Wacker Neuson PG2A Manuel utilisateur

Taper
Manuel utilisateur
Operator’s Manual
Notice d'emploi
Pump
Pompe
PG2A
Type PG2A
Document 5000184868
Date
1117
Version
11
Language EN-FR
5000184868
Copyright notice
© Copyright 2017 by Wacker Neuson Production Americas LLC
All rights, including copying and distribution rights, are reserved.
This publication may be photocopied by the original purchaser of the
machine. Any other type of reproduction is prohibited without express
written permission from Wacker Neuson Production Americas LLC.
Any type of reproduction or distribution not authorized by Wacker
Neuson Production Americas LLC represents an infringement of valid
copyrights. Violators will be prosecuted.
Trademarks
All trademarks referenced in this manual are the property of their
respective owners.
Manufacturer
Wacker Neuson Production Americas LLC
N92W15000 Anthony Avenue
Menomonee Falls, WI 53051 U.S.A.
Tel: (262) 255-0500 · Fax: (262) 255-0550 · Tel: (800) 770-0957
www.wackerneuson.com
Original instructions
This Operators Manual presents the original instructions. The original
language of this Operator’s Manual is American English.
PG 2A Foreword
wc_tx001378gb.fm 3
Foreword
SAVE THESE INSTRUCTIONS—This manual contains important instructions for
the machine models below. These instructions have been written expressly by
Wacker Neuson Production Americas LLC and must be followed during installation,
operation, and maintenance of the machines.
Machine
documentation
From this point forward in this documentation, Wacker Neuson Production
Americas L
LC will be referred to as Wacker Neuson.
Keep a copy of the Operator’s Manual with the machine at all times.
Use the separate Parts Book supplied with the machine to order replacement
pa
rts.
Refer to the separate Repair Manual for detailed instructions on servicing and
repairing the machine.
If you are missing any of these documents, please contact Wacker Neuson to
o
rder a replacement or visit www.wacke
rneuson.com.
When ordering parts or requesting service information, be prepared to provide
th
e machine model number, item number, revision number, and serial number.
Expectations
for
information in
this manual
This manual provides information and procedures to safely operate and
maintain the above Wacker Neuson model(s). For your own safety and to
re
duce the risk of injury, carefully read, understand, and observe all inst
ructions
d
escribed in this manua
l.
Wacker Neuson expressly reserves the right to make technical modifications,
even without notice, which improve the performance or safety standards of its
mach
ines.
The information contained in this manual is based on machines manufactured
u
p until the time of publication. Wacker Neuson reserves the right to chang
e
a
ny portion of this information without notice.
CALIFORNIA
Proposition
65 Warning
Engine exhaust, some of its constituents, and certain vehicle components, contain
or emit chemicals known to the State of California to cause cancer and birth
defects or other reproductive harm.
Laws
pertaining to
spark
arresters
NOTICE: State Health Safety Codes and Public Resources Codes specify that in
certain locations spark arresters be used on internal combustion engines that use
hydrocarbon fuels. A spark arrester is a device designed to prevent accidental dis-
charge of sparks or flames from the engine exhaust. Spark arresters are qualified
and rated by the United States Forest Service for this purpose. In order to comply
with local laws regarding spark arresters, consult the engine distributor or the local
Health and Safety Administrator.
Manufacturer’s
approval
This manual contains references to approved parts, attachments, and modifica-
tions. The following definitions apply:
Machine Item Number
PG 2A 0007658, 0009054
Foreword PG 2A
4 wc_tx001378gb.fm
Approved parts or attachments are those either manufactured or provided by
W
acker Neuso
n.
Approved modifications are those performed by an authorized Wacker
Neuson service center according to written instructions published by Wacker
Neu
son.
Unapproved parts, attachments, and modifications are those that do not
meet
the approved criteria.
Unapproved parts, attachments, or modifications may have the following conse-
quences:
Serious injury hazards to the operator and persons in the work area
Permanent damage to the machine which will not be covered under warranty
Contact your Wacker Neuson dealer immediately if you have questions abo
ut
approved or
unapproved parts, attachments, or modifications.
2017_CE_PG2_PG2A_en.fm
EC Declaration of Conformity
Manufacturer
Wacker Neuson Production Americas LLC, N92W15000 Anthony Avenue,
Menomonee Falls, Wisconsin USA
Product
Product
Product category
Product function
Item number
Net installed power
Measured sound power level
Guaranteed sound power level
PG2A
Water Pump Units
To pump fluid
5000009054
2.6 kW
100 dB(A)
103 dB(A)
Conformity Assessment Procedure
According to ANNEX V
Notified Body
Lloyds Register Verification Limited (Notified Body No 0038)
71 Fenchurch Street, London EC3M 4BS, United Kingdom
Directives and Standards
We hereby declare that this product meets and complies with the relevant regulations and
requirements of the following directives and standards:
2000/14/EC, 2006/42/EC, 2014/30/EU
Authorized Person for Technical Documents
Robert Raethsel, Wacker Neuson Produktion GmbH & Co. KG, Wackerstrasse 6,
85084 Reichertshofen, Germany
Menomonee Falls, WI, USA, 25.08.17
Travis Pound
Manager, Product Engineering
For Wacker Neuson
Keith Herr
Vice President and Managing Director
For Wacker Neuson
Original Declaration of Conformity
Jeff Volden
Director, Product Engineering
For Wacker Neuson
PG 2A Table of Contents
wc_bo5000184844_11TOC.fm 7
Foreword 3
EC Declaration of Conformity 5
1 Safety Information 9
1.1 Signal Words Used in this Manual ....................................................... 9
1.2 Machine Description and Intended Use ............................................. 10
1.3 Safety Guidelines for Operating the Machine ..................................... 12
1.4 Operator Safety while Using Internal Combustion Engines ............... 14
1.5 Service Safety .................................................................................... 16
2 Labels 18
2.1 Label Locations .................................................................................. 18
2.2 Label Meanings .................................................................................. 19
3 Lifting and Transporting 21
4 Operation 22
4.1 Preparing the Machine for First Use ................................................... 22
4.2 Recommended Fuel ........................................................................... 23
4.3 Before Starting ................................................................................... 24
4.4 Starting ............................................................................................... 25
4.5 Stopping ............................................................................................. 25
4.6 Operation ............................................................................................ 26
4.7 Hoses and Clamps ............................................................................. 26
4.8 Emergency Shutdown Procedure ....................................................... 27
5 Maintenance 28
5.1 Maintaining the Emission Control System .......................................... 28
5.2 Periodic Maintenance Schedule ......................................................... 28
5.3 Cleaning the Pump ............................................................................. 29
5.4 Adjusting the Impeller Clearance ....................................................... 30
5.5 Replacing the Mechanical Seal .......................................................... 31
5.6 Spark Plug .......................................................................................... 32
5.7 Servicing the Air Cleaner .................................................................... 33
5.8 Engine Oil ........................................................................................... 34
5.9 Cleaning the Sediment Cup ............................................................... 35
5.10 Carburetor Adjustment ....................................................................... 36
Table of Contents PG 2A
8 wc_bo5000184844_11TOC.fm
5.11 Adjusting the Idle Speed .....................................................................36
5.12 Long-Term Storage .............................................................................37
6 Troubleshooting 38
7 Technical Data 39
7.1 Engine .................................................................................................39
7.2 Machine ...............................................................................................40
7.3 Sound Measurements .........................................................................40
7.4 Dimensions ..........................................................................................41
8 Emission Control Systems Information and Warranty 43
8.1 Emission Control Systems Warranty Statement .................................43
9 AEM Safety Manual 45
PG 2A Safety Information
wc_si000415gb.fm 9
1 Safety Information
1.1 Signal Words Used in this Manual
This manual contains DANGER, WARNING, CAUTION, NOTICE, and
NOTE signal words which must be followed to reduce the possibility
of personal injury, damage to the equipment, or improper service.
NOTICE: Used without the safety alert symbol, NOTICE indicates a
situation which, if not avoided, could result in property damage.
Note: A Note contains additional information important to a procedure.
This is the safety alert symbol. It is used to alert you to potential personal hazards.
f Obey all safety messages that follow this symbol.
DANGER
DANGER indicates a hazardous situation which, if not avoided, will result in death
or serious injury.
f To avoid death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
WARNING
WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
f To avoid possible death or serious injury from this type of hazard, obey all safety
messages that follow this signal word.
CAUTION
CAUTION indicates a hazardous situation which, if not avoided, could result in
minor or moderate injury.
f To avoid possible minor or moderate injury from this type of hazard, obey all
safety messages that follow this signal word.
Safety Information PG 2A
10 wc_si000415gb.fm
1.2 Machine Description and Intended Use
This machine is a centrifugal dewatering pump. The Wacker Neuson
Dewatering Pump consists of a tubular steel frame surrounding a
gasoline engine, a fuel tank, and an impeller pump with ports for water
suction and discharge. The engine rotates the impeller during
operation. Waste water is drawn into the pump through the suction
port and expelled through the discharge port. The operator connects
hoses to the pump and routes them so that water and solids are
drained from the work area and discharged into an appropriate
location.
This machine is intended to be used for general de-watering
applications. This machine is intended for the pumping of clear water,
or water containing solids up to the size stated within the product
specifications, and up to the flow, head and suction lift limits also
stated within the product specifications.
This machine has been designed and built strictly for the intended use
described above. Using the machine for any other purpose could
permanently damage the machine or seriously injure the operator or
other persons in the area. Machine damage caused by misuse is not
covered under warranty.
The following are some examples of misuse:
Pumping flammable, explosive, or corrosive fluids
Pumping hot or volatile fluids that result in pump cavitation
Operating the pump outside of product specifications due to
incorrect diameter hoses, incorrect length hoses, other inlet or
outlet restrictions, or excessive suction lift or head
Using the machine as a ladder, support, or work surface
Using the machine to carry or transport passengers or equipment
Operating the machine outside of factory specifications
Operating the machine in a manner inconsistent with all warnings
found on the machine and in the Operator’s Manual.
This machine has been designed and built in accordance with the
latest global safety standards. It has been carefully engineered to
eliminate hazards as far as practicable and to increase operator
safety through protective guards and labeling. However, some risks
may remain even after protective measures have been taken. They
are called residual risks. On this machine, they may include exposure
to:
Heat, noise, exhaust, and carbon monoxide from the engine
Fire hazards from improper refueling techniques
PG 2A Safety Information
wc_si000415gb.fm 11
Fuel and its fumes
Personal injury from improper lifting techniques
Projectile hazard from discharge
Crushing hazards from a tipping or falling pump
To protect yourself and others, make sure you thoroughly read and
understand the safety information presented in this manual before
operating the machine.
Safety Information PG 2A
12 wc_si000415gb.fm
1.3 Safety Guidelines for Operating the Machine
Familiarity and proper training are required for the safe operation of the
machine. Machines operated improperly or by untrained personnel
can be hazardous. Read the operating instructions contained in this
manual and the engine manual, and familiarize yourself with the
location and proper use of all controls. Inexperienced operators should
receive instruction from someone familiar with the machine before
being allowed to operate it.
Operator qualifications
Only trained personnel are permitted to start, operate, and shut down
the machine. They also must meet the following qualifications:
have received instruction on how to properly use the machine
are familiar with required safety devices
The machine must not be accessed or operated by:
children
people impaired by alcohol or drugs
Personal Protective Equipment (PPE)
Wear the following Personal Protective Equipment (PPE) while
operating this machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
1.3.1 Do not touch the engine or muffler while the engine is on or
immediately after it has been turned off. These areas get hot and may
cause burns.
1.3.2 Do not use accessories or attachments that are not recommended by
Wacker Neuson. Damage to equipment and injury to the user may
result.
1.3.3 Do not pump volatile, flammable, or low flash point fluids. These fluids
could ignite or explode.
1.3.4 Do not pump corrosive chemicals or water containing toxic
substances. These fluids could create serious health and
environmental hazards. Contact local authorities for assistance.
1.3.5 Do not open the priming plug when the pump is hot. Do not loosen or
remove inlet or discharge hose fittings when the pump is hot. Hot water
inside could be pressurized much like the radiator on an automobile.
Allow the pump to cool to the touch before loosening the plug and
before loosening or removing the inlet or discharge hose fittings.
WARNING
PG 2A Safety Information
wc_si000415gb.fm 13
1.3.6 Do not open pump housing cover while pump is operating, or start
pump with the cover off. The rotating impeller inside the pump can cut
or sever objects caught in it.
1.3.7 Do not block or restrict flow from inlet line or discharge line. Remove
kinks from discharge line before starting pump. Operation with a
blocked inlet line or discharge line can cause water inside pump to
overheat.
1.3.8 Read, understand, and follow procedures in the Operator’s Manual
before attempting to operate the machine.
1.3.9 Be sure operator is familiar with proper safety precautions and
operation techniques before using machine.
1.3.10 Be sure the machine is on a firm, level surface and will not tip, roll,
slide, or fall while operating.
1.3.11 Close fuel valve on engines equipped with one when machine is not
being operated.
1.3.12 Store the machine properly when it is not being used. The machine
should be stored in a clean, dry location out of the reach of children.
Safety Information PG 2A
14 wc_si000415gb.fm
1.4 Operator Safety while Using Internal Combustion Engines
Operating safety
When operating the pump:
Keep the area around exhaust pipe free of flammable materials.
Check the fuel lines and the fuel tank for leaks and cracks before
starting the engine.
When operating the pump:
Do not smoke while operating the machine.
Do not run the machine if fuel leaks are present or the fuel lines
are loose.
Do not run the engine near sparks or open flames.
Do not touch the engine or muffler while the engine is running or
immediately after it has been turned off.
Do not operate a machine when its fuel cap is loose or missing.
Do not start the engine if fuel has spilled or a fuel odor is present.
Move the machine away from the spill and wipe the machine dry
before starting.
Refueling safety
When refueling the engine:
Clean up any spilled fuel immediately.
Refill the fuel tank in a well-ventilated area.
Replace the fuel tank cap after refueling.
WARNING
Internal combustion engines present special hazards during operation and fueling.
Failure to follow the warnings and safety standards could result in severe injury or
death.
f Read and follow the warning instructions in the engine owner’s manual and the
safety guidelines below.
DANGER
Asphyxiation hazard. Using a pump indoors CAN KILL YOU IN MINUTES. Pump
exhaust contains carbon monoxide. This is a poison you cannot see or smell.
f NEVER use this pump inside a home or garage, EVEN IF doors and windows
are open. Only use OUTSIDE and far away from windows, doors, and vents.
f NEVER use a pump inside an enclosed area, such as a tunnel or a trench,
unless adequate ventilation is provided through such items as exhaust fans or
hoses.
PG 2A Safety Information
wc_si000415gb.fm 15
When refueling the engine:
Do not smoke.
Do not refuel a hot or running engine.
Do not refuel the engine near sparks or open flames.
Do not refuel if the machine is positioned in a truck fitted with a
plastic bed liner. Static electricity can ignite the fuel or fuel
vapors.
Safety Information PG 2A
16 wc_si000415gb.fm
1.5 Service Safety
A poorly maintained machine can become a safety hazard! In order
for the machine to operate safely and properly over a long period of
time, periodic maintenance and occasional repairs are necessary.
Personal Protective Equipment (PPE)
Wear the following Personal Protective Equipment (PPE) while
servicing or maintaining this machine:
Close-fitting work clothes that do not hinder movement
Safety glasses with side shields
Hearing protection
Safety-toed footwear
In addition, before servicing or maintaining the machine:
Tie back long hair.
Remove all jewelry (including rings).
1.5.1 Do not attempt to clean or service the machine while it is running.
Rotating parts can cause severe injury.
1.5.2 Do not crank a flooded engine with the spark plug removed on
gasoline-powered engines. Fuel trapped in the cylinder will squirt out
the spark plug opening.
1.5.3 Do not test for spark on gasoline-powered engines if the engine is
flooded or the smell of gasoline is present. A stray spark could ignite
the fumes.
1.5.4 Do not use gasoline or other types of fuels or flammable solvents to
clean parts, especially in enclosed areas. Fumes from fuels and
solvents can become explosive.
1.5.5 Keep the area around the muffler free of debris such as leaves, paper,
cartons, etc. A hot muffler could ignite the debris and start a fire.
1.5.6 Replace worn or damaged components with spare parts designed and
approved by Wacker Neuson.
1.5.7 When replacement parts are required for this machine, use only
Wacker Neuson replacement parts or those parts equivalent to the
original in all types of specifications, such as physical dimensions,
type, strength, and material.
1.5.8 Disconnect the spark plug on machines equipped with gasoline
engines, before servicing, to avoid accidental start-up.
WARNING
PG 2A Safety Information
wc_si000415gb.fm 17
Notes
Labels PG 2A
18 wc_si000416gb.fm
2 Labels
2.1 Label Locations
wc_gr000833
A
C
D
E
G, H
F
B
PG 2A Labels
wc_si000416gb.fm 19
1.2 Label Meanings
A
DANGER
Asphyxiation hazard.
Engines emit carbon monoxide.
Do not run the machine indoors or in an enclosed
area.
NEVER use inside a home or garage, EVEN IF doors
and windows are open.
Only use OUTSIDE and far away from windows, doors,
and vents.
Read the Operator’s Manual.
No sparks, flames, or burning objects near the
machine.
Stop the engine before refueling.
B
WARNING
Hot surface
C
CAUTION
Read and understand the supplied Operator’s Manual
before operating this machine. Failure to do so
increases the risk of injury to yourself and others.
D
WARNING
Pressurized contents. Do not open when hot!
E
Impeller rotation.
STOP
STOP
178715
178715
wc_gr014566
wc_gr014563
wc_gr014565
wc_gr014564
Labels PG 2A
20 wc_si000416gb.fm
F
Guaranteed sound power level in db(A)
G
A nameplate listing the model number, item number,
revision number, and serial number is attached to each
unit. Please record the information found on this name-
plate so it will be available should the nameplate
become lost or damaged. When ordering parts or
requesting service information, you will always be asked
to specify the model number, item number, revision
number, and serial number of the unit.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104

Wacker Neuson PG2A Manuel utilisateur

Taper
Manuel utilisateur

dans d''autres langues