CREE LIGHTING KBL-C Wireless Guide d'installation

Marque: CREE LIGHTING

Modèle: KBL-C Wireless

Taper: Guide d'installation

KBL-C Series

WIRELESS LED Luminaire

Universal Hook and Cord or Pendant Mount with Sensor

1 of 6 LPN00881X0002A0_B

INSTALLATION INSTRUCTIONS

INSTRUCTIONS D’INSTALLATION

IMPORTANT SAFEGUARDS

When using electrical equipment, basic safety precautions should always

be followed including the following:

READ AND FOLLOW ALL SAFETY

INSTRUCTIONS

1. DANGER- Risk of shock- Disconnect power before installation.

DANGER – Risque de choc – Couper l’alimentation avant

l’installation.

2. This luminaire must be installed in accordance with the NEC or your

local electrical code. If you are not familiar with these codes and

requirements, consult a qualied electrician.

Ce produit doit être installé conformément à NEC ou votre code

électrique local. Si vous n’êtes pas familier avec ces codes et ces

exigences, veuillez contacter un électricien qualié.

3. Suitable for damp location.

Convient aux emplacements humides.

4. Maximum ambient operating temperature: 9L, 12L, 18L = 50°C and

24L, 30L, and 35L= 40°C.

Température ambiante maximale de fonctionnement:

9L, 12L, 18L = 50°C et 24L, 30L, et 35L= 40°C.

5. MIN 90°C SUPPLY CONDUCTORS

LES FILS D’ALIMENTATION 90°C MIN.

6. This equipment should be installed and operated with a minimum

distance 20cm between the radiator and your body.

L’équipement doit etre installe d’une facon qu’une distance minimum

de 20cm soit maintenue entre l’emetteur et toute partie du corps.

7. Check to make sure that all input power connections have been

properly made and the module is grounded to avoid potential

electrical shock.

8. DO NOT lift luminaire by the power cord or any of the cables

connected to the LED heatsink and LED driver.

9. All electrical connections for the sensor have been made at the

factory.

10. The sensor is designed for mounting heights between 8 ft. to 40 ft.

(2.4 m to 12.2 m).

11. When mounting heights are above 30ft. (9.1 m), the sensor

generally only detects large objects such as forklift trucks.

12. When the sensor lens assembly is removed the exposed sensor

body is sensitive to electrostatic discharge. Take the necessary

steps to avoid possible damage to the sensor.

13. Use Class 1 Wiring methods ONLY

SAVE THESE INSTRUCTIONS FOR

FUTURE REFERENCE

TO INSTALL:

HOOK AND CORD MOUNT

STEP 1:

Push down on retainer spring until top of spring is free of luminaire

hook. See Figure 1.

STEP 2:

Slide hook into securely mounted customer supplied eye hanger

and return retainer spring to original position.

NOTE: The luminaire should already be factory set for correct

balance. If necessary, the fixture may be balanced by loosening the

hook adjustment screws on the top of the housing and sliding the

hook as necessary for correct balance. Tighten hook adjustment

screws when finished. See Figure 1.

STEP 3:

Make wiring connections per the Electrical Connections section.

After electrical connections for luminaires with a sensor go to

pages 4-6 for installation of sensor.

NOTES:

• For each mounting application below, when mounting to surface

ensure that the mounting surface and customer supplied hardware is

capable of supporting the weight of the luminaire.

• The center of mounting is NOT the same as the center of luminaire.

• Images used in this installation sheet are for illustration purpose,

there are dierent congurations of the luminaire.

Luminaire Hook

Hook Adjustment Screws

Retainer Spring

1/2” (13mm) IP, 0.875”

(22mm) O.D. Knockout

KBL WIRELESS WITH

UL NETWORK SENSOR

KBL WIRELESS

WITH UH NETWORK

SENSOR

KBL

WIRELESS

2 of 6 LPN00881X0002A0_B

PENDANT MOUNT

STEP 1:

Remove hinged splice box from top of housing

by loosening screw and sliding box to the right

and up from “L” channel. Unhook from hinge

holes. See Figure 2.

STEP 2:

Remove hook, slider plate and cord and

discard. Plug junction box knockout hole with

provided junction box plug.

STEP 3:

Attach the supplied pendant mount slider plate

using (2) supplied screws. Use 3/4” threaded

pendant, along with two customer supplied

locknuts (one for inside the hinged splice box

and one for outside the splice box). Pull supply

leads into position from customer supplied

conduit.

Note: If necessary, the luminaire may be

balanced by loosening (2) screws for pendant

adjustment on the top of the hinged splice box

and sliding the adjustment plate as necessary

for correct balance. Tighten (2) screws when

finished. See Figure 2.

STEP 4:

Attach one end of the hinged splice box to

luminaire by aligning hinge slots on Mounting

Bracket with hinges (on splice box), and then

inserting the hinges into the slots.

STEP 5:

Make wire connections per Electrical

Connections and then push the leads into

hinged splice box. Close the hinged J-box and

re-tighten the screw. See Figure 3.

STEP 6:

Secure other end of the hinged splice box

to luminaire by sliding screw on Mounting

Bracket up and over in “L” channel on the

hinged splice box. See Figure 2.

STEP 7:

Secure luminaire to hinged splice box by

tightening screw. For luminaires with a sensor

go to pages 4-6 for installation of sensor.

REFLECTOR INSTALLATION

TOOL LESS REFLECTOR:

STEP 1:

Place the reflector tabs between the luminaire

mounting tabs. See Figure 4.

Step 2:

Turn the reflector clockwise until it locks into

place under the locking tab. See Figure 4.

NOTE: For additional reflector security

#6 x 5/16” self tapping screws can be added

to the screw holes in the mounting tabs. See

Figure 4.

Step 3:

To remove the reflector, lift the locking tab and

turn the reflector counter-clockwise.

“L” Channel

Pendant Mount Hole

3/4” (19mm) IP, 1.125”

(29mm) O.D.

1/2” (13mm) IP,

0.875” (22mm)

O.D. Knockouts

3/4” (19mm) IP,

1.125” (29mm)

O.D. Knockouts

Adjustment Screws

Hinged Splice

Box

Pendant Slider

Plate

Hinged J-box

Screw

Luminaire Mounting

Tabs

Luminaire Mounting

Tabs

Screw

Holes

Locking

Tab

3 of 6 LPN00881X0002A0_B

Mounting Ring

Reflector

Lens with V-band

Screw

STANDARD REFLECTOR:

STEP 1:

Loosen the (4) screws, shown in Figure 5, at

least 0.1 inch from the heatsink.

NOTE: The view in Figure 5 is of the underside

of the luminaire.

Mounting Lens or Wire Guard To

Aluminum Reflector

STEP 1:

Secure the hinge retainer and frame hinge to

the reflector using supplied screw and lock

nut. See Figure 6.

NOTE: Reflector is pre-punched at position of

this installation.

STEP 2:

Swing the wire guard into place and secure to

the reflector with the attached spring latch.

See Figure 6.

Mounting Lens or Wire Guard To

Prismatic Reflector

STEP 1:

Place lens or wire guard onto the bottom of

reflector, and place V-band around lens and

reflector. See Figure 7.

STEP 2:

Secure lens or wire guard to reflector by

tightening screw on V-band. (See Figure 7) or

installing spring on V-band (See Figure 8).

SITE MAP LABEL

STEP 1:

Remove unit site map label SNAP address.

See Figure 9.

STEP 2:

Apply site map label to the correct position on

the site map. See

Figure 9.

INSTALLING SAFETY CABLE

NOTE: Safety Cable is sold separately as an

accessory, please refer to installation sheet in

safety cable packaging for complete installing

instructions.

STEP 1:

Attach one end of the safety cable through the

hole on the lower housing (either side). See

Figure 10.

STEP 2:

Attach other end of the safety cable to

mounting surfaces using customer supplied

hardware.

SYSTEM COMMISSIONING AND

CUSTOMIZING

System commissioning is required for the

fixtures to be recognized on the Simply SNAP

network. Contact Cree Lighting at 800-236-

6800 for more details about commissioning

and customizing.

Reflector Hinge Retainer

Frame Hinge

Site Map

Label

Reflector

Lens with V-band

Spring

5Loosen

Screws

Safety Cable

4 of 6 LPN00881X0002A0_B

ELECTRICAL CONNECTIONS

STEP 1:

NOTE: USE MIN. 90°C SUPPLY CONDUCTORS for 120-480V luminaires.

Make the following Electrical Connections:

a. For 120/277/347V connect the black fixture lead to the voltage

supply or Hot 1 (for 208/240/480V wiring).

b. For 120/277/347V connect the white fixture lead to the neutral

supply or Hot 2 (for 208/240/480V wiring).

c. Connect the green or green/yellow ground lead to the green wire

position of the terminal block.

STEP 2:

The Blue/White low-voltage wires are used to override the luminaire to

full output. They may be connected to third-party equipment to provide an

override signal to the luminaire. Do not connect the Blue/White wires to a

voltage supply. The wires should be capped if not being used.

• SHORT: Luminaire overrides to full output

• OPEN: Luminaire operates normally

LINE

OR HOT 1

GREEN

LINE-BLACK

GROUND-GREEN

NEUTRAL-WHITE

NEUTRAL

OR HOT 2

SUPPLY WIRING

LUMINAIRE

BLUE W/WHITE

Wire Form

SENSOR INFORMATION

For programming of sensor and more detailed description

of sensor visit https://legrand.us/lighting-controls-and-

systems/occupancy-and-vacancy-sensors/in-fixture-

sensors/line-low-voltage-0-10v-pir-fix-sens-120-277vac-

no-ir-conf/p/fsp-202.

The FSP-202 sensor has been preset with the optimal

settings to provide the widest range of user flexibility

and performance of the Synapse Environment. Sensor

characteristics can be modified in the Synapse user

interface.

NOTE: Ensure that you remove the label on the unit that

says, “Remove This Label Before Installing Lens”. If this

label is not removed, the sensor will not work properly.

INSTALLING UL (120V-277V)SENSOR

STEP 1:

Rotate the wire form up as shown. The wire form will snap

into position to hold the Sensor horizontal. See Figure 11.

STEP 2:

Locate the wire form on the sensor and install onto the

luminaire by inserting the wire form into the (2) tabs under

the driver box. See Figure 12 on the next page.

5 of 6 LPN00881X0002A0_B

Driver Box

Wire

Form

Tabs

Sensor Adjustment

Screw

INSTALLING UH (347V-480V) SENSOR

STEP 1:

Rotate the wire form up as shown. The wire form will snap into position

to hold the Sensor horizontal. Confirm that Sensor screw is tight. See

Figure 13.

STEP 2:

Locate the wire form on the sensor and install onto the luminaire

by inserting the wire form into the (2) tabs under the driver box. See

Figure 14.

STEP 3:

Rotate Sensor as needed to level position or adjust field of view.

NOTE: The horizontal position is fixed.

Driver Box

Wire

Form

Tabs

Sensor Adjustment

Screw

Wire Form

6 of 6 LPN00881X0002A0_B

www.creelighting.com

creelighting.com/warranty for warranty and specifications. Cree® and the Cree Lighting logo are registered trademarks of

SMART Global Holdings, Inc. NEMA® is a registered trademark of the National Electrical Manufacturers Association. The

Synapse® is a registered trademark of Synapse Wireless, Inc.

TECHNICAL SUPPORT

If unable to successfully resolve problems with the sensor, call 800-236-

6800 for Cree Lighting technical support.

FEDERAL COMMUNICATION COMMISSION INTERFERENCE

STATEMENT

CAUTION: Changes or modifications not expressly approved could void

your authority to use this equipment.

This device complies with Part 15 of the FCC Rules. Operation to

the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation.

The LED in the front of this device operates within Risk Group 1 levels

per IEC 62471.

This device has been tested and found to comply with the limits for

a Class A digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference when the device is operated in a commercial environment.

This device generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of

this device in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference at his

own expense.

INDUSTRY CANADA STATEMENT

This device complies with Industry Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions: (1) this

device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation

of the device. In addition, this device complies with ICES-005 of the

Industry Canada (IC) Regulations.

Le présent appareil est conforme aux CNR d’Industrie Canada

applicables aux appareils radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas

produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage est susceptible

d’en compromettre le fonctionnement.

Radiation Exposure Statement:

• This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment. This equipment should be

installed and operated with minimum distance 20 cm between the

radiator and your body.

• This transmitter must not be co-located or operating in conjunction

with any other antenna or transmitter.

• The antennas used for this transmitter must be installed to provide

a separation distance of at least 20 cm from all persons and

must not be co-located or operating in conjunction with any other

antenna or transmitter.

Torque clamp bolt

¼-1/2 Turn

Remove lens to access dials

INSTALLING REMOTE SENSOR

NOTE: Install Clamp onto beam and turn Bolt until it contacts the

beam, torque Beam Clamp Bolt an additional 1/4-1/2 of a turn after

bolt contacts the beam. Insure clamp is secure prior to adjusting

Sensor position. See Figure 15.

The remaining 2 screws can be used to fine tune the position/view

of the Sensor. See Figure 15.

SENSOR DESCRIPTION

The FSP-202 is a motion sensor that controls lighting levels based

on occupancy and ambient light.

The sensor uses passive infrared (PIR) sensing technology that

reacts to changes in infrared energy (moving body heat) within

the coverage area. Once the sensor stops detecting movement

and the time delay elapses, lights will go from high to low mode

and eventually turn off if it is desired. Sensors must directly “see”

motion of a person or moving object to detect them, so careful

consideration must be given to sensor luminaire placement and

lens selection. Avoid placing the sensor where obstructions may

block the sensor’s line of sight.

The FSP-202 is designed for indoor environments. The FSP-202 is

preset from Cree Lighting to optimize functionality and flexibility of

the sensor’s behavior through the Synapse user interface. Factory

settings from Cree Lighting are listed below. See Figure 16.

KBL Wireless FSP-202 Settings:

Mode = C

Dim = 10V

Time = 30s

CREE LIGHTING KBL-C Wireless Guide d'installation

Marque: CREE LIGHTING

Modèle: KBL-C Wireless

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: CREE LIGHTING KBL-C Wireless Installation guide

Documents connexes

CREE LIGHTING KBL-C Wireless Emergency Guide d'installation

CREE LIGHTING KBL-C Wireless Guide d'installation

CREE LIGHTING KBL-C Wireless Guide d'installation

dans d''autres langues

Documents connexes

Autres documents