Wacker Neuson BS60-4As Manuel utilisateur

Operator’s Manual

Notice d'emploi

Vibratory Rammer

Pilonneuse

BS50-4s, BS50-4As

BS60-4s, BS60-4As

BS70-4As

Type

BS50-4s, BS50-4As, BS60-4s,

BS60-4As, BS70-4As

Document 5200017353

Date

0917

Version

09

Language EN-FR

5200017353

Copyright notice

All rights, including copying and distribution rights, are reserved.

This publication may be photocopied by the original purchaser of the

machine. Any other type of reproduction is prohibited without express

written permission from Wacker Neuson Production Americas LLC.

Any type of reproduction or distribution not authorized by Wacker

Neuson Production Americas LLC represents an infringement of valid

copyrights. Violators will be prosecuted.

Trademarks

All trademarks referenced in this manual are the property of their

respective owners.

Manufacturer

Wacker Neuson Production Americas LLC

N92W15000 Anthony Avenue

Menomonee Falls, WI 53051 U.S.A.

Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957

www.wackerneuson.com

Original instructions

This Operator’s Manual presents the original instructions. The original

language of this Operator’s Manual is American English.

wc_tx003624gb_FM10.fm

3

Rammer

Foreword

SAVE THESE INSTRUCTIONS—This manual contains important instructions for

the machine models below. These instructions have been written expressly by

Wacker Neuson Production Americas LLC and must be followed during installation,

operation, and maintenance of the machines.

Machine

identification

A nameplate listing the model number, item number, revision number, and serial

number is attached to this machine. The location of the nameplate is shown above.

Serial number

(S/N)

For future reference, record the serial number in the space provided below. You will

need the serial number when requesting parts or service for this machine.

Machine

documentation

■ From this point forward in this documentation, Wacker Neuson Production

Americas LLC will be referred to as Wacker Neuson.

■ Keep a copy of the Operator’s Manual with the machine at all time

s.

■ Fo

r spare parts information, please see your Wacker Neuson Dealer, or visit

the

W

acker Neuson website at http://www.wackerneuson.com/.

■ When ordering parts or requesting service information, be prepared to

provide

the machine model number, item number, revision number, and serial number.

Machine Item Number

BS 50-4s, BS 50-4As 5200000644, 5200000662, 5200000679, 5200000680,

5200018226, 5200018219, 5100015099, 5100025357,

5100027197

BS 60-4s, BS 60-4As 5200000647, 5200000648, 5200000667, 5200000668,

5200000674, 5200000675, 5200014910, 5200018231,

5200018232, 5200018233, 5200022984, 5100015123,

5100027198

BS 70-4As 5100015124, 5100015126, 5100027199

wc_gr011588

Serial Number:

wc_tx003624gb_FM10.fm

4

Rammer

Foreword

Expectations

for

information in

this manual

■ This manual provides information and procedures to safely operate and

maintain the above Wacker Neuson model(s). For your own safety and to

reduce the risk of injury, carefully read, understand, and observe all instructions

described in this manual.

■ Wacker Neuson expressly reserves the right to make technical modifications,

even without notice, which improve the performance or safety standards of its

machines.

■ The information contained in this manual is based on machines manufactured

up until the time of publication. Wacker Neuson reserves the right to change any

portion of this information without notice.

■ The illustrations, parts, and procedures in this manual refer to Wacker Neuson

factory-installed components. Your machine may vary depending on the

requirements of your specific region.

CALIFORNIA

Proposition

65 Warning

Combustion exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to the State of California to cause cancer and

birth defects or other reproductive harm.

Laws

pertaining to

spark

arresters

NOTICE: State Health Safety Codes and Public Resources Codes specify that in

certain locations spark arresters be used on internal combustion engines that use

hydrocarbon fuels. A spark arrester is a device designed to prevent accidental

discharge of sparks or flames from the engine exhaust. Spark arresters are

qualified and rated by the United States Forest Service for this purpose. In order to

comply with local laws regarding spark arresters, consult the engine distributor or

the local Health and Safety Administrator.

Manufacturer’s

approval

This manual contains references to approved parts, attachments, and

modifications. The following definitions apply:

■ Approved parts or attachments are those either manufactured or provided by

Wacker Neuson.

■ Approved modifications are those performed by an authorized Wacker

Neuson service center according to written instructions published by Wacker

Neuson.

■ Unapproved parts, attachments, and modifications are those that do not

meet the approved criteria.

Unapproved parts, attachments, or modifications may have the following

consequences:

■ Serious injury hazards to the operator and persons in the work area

■ Permanent damage to the machine which will not be covered under warranty

Contact your Wacker Neuson dealer immediately if you have questions about

approved or unapproved parts, attachments, or modifications.

2016-CE-BS50-4s_Honda_en_FM10.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin 53051 USA

Product

Product category

Product function

Item number

Net installed power

Measured sound power level

Guaranteed sound power level

BS50-4As

Vibratory Rammer

To compact soil

5200018219 5100015099

5100027197

2.35 kW 2.70 kW

103 db(A) 104 db(A)

108 db(A)

Conformity Assessment Procedure

According to 2000/14/EC ANNEX VIII

Notified Body

Lloyds Register Verification Limited (Notified Body No 0038)

71 Fenchurch Street, London EC3M 4BS, United Kingdom

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2000/14/EC, 2005/88/EC, 2014/30/EU, EN 500-1, EN 500-4

Authorized Person for Technical Documents

Robert Raethsel, Wacker Neuson Produktion GmbH & Co. KG, Wackerstrasse 6,

85084 Reichertshofen, Germany

Menomonee Falls, WI, USA, 03.01.17

Original Declaration of Conformity

Keith Herr

Vice President and Managing Director

For Wacker Neuson

Paul Sina

Manager, Product Engineering

For Wacker Neuson

Jeff Volden

Director, Product Engineering

For Wacker Neuson

2016-CE-BS50-4s_Robin_en_FM10.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin 53051 USA

Product

Product category

Product function

Item number

Net installed power

Measured sound power level

Guaranteed sound power level

BS50-4s

Vibratory Rammer

To compact soil

5200000662

2.4 kW

103 dB(A)

108 dB(A)

Conformity Assessment Procedure

According to 2000/14/EC ANNEX VIII

Notified Body

Lloyds Register Verification Limited (Notified Body No 0038)

71 Fenchurch Street, London EC3M 4BS, United Kingdom

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2000/14/EC, 2005/88/EC, 2014/30/EU, EN 500-1, EN 500-4

Authorized Person for Technical Documents

Robert Raethsel, Wacker Neuson Produktion GmbH & Co. KG, Wackerstrasse 6,

85084 Reichertshofen, Germany

Original Declaration of Conformity

Menomonee Falls, WI, USA, 03.01.17

Keith Herr

Vice President and Managing Director

For Wacker Neuson

Paul Sina

Manager, Product Engineering

For Wacker Neuson

Jeff Volden

Director, Product Engineering

For Wacker Neuson

2016-CE-BS60-4s_Honda_en_FM10.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin 53051 USA

Product

Product category

Product function

Item number

Net installed power

Measured sound power level

Guaranteed sound power level

BS60-4As

Vibratory Rammer

To compact soil

5200018232, 5200018233 5100015123

5100027198

2.35 kW 2.7 kW

104 db(A)

108 db(A)

Conformity Assessment Procedure

According to 2000/14/EC ANNEX VIII

Notified Body

Lloyds Register Verification Limited (Notified Body No 0038)

71 Fenchurch Street, London EC3M 4BS, United Kingdom

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2000/14/EC, 2005/88/EC, 2014/30/EU, EN 500-1, EN 500-4

Authorized Person for Technical Documents

Robert Raethsel, Wacker Neuson Produktion GmbH & Co. KG, Wackerstrasse 6,

85084 Reichertshofen, Germany

Menomonee Falls, WI, USA, 03.01.17

Original Declaration of Conformity

Keith Herr

Vice President and Managing Director

For Wacker Neuson

Paul Sina

Manager, Product Engineering

For Wacker Neuson

Jeff Volden

Director, Product Engineering

For Wacker Neuson

2016-CE-BS60-4s_Robin_en_FM10.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin 53051 USA

Product

Product category

Product function

Item number

Net installed power

Measured sound power level

Guaranteed sound power level

BS60-4s

Vibratory Rammer

To compact soil

5200000667, 5200000675, 5200000674, 5200000668

2.4 kW

102 dB(A)

108 dB(A)

Conformity Assessment Procedure

According to 2000/14/EC ANNEX VIII

Notified Body

Lloyds Register Verification Limited (Notified Body No 0038)

71 Fenchurch Street, London EC3M 4BS, United Kingdom

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2000/14/EC, 2005/88/EC, 2014/30/EU, EN 500-1, EN 500-4

Authorized Person for Technical Documents

Robert Raethsel,

Wacker Neuson Produktion GmbH & Co. KG,

Wackerstrasse 6

,

85084 Reichertshofen, Germany

Original Declaration of Conformity

Menomonee Falls, WI, USA, 03.01.17

Keith Herr

Vice President and Managing Director

For Wacker Neuson

Paul Sina

Manager, Product Engineering

For Wacker Neuson

Jeff Volden

Director, Product Engineering

For Wacker Neuson

2016-CE-BS70-4s_Honda_en_FM10.fm

EC Declaration of Conformity

Manufacturer

Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,

Menomonee Falls, Wisconsin 53051 USA

Product

Product category

Product function

Item number

Net installed power

Measured sound power level

Guaranteed sound power level

BS70-4As

Vibratory Rammer

To compact soil

5100015124, 5100027199

2.7 kW

104 db(A)

108 db(A)

Conformity Assessment Procedure

According to 2000/14/EC ANNEX VIII

Notified Body

Lloyds Register Verification Limited (Notified Body No 0038)

71 Fenchurch Street, London EC3M 4BS, United Kingdom

Directives and Standards

We hereby declare that this product meets and complies with the relevant regulations and

requirements of the following directives and standards:

2006/42/EC, 2000/14/EC, 2005/88/EC, 2014/30/EU, EN 500-1, EN 500-4

Authorized Person for Technical Documents

Robert Raethsel, Wacker Neuson Produktion GmbH & Co. KG, Wackerstrasse 6,

85084 Reichertshofen, Germany

Menomonee Falls, WI, USA, 03.01.17

Original Declaration of Conformity

Keith Herr

Vice President and Managing Director

For Wacker Neuson

Paul Sina

Manager, Product Engineering

For Wacker Neuson

Jeff Volden

Director, Product Engineering

For Wacker Neuson

Table of Contents

Rammer

wc_bo5200015017_09TOC.fm

15

Foreword 3

EC Declaration of Conformity 5

1 Safety Information 17

1.1 Signal Words Used in this Manual ..................................................... 17

1.2 Machine Description and Intended Use ............................................. 18

1.3 Safety Guidelines for Operating the Machine ..................................... 19

1.4 Safety Guidelines for Lifting the Machine ........................................... 20

1.5 Service Safety .................................................................................... 21

1.6 Operator Safety while Using Internal Combustion Engines ............... 23

2 Labels 24

2.1 Label Locations .................................................................................. 24

2.2 Label Meanings .................................................................................. 25

3 Lifting and Transporting 29

3.1 Lifting the Rammer ............................................................................. 29

3.2 Transporting the Rammer .................................................................. 30

4 Operation 33

4.1 Preparing the Machine for First Use ................................................... 33

4.2 Recommended Fuel ........................................................................... 33

4.3 Refueling the Machine ........................................................................ 34

4.4 Position of the Operator ..................................................................... 35

4.5 Before Starting ................................................................................... 35

4.6 Starting, Operating, and Stopping the Machine—WM 100 ................ 36

4.7 Starting, Operating, and Stopping the Machine—Honda ................... 38

4.8 Low Oil Shut-Off Switch—WM100 ..................................................... 40

4.9 Low Oil Shut-Off Switch—Honda ....................................................... 41

4.10 Emergency Shutdown Procedure ....................................................... 41

4.11 Optional Equipment ............................................................................ 42

5 Maintenance 43

5.1 Maintaining the Emission Control System .......................................... 43

5.2 Periodic Maintenance Schedule ......................................................... 44

5.3 Servicing the Air Cleaner .................................................................... 45

Table of Contents

Rammer

wc_bo5200015017_09TOC.fm

16

5.4 Checking the Fuel Lines and Fittings ..................................................46

5.5 Maintaining the Shoe Hardware ..........................................................47

5.6 Inspecting the Machine .......................................................................48

5.7 Cleaning the Engine Cooling Fins .......................................................49

5.8 Cleaning and Checking the Spark Plug ...............................................50

5.9 Checking and Changing the Engine Oil ..............................................51

5.10 Checking and Changing the Ramming System Oil .............................53

5.11 Inspecting and Cleaning the Fuel Filter ...............................................55

5.12 Replacing the In-Line Fuel Filter Assembly .........................................56

5.13 Long-Term Storage .............................................................................57

5.14 Machine Disposal / Decommissioning .................................................58

6 Troubleshooting 59

7 Technical Data 60

7.1 BS 50-4s ..............................................................................................60

7.2 BS 50-4As ...........................................................................................61

7.3 BS 60-4s ..............................................................................................62

7.4 BS 60-4As ...........................................................................................63

7.5 BS 70-4As ...........................................................................................64

7.6 Sound Measurements .........................................................................65

7.7 Vibration Measurements .....................................................................66

7.8 Dimensions ..........................................................................................67

8 Emission Control Systems Information

and Warranty—Gasoline 69

8.1 Emission Control System Background Information .............................69

8.2 Limited Defect Warranty for Exhaust Emission Control System .........70

8.3 Limited Defect Warranty for Wacker Neuson Evaporative

Emission Control Systems ..................................................................70

wc_si000836gb_FM10.fm

17

Rammer

Safety Information

1 Safety Information

1.1 Signal Words Used in this Manual

This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE

signal words which must be followed to reduce the possibility of personal injury,

damage to the equipment, or improper service.

NOTICE: Used without the safety alert symbol, NOTICE in

dicates a situation

which, if not avoided, could result in property damage.

Note: A Note contains additional information important to a procedure.

This is the safety alert symbol. It is used to alert you to potential personal hazards.

► Obey all safety messages that follow this symbol.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will result in death

or serious injury.

► To avoid death or serious injury from this type of hazard, obey all safety mes-

sages that follow this signal word.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could result in

death or serious injury.

► To avoid possible death or serious injury from this type of hazard,

obey all safety

messages that follow this signal word.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could result in

minor or moderate injury.

► To avoid possible minor or moderate injury from this type of hazard,

obey all

safety messages that follow this signal word.

wc_si000836gb_FM10.fm

18

Rammer

Safety Information

1.2 Machine Description and Intended Use

This machine is a vibratory rammer. The Wacker Neuson Rammer consists of a

gasoline or diesel engine, a clutch, a fuel tank, a spring-loaded ramming system, a

ramming shoe, and a handle. The engine transmits power through the ramming

system and ramming shoe, generating percussive impact force to compact soil.

The operator guides and controls the machine from behind using the handle.

This machine is intended to be used for compacting cohesive, mixed, and granular

soils in confined areas.

This machine has been designed and built strictly for the intended use described

above. Using the machine for any other purpose could permanently damage the

machine or seriously injure the operator or other persons in the area. Machine

damage caused by misuse is not covered under warranty.

The following are some examples of misuse:

■ Using the machine as a ladder, support, or work surface

■ Using the machine to carry or transport passengers or equipment

■ Using the machine as a hammer or for other demolition work

■ Attaching the machine to any other machine

■ Operating the machine outside of factory specifications

■ Operating the machine in a manner inconsistent with all warnings found on the

machine and in the Operator’s Manual

This machine has been designed and built in accordance with the latest global

safety standards. It has been carefully engineered to eliminate hazards as far as

practicable and to increase operator safety through protective guards and labeling.

However, some risks may remain even after protective measures have been taken.

They are called residual risks. On this machine, they may include exposure to:

■ Heat, noise, exhaust, and carbon monoxide from the engine

■ Fire hazards from improper refueling techniques

■ Fuel and its fumes

■ Personal injury from improper lifting techniques or operating techniques

To protect yourself and others, make sure you thoroughly read and understand the

safety information presented in this manual before operating the machine.

wc_si000836gb_FM10.fm

19

Rammer

Safety Information

1.3 Safety Guidelines for Operating the Machine

Operator

training

Before operating the machine:

■ Read and understand the operating instructions contained in all manuals

delivered with the machine.

■ Familiarize yourself with the location and proper use of all controls and safety

devices.

■ Contact Wacker Neuson for additional training if necessary.

When operating this machine:

■ Do not allow improperly trained people to operate the machine. People

operating the machine must be familiar with the potential risks and hazards

associated with it.

Operator

qualifications

Only trained personnel are permitted to start, operate, and shut down the machine.

They also must meet the following qualifications:

■ have received instruction on how to properly use the machine

■ are familiar with required safety devices

The machine must not be accessed or operated by:

■ children

■ people impaired by alcohol or drugs

Application

area

Be aware of the application area.

■ Keep unauthorized personnel, children, and pets away from the machine.

■ Remain aware of changing positions and the movement of other equipment and

personnel in the application area/job site.

■ Identify whether special hazards exist in the application area, such as toxic

gases or unstable ground conditions, and take appropriate action to eliminate

the special hazards before using the machine.

Be aware of the application area.

■ Do not operate the machine in areas that contain flammable objects, fuels, or

products that produce flammable vapors.

Safety

devices,

controls, and

attachments

Only operate the machine when:

■ All safety devices and guards are in place and in working order.

■ All controls operate correctly.

■ The machine is set up correctly according to the instructions in the Operator’s

Manual.

■ The machine is clean.

■ The machine’s labels are legible.

To ensure safe operation of the machine:

■ Do not operate the machine if any safety devices or guards are missing or

inoperative.

■ Do not modify or defeat the safety devices.

■ Only use accessories or attachments that are approved by Wacker Neuson.

wc_si000836gb_FM10.fm

20

Rammer

Safety Information

Safe

operating

practices

When operating this rammer:

■ Remain aware of the rammer’s moving parts. Keep hands, feet, and loose

clothing away from the rammer’s moving parts.

■ When working near the edges of pits, slopes, trenches, and platforms, always

operate the rammer in such a way that there is no possibility of it tipping over or

falling in.

When operating this rammer:

■ Do not operate a rammer in need of repair.

■ Do not tamper with or disable the function of the operating controls.

■ Do not leave the rammer running unattended.

■ Do not consume the operating fluids used in this machine. Depending on your

machine model, these operating fluids may include water, wetting agents, fuel

(gasoline, diesel, kerosene, propane, or natural gas), oil, coolant, hydraulic fluid,

heat transfer fluid (propylene glycol with additives), battery acid, or grease.

Personal

Protective

Equipment

(PPE)

Wear the following Personal Protective Equipment (PPE) while operating this

machine:

■ Close-fitting work clothes that do not hinder movement

■ Safety glasses with side shields

■ Hearing protection

■ Safety-toed footwear

After Use

■ Stop the engine when the machine is not being operated.

■ Close the fuel valve on engines equipped with one when the machine is not

being operated.

■ Ensure that the machine will not tip over, roll, slide, or fall when not being

operated.

■ Store the machine properly when it is not being used. The machine should be

stored in a clean, dry location out of the reach of children.

1.4 Safety Guidelines for Lifting the Machine

When lifting the machine:

■ Make sure slings, chains, hooks, ramps, jacks, forklifts, cranes, hoists, and any

other type of lifting device used is attached securely and has enough weight-

bearing capacity to lift or hold the machine safely. See chapter Technical Data

for machine weight.

■ Remain aware of the location of other people when lifting the machine.

■ Only use the lifting points and tie-downs described in the Operator’s Manual.

■ Make sure the transporting vehicle has sufficient load capacity and platform size

to safely transport the machine.

To reduce the possibility of injury:

■ Do not stand under the machine while it is being lifted or moved.

■ Do not get onto the machine while it is being lifted or moved.

La page charge ...

Wacker Neuson BS60-4As Manuel utilisateur

Ce manuel convient également à

Wacker Neuson BS60-4As Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents