Edge-Core AS7535-28XB Ethernet Switch Mode d'emploi

Taper
Mode d'emploi

Ce manuel convient également à

1
Quick Start Guide
1. PSU LED: Green (OK), Amber (fault)
2. QSFP-DD Port LEDs: Blue (400G), Cyan (200G), Green (100G),
Yellow (50G)
3. QSFP28 Port LEDs: Green (100G), Cyan (50G), Magenta (40G),
Blue (25G), Yellow (10G)
4. SFP28 Port LEDs: Blue (25G), Green (10G), Cyan (1G)
5. System LEDs:
PSU1/2 — Green (OK), Amber (fault)
DIAG — Green (OK), Orange (fault detected)
FAN — Green (OK), Orange (fault)
LOC — Blinking Blue (OK)
ALARM — Green (OK), Red (alarm)
6. RJ-45 Management Port LEDs: Left (link), Right (activity)
7. BITS/ToD LEDs: Green (valid BITS), Blinking Green (1PPS ToD)
1
6
4
7
25
3
E052022-CS-R01
150200002489A
Ethernet Switch
AS7535-28XB
1.
AS7535-28XB (includes 2 PSUs and 6 fan trays)
2. Rack Mounting Kit—2 brackets and 8 screws
3. Grounding kit—grounding lug, 2 screws, and 2 washers
4. (Optional) AC power cord
5. Documentation—Quick Start Guide (this document) and Safety
and Regulatory Information
Package Contents
Overview
FRU Replacement
1
Status LEDs
1. 2 x DC or AC PSUs
2. 2 x 100G QSFP28 ports
3. 2 x 400G QSFP-DD ports
4. 24 x 25G SFP28 ports
5. Product tag
6. Management I/O: 1000BASE-T RJ-45, RJ-45 console,
Micro-USB console, reset button
7. BITS/ToD RJ-45 timing ports
8. 10MHz/1PPS I/O
9. GNSS antenna
10. USB Type C storage port
11. RJ-45 alarm port
12. 6 x fan trays
13. Grounding screw
1
12
4 7
11
6
13
5
9
10
8
2
3
www.edge-core.com

2 3 4 5
Fan Tray Replacement
1. Loosen the fan tray screw.
2. Pull out and remove the fan
tray.
3. Install replacement fan tray.
PSU Replacement
1. Remove the power cord.
2. Press the release latch and
remove the PSU.
3. Install replacement PSU.
Quick Start Guide
2
Mount the Device in an EIA-310 Rack
1. For a 300mm-deep rack, use the four front screw holes to attach
each of the brackets to the device with four of the included bracket
screws. (For a 280mm-deep rack, use the four recessed screw
holes.)
2. Use the screws and cage/clip nuts supplied with the rack to
secure the device in the rack.
Ground the Device
Verify Rack Ground
Ensure the rack is properly grounded and in compliance with
international and local standards. Verify that there is a good electrical
connection to the grounding point on the rack (no paint or isolating
surface treatment).
Attach Grounding Wire
Attach the grounding wire (#14 AWG/1.5 mm2, green with yellow stripe)
to the grounding point on the device’s rear panel or side panel. Then
connect the other end of the wire to rack ground.
Connect Power
a. AC Power
Install one or two AC PSUs in the device, if they are not already installed
in the factory. Then connect an external AC power source to the PSUs.
b. DC Power
Install one or two DC PSUs (part number CDR-6011-6M4 only) in the
device, if they are not already installed in the factory.
Connect an external DC power source to the PSUs. Or, connect to a no-
tolerance DC mains supply with a UL/CSA-approved circuit breaker
rated at 16 A.
Warning:
For a safe and reliable installation, use only
the accessories and screws provided with the device. Use
of other accessories and screws could result in damage to
the unit. Any damages incurred by using unapproved
accessories are not covered by the warranty.
Avertissement:
Pour une installation sûre et fiable,
utilisez uniquement les accessoires et les vis fournies avec
l’appareil. L’utilisation d’autres accessoires et vis pourrait
endommager l’appareil. Les dommages causés par
l’utilisation d’accessoires non approuvés ne sont pas
couverts par la garantie.
Caution:
The device must be installed in a restricted-access
location.
Attention:
L’appareil doit être installé dans un emplacement
à accès restreint.
Note:
The device has the Open Network Install Environment
(ONIE) software installer preloaded, but no software image.
Information about compatible software can be found at
www.edge-core.com.
Note:
The drawings in this document are for illustration only
and may not match your particular model.
1
1
3
Caution:
The earth connection must not be removed unless
all supply connections have been disconnected.
Attention:
Le raccordement à la terre ne doit pas être retiré
sauf si toutes les connexions d’alimentation ont é
débranchées.
2
Rear Panel Side Panel
3
Installation
Quick Start Guide
3
1. Connect the ground wire / protective earth.
2. Connect the -44 – -60 VDC wire.
3. Connect the DC return wire.
Make Network Connections
QSFP-DD/QSFP28/SFP28 Ports
Install transceivers and then connect fiber optic cabling to the transceiver
ports. Alternatively, connect AEC/AOC/DAC cables directly to the QSFP-
DD/QSFP28/SFP28 slots.
The following transceivers are supported in the QSFP-DD ports:
400GBASE-SR8, DR4, FR4, AEC cable
The following transceivers are supported in the QSFP28 ports:
100GBASE-SR4, PSM4, LR4, ER4, ZR4, CR4, AOC
40GBASE-SR4, PSM4, LR4
The following transceivers are supported in the SFP28 ports:
25GBASE-SR, LR, BX BiDi
10GBASE-SR, LR, CR, BX BiDi, T
1000BASE-SX, LX, BX BiDi, T
Connect Timing Ports
RJ-45 BITS/ToD
Use Cat. 5e or better twisted-pair cables to connect the Building-
Integrated Timing Supply (BITS) and Time of Day (ToD) ports to other
synchronized devices.
10MHz/1pps
Use coax cables to connect the 10 MHz and 1-pulse-per-second (1PPS)
ports to other synchronized devices.
GNSS Antenna
Attach an external antenna to the GNSS antenna port for clock
synchronization with GPS time.
Make Management Connections
Mgmt RJ-45 Port
Connect Category 5, 5e or better twisted-pair cable.
RJ-45 Console Port
Use an RJ-45-to-DB-9 null-modem console cable (not included) to
connect to a PC running terminal emulator software. Use a USB-to-male
DB-9 adapter cable (not included) for connections to PCs that do not
have a DB-9 serial port.
Configure the serial connection: 115200 bps, 8 characters, no parity,
one stop bit, 8 data bits, and no flow control.
Console cable pinouts and wiring:
Caution:
Before connecting power supply cables to the
device, ensure that power to the feed lines is turned off at the
supply circuit breaker or disconnected from the power bus.
Attention:
Avant de connecter les câbles d’alimentation à
l’appareil, assurez-vous que l’alimentation des lignes
d’alimentation est coupée au niveau du disjoncteur
d’alimentation ou déconnectée du bus d’alimentation.
Caution:
Use a UL/IEC/EN 60950-1 and/or 62368-1
certified power supply to connect to a DC converter, and a #14
AWG/1.5 mm2 (for -44 VDC to -60 VDC PSU) wire to connect
to a DC PSU.
Attention:
Utilisez une alimentation certifiée UL/IEC/EN
60950-1 et/ou 62368-1 pour le connecter à un convertisseur
CC et un câble AWG #14/1.5 mm2 (pour -44 VDC à -60 VDC)
pour vous connecter à une alimentation CC.
Caution:
All DC power connections should be performed by
a qualified professional.
Attention:
Toutes les connexions d’alimentation CC doivent
être effectuées par un professionnel qualifié.
Note:
It is suggested to use the following for DC power:
One UL 1015 AWG#10-14 stranded wire, 2m maximum
(-44VDC – -60VDC: Input+)
One UL 1015 AWG#10-14 stranded wire, 2m maximum (VDC
return: Input-)
One UL 1015 AWG#10-14 stranded wire, 2m maximum,
(green/yellow) green with yellow stripe (PE)
Note:
The DC terminal screws should be tightened to a
torque of 7 in-lbs maximum.
1
3
2
4
Device’s RJ-45 Console Null Modem PC’s 9-Pin DTE Port
6 RXD (receive data) <---------------- 3 TXD (transmit data)
3 TXD (transmit data) ----------------> 2 RXD (receive data)
4,5 SGND (signal ground) ------------------ 5 SGND (signal ground)
5
6
Quick Start Guide
4
Hardware Specifications
Size (WxDxH) 438.4 x 300 x 43.3 mm (17.26 x 11.81 x 1.7 in.)
Weight 7.5 kg (16.53 lb), with two installed PSUs
Temperature Operating: -40° C to 65° C (-40° F to 149° F)
Transportation: -40° C to 85° C (-40° F to 185° F)
Storage: -40° C to 85° C (-40° F to 185° F)
Humidity Operating: 5% to 95% (non-condensing)
Power
Consumption
(at 25° C)
Maximum: 383.6 W
Typical: 164.03 W
Minimum: 95.11 W
System Input
Rating
AC Input: 100–240 VAC, 50–60 Hz, 6.0–2.4 A
DC Input: -44 – -60 VDC, 15.5–9.6 A
Regulatory Compliances
Emissions EN 55032:2015/A1:2020, Class A
EN 61000-3-2:2019/A1:2021
EN 61000-3-3:2013+A1:2019
FCC Title 47, Part 15, Subpart B, Class A
VCCI-CISPR 32:2016, Class A
Immunity EN 55035:2017/A11:2020
EN 55024:2010+A1:2015
IEC 61000-4-2/3/4/5/6/8/11
Environmental Storage:
ETSI EN 300 019-1-1 Class 1.1
Temperature: -40° C to 85° C (-40° F to 185° F)
Transportation:
ETSI EN 300 019-1-2 Class 2.3
Temperature: -40° C to 85° C (-40° F to 185° F)
Operating Conditions:
ETSI EN 300 019-1-3 Class 3.2
Temperature: -40° C to 65° C (-40° F to 149° F)
Relative Humidity: 5% to 95%
Safety UL (CSA 22.2 No 62368-1 & UL 62368-1)
CB (IEC/EN 60950-1 & IEC/EN 62368-1)
Warranty Information and Technical Support
Registering your product enables you to receive a more efficient warranty service. Be sure to register at www.edge-core.com.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Edge-Core AS7535-28XB Ethernet Switch Mode d'emploi

Taper
Mode d'emploi
Ce manuel convient également à

dans d''autres langues