Danby DAS240BAHWDB Le manuel du propriétaire

Marque: Danby

Modèle: DAS240BAHWDB

Taper: Le manuel du propriétaire

Ce manuel convient également à

MODEL • MODÈLE • MODELO

DANBY PRODUCTS LIMITED, ONTARIO, CANADA N1H 6Z9

DANBY PRODUCTS INC., FINDLAY, OHIO, USA 45840

OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE

MANUAL DEL PROPIETARIO

2017.05.08

SPLIT AIR CONDITIONER & HEAT PUMP

CLIMATISEUR & POMPE A CHALEUR DIVISÉ

AIRE ACONDICIONADO Y BOMBAS DE CALOR DIVIDIDO

DAS090BAHWDB

DAS180BAHWDB

DAS240BAHWDB

FOR ANY QUESTIONS OR CONCERNS REGARDING INSTALLATION OR SERVICING OF THIS

APPLIANCE, PLEASE CONTACT THE DEALER OR BUILDER WHO SOLD THE APPLIANCE.

_____________________________________________________________________

POUR TOUTE QUESTION OU PRÉOCCUPATION CONCERNANT L’INSTALLATION OU L’ENTRETIEN

DE CET APPAREIL, VEUILLEZ CONTACTER LE REVENDEUR OU LE CONSTRUCTEUR QUI A VENDU

L’APPAREIL.

__________________________________________________________________

PARA CUALQUIER PREGUNTA O INQUIETUD RELACIONADA CON LA INSTALACIÓN O SERVICIO DE

ESTA UNIDAD, PÓNGASE EN CONTACTO CON EL DISTRIBUIDOR O CONSTRUCTOR QUE VENDIÓ LA

UNIDAD.

SPLIT AIR CONDITIONER

Owner’s Use and Care Guide ................................... 1 - 12

• Important Safety Information

• Features

• Operation Instructions

• Care and Maintenance

• Troubleshooting

CLIMATISEUR DIVISÉ

Guide d’utilisation et d’entretien du propriétaire....... 13 - 24

• Consignes de sécurité importantes

• Caractéristiques

• Consignes d’utilisation

• Soins et entretien

• Dépannage

AIRE ACONDICIONADO DIVIDIDO

Guía de utilización y cuidado para el propietario..... 25 - 36

• Información importante sobre seguridad

• Características

• Instrucciones de funcionamiento

• Cuidado y mantenimiento

• Solución sugerida

CONTENTS

TABLE DES MATIÈRES

ÍNDICE

SAFETY REQUIREMENTS

To avoid installation or operation difﬁ culties, read

these instructions before ﬁ rst use of the product.

• Use this appliance only for its intended use, as

described in this manual.

• Never allow children to operate, play with, or

crawl inside the appliance.

• Never clean appliance parts with ﬂ ammable

ﬂ uids. The fumes can create a ﬁ re hazard or

explosion.

• Do not store or use ﬂ ammable vapors or liquids

in the vicinity of this or any other appliance. The

fumes can create a ﬁ re hazard or explosion.

• Do not use this product near water, e.g. in a wet

basement, laundry room or near a sink.

• Do not cover or block any openings on the

appliance.

• This appliance should be serviced only by a

qualiﬁ ed HVAC technician. Contact the dealer at

the location where the appliance was purchased

for information on servicing the appliance.

• Disposal of this appliance should be in

accordance with federal and local regulations.

• This appliance is not intended for use by persons

(including children) whose physical, sensory or

mental capabilities may be different or reduced,

or who lack experience or knowledge, unless

such persons receive supervision or training to

operate the appliance by a person responsible

for their safety.

• Do not climb onto or place objects on top of the

outdoor appliance.

• Do not operate this appliance with wet hands as

this can cause electric shock.

• Do not insert ﬁ ngers or other objects into the

air inlet or outlet as the fan rotates at very high

speed and can cause serious injury or damage.

• Do not allow the appliance to operate for long

periods of time with doors or windows open or if

the humidity is very high.

SAVE THESE INSTRUCTIONS!

Important Safety Information

READ AND FOLLOW ALL SAFETY INSTRUCTIONS

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of an

electrical short circuit, grounding reduces the risk of

electric shock by providing an escape wire for the

electric current. The serial rating plate indicates the

voltage and frequency the appliance is designed for.

WARNING - Improper use of the grounding plug can

result in a risk of electric shock. Consult a qualiﬁ ed

electrician or service technician if the grounding

instructions are not completely understood, or if

doubt exists as to whether the appliance is properly

grounded.

FEATURES

will display for 3 seconds when:

• TIMER ON is set

• SWING, TURBO or SLEEP features are turned on

will display for 3 seconds when:

• TIMER OFF is set

• SWING, TURBO or SLEEP features are turned off

will display when anti-cold air feature is turned on

will display when the appliance is defrosting

• In fan mode, the appliance will display the room temperature

• In other modes, the appliance will display the temperature setting

DISPLAY CODE MEANINGS

OPERATING INSTRUCTIONS

OPERATING TEMPERATURE

Optimal performance for the COOL, HEAT and DRY

modes can be achieved in the following temperature

ranges. When the air conditioner is used outside of

these temperature ranges, certain safety protection

features will activate and cause the appliance to

perform less efﬁ ciently.

COOL mode HEAT mode DRY mode

Room temperature

17°C - 32°C

(63°F - 90°F)

0°C - 30°C

(32°F - 86°F)

10°C - 32°C

(50°F - 90°F)

Outdoor temperature

0°C - 50°C

(32°F - 122°F)

-15°C - 30°C

(5°F - 86°F)

0°C - 50°C

(32°F - 122°F)

OPERATION WITHOUT THE REMOTE CONTROL

Note: The manual button is intended for testing

purposes and emergency operation only. Do not

use this function unless absolutely necessary. To

restore regular operation, use the remote control to

activate the appliance.

Operational functioning can be access through the

remote control. In the event that the remote control

fails to work, the appliance can be operated

manually with the manual control button located on

the indoor appliance. Note that manual operation

is not an efﬁ cient long-term solution and that

operating the appliance with the remote control is

recommended.

The appliance must be turned off before manual

operation. To operate the appliance manually:

1. Open the front panel of the indoor appliance.

2. The manual control button is located on the right

side hand side of the appliance.

3. Press the manual control button one time to

activate forced AUTO mode.

4. Press the manual control button a second time to

activate forced COOL mode.

5. Press the manual control button a third time to turn

the appliance off.

6. Ensure the front panel is closed when ﬁ nished.

OPERATING INSTRUCTIONS

To optimize the performance of the appliance:

• Keep doors and windows closed

• Do not block air inlets or outlets

• Regularly inspect and clean all air ﬁ lters

• Limit energy usage by using the timer function

Note: When the outside temperature is below 0°C

(32°F), keep the appliance plugged in at all times

to ensure smooth ongoing performance.

OPERATION WITH THE REMOTE CONTROL

• The air conditioner will not operate if curtains, doors or other materials block the signal from the remote

control to the indoor appliance.

• Do not expose the remote control to water, direct sunlight or excessive heat.

• Do not allow direct sunlight to fall on the infrared receiver on the indoor appliance as this can impede

the signal from the remote control.

• Remote signal reception is conﬁ rmed with a beep.

Remote Control Speciﬁ cations

Model RG57B/BGEU1

Rated Voltage 3.0V (dry batteries R03/LR03x2)

Signal Receiving Range 8m (26 feet)

Environment -5°C to 60°C (23°F to 140°F)

MODE: Selects mode operation in

the following order:

Auto --> Cool --> Dry --> Heat --> Fan

FAN: Selects fan speed in the

following order:

Auto --> Low --> Med --> High

ON/OFF: Turns the appliance

on or off

SLEEP: Conserves energy

during sleeping hours

TURBO: Starts and stops the

turbo function, which will run

the appliance continuously to

reach the preset temperature in

the shortest amount of time; after

running for 30 minutes turbo

mode will stop

LED: Turns the LED

display on or off

TIMER OFF: Used to set

automatic off function

TIMER ON: Used to set

automatic on function

UP AND DOWN BUTTONS:

Used to increase or decrease

the temperature setting in 1°

increments. Press and hold

the up and down buttons for

three seconds to change the

temperature scale between °C

and °F

DIRECT: Used to change

the louver movement and

set the up or down air ﬂ ow

direction

SWING: Used to start or

stop the horizontal louver

swing feature

SHORTCUT: Used to restore

the current settings or resume

previous settings

OPERATING INSTRUCTIONS

Symbol will ﬂ ash

to indicate that the

appliance has received

the signal from the

remote control.

OPERATING MODES

AUTO mode

• Press the MODE button to select AUTO mode.

• The appliance will automatically select cooling,

or fan only operation depending on what

temperature has been set and the ambient room

temperature.

DRY (dehumidifying) mode

• Press the MODE button to select the DRY mode.

• The fan speed cannot be adjusted in this mode.

The fan operates at LOW speed.

• Keep windows and doors closed for the best

dehumidifying effect.

• Condensed water will automatically drain

through the drain hose.

Note: The fan speed cannot be adjusted in AUTO

and DRY mode.

COOL mode / HEAT mode / FAN operation

• Press the MODE button to select the desired

mode; COOL, HEAT or FAN.

• Press the UP or DOWN buttons to select your

desired room temperature. The temperature can

be set within a range of 17°C - 30°C (62°F -

86°F).

• Press the FAN button to choose the fan speed:

Auto, Low, Med or High.

SHORTCUT function (only available on remote):

• Used to save a favourite setting

• Set the unit to the temperature and fan speed that

you would like to set as a favourite

• Press and hold the SHORTCUT button for 2

seconds

• Press the SHORTCUT button at any point in future

to return to the favourite setting

• If no favourite is set, pressing the SHORTCUT

button will cause the unit to run in AUTO mode at

26°C (79°F), with fan speed set to AUTO

Anti-Cold Air Feature

• The fan speed and the louver angle adjust

according to the ambient temperature. The

manual control button and remote control cannot

adjust fan speed or louver angle in this setting.

OPERATING INSTRUCTIONS

SLEEP function

• The SLEEP function is used to decrease energy

use during sleeping hours. This function can only

be activated by pressing the SLEEP button on the

remote control.

• When in COOL mode, the temperature will

increase by 1°C (2°F) in the ﬁ rst hour and will

increase an additional 1°C (2°F) in the second

hour. The appliance will then hold this new

temperature for 5 hours. At the end of the SLEEP

cycle, the appliance will turn off.

• When in HEAT mode, the temperature will

decrease by 1°C (2°F) in the ﬁ rst hour and will

decrease an additional 1°C (2°F) in the second

hour. The appliance will then hold this new

temperature for 5 hours. At the end of the SLEEP

cycle, the appliance will turn off.

Note: The sleep feature is not available in FAN and

DRY mode.

AUTOMATIC FEATURES

Auto-Restart

If the appliance loses power, it will automatically

restart with the previous settings once power is

restored.

Louver Angle Memory

When turning on the appliance, the louver will

automatically resume the previous angle setting.

Refrigerant Leakage Detection

The indoor appliance will automatically display

“EC” when it detects a refrigerant leakage and the

appliance will shut off.

TIMER OPERATION

To set the Auto-off timer:

• Ensure the appliance is turned on

• Press the TIMER OFF button and the Timer Off

indicator will illuminate

• Press the TIMER OFF button to select the desired

amount of hours before the appliance turns off

To set the Auto-on timer:

• Ensure the appliance is turned on

• Press the TIMER ON button and the Timer On

indicator will illuminate

• Press the TIMER ON button to select the desired

amount of hours before the appliance turns on

Notes:

• The TIMER ON and TIMER OFF buttons will

increase the time in 0.5 hour increments up to

10 hours and then in 1 hour increments up to 24

hours

• The display will revert back to showing the

previous temperature setting if the appliance does

not receive a signal within a 5 second period

during programming

• Turning the appliance on or off at any time or

adjusting the timer setting to 0.0 hours will cancel

the TIMER settings

OPERATING INSTRUCTIONS

Using the TIMER ON and TIMER OFF feature at the

same time

The appliance can be set to turn on and run for a

set period of time and then turn off again by using

the TIMER ON and TIMER OFF features at the same

time. Keep in mind that the hours displayed on the

appliance refer to the number of hours that will pass

from the current time before the action is taken.

For example:

• First, set the Auto-off timer

• Ensure the appliance is turned on

• Press the TIMER OFF button and the Timer Off

indicator light will illuminate

• Press the TIMER OFF button to select the desired

amount of hours before the appliance turns off

• Press the TIMER ON button within 5 seconds and

the Timer On indicator light will illuminate

• Press the TIMER ON button to select the amount

of hours before the appliance turns back on

Note: If the TIMER OFF function and the SLEEP

function are used at the same time, the appliance

will only implement the setting whose duration is

shorter.

If the TIMER OFF function is set for less than seven

hours, the TIMER OFF will turn the appliance off

before the SLEEP function can complete its cycle.

If the TIMER OFF function is set for more than seven

hours, the SLEEP function will turn the appliance off

before the TIMER OFF can complete its cycle.

SETTING VERTICAL ANGLE OF AIR FLOW

While the appliance is on, use the SWING/DIRECT

button to set the vertical angle of the air ﬂ ow.

1. Press the SWING/DIRECT button once to

activate the louver. Each press of the button will

adjust the louver by 6°.

2. To make the louver swing up and down

continuously, press and hold the SWING/

DIRECT button for 3 seconds. Press it again to

stop the continuous swing.

SETTING HORIZONTAL ANGLE OF AIR

FLOW

The horizontal angle of the air ﬂ ow must be set

manually. Grip the deﬂ ector rod and manually adjust

it to the preferred direction.

NOTE ON LOUVER ANGLES

When using COOL or DRY mode, do not set the

louver at an extreme vertical angle for a long period

of time. Water can condense on the louver blade

which can then drip on the ﬂ oor or furnishings.

When using COOL or HEAT mode, do not set the

louver at an extreme vertical angle for a long period

of time. This can cause reduced performance due to

restricted air ﬂ ow.

Do not force the louver to move or adjust the louver

by hand. This will cause the louver to be out of sync

and it will not function correctly. If this occurs, turn off

the appliance and unplug it for a few seconds and

then restart the appliance. This will reset the louver

position.

CAUTION

Do not put ﬁ ngers in or near the blower

and suction side of the appliance. The

high-speed fan inside the appliance can

cause serious harm or injury.

OPERATING INSTRUCTIONS

REPLACING THE REMOTE BATTERIES

The appliance comes with two AAA batteries. Place the batteries in the

remote control before use.

1. Slide the back cover from the remote downward to expose the battery

compartment.

2. Insert the batteries, ensure to match the (+) and (-) symbols on the ends

of the batteries with the symbols inside the battery compartment.

3. Slide the battery cover back into place.

• Do not mix old and new batteries or batteries of different types.

• Do not leave the batteries in the remote control if it is not going to be

used for more than 2 months.

• Do not dispose of batteries as unsorted municipal waste. Collection of

such waste separately for special treatment is necessary.

Note: Removing the batteries from the remote will erase all previous

programming. After inserting new batteries, the settings on the appliance

must be reprogrammed.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

1. Reorient or relocate the receiving antenna

2. Increase the separation between the equipment and receiver

3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

4. Consult the dealer or an experienced radio/TV technician for help

Changes or modiﬁ cations not approved by the party responsible for FCC compliance could void the user’s

authority to operate the equipment. This appliance complies with Part 15 of the FCC Rules and Industry

Canada’s license-exempt RSS.

Operation is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept any interference received, including interference that may cause undesired

operation.

This device complies with Canadian CAN ICES-3 (B) / NMB-3 (B)

OPERATING INSTRUCTIONS

CLEANING THE INDOOR APPLIANCE

Note: Always turn off the air conditioner and

disconnect the power source before cleaning the

appliance or removing the ﬁ lter.

• Use a soft, dry cloth to clean the outside of the

appliance. If the appliance is especially dirty,

use a cloth soaked in warm water to clean the

outside of the appliance.

• Do not use water to clean the inside of the

appliance as this can destroy the insulation and

cause electric shock.

• Do not use chemicals or chemically treated cloths

to clean the appliance.

• Do not use benzene, paint thinner or other

solvents to clean the appliance. They can cause

the plastic surface to crack or deform.

• Do not use water hotter than 40°C (104°F) to

clean the front panel. This can cause the panel to

deform or become discoloured.

CLEANING THE AIR FILTER

A clogged air ﬁ lter can reduce the efﬁ ciency of the

air conditioner. It is advisable to clean the air ﬁ lter

every two weeks or after 240 hours of operation,

whichever comes ﬁ rst. When removing the ﬁ lter, do

not touch any metal parts inside the appliance as the

sharp metal edges can cause injury.

1. Lift the front panel of the indoor appliance.

2. Grip the tab on the end of the ﬁ lter, lift it up and

pull it outwards to remove it from the appliance.

3. If the ﬁ lter has a small air freshening ﬁ lter, unclip if

from the larger ﬁ lter. Clean the air freshening ﬁ lter

with a soft brush or hand-held vacuum cleaner.

4. Clean the large ﬁ lter with warm, soapy water.

Use mild detergent.

5. Rinse the ﬁ lter with clean water. Ensure all soap

is removed from the ﬁ lter and shake off excess

water.

6. Dry the ﬁ lter in a cool, dry place. Do not expose

the ﬁ lter to direct sunlight as this can warp or

shrink the ﬁ lter.

7. When the ﬁ lter is dry, replace the air freshening

ﬁ lter and then slide the larger ﬁ lter back into the

appliance.

8. Close the front panel of the indoor appliance.

Note: Do not touch the air freshening (plasma) ﬁ lter

for at least 10 minutes after turning off the appliance

to allow it to cool.

CARE & MAINTENANCE

MAINTENANCE -

LONG PERIODS OF NON USE

If the air conditioner will not be used for a long

period of time, complete the following:

1. Turn on the FAN function until the appliance is

completely dry.

2. Turn off the appliance and disconnect the power.

3. Clean and replace all ﬁ lters.

4. Remove the batteries from the remote control.

MAINTENANCE -

PRE-SEASON INSPECTION

After a long period of non-use or before a period of

frequent use, complete the following:

1. Check for damaged wires.

2. Clean all ﬁ lters.

3. Check for leaks.

4. Replace the remote control batteries.

5. Ensure nothing is blocking air inlets and outlets.

Ensure nothing is in the way of the infrared

remote receiver.

MAINTENANCE AND CLEANING OF THE

OUTDOOR APPLIANCE

Any cleaning, maintenance or repairs of the

outdoor appliance must be completed by a licensed

HVAC technician. Contact the dealer who sold the

appliance for information on maintenance or repairs

to the outdoor appliance.

DISPOSAL

Check for local regulatory compliance regarding the

approved and safe disposal of this appliance.

ERROR CODES

If an error code appears in the display window, the

appliance may stop operation as a safety feature.

Wait approximately 10 minutes as the error may

resolve itself. If the error code persists, disconnect

the power to the appliance, wait approximately 5

minutes and then restore power to the appliance.

If the error persists after the power cycle, contact the

sales center where the appliance was purchased for

information on servicing the appliance.

CARE & MAINTENANCE

PROBLEM POSSIBLE CAUSE

The appliance does not start

when pressing on/off button

• The appliance has a protection feature that prevents it from being turned back

on for 3 minutes after being turned off to avoid overloading

• Room temperature is lower than the set temperature. (Cooling mode)

• Room temperature is higher than the set temperature (Heat mode)

• Power failure

• A fuse is burned out

• Remote control batteries have burned out

The appliance changes from

COOL or HEAT to FAN mode

automatically

• The appliance may change mode to prevent frost from forming on the internal

coils

• The set temperature has been reached, at which point the compressor is

turned off. The appliance will continue operating when the room temperature

ﬂ uctuates from the set temperature

The indoor or outdoor

appliance are emitting white

mist

• In humid regions, a large temperature difference between the room

temperature and the set temperature can cause white mist

• When the appliance restarts in HEAT mode after defrosting, white mist may

be emitted due to moisture generated from the defrosting process

The indoor or outdoor

appliance are making noise

• A rushing air sound may occur when the louver resets its position

• A squeaking sound may occur after running the appliance in HEAT mode due

to the expansion and contraction of internal plastic parts

• A low hissing sound during operation is normal; this is caused by refrigerant

gas ﬂ owing through the appliance

Dust is emitted from the

appliance

• The appliance may accumulate dust on the internal components during long

periods of non-use, which will be emitted when the appliance is turned on

The appliance emits a bad

odor

• The appliance may absorb odors from the surrounding environment, (cooking

smells, animal smells, cigarette smells, etc.) which will be emitted during

operation

• The ﬁ lter has become clogged and should be cleaned

The fan of the outdoor

appliance does not operate

• During operation, the fan speed on the outdoor appliance is controlled to

optimize product efﬁ ciency

Operation is erratic,

unpredictable, or appliance is

unresponsive

• Interference from cell phone towers and remote boosters may cause the

appliance to malfunction. To reset the appliance: disconnect the power then

reconnect and press the power button to restart operation

Poor cooling or heating

performance

• Temperature setting is higher or lower than the ambient room temperature

• The outdoor temperature is extremely high or low

• The air ﬁ lter is clogged

• The air inlet or outlet is blocked

• Doors and windows are open

• Low refrigerant due to leak or long-term use

• The heat exchanger is dirty

The appliance starts and stops

frequently

• There is too much or too little refrigerant in the system

• Incompressible gas or moisture has entered the system

• The voltage is too high or too low

• The compressor is malfunctioning

Danby consumer care: 1-800-263-2629

Hours of operation:

Monday to Thursday 8:30 am - 6:00 pm Eastern Standard Time

Friday 8:30 am - 4:00 pm Eastern Standard Time

Information in this manual is subject to change without notice.

TROUBLESHOOTING

LIMITED IN-HOME APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is used under the normal operating

conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or Danby Products Inc. (U.S.A.) (hereafter

“Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.

First Year

During the rst twelve (12) months, any functional parts of this product found to be defective, will be repaired or replaced, at warrantor’s

option, at no charge to the ORIGINAL purchaser.

To obtain

Danby reserves the right to limit the boundaries of “In Home Service” to the proximity of an Authorized Service Depot. Any app liance

Service

requiring service outside the limited boundaries of “In Home Service” , it will be the consumer’s responsibility to transport the appliance (at

their own expense) to the original retailer (point of purchase) or a service depot for repair. See “Boundaries of In Home Serv ice” below.

Contact your dealer from whom your unit was purchased, or contact your nearest authorized Danby service depot, where service

must be performed by a qualied service technician.

If service is performed on the units by anyone other than an authorized service depot, or the unit is used for commercial appli cation, all

obligations of Danby under this warranty shall be void.

Boundaries of

If the appliance is installed in a location that is 100 kilometers (62 miles) or more from the nearest service center your unit must be

In Home Service

delivered to the nearest authorized Danby Service Depot, as service must only be performed by a technician qualied and certif ied for

warranty service by Danby. Transportation charges to and from the service location are not protected by this warranty and are t he

responsibility of the purchaser.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other c ontents of this appliance, whether due

to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, Danby, there are no other warranties, conditions, representations or guarantees, express or implied, m ade or intended by Danby or its

authorized distributors and all other warranties, conditions, representations or guarantees, including any warranties, conditio ns, representations or guarantees

under any Sale of Goods Act or like legislation or statue is hereby expressly excluded. Save as herein provided, Danby shall no t be responsible for any damages

to persons or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction o f the unit and by the purchase of

the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for damages to persons or propert y caused by the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating con ditions

(extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, oods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for out door application).

Proof of purchase date will be required for warranty claims; so, please retain bills of sale. In the event warranty service is required, present this document to our

AUTHORIZED SERVICE DEPOT.

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

04/09

1-800-263-2629

Warranty Service

In-home

During the first twelve (12) months, any functional parts of this product found to be defective, will be

replaced, at warrantor’s option, at no charge to the ORIGINAL purchaser.

First 12 months

LIMITED APPLIANCE WARRANTY

This quality product is warranted to be free from manufacturer’s defects in material and workmanship, provided that the unit is

used under the normal operating conditions intended by the manufacturer.

This warranty is available only to the person to whom the unit was originally sold by Danby Products Limited (Canada) or

Danby Products Inc. (U.S.A.) (hereafter “Danby”) or by an authorized distributor of Danby, and is non-transferable.

TERMS OF WARRANTY

Plastic parts, are warranted for thirty (30) days only from purchase date, with no extensions provided.

Nothing within this warranty shall imply that Danby will be responsible or liable for any spoilage or damage to food or other

contents of this appliance, whether due to any defect of the appliance, or its use, whether proper or improper.

EXCLUSIONS

Save as herein provided, by Danby, there are no other warranties, conditions, representations or guarantees, express or

implied, made or intended by Danby or its authorized distributors and all other warranties, conditions, representations or

guarantees, including any warranties, conditions, representations or guarantees under any Sale of Goods Act or like legislation

or statute is hereby expressly excluded. Save as herein provided, Danby shall not be responsible for any damages to persons

or property, including the unit itself, howsoever caused or any consequential damages arising from the malfunction of the unit

and by the purchase of the unit, the purchaser does hereby agree to indemnify and hold harmless Danby from any claim for

damages to persons or property caused by the unit.

GENERAL PROVISIONS

No warranty or insurance herein contained or set out shall apply when damage or repair is caused by any of the following:

1) Power failure.

2) Damage in transit or when moving the appliance.

3) Improper power supply such as low voltage, defective house wiring or inadequate fuses.

4) Accident, alteration, abuse or misuse of the appliance such as inadequate air circulation in the room or abnormal operating

conditions (extremely high or low room temperature).

5) Use for commercial or industrial purposes (ie. If the appliance is not installed in a domestic residence).

6) Fire, water damage, theft, war, riot, hostility, acts of God such as hurricanes, floods etc.

7) Service calls resulting in customer education.

8) Improper Installation (ie. Building-in of a free standing appliance or using an appliance outdoors that is not approved for

outdoor application).

Proof of purchase date will be required for warranty claims; please retain bills of sale.

Danby Products Limited

PO Box 1778, Guelph, Ontario, Canada N1H 6Z9

Telephone: (519) 837-0920 FAX: (519) 837-0449

Danby Products Inc.

PO Box 669, Findlay, Ohio, U.S.A. 45840

Telephone: (419) 425-8627 FAX: (419) 425-8629

1-800-263-2629

03/17

EXIGENCES DE SÉCURITÉ

Pour éviter les difﬁ cultés d’installation ou d’utilisation,

lisez ces instructions avant la première utilisation du

produit.

• Utilisez cet appareil uniquement pour son usage

prévu, tel que décrit dans ce manuel.

• Ne laissez jamais les enfants utiliser, jouer ou

ramper à l’intérieur de l’appareil.

• Ne jamais nettoyer les pièces de l ‘appareil avec

des ﬂ uides inﬂ ammables. Les fumées peuvent

créer un risque d’incendie ou une explosion.

• Ne pas entreposer ou utiliser des vapeurs ou des

liquides inﬂ ammables à proximité de cet appareil

ou de tout autre appareil. Les fumées peuvent

créer un risque d’incendie ou une explosion.

• Ne pas utiliser ce produit près de l’eau, p. Dans

un sous-sol humide, buanderie ou près d’un évier.

• Ne pas couvrir ou bloquer les ouvertures de

l’appareil.

• Cet appareil ne doit être entretenu que par un

technicien HVAC qualiﬁ é. Contacter le revendeur

à l’endroit où l’appareil a été acheté pour des

informations sur l’entretien de l’appareil.

• L’élimination de cet appareil doit être conforme

aux règlements fédéraux et locaux.

• Cet appareil n’est pas destiné à être utilisé par

des personnes (y compris des enfants) dont les

capacités physiques, sensorielles ou mentales

peuvent être différentes ou réduites, ou qui

manquent d’expérience ou de connaissances,

sauf si ces personnes reçoivent une supervision

ou une formation pour faire fonctionner l’appareil

par une personne responsable de leur sécurité.

• Ne pas monter ou placer des objets sur le dessus

de l’appareil extérieur.

• Ne faites pas fonctionner cet appareil avec des

mains mouillées car cela peut provoquer un choc

électrique.

Consignes de sécurité importantes

LIRE ET SUIVRE TOUTES LES INSTRUCTIONS DE SÉCURITÉ

GARDER CES INSTRUCTIONS!

• N’insérez pas de doigts ou d’autres objets dans

l’entrée ou la sortie d’air car le ventilateur tourne

à très grande vitesse et peut causer des blessures

graves ou des dommages.

• Ne laissez pas l’appareil fonctionner pendant de

longues périodes avec des portes ou des fenêtres

ouvertes ou si l’humidité est très élevée.

INSTRUCTIONS DE MISE À LA TERRE

Cet appareil doit être mis à la terre. En cas de

courtcircuit, la mise à la terre réduit les risques de

décharge électrique en fournissant un échappatoire

au courant électrique. Le voltage et la fréquence

requis pour cet appareil sont indiqués sur la plaque

d’identiﬁ cation

AVERTISSEMENT - Une ﬁ che de mise à la terre mal

branchée peut entraîner un risque d’incendie, de

choc électrique ou de blessures aux personnes qui

utilisent l’appareil. Si vous n’êtes pas certain que

l’appareil est correctement mis à la terre, consultez

un préposé du service qualiﬁ é.

CARACTÉRISTIQUES

afﬁ che pendant 3 secondes lorsque:

• TIMER ON est réglé

• les fonctions SWING, TURBO ou SLEEP sont activées

afﬁ che pendant 3 secondes lorsque:

• TIMER OFF est réglé

• les fonctions SWING, TURBO ou SLEEP sont désactivées

afﬁ che lorsque du fonction anti-air froid est activee

afﬁ che si l’appareil est dégivrage

• En mode ventilateur, l’appareil afﬁ che la température ambiante

• Dans les autres modes, l’appareil afﬁ che le réglage de la température

SIGNIFICATIONS DES CODES D’AFFICHAGE

Persienne

CONSIGNES D’UTILISATION

TEMPÉRATURE DE FONCTIONNEMENT

Des performances optimales pour les modes COOL,

HEAT et DRY peuvent être obtenues dans les plages

de températures suivantes. Lorsque le climatiseur

est utilisé hors de cet gamme de températures,

certaines caractéristiques de sécurité seront activés

et causeront un fonctionnement moins efﬁ cace dans

l’appareil.

Mode COOL Mode HEAT Mode DRY

Température ambiante

17°C - 32°C

(63°F - 90°F)

0°C - 30°C

(32°F - 86°F)

10°C - 32°C

(50°F - 90°F)

Température extérieure

0°C - 50°C

(32°F - 122°F)

-15°C - 30°C

(5°F - 86°F)

0°C - 50°C

(32°F - 122°F)

FONCTIONNEMENT SANS TÉLÉCOMMANDE

Remarque: Le bouton manuel est destiné

uniquement aux essais et aux opérations

d’urgence. N’utilisez pas cette fonction à

moins d’être absolument nécessaire. Pour

rétablir un fonctionnement régulier, utilisez

la télécommande pour activer l’appareil.

Le fonctionnement peut être accessible via la

télécommande. Si la télécommande ne fonctionne

pas, l’appareil peut être actionné manuellement avec

le bouton de commande manuelle situé sur l’appareil

intérieur. Notez que le fonctionnement manuel

n’est pas une solution efﬁ cace à long terme et que

l’utilisation de l’appareil avec la télécommande est

recommandée.

L ‘appareil doit être éteint avant l’ utilisation

manuelle. Pour faire fonctionner l’appareil

manuellement:

1. Ouvrez le panneau avant de l’appareil intérieur.

2. Le bouton de commande manuelle se trouve sur

le côté droit de l’appareil.

3. Appuyer une fois sur le bouton de commande

manuelle pour activer le mode AUTO forcé.

4. Appuyer une seconde fois sur le bouton de

commande manuelle pour activer le mode

COOL forcé.

5. Appuyez une troisième fois sur le bouton de

commande manuelle pour éteindre l’appareil.

6. Assurez-vous que le panneau avant est fermé

lorsqu’il est terminé.

Bouton de commande manuelle

CONSIGNES D’UTILISATION

Pour optimiser les performances de l’appareil:

• Gardez les portes et fenêtres fermées

• Ne pas obstruer les entrées ou les sorties d’air

• Inspecter et nettoyer régulièrement tous les ﬁ ltres

à air

• Limiter l’utilisation d’énergie en utilisant la fonction

de minuterie

Remarque: Lorsque la température extérieure est

inférieure à 0°C (32°F), maintenez l’appareil

branché à tout moment pour assurer un bon

fonctionnement continu.

FONCTIONNEMENT AVEC LA TÉLÉCOMMANDE

• Le climatiseur ne fonctionnera pas si des rideaux, des portes ou d’autres matériaux bloquent le signal de

la télécommande vers l’appareil intérieur.

• N’exposez pas la télécommande à l’eau, à la lumière directe du soleil ou à une chaleur excessive.

• Ne laissez pas la lumière directe du soleil tomber sur le récepteur infrarouge de l’appareil intérieur car

cela peut entraver le signal de la télécommande.

• La réception du signal à distance est conﬁ rmée par un bip.

Caractéristiques de la télécommande

Modèle RG57B/BGEU1

Tension nominale 3.0V (piles sèches R03/LR03x2)

Plage de réception du signal 8m (26 pieds)

Environnement -5°C to 60°C (23°F to 140°F)

MODE: Sélectionne le mode de

fonctionnement dans l’ordre suivant:

AUTO --> COOL --> DRY --> HEAT

--> FAN

FAN: Sélectionne la vitesse du

ventilateur dans l’ordre suivant:

Auto --> Bas --> Moyen --> Haute

ON/OFF: Active ou désactive

l’appareil

SLEEP: Conserve l’énergie

pendant les heures de sommeil

LED: Active ou désactive

l’afﬁ chage LED

TIMER OFF: Permet de régler

la fonction de désactivation

automatique

TIMER ON: Permet de régler

la fonction de mise en

marche automatique

BOUTONS HAUT ET BAS: Permet

d’augmenter ou de diminuer le

réglage de la température par

incréments de 1°. Appuyez et

maintenez les boutons haut et

bas pendant trois secondes pour

changer l’échelle de température

entre ° C et ° F

DIRECT: Utilisé pour

changer le mouvement du

déﬂ ecteur et régler le sens

d’écoulement d’air vers le

haut ou vers le bas

SWING: Utilisé pour démarrer

ou arrêter la fonction horizontale

du déﬂ ecteur

CONSIGNES D’UTILISATION

TURBO: Démarre et arrête la

fonction turbo, qui exécutera

l’appareil en continu pour

atteindre la température

préréglée dans le plus court laps

de temps; Après avoir fonctionné

pendant 30 minutes, le mode

turbo s’arrêtera

SHORTCUT: Utilisé pour

restaurer les paramètres actuels

ou reprendre les paramètres

précédents

Le symbole clignotera

pour indiquer que

l’appareil a reçu

le signal de la

télécommande.

MODES DE FONCTIONNEMENT

Mode AUTO (automatique)

• Appuyez sur le bouton MODE pour sélectionner le

mode AUTO.

• L’appareil sélectionnera automatiquement le

refroidissement ou le fonctionnement du ventilateur

uniquement en fonction de la température réglée et

de la température ambiante.

Mode DRY (déshumidiﬁ cation)

• Appuyez sur le bouton MODE pour sélectionner le

mode DRY.

• TLa vitesse ne peuvent pas être réglées dans ce

mode. Le ventilateur fonctionne à basse vitesse.

• Gardez les fenêtres et les portes fermées pour obtenir

le meilleur effet de déshumidiﬁ cation.

• L’eau condensée s’écoule automatiquement à travers

le tuyau de vidange.

Remarque: La vitesse du ventilateur ne peut pas être

réglée en mode AUTO et DRY.

Mode COOL (refroidir) / Mode HEAT (chaleur) /

Fonction FAN (ventilateur)

• Appuyez sur le bouton MODE pour sélectionner le

mode désiré; COOL, HEAT ou FAN.

• Appuyez sur les boutons HAUT ou BAS pour

sélectionner la température ambiante désirée. La

température peut être réglée dans 17°C - 30°C

(62°F - 86°F).

• Appuyez sur le bouton FAN pour choisir la vitesse du

ventilateur: Auto, Low, Med ou High.

SHORTCUT fonction (uniquement disponible sur la

télécommande):

• Utilisé pour enregistrer un paramètre favori

• Réglez l’appareil sur la température et la vitesse du

ventilateur que vous souhaitez régler comme favori

• Maintenez la touche SHORTCUT enfoncée pendant 2

secondes

• Appuyez sur le bouton SHORTCUT à tout moment

pour revenir au réglage préféré

• Si aucun favori n’est réglé, le fait d’appuyer sur la

touche SHORTCUT fera fonctionner l’appareil en

mode AUTO à 26 °C (79 °F), avec la vitesse du

ventilateur réglée sur AUTO

Fonction anti-air froid

• La vitesse du ventilateur et l’angle du déﬂ ecteur

s’ajustent en fonction de la température ambiante. Le

bouton de commande manuelle et la télécommande

ne peuvent pas régler la vitesse du ventilateur ou

l’angle du déﬂ ecteur dans ce réglage.

CARACTÉRISTIQUES AUTOMATIQUES

Redémarrage automatique

Si l’appareil perd le courant, il redémarre

automatiquement avec les réglages précédents une

fois que l’alimentation est rétablie.

Mémoire d’angle de déﬂ ecteur

Lorsque vous allumez l’appareil, le déﬂ ecteur reprend

automatiquement le réglage d’angle précédent.

Détection de fuites de réfrigérant

L’appareil intérieur afﬁ che automatiquement “EC”

lorsqu’il détecte une fuite de réfrigérant et que

l’appareil s’éteint.

CONSIGNES D’UTILISATION

Fonction SLEEP (sommeil)

• La fonction SLEEP est utilisée pour réduire la

consommation d’énergie pendant les heures

de sommeil. Cette fonction ne peut être activée

qu’en appuyant sur le bouton SLEEP de la

télécommande.

• En mode COOL, la température augmentera de

1°C (2°F) dans la première heure et augmentera

1°C supplémentaire (2°F) dans la deuxième

heure. L’appareil maintiendra cette nouvelle

température pendant 5 heures. À la ﬁ n du cycle

SLEEP, l’appareil s’éteindra.

• En mode HEAT, la température diminue de 1°C

(2°F) dans la première heure et diminuera 1°C

supplémentaire (2°F) dans la deuxième heure.

L’appareil maintiendra cette nouvelle température

pendant 5 heures. À la ﬁ n du cycle SLEEP,

l’appareil s’éteindra.

Remarque: la fonction de sommeil n’est pas

disponible en mode FAN et DRY.

FONCTIONNEMENT DU MINUTEUR

Pour régler la minuterie d’arrêt automatique:

• Assurez-vous que l’appareil est sous tension

• Appuyez sur la touche TIMER OFF et l’indicateur

Timer Off s’allume

• Appuyez sur la touche TIMER OFF pour

sélectionner le nombre d’heures avant que

l’appareil ne s’éteigne

Pour régler la minuterie de mise en marche

automatique:

• Assurez-vous que l’appareil est sous tension

• Appuyez sur la touche TIMER ON et l’indicateur

Timer On s’allume

• Appuyez sur la touche TIMER ON pour

sélectionner le nombre d’heures avant que

l’appareil ne s’allume

Remarques:

• Les boutons TIMER ON et TIMER OFF

augmentent le temps par incréments de 0,5

heure jusqu’à 10 heures, puis par incréments de

1 heure jusqu’à 24 heures

• L’afﬁ chage revient à l’afﬁ chage de la température

précédente si l’appareil ne reçoit pas de signal

pendant une période de 5 secondes pendant la

programmation

• Active ou désactive l’appareil à tout moment ou

ajuster le réglage de la minuterie à 0,0 heures

annule les réglages de la TIMER

Utilisation simultanée des fonctions TIMER ON et

TIMER OFF

L’appareil peut être réglé pour s’allumer et

fonctionner pendant un certain temps, puis à

nouveau désactivé en utilisant les fonctions Auto-on

et Auto-off en même temps. Gardez à l’esprit que

les heures afﬁ chées sur l’appareil se rapportent au

nombre d’heures qui passent de l’heure actuelle

avant que l’action soit prise.

Par exemple:

• Commencez par régler la minuterie d’arrêt

automatique

• Assurez-vous que l’appareil est sous tension

• Appuyez sur la touche TIMER OFF et le voyant

Timer Off s’allume

• Appuyez sur la touche TIMER OFF pour

sélectionner le nombre d’heures avant que

l’appareil ne s’éteigne

• Appuyez sur la touche TIMER ON dans les 5

secondes qui suivent et le voyant de la minuterie

s’allume

• Appuyez sur la touche TIMER ON pour

sélectionner le nombre d’heures avant que

l’appareil ne se rallume

Remarque: Si la fonction TIMER OFF et la fonction

SLEEP sont utilisées en même temps, l’appareil ne

mettra en œuvre que le réglage dont la durée est

plus courte.

Si la fonction TIMER OFF est réglée pour moins de

sept heures, la TIMER OFF éteint l’appareil avant que

la fonction SLEEP puisse terminer son cycle.

Si la fonction TIMER OFF est réglée pour plus de sept

heures, la fonction SLEEP éteindra l’appareil avant

que le TIMER OFF ne puisse terminer son cycle.

CONSIGNES D’UTILISATION

La page charge ...

Danby DAS240BAHWDB Le manuel du propriétaire

Marque: Danby

Modèle: DAS240BAHWDB

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Danby DAS240BAHWDB Owner's manual
español: Danby DAS240BAHWDB El manual del propietario

Documents connexes

Autres documents

MRCOOL DIY-36-HP-230AE Manuel utilisateur