Maytag MED5100DW0 Le manuel du propriétaire

Catégorie
Sèche-linge électriques
Taper
Le manuel du propriétaire
HEU_
Guide
tionet d'entretien
ICDRYER
r
Para obtener acceso
al Manual de uso y
cuidado en espanol, o para
obtener informaci6n adicional
acerca de su producto, visite:
www.maytag.com
If you have any problems or questions, visit us at www.maytag.com
Pour tout probleme ou question, consulter www.maytag.ca
W10596022B
W10596023B - SP
TABLEOFCONTENTS
DRYER SAFETY .......................................................................................2
ACCESSORIES .......................................................................................4
CHECK YOUR VENT SYSTEM FOR GOOD AIR FLOW ............5
CONTROL PANEL AND FEATURES .................................................6
CYCLE GUIDE ..........................................................................................8
USING YOUR DRYER ........................................................................10
CYCLE STATUS INDICATORS ..........................................................12
ADDITIONAL FEATURES ..................................................................12
DRYER CARE ........................................................................................13
TROUBLESHOOTING ........................................................................15
WARRANTY ...........................................................................................18
ASSISTANCE OR SERVICE .............................................Back Cover
TABLEDEMATI#RES
SECURITE DE LA SECHEUSE ........................................................19
ACCESSOIRES ....................................................................................21
VE_RIFICATIOND'UNE CIRCULATION D'AIR ADEQUATE
POUR LE SYSTEME D'EVACUATION ............................................22
TABLEAU DE COMMANDE ET CARACTERISTIQUES ............23
GUIDE DE PROGRAMMES .............................................................26
UTILISATION DE LA SECHEUSE ....................................................28
TEMOINS LUMINEUX DE PROGRAMME ...................................30
CARACTERISTIQU ES SU PPLEM ENTAIRES...............................31
ENTRETIEN DE LA SECHEUSE ......................................................32
DEPANNAGE .........................................................................................34
GARANTIE ..............................................................................................38
ASSISTANCE OU SERVICE .................................Couverture arriere
DRYERSAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
®
You can be killed or seriously injured if you don't immediately
follow instructions,
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
- "Risk of Fire"
- Clothes dryer installation must be performed by a qualified installer.
- install the clothes dryer according to the manufacturer's instructions and local codes.
- Do not install a clothes dryer with flexible plastic venting materials or flexible metal
(foil type) duct. if flexible metal duct is installed, it must be of a specific type identified
by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting
materials are known to collapse, be easily crushed, and trap lint. These conditions will
obstruct clothes dryer airflow and increase the risk of fire.
- To reduce the risk of severe injury or death, follow all installation instructions.
- Save these instructions.
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other
reproductive harm.
In the State of Massachusetts, the following installation instructions apply:
[] Installations and repairs must be performed by a qualified or licensed contractor, plumber, or gasfitter qualified or licensed by
the State of Massachusetts.
[] If using a ball valve, it shall be a T-handle type.
[] A flexible gas connector, when used, must not exceed 3 feet.
WARNING: For your safety, the information in this manual must be followed to minimize
the risk of fire or explosion, or to prevent property damage, personal injury, or death.
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this
or any other appliance.
- WHAT TO DO IF YOU SMELL GAS:
Do not try to light any appliance.
Do not touch any electrical switch; do not use any phone in your building.
e Clear the room, building, or area of all occupants.
Immediately call your gas supplier from a neighbor's phone. Follow the gas supplier's
instructions.
® If you cannot reach your gas supplier, call the fire department.
- installation and service must be performed by a qualified installer, service agency, or
the gas supplier.
WARNING: Gas leaks cannot always be detected by smell.
Gas suppliers recommend that you use a gas detector approved by UL or CSA.
For more information, contact your gas supplier.
If a gas leak is detected, follow the "What to do if you smell gas" instructions.
I
iMPORTANT: The gas installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas
Code, ANSI Z223.1iNFPA 54.
The dryer must be electrically grounded in accordance with local codes, or in the absence of local codes, with the National
Electrical Code, ANSl/NFPA 70.
iMPORTANT: When discarding or storing your old clothes dryer, remove the door.
iMPORTANT SAFETY iNSTRUCTIONS
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,
including the following:
[] Read all instructions before using the dryer.
[] Do not place items exposed to cooking oils in your dryer.
Items contaminated with cooking oils may contribute to
a chemical reaction that could cause a load to catch fire.
[] Do not dry articles that have been previously cleaned in,
washed in, soaked in, or spotted with gasoline, dry=
cleaning solvents, or other flammable or explosive
substances as they give off vapors that could ignite or
explode.
[] Do not allow children to play on or in the dryer. Close
supervision of children is necessary when the dryer is
used near children.
[] Before the dryer is removed from service or discarded,
remove the door to the drying compartment.
[] Do not reach into the dryer if the drum is moving.
[] Do not install or store the dryer where it will be exposed
to the weather.
[] Do not tamper with controls.
[] Do not repair or replace any part of the dryer or attempt
any servicing unless specifically recommended in this
Use and Care Guide or in published user-repair
instructions that you understand and have the skills to
carry out.
[] Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
[] Do not use heat to dry articles containing foam rubber or
similarly textured rubber-like materials.
[] Clean lint screen before or after each load.
[] Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint, dust,
and dirt.
[] The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
[] See "Electrical Requirements" located in the installation
instructions for grounding instructions.
SAVE THESE iNSTRUCTIONS
ACCESSORIES
Customize your new washer and dryer with the following
genuine Maytag accessories. For more information on options
and ordering, contact your dealer, call us at 1-800-901-2042,
or visit: www.maytag.com/accessories.
In Canada, call 1-800-807-6777, or visit: www.maytag.ca
15" Pedestal
Color-matched pedestals raise the washer and
dryer to a more comfortable working height.
The large drawer provides convenient storage.
Stack Kit
Ifspace is at a premium, the stack kit allows
the dryer to be installed on top of the washer.
Drying Rack
The Drying Rack provides a
stationary drying surface for items
such as sweaters and tennis shoes.
See the "Additional Features"
section for more information.
4
CHECKYOURVENTSYSTEMFORGOODAiR FLOW
Fire Hazard
Use a heavy metal vent,
Do not use a plastic vent.
Do not use a metal foil vent.
Failure to follow these instructions can result in death
or fire.
Good air flow
Along with heat, dryers require good air flow to efficiently
dry laundry. Proper venting will reduce your drying times and
improve your energy savings. See Installation Instructions.
The venting system attached to the dryer plays a big role
in good air flow.
Service calls caused by improper venting are not covered by
the warranty and will be paid by the customer, regardless of
who installed the dryer.
Maintain good air flow by:
[] Cleaning your lint screen before each load.
[] Replace plastic or foil vent material
with 4" (102 mm) diameter heavy, rigid
vent material.
[] Use the shortest length of vent possible.
[] Use no more than four 90 ° elbows in a vent system;
each bend and curve reduces air flow.
Better_
[]
[]
[]
Remove lint and debris from the exhaust hood.
Remove lint from the entire length of the vent system
at least every 2 years. When cleaning is complete, be
sure to follow the Installation Instructions supplied with
your dryer for final product check.
Clear away items from the front of the dryer.
Use Sensor cycles for better fabric care and energy savings
Use the Sensor Cycles to provide the most energy savings and enhanced fabric care from the dryer. During Sensor Cycles, drying air
temperature and moisture level are sensed in the load. This sensing occurs throughout the drying cycle and the dryer shuts off when the
load reaches the selected dryness. Use the NORMAL dryness level to provide optimal energy savings.
With Timed Dry, the dryer runs the amount of time set and sometimes results in shrinkage, wrinkling, and static due to over-drying.
Use Timed Dry for the occasional damp load that needs a little more drying time or when using the drying rack.
Tips for getting the best performance from your steam dryer (on some models)
[] Results may vary depending on fabric. 1000/o cotton [] Cycles that use steam are not recommended for items that
garments with wrinkle-free finish may yield better results than have been starched. Wash any starched or new garments prior
those without. 1000/0 cotton items may require additional to using cycles that use steam.
touching up after cycles that use steam. [] The Refresh Cycle is best for smoothing out wrinkles
Use of fabric softener sheet is not recommended with cycles and reducing odors from loads consisting of dry items of
that use steam. It may cause temporary staining on clothes, wrinkle-free cotton, cotton-polyester blend, common knits,
and synthetics.
[]
CONTROLPANELAND FEATURES
Not all features and cycles are available on all models.
NOTE: The control panel features a sensitive surface that responds
to a light touch of your finger. To ensure your selections are registered,
touch the control panel with your finger tip, not your fingernail. When
selecting a setting or option, simply touch its name.
O POWER/CANCEL
Touch to turn the dryer on and off. Touch to stop/cancel
a cycle at any time.
O
CYCLE CONTROL KNOB
Turn the knob to select a cycle for your laundry load. Sensor
Cycles are Heavy Duty, Normal, Delicates, Sanitize (on some
models), Bedding (on some models), and Wrinkle Control
(on some models). Timed Cycles are Timed Dry and Rapid
Dry. The Steam Cycle (on some models) is Refresh. See
"Cycle Guide" for detailed descriptions of cycles.
START/PAUSE
Touch and hold until the LED comes on to start a cycle,
or touch once while a cycle is in process to pause it.
O
LED DISPLAY AND SETTINGS
When you select a cycle, its settings will light up and the
Estimated Cycle Time (for Sensor Cycles) or actual time
remaining (for Timed Cycles) will be displayed. On 2-digit
displays, for times longer than 99 minutes, hours will be
displayed followed by minutes.
See "Cycle Guide" for available settings on each cycle.
Not all settings are available with all cycles.
-/+ (Timed Dry Adjust)
Touch "+" or "-" with Timed Cycles to increase or
decrease the length of a Timed Dry or Rapid Dry cycle.
Temperature
When using Timed Cycles or Refresh, you may select a
dry temperature based on the type of load you are drying.
Use the warmest setting safe for the garments in the load.
Follow garment label instructions.
NOTE: Sensor Cycles use a preset temperature that is
not adjustable.
Dryness Level
When using Sensor Cycles (except for the Sanitize cycle),
you may select a Dryness Level based on the type of load
you are drying.
NOTE: Dryness Level is for use with Sensor Cycles only.
Wrinkle Prevent
If you will be unable to remove a load immediately, touch
Wrinkle Prevent to add up to 140 minutes of periodic
tumbling to help reduce wrinkling. On some cycles, you
may select the "With Steam" setting to add a short steam
cycle after 60 minutes to help smooth out wrinkles.
Energy Saver
Touch to activate the Energy Saver option, which allows
you to increase your energy savings by using a slightly
lower heat level. For automatic cycles, Energy Saver will
increase drying times by approximately 40 minutes; the
LED Display will reflect this time.
Energy Saver will default on for Normal. For optimal energy,
turn on the Energy Saver option. For optimal time, turn off
the Energy Saver option.
O
O
OPTIONS
Use to select available options for your dryer. Not all cycles
and options are available on all models.
Drum Light
Touch to turn the LED drum light on or off. The light
will also turn on when the door is open, and turn off
automatically after about 5 minutes.
Reduce Static
Touch to add the Reduce Static option to selected
Sensor cycles (see "Cycle Guide"). The dryer will
automatically tumble, pause, and introduce a small amount
of moisture into the load to help reduce static. This option
acids approximately 8 minutes to the total cycle time.
Steam Boost
Steam Boost adds steam to the end of the Heavy Duty,
Bedding, or Normal cycle to help smooth wrinkles. Steam
Boost can be used with High or Medium heat settings.
This option acids approximately 15 minutes to the total
cycle time.
Wrinkle Prevent
If you will be unable to remove a load immediately, touch
Wrinkle Prevent to add up to 140 minutes of periodic
tumbling to help reduce wrinkling. On some cycles, you
may select the "With Steam" setting to add a short steam
cycle after 60 minutes to help smooth out wrinkles.
Damp Dry Signal
Touch to select the Damp Dry Signal. When selected, a
series of beeps will sound when the load is damp, but not
completely dry. This will allow you to take clothes out of
the load that do not need to dry completely. This option
is available on Heavy Duty, Normal, Wrinkle Control,
Bedding, and Delicates cycles. The Damp Dry Signal is
selected as a default for the Bedding cycle, as a reminder
to manually reposifion bedding loads midway through the
cycle.
Cycle Signal
Use this to turn the signal indicating the end of a drying
cycle on or off.
NOTE: You may also turn off the tones that sound when
a feature, setting, or option is touched. Touch and hold
Cycle Signal for about one second to turn sounds on
or off.
Control Lock
Use to lock the controls of the dryer and avoid
an accidental change in cycle options or preferences
during a drying cycle.
Touch and hold CONTROL LOCK for 3 seconds to lock
or unlock the controls of the dryer. During this time, the
LED Display will count clown 3-2-1. Once the controls
are locked, the LED Display will display "Lc" or "Loc:'
NOTE: The Control Lock function may be enabled when
recovering from a power failure. To unlock the control,
touch and hold CONTROL LOCK for at least 3 seconds.
CYCLE STATUS LIGHTS
The indicator bar on the right side of the control will let you
know what stage of the drying cycle is in process. For more
information on each stage, see "Cycle Status Indicators"
CYCLEGUIDE- SENSORCYCLES
Settings and options shown in bold are default settings for that cycle.
if settings are changed, the new settings will be remembered, if there is a power failure, settings will return to the default.
Not all features and cycles are available on all models.
Not all settings and options are available on each cycle.
Use Sensor Cycles for better fabric care and energy savings
The dryer senses moisture in the load or air temperature and shuts off when the load reaches the selected dryness level.
Use the NORMAL dryness [eve[ to provide optimal energ
Cycle:
Heavy High
Duty
temstoary:
Heavyweight items
such as towels or
heavy work clothes
Work clothes, casual
wear, mixed cottons,
sheets, corduroys
Shirts, blouses,
permanent press,
synthetics,
lightweight items
Undergarments,
blouses, lingerie,
performance wear
Large loads
of heavyweight
items
Normal
Wrinkle Control
De[icates
Sanitize
Bedding
Drying
Temperature:
Medium
Low
Extra Low
High
Medium
savings.
Dryness
Leveh
More
Normal
Less
More
Normal
Less
More
Normal
Less
More
Normal
Less
40
78
Jackets, comforters,
pillows
33
28
Op i n", Cyc,eDetai,s:
Damp Dry Signal i_ Offers stepped drying starting
Wrinkle Prevent* i_ with High heat followed by Medium
Reduce Static* i heat for enhanced fabric care
Steam Boost* and energy savings.
Energy Saver
Damp Dry Signal !_
Wrinkle Prevent* i
Reduce Static* i
Steam Boost*
Energy Saver
Damp Dry Signal
Wrinkle Prevent t
Reduce Static*
Energy Saver
Damp Dry Signal
Wrinkle Prevent*
Reduce Static*
Energy Saver
@
More 1:10 Wrinkle Prevent* !
or
70
More 55 Damp Dry Signal [!_
Normal Wrinkle Prevent* [
Less Steam Boost* i
Energy Saver
Uses Medium heat to dry large
loads of mixed fabrics and items.
Normal is the preferred energy
cycle.
Uses a stepped drying temperature
from Medium to Low for improved
moisture removal and enhanced
fabric care.
Uses Extra Low heat to gently
dry delicate items.
This is a long cycle with high heat,
which has been proven to reduce
household bacteria. This cycle is
not recommended for all fabrics.
Use for large loads of heavyweight
fabrics.
Use for drying large, bulky items;
do not overfill dryer drum. Partway
through the cycle, the signal will
sound for 2 minutes to indicate
when it is time to rearrange items
for optimal drying.
* On steam models, you may select the "With Steam" setting to add a short steam cycle after 60 minutes. This is available only with High and Medium Drying
Temperature settings.
* On steam models only.
Load Size Recommendations
For best results, follow the wet load size recommendations noted
for each cycle.
_ mall load: Fill the dryer drum with 3-4 items, not more than
1/4 full.
_ Medium load: Fill the dryer drum up to about 1/2 full.
Large load: Fill the dryer drum up to about 3/4 full.
Do not tightly pack. Items need to tumble freely.
8
CYCLEGUIDE- TIMEDCYCLES
Settings and options shown in bold are default settings for that cycle.
if settings are changed, the new settings will be remembered (except on Rapid Dry). if there is a power failure, settings will return to the
default.
Not all features and cycles are available on all models.
Not all settings and options are available on each cycle.
Adjusting drying time on Timed Cycles
When you select a Timed
Cycle, the time appears in
the display. Use + and - to
increase or decrease the time
in 1-minute increments. Touch
and hold to change the time
in 5-minute increments.
The maximum dry time is 100 minutes.
Selecting the Drying Temperature
A High heat setting may be used for drying heavyweight items such
as towels and work clothes.
A Low to Medium heat setting may be used for drying
medium-weight items such as sheets, blouses, dresses,
underwear, permanent press fabrics, and some knits.
Use a no heat (air only) setting for foam, rubber, plastic,
or heat-sensitive fabrics.
Line dry bonded or laminated fabrics.
NOTE: if you have questions about drying temperatures for various
loads, refer to the care label directions.
= Drying
items to dry:
Any load
NOTE: Select Air
Only to dry foam,
rubber, plastic, or
heat-sensitive
fabrics.
Small loads and
sportswear
Small loads and
sportswear
Cycle:
Timed Dry
Rapid Dry
Air Dry
Temperature:
High
Medium
Low
Extra Low
Air Only
High
Medium
Low
Extra Low
Air Only
Default
Time:
40
26
50
Available
Options:
Wrinkle Prevent t
Wrinkle Prevent t
Wrinkle Prevent t
ii_ /i_ii_ i_ i_ i_ i _ i_i/ _i_ii i _iii i_ ii _iiii!_!_!_/iii_ i_ i_
Cycle Details:
i_ se to dry items to a damp level for items that donot require an entire drying cycle. Select a drying
temperature based on the type of fabrics in your
load. If you are unsure of the temperature to select
for a load, select the lower setting rather than the
higher setting.
Q For small loads of 3-4 items.
For small loads of 3-4 items.
On steam models, you may select the "With Steam" setting to add a short steam cycle after 60 minutes. This is available only with High and Medium Drying
Temperature settings.
CYCLEGUIDE- STEAMCYCLE(onsomemodels)
Settings and options shown in bold are default settings for that cycle.
Not all settings and options are available on each cycle.
Steam cycles are designed for use with dry loads to loosen wrinkles, reduce odors, and refresh fabrics.
Default _ble 1
Shirts,b,ouses, I I Static ! dryert°°'°ng'D°n°tadddryersheets' and slacks I Refresh I Medium I 22 ' wrinkle preven[* I _'_ Use reduce 'ight wrinkles fr°m '°ads left in the I
On steam models, you may select the "With Steam" setting to add a short steam cycle after 60 minutes. This is available only with High and Medium Drying
Temperature settings.
* On steam models only.
Load Size Recommendations
For best results, follow the load size recommendations noted
for each cycle.
Q mall load: Fill the dryer drum with 3-4 items, not more than
1/4 full.
_ Medium load: Fill the dryer drum up to about 1/2 full.
Large load: Fill the dryer drum up to about 3/4 full.
Do not overload, items need to tumble freely.
USINGYOURDRYER
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Do not dry anything that has ever had anything
flammable on it (even after washing).
Failure to follow these instructions can result in death,
explosion, or fire.
WARNING: To reduce the risk of fire, electric shock, or injury to
persons, read the IMPORTANT SAFETY INSTRUCTIONS before
operating this appliance.
1, Clean the lint screen
Clean the lint screen before each load. Pull the lint screen straight
up. Roll lint off the screen with your fingers. Do not rinse or wash
screen to remove lint. Wet lint is hard to remove. Push the lint
screen firmly back into place.
For additional cleaning information, see "Dryer Care_'
2, Load the dryer
Appearance may vary.
Open the door by pulling on the handle. Place laundry in the dryer.
Add a dryer sheet to wet load, if desired. Close the door.
iMPORTANT: Do not tightly pack the dryer, items need to tumble
freely. Tightly packing can lead to poor drying performance and may
increase wrinkling and tangling.
10
Fire Hazard
No washer can completely remove oil.
Do not dry anything that has ever had any type of oil on
it (including cooking oils).
items containing foam, rubber, or plastic must be dried
on a clothesline or by using an Air Cycle.
Failure to follow these instructions can result in death
or fire.
3,Touch POWER/CANCEL
power / cancel
Touch POWER/CANCEL to turn on the dryer.
4, Select the desired cycle
normal
n m
heavy duty wrinkle
control
bedding _elicates
=
sanitize timed
dry
refresh rapid
dry
Appearance may vary.
-- i
Select the desired cycle for your load. See the "Cycle Guide"
for more information about each cycle. Not all cycles are on all
models.
5, Adjust cycle settings, if desired
Appearance may vary.
You may adjust different settings, depending on whether you have
selected a Sensor Cycle, Timed Cycle, or Steam Cycle (on some
models). See the "Cycle Guide" for detailed information.
NOTE: Not all options and settings are available with all cycles.
Not all cycles are on all models.
Sensor Cycles:
You can select a different dryness level, depending on your load.
Touch DRYNESS LEVEL to scroll to More, Normal, or Less.
Selecting More, Normal, or Less automatically adjusts the dryness
level at which the dryer will shut off. Once a dryness level is set, it
cannot be changed without stopping the cycle.
Sensor cycles give the best drying in the shortest time. Drying time
varies based on fabric type, load size, and dryness setting. Drying
time is estimated and may change throughout the cycle. Drying
time can not be changed on Sensor Cycles.
NOTE: Sensor Cycles use a preset temperature that is not
adjustable.
Timed Cycles:
When you select a Timed
Cycle, the time appears in
the display. Touch + and - to
increase or decrease the time
in 1-minute increments. Touch and hold to change the time in
5-minute increments.
The temperature may be changed by touching Temperature until
the desired dry temperature is lit. Once a cycle has started, the
temperature can be changed after first pausing the cycle.
Steam Cycles (on some models):
Select Refresh to reduce odors and light wrinkles in dry loads.
Do not add dryer sheets. Cycle time is estimated and may change
throughout the cycle. Cycle time can not be changed on Steam
Cycles.
6, Select any additional options
Appearance may vary.
The display will show the settings for the selected cycle. To adjust
a setting, touch its name - Reduce Static, Steam Boost, or Damp
Dry Signal.
NOTE: Not all options and settings are available with all cycles.
X
7, Touch and hold START/PAUSE
to begin cycle
hold to start
Touch and hold START/PAUSE to begin the cycle,
8, Remove garments promptly
after cycle is finished
Appearance may vary.
Promptly remove garments after cycle has completed to reduce
wrinkling.
f
Changing the Sensor Cycle settings
to increase drying time
If all your loads on all Sensor Cycles are consistently not as
dry as you would like, you may change the default settings to
increase the default dryness level.
Your sensor drying settings can be adjusted to adapt to
different installations, environmental conditions, or personal
preference. This change is retained and will affect all of your
Sensor cycles, not just the current cycle/load. There are
5 drying settings, which are displayed using the time display:
01 Factory preset dryness level.
02 Slightly drier clothes, 150/o more drying time.
03 Much drier clothes, 300/o more drying time.
04 Slightly wetter clothes, 150/o less drying time.
05 Much wetter clothes, 300/o less drying time.
To change the drying settings:
NOTE: The settings cannot be changed while the dryer
is running or paused, The dryer must be in standby mode
(power is off) to adjust the default settings,
1. Before starting a cycle, touch and hold DRYNESS LEVEL
for 6 seconds,
2. Touch DRYNESS LEVEL to select the dryness level shown
in the time display: 01, 02, 03, 04 or 05.
3. Touch START/PAUSE to save the new dryness level
setting.
11
CYCLESTATUSiNDiCATORS ADDiTiONAL FEATURES
sensing
checkvent
m good aifftow
steaming
m done
check
lint screen
Appearance may vary
The Cycle Status indicators show the progress of a cycle. Not aU
indicators are available on aU models.
Sensing
The Sensing indicator wiU light during Sensor Cycles to
indicate that the moisture sensor on the dryer is operating. This
indicator will not light during Timed Cycles or options such as
Wrinkle Prevent.
Check Vent
This indicator will show the status of airflow through the dryer
and the dryer vent system for the dryer's life. During the sensing
phase at the beginning of the cycle, the Check Vent light will
come on if a blocked vent or low airflow issue is detected. This
light will stay on for the entire cycle. The light wiU be cleared
when selecting a new cycle, touching POWER, or opening the
door after the cycle has completed. This feature is available
during Sensor and Steam cycles only. For more information
on maintaining good airflow, see "Check Your Vent System for
Good Airflow".
NOTE: if there are other error issues during a cycle, the Check
Vent indicator will not light up. See "Troubleshooting" section.
Good Airflow
This indicator wiU light if there is no major vent blockage.
Steaming
This indicator wiU light when a steam function is active.
NOTE: Steam is not available on aU cycles.
Done
This will indicate that the selected cycle has ended and the load
may be removed from the dryer, if Wrinkle Prevent has been
selected, the dryer may continue to tumble the load, even if
the Done indicator is lit.
Check Lint Screen
The Check Lint Screen indicator will light when the drying
cycle is complete as a reminder to clean the lint screen.
USING THE DRYING RACK
To purchase a drying rack for your dryer, order by calling
1-877-g44-7566, You wiU need your model and serial number
and the purchase date, Remove and discard any packing
material before use,
Use the Drying Rack for items that you do not want to tumble
dry, such as sweaters and tennis shoes. When you use the
drying rack, the drum continues to turn, but the rack remains
stationary.
The drying rack is intended for use with the Timed Dry cycle
only, The drying rack cannot be used with Sensor cycles,
To use the drying rack:
iMPORTANT: Do not remove the lint screen,
1. Open dryer door,
2. Align the two hooks on the front of the drying rack with the
holes in the dryer door opening and press down fully into
holes, Rest the rear support on the dryer back ledge,
_,'I
3. Place wet items on top of the drying rack. Allow space
around items for air to circulate, The drying rack does not
move, but the drum wiU rotate; be sure to leave adequate
clearance between items and the inside of the dryer drum,
Make sure items do not hang over the edges or between
drying rack grille,
4. Close the door,
5. Select a Timed Dry/Air Only/Air Dry, or Low Temperature
cycle, items containing foam, rubber, or plastic must be
dried on a clothesline or by using the Air Only setting
or Air Dry cycle, depending on model,
6. When the cycle is selected, the Estimated Time Remaining
display shows the default time, You can change the actual
time in the cycle by increasing or decreasing the cycle time,
7. Start the dryer,
NOTE: Check the lint screen and remove any lint accumulated
from items dried on the drying rack after the cycle is finished,
12
DRYERCARE
'- LEANING THE DRYER LOCATION
l Keepdryerareaclearandfreefromitemsthatwouldblockthe [
air flow for proper dryer operation, This includes clearing piles
1
of laundry in front of the dryer.
Explosion Hazard
Keep flammable materials and vapors, such as
gasoline, away from dryer.
Place dryer at least 18 inches (460 ram) above the floor
for a garage installation.
Failure to do so can result in death, explosion, or fire.
CLEANING THE DRYER iNTERiOR
To
1.
clean dryer drum
Use a mild hand dish detergent mixed at a low
concentration with very warm water, and rub with
a soft cloth,
2. Rinse well with a wet sponge or towel,
3. Tumble a load of clean clothes or towels to dry drum
OR
Use a microfiber cloth and hot water in a spray bottle
to clean the drum and a second microfiber towel to dry.
NOTE: Garments that contain unstable dyes, such as denim
blue jeans or brightly colored cotton items, may discolor the
rear of the dryer interior. These stains are not harmful to your
dryer and will not stain future loads of clothes, Dry unstable
dye items inside out to avoid transfer of dye,
REMOVING ACCUMULATED LiNT
From inside the Dryer Cabinet
Lint should be removed every 2 years, or more often,
depending on dryer usage, Cleaning should be done by a
qualified appliance servicer,
From the Exhaust Vent
Lint should be removed every 2 years, or more often,
depending on dryer usage,
CLEANING THE LiNT SCREEN
Every load cleaning
The lint screen is located in the door opening of the dryer,
The control panel has an indicator light to remind you to clean
the lint screen after each load, A screen blocked by lint can
increase drying time,
To clean:
1. Pull the lint screen straight up, Roll lint off the screen with
your fingers, Do not rinse or wash screen to remove lint.
Wet lint is hard to remove,
2. Push the lint screen firmly back into place,
IMPORTANT:
m Do not run the dryer with the lint screen loose, damaged,
blocked, or missing, Doing so can cause overheating and
damage to both the dryer and fabrics,
m if lint falls off the screen into the dryer during removal,
check the exhaust hood and remove the lint. See "Venting
Requirements" in the installation instructions,
As needed cleaning
Laundry detergent and fabric softener residue can build up
on the lint screen, This buildup can cause longer drying times
for your clothes, or cause the dryer to stop before your load is
completely dry. The screen is probably clogged if lint falls off
while the screen is in the dryer,
Clean the lint screen with a nylon brush every 6 months,
or more frequently, if it becomes clogged due to a residue
buildup,
To wash:
1. Roll lint off the screen with your fingers,
2. Wet both sides of lint screen with hot water,
3. Wet a nylon brush with hot water and liquid detergent.
Scrub lint screen with the brush to remove residue buildup,
4. Rinse screen with hot water,
5. Thoroughly dry lint screen with a clean towel,
Reinstall screen in dryer,
13
DRYERCARE
NON=USE, STORAGE, AND MOVING CARE
Install and store your dryer where it will not freeze. Because
some water may stay in the hose, freezing can damage your
dryer. If storing or moving your dryer during freezing weather,
winterize it.
Non-Use or Storage Care
Operate your dryer only when you are at home, If you will be
on vacation or not using your dryer for an extended period of
time, you should:
1. Unplug dryer or disconnect power,
2. Clean lint screen, See "Cleaning the Lint Screen"
3. Turn off the water supply to the dryer, This helps to avoid
unintended flooding (due to a water pressure surge) while
you are away,
Moving Care
For power supply cord-connected dryers:
1. Unplug the power supply cord,
2. Gas models only: Close shut-off valve in gas supply line,
3. Gas models only: Disconnect gas supply line pipe and
remove fittings attached to dryer pipe,
4. Gas models only: Cap the open gas supply line,
5. Steam models only: Shut off water faucet.
6. Disconnect the water inlet hose from faucet, then drain the
hose, Transport hose separately,
7. Make sure leveling legs are secure in dryer base,
8. Use tape to secure dryer door,
SPECIAL iNSTRUCTiONS
FOR STEAM MODELS
Water Inlet Hose
Replace inlet hose and hose screen after 5 years of use to
reduce the risk of hose failure, Periodically inspect and replace
inlet hose if bulges, kinks, cuts, wear, or leaks are found,
When replacing your inlet hose, record the date of
replacement.
To Winterize the Dryer
1. Unplug dryer or disconnect power,
2. Shut off water faucet.
3. Disconnect water inlet hose from faucet and drain,
To Use the Dryer Again
1. Flush water pipes, Reconnect water inlet hose to faucet.
Turn on water faucet.
2. Plug in dryer or reconnect power as described in the
installation instructions,
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating,
Failure to do so can result in death or electrical shock,
For direct-wired dryers:
1. Disconnect power,
2. Disconnect wiring,
3. Steam models only: Shut off water faucet.
4. Steam models only: Disconnect the water inlet hose from
faucet; then drain the hose, Transport hose separately.
5. Make sure leveling legs are secure in dryer base,
6. Use tape to secure dryer door,
Reinstalling the Dryer
Follow the Installation instructions to locate, level, and connect
the dryer,
14
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.maytag.com/product_help -
In Canada www.maytag.ca for assistance and to possibly avoid a service call.
Dryer wiil not run Door not closed completely. Make sure the dryer door is closed completely.
START/PAUSE not touched firmly or Touch and hold START/PAUSE 2-5 seconds.
held long enough.
Household fuse is blown or circuit There may be 2 household fuses or circuit breakers for the dryer.
breaker has tripped. Check that both fuses are intact and tight, or that both circuit
breakers have not tripped. Replace the fuses or reset the circuit
breaker. If the problem continues, call an electrician.
Incorrect power supply. Electric dryers require 240ovoit power supply. Check with a
qualified electrician.
Wrong type of fuse. Use a t[meodeiay fuse.
Dryer wiil not heat Household fuse is blown or circuit The drum may be turning, but you may not have heat, Electric
breaker has tripped, dryers use 2 household fuses or circuit breakers. Replace the
fuses or reset the circuit breaker. If the problem continues, cail
an electrician.
Incorrect power supply. Electric dryers require 240ovoit power supply. Check with a
qualified electrician.
Supply line valve not open.
For gas dryers, make sure that the valve on the gas supply line
is open.
Humming or whining noise
with Steam cycle selected
(on some models)
Water pump or water inlet valve
(depending on model) on dryer
is running.
Clicking noise
Loud humming or
increased noise during
cycle
The water pump or water inlet valve on the dryer is used during the
Steam function. If the dryer has just been installed or unused for an
extended period, the pump or valve may be louder and run longer.
This is normal.
NOTE: The valve may make this noise even with no water line connected.
Thumping noise Dryer hasn't been used in a while. This is due to temporary fiat spots on the drum rollers.
The thumping sound will diminish after a few minutes.
Rattling or vibrating A small object caught between the Check the front and rear edges of the drum for small objects. Clean
noise edges of dryer drum. out pockets before laundering.
Dryer isn't properly leveled. The dryer may vibrate if not properly installed. See the Installation
Instructions. All four dryer feet should be in firm contact with the
floor.
Clothing is bailed up in dryer. When bailed up, the load w[[[ bounce, causing the dryer to vibrate.
Separate the load items and restart the dryer.
Gas valve operating. On gas dryers, you may hear the gas valve clicking as it opens and
closes. This is normal.
Load is packed tightly or exhaust vent
is blocked.
Clothes are not drying
Reduce load size to recommended load size in "Cycle Guide:'
Run the dryer for 5-10 minutes. Hold your hand under the
outside exhaust hood to check air movement. If you do not feel air
movement or air movement is minimal, clean exhaust system of lint
or replace exhaust vent with heavy metal or flexible metal vent.
See the Installation Instructions.
Energy Saver option is on. For optimal drying times, turn off Energy Saver. For optimal energy,
turn on Energy Saver.
times are too long
Clean lint screen before each load.
Lint screen is clogged with lint.
The exhaust vent or outside exhaust
hood is clogged with lint, restricting
air movement.
Run the dryer for 5-10 minutes. Hold your hand under the
outside exhaust hood to check air movement. If you do not feel air
movement or air movement is minimal, clean exhaust system of lint
or replace exhaust vent with heavy metal or flexible metal vent.
See the Installation Instructions.
J
15
TROUBLESHOOTING
f
ff you experience
Clothes are not drying
satidactorily or drying
times are too long (cont.)
First try the solutions suggested here or visit our website at www.maytag.com/product help - -_
Jn Canada www.maytag.ca for assistance and to possibly avoid a service call.
The exhaust vent is not the correct
length.
Check that the exhaust vent is not too long or has too many
turns. Long venting will increase drying times. See the installation
instructions.
The exhaust vent diameter is not the Use 4" (102 mm) diameter vent material.
correct size.
The dryer is not level. Clothes not contacting the moisture sensors during Sensor cycles.
See "Level Dryer" in the installation instructions.
The Air Only temperature setting or Select the correct temperature for the types of garments being
Air Dry cycle (depending on model) dried. See "Cycle Guide:'
has been selected.
The load is too large and heavy Separate the load to tumble freely.
to dry quickly.
Fabric softener sheets are blocking The air outlet grille is just inside the door, behind the lint screen.
the grille. Check that it is not blocked by a fabric softener sheet.
Use only one fabric softener sheet, and use it only once.
The dryer is located in a room with Proper operation of dryer cycles requires temperatures above
temperature below 45°F (7°C). 45°F (7°C).
The dryer is located in a closet. Closet doors must have ventilation openings at the top
and bottom of the door. The front of the dryer requires a minimum
of 1" (25 mm) of airspace, and, for most installations, the rear of
the dryer requires 5" (127 mm). See the Installation Instructions.
Cycle time is too short The load may not be contacting Level the dryer. See the Installation Instructions. All four dryer feet
the sensor strips on Sensor Cycles. should be in firm contact with the floor.
Steam models onJy: Clothes are Under certain environmental or installation conditions, you may
coming out of the Refresh cycle experience underdrying. Select the Timed Dry cycle, medium
with damp or wet spots, drying temperature, for 5 to 10 minutes.
The Sensor Cycle is ending early. Change the dryness level setting on Sensor Cycles. Increasing
or decreasing the dryness level will change the amount of drying
time in a cycle. If loads are consistently ending too early, see also
"Changing the Sensor Cycle settings to increase drying time:'
Lint on load Lint screen is clogged with lint. Clean lint screen before each load.
Stains on load Improper use of fabric softener. Add dryer fabric softener sheets at the beginning of the cycle.
Fabric softener sheets added to a partially dried load can
stain your garments. Do not use fabric softener sheets with
steam cycles.
Stains on drum Loose dyes in clothes. Drum stains are caused by dyes in clothing (usually blue jeans).
These will not transfer to other clothing.
Loads are wrinkled
The load was not removed from
dryer at the end of the cycle.
Steam modeJs onJy: Select Refresh Cycle to tumble the load with
water and heat. This cycle is best for reducing wrinkles from loads
left in the dryer too long.
NOTE: Refer to garment care label instructions. Dry dean-only
garments are not recommended.
The dryer was tightly packed. Dry smaller loads that can tumble freely.
Steam models only: For steam Make sure water is connected to the dryer. Check that water
cycles, the water is not properly inlet hose is connected to both the faucet and dryer's water inlet
connected with the dryer, valve. Check that the water supply is turned on.
16
TROUBLESHOOTING
First try the solutions suggested here or visit our website at www.maytag.com/product_heip -
in Canada www.maytag.ca for assistance and to possibly avoid a service call.
Odors
Recent painting, staining, or Ventilate the area. When the odors or fumes are gone from the
varnishing in the area where area, rewash and dry the clothing.
your dryer is located.
Steam models only: For steam Make sure water is connected to the dryer. Check that water inlet
cycles, the water is not properly hose is connected to both the faucet and dryer's water inlet vane.
connected with the dryer. Check that the water supply is turned on.
Odors are left in garments after
wearing.
Steam models only: To remove odors left in garments after
wearing, select Refresh. The Refresh cycle is best for reducing
wrinkles from loads left in the dryer too long.
Load too hot Allow the dryer to complete the cooldown portion of the cycle
before removing the load.
"PF" (power failure)
"L" or "L2" Diagnostic Code
(low or no line voltage
condition)
Check Vent indicator is lit.
"F# E#" (F1 El, F3 El, etc.)
variable service codes
"Loc" or "Lc"
Load removed before cooidown
portion of cycle complete.
Using Timed Dry cycle with a high
temperature setting.
Select a Sensor cycle with a lower heat setting to avoid overdrying
the load.
The drying cycle has been
interrupted by a power failure.
There may be a problem with your
home power supply, keeping the
dryer's heater from turning on.
The lint screen or vent is clogged;
the vent is crushed or kinked or
has too many turns.
The dryer is in need of service.
The Control Lock is enabled.
Touch and hold START/PAUSE to restart the dryer. NOTE: The
Control Lock function may be enabled when recovering from a
power failure. To unlock the control, touch and hold CONTROL
LOCK for at least 3 seconds.
The dryer will continue to run when this diagnostic code is present.
Touch any setting or option name to dear the code from the
display and return to the estimated time remaining.
Try the following:
Check to see if a household fuse has blown or circuit breaker
has tripped. Electric dryers use two household fuses or breakers.
Replace the fuse or reset the circuit breaker.
Confirm that the power cord is properly installed. Refer to
the Installation Instructions for details.
Select a Timed Dry heated cycle, and restart the dryer.
if the message persists, consult a qualified electrician.
The dryer will continue to run when this diagnostic code is present.
Touch any setting or option name to dear the code from the
display and return to the estimated time remaining.
Try the following:
Clean lint screen.
Check to see if the vent run from the dryer to the wail is
crushed or kinked.
. Confirm that the vent run from the dryer to the wail is free
of lint and debris.
. Confirm that the exterior vent exhaust hood is free of lint
and debris.
. Confirm that your vent system fails within the recommended
run length and number of elbows for the type of vent you are
using. Refer to "Plan Vent System" in the Installaton Instructions
for details.
. Select a Timed Dry heated cycle, and restart the dryer.
if the message persists, have your entire home venting run
cleaned.
if a code beginning with an "F" appears in the display,
alternating between F# and E#, the dryer control has
detected a problem that requires service. Call for service.
Touch and hold CONTROL LOCK for 3 seconds to unlock
the controls of the dryer. During this time the LED Display
will count down 32ol. When the Control Lock is disabbd,
the LED Display will clear.
J
17
MAYTAG ®LAUNDRY
LiMiTED WARRANTY
ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS
REQUIRED TO OBTAIN WARRANTY SERVICE.
Please have the following information available when you call the
Customer eXperience Center:
[] Name, address, and telephone number
[] Model number and serial number
[] A clear, detailed description of the problem
[] Proof of purchase including dealer or retailer name and address
iF YOU NEED SERVICE:
r=l
1. Before contacting us to arrange service, please determine whether your product requires repair. Some i_1 i_1
questions can be addressed without service. Please take a few minutes to review the Troubleshooting
or Problem Solver section of the Use and Care Guide, scan the QR code on the right to access
additional resources, or visit https://www.maytag.com/product_help.
2. All warranty service is provided exclusively by our authorized Maytag Service Providers.
In the U.S. and Canada, direct all requests for warranty service to:
Maytag Customer experience Center
in the U,S,A. call 1=800=688=gg00, in Canada call 1=800=807=6777,
If outside the 50 United States and Canada, contact your authorized Maytag dealer to determine ifanother warranty applies.
https://www.rnaytag.corn/product_help
FIRST YEAR LIMITED WARRANTY (PARTS AND LABOR)
For one year from the date of purchase, when this major appliance
is installed, operated, and maintained according to instructions
attached to or furnished with the product, Maytag brand of
Whirlpool Corporation or Whirlpool Canada LP (hereafter
"Maytag") will pay for factory specified parts and repair labor to
correct defects in materials or workmanship that existed when this
major appliance was purchased.
SECOND THROUGH TENTH YEAR LIMITED WARRANTY
(DRUM MOTOR AND STAINLESS STEEL BASKET ONLY =
LABOR NOT INCLUDED)
In the second through tenth years from the date of original
purchase, when this major appliance is installed, operated, and
maintained according to instructions attached to or furnished
with the product, Maytag will pay for factory specified parts for
the following components to correct non-cosmetic defects in
materials or workmanship in these parts that prevent function of
this major appliance and that existed when this major appliance
was purchased. This is a limited 10 year warranty on the below
named parts only and does not include repair labor.
[] Drum (Side Walls Only)
[] Drive Motor
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS
LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS
PROVIDED HEREIN. Service must be provided by a Maytag
designated service company. This limited warranty is valid only
in the United States or Canada and applies only when the major
appliance is used in the country in which it was purchased. This
limited warranty is effective from the date of original consumer
purchase. Proof of original purchase date is required to obtain
service under this limited warranty.
1. Commercial, non-residential, multiple-family use, or use inconsistent
with published user, operator, or installation instructions.
2. In-home instruction on how to use your product.
3. Service to correct improper product maintenance or installation,
installation not in accordance with electrical or plumbing codes, or
correction of household electrical or plumbing (i.e. house wiring,
fuses, or water inlet hoses).
4. Consumable parts (i.e. light bulbs, batteries, air or water filters, etc.).
S. Conversion of your product from natural gas or LR gas or reversal
of appliance doors.
6. Damage from accident, misuse, abuse, fire, floods, acts of God, or
use with products not approved by Maytag.
7. Repairs to parts or systems to correct product damage or defects
caused by unauthorized service, alteration, or modification of the
appliance.
8. Cosmetic damage including scratches, dents, chips, and other
damage to appliance finishes unless such damage results from
defects in materials and workmanship and is reported to Maytag
within 30 days.
g. Discoloration, rust, or oxidation of surfaces resulting from caustic
or corrosive environments, including but not limited to, high salt
concentrations, high moisture or humidity, or exposure to chemicals.
10. Pick-up or delivery. This product is intended for in-home repair.
11. Travel or transportation expenses for service in remote locations
where an authorized Maytag servicer is not available.
12. Removal or reinstallation of inaccessible appliances or built-in
fixtures (i.e. trim, decorative panels, flooring, cabinetry, islands,
countertops, drywall, etc.) that interfere with servicing, removal, or
replacement of the product.
13. Service or parts for appliances with original model/serial numbers
removed, altered, or not easily determined.
The cost of repair or replacement under these excluded
circumstances shall be borne by the customer,
DISCLAIMER OF iMPLiED WARRANTIES
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR
A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces
do not allow limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty
gives you specific legal rights, and you also may have other rights that vary from state to state or province to province.
DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY
Maytag makes no representations about the quality, durability, or need for service or repair of this major appliance other than the
representations contained in this Warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes
with this major appliance, you should ask Maytag or your retailer about buying an extended warranty.
LIMiTATiON OF REMEDIES; EXCLUSION OF iNCIDENTAL AND CONSEQUENTIAL DAMAGES
YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN.
MAYTAG SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the
exclusion or limitation of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives
you specific legal rights, and you also may have other rights that vary from state to state or province to province.
01/14
18
SECURITI DE LA SE.CHEUSE
Votre s_curit_ et celle des autres est tr_s importante.
Nous donnons de nombreux messages de s6curit6 importants darts ce manuel et sur votre appareil m6nager. Assurez-vous de
toujours lire tous les messages de s6curit6 et de vous y conformer.
Voici le symbole d'alerte de securit6.
Ce symbole d'alerte de s_curit6 vous signale les dangers potentiels de d6c_s et de blessures graves & vous
et & d'autres.
Tousles messages de s6curit6 suivront le symbole d'alerte de s6curit6 et le mot "DANGER" ou
"AVERTISSEMENT'. Ces mots signifient :
Risque possible de d_c_s ou de biessure grave si vous ne
suivez pas irnm_diaternent les instructions.
Risque possibJe de d_c_s ou de bJessure grave si vous
ne suivez pas les instructions.
Tousles messages de s6curit6 vous diront quel est le danger potentiel et vous disent comment r6duire le risque de blessure et
ce qui peut se produire en cas de non-respect des instructions.
AVER r |SSEMENT - d,i.oo°di ,,
m
m
m
L'instaJJation de la s_cheuse _ Jinge doit 6tre effectu_e par un instalJateur qualifi_.
installer la s6cheuse conforrn6rnent aux instructions du fabricant et aux codes Iocaux.
Ne pas instalJer de s_cheuse & tinge avec des rnat_riaux d'_vacuation en piastique
souple ou un conduit rn6talJique souple (de type papier d'alurniniurn). Si un conduit
rn6tallique souple est installS, ceJui-ci doit 6tre d'un type sp_cifique identifi_ par Je
fabricant de I'appareil et convenir & une utilisation avec les s_cheuses & tinge. Les
rnat_riaux d'_vacuation soupJes sont connus pour s'affaisser, 6tre facilernent _cras_s
et bloquer la charpie. Ces situations obstrueront le d_bit d'air de la s_cheuse & tinge et
augrnenteront le risque d'incendie,
Pour r_duire le risque de biessure grave ou de d_c_s, suivre routes
les instructions d'installation.
Conserver ces instructions,
19
Avertissements de la proposition 65 de I'Etat de Californie
AVERTISSEMENT " Ce produit contient au moins un produit chimique connu par I'l._tat de Californie pour _tre & I'origine de
cancers.
AVERTISSEMENT ' Ce produit contient au moins un produit chimique connu par I'Etat de Californie pour 6tre & I'origine de
malformations et autres d6ficiences de naissance.
Dans I'Etat du Massachusetts, les instructions d'installation suivantes sont applicables :
[] Les travaux d'installation et reparation doivent 6tre ex6cutes par un plombier ou tuyauteur qualifie ou licenci6, ou par le
personnel qualifie d'une entreprise licenciee par I'l_tat du Massachusetts.
[] Si une vanne & boisseau spherique est utilisee, elle doit comporter une manette "T".
[] Si un conduit de raccordement flexible est utilis6, sa Iongueur ne doit pas d6passer 3 pi.
AVERTISSEMENT : Pour votre s6curit6, les renseignements dans ce manuel doivent
_tre observes pour r_duire au minimum les risques d'incendie ou d'e×plosion ou pour
6viter des dommages au produit, des blessures ou un d_c_s.
- Ne pas entreposer ou utiliser de I'essence ou d'autres vapeurs ou liquides
inflammables & proximit_ de cet appareil ou de tout autre appareil _lectrom_nager.
- QUE FAIRE DANS LE CAS D'LINE ODEUR DE GAZ :
® Ne pas tenter d'allumer un appareil.
Ne pas toucher & un commutateur electrique; ne pas utiliser le t_16phone se trouvant
sur les lieux.
l_vacuer tous les gens de la piece, de I'_difice ou du quarrier.
o Appeler imm_diatement le fournisseur de gaz d'un t_l_phone voisin. Suivre ses
instructions.
®,& defaut de joindre votre fournisseur de gaz, appeler les pompiers.
- L'installation et I'entretien doivent _tre effectu_s par un installateur qualifi_, une
agence de service ou le fournisseur de gaz.
AVERTISSEMENT : L'odorat ne permet pas toujours la detection d'une fuite de gaz.
Les distributeurs de gaz recommandent I'emploi d'un detecteur de gaz (homologation UL ou CSA).
Pour d'autre information, contacter le foumisseur de gaz local.
En cas de detection d'une fuite de gaz, executer les instructions "Que faire dans le cas d'une odeur de gaz".
iMPORTANT : L'installation du gaz dolt se conformer aux codes Iocaux, ou en I'absence de codes Iocaux, au code canadien
d'installation B149.1 du gaz naturel ou du propane.
La secheuse dolt Ctre electriquement reliee &la terre conformement aux codes Iocaux, ou en I'absence de codes Iocaux, au Code
canadien de 1'61ectricit6, CSA C22.1.
IMPORTANT : Pour mettre I'ancienne secheuse au rebut ou pour la remiser, enlever la porte. I
I
20
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Maytag MED5100DW0 Le manuel du propriétaire

Catégorie
Sèche-linge électriques
Taper
Le manuel du propriétaire

dans d''autres langues