere attentamente tutta la documentazione

fornita. Tenere il manuale a portata di mano per

consultazioni successive.

1.1 Convenzioni tipograﬁche

PERICOLO!

Pericolosità elevata.

Rischio di scosse elettriche. Prima di

eseguire qualsiasi operazione assicurarsi

di togliere tensione al prodotto, salvo

diversa indicazione.

PERICOLO!

Pericolo di esplosione.

Leggere attentamente per evitare pericoli

di esplosione.

ATTENZIONE!

Pericolosità media.

L'operazione è molto importante per

il corretto funzionamento del sistema.

Si prega di leggere attentamente la

procedura indicata e di eseguirla secondo

le modalità previste.

INFO

Descrizione delle caratteristiche del

sistema.

Si consiglia di leggere attentamente per

comprendere le fasi successive.

2 Note sul copyright e

informazioni sui marchi

commerciali

I nomi di prodotto o di aziende citati sono marchi

commerciali o marchi commerciali registrati

appartenenti alle rispettive società.

ONVIF® è un marchio di proprietà di Onvif, Inc.

3 Descrizione e

designazione del prodotto

3.1 Etichetta di marcatura del

prodotto

Vedere l’etichetta posta sul prodotto.

IT - Italiano - Manuale di istruzioni

4 MNVCMVXTBCAM_2222_IT

3.2 Identiﬁcazione del modello

MAXIMUS MVXT  OPZIONI DI CONFIGURAZIONE CON PRESSACAVO E CAVO ARMATO

Voltaggio Telecamera termica Radiometria Connessioni Modello Frequenza

MVXT 2 12-24Vdc/

24Vac

Q Telecamera termica 9mm, 336x256 0 Telecamera termica con

funzioni radiometriche

S A Pressacavo Ex d 3/4"

NPT e cavo armato da

4m

Z00 T5 -60°C/+65°C B - 7.5Hz

M Telecamera termica 13mm, 336x256 R Telecamera termica con

funzioni radiometriche

avanzate

B Pressacavo Ex d 3/4"

NPT e cavo armato da

10m

02 T6 -60°C/+55°C

H 30Hz

Z Telecamera termica 19mm, 336x256

L Telecamera termica 25mm, 336x256

I Telecamera termica 35mm, 336x256

J Telecamera termica 50mm, 336x256

P Telecamera termica 60mm, 336x256

H Telecamera termica 9mm, 640x512

G Telecamera termica 13mm, 640x512

U Telecamera termica 19mm, 640x512

E Telecamera termica 25mm, 640x512

D Telecamera termica 35mm, 640x512

W Telecamera termica 50mm, 640x512

K Telecamera termica 60mm, 640x512

Tab. 1

La page charge ...

Videotec MAXIMUS MVXT Manuel utilisateur

Videotec MAXIMUS MVXT Manuel utilisateur

dans d''autres langues

Documents connexes