Simplicity 071020-0 Manuel utilisateur

Marque: Simplicity

Modèle: 071020-0

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

Generator Systems

Installation & Operator’s Manual

100/200 Amp Automatic

Transfer Switch

with ACPower Control Module™

NOT

FOR

REPRODUCTION

2 BRIGGSandSTRATTON.COM

Thank you for your purchase of this Briggs & Stratton® Power Products automatic transfer switch. This product is designed

for use with specific home standby generators and may not function with generators produced by other manufacturers.

Seek a qualified electrical professional to determine applicability of this equipment to generators manufactured by others.

When operated and maintained according to the instructions in this manual, your system will provide many years of

dependableservice.

This manual contains safety information to make you aware of the hazards and risks associated with this system and how to

avoid them. We have made every effort to provide for a safe, streamlined and cost-effective installation. As each installation

is unique, it is impossible to know of and advise of all conceivable procedures and methods by which installation might be

achieved. We do not know all possible hazards and/or the results of each possible method or procedure. It is important that

you read and understand these instructions thoroughly before attempting to install or operate this equipment. Save these

instructions for future reference.

This transfer switch requires professional installation before use. Refer to the Installation section of this manual for

instructions on installation procedures. Only licensed electrical contractors should install transfer switches. Installations must

strictly comply with all applicable federal, state and local codes, standards and regulations. Your installer should follow the

instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your system. Consult your Yellow Pages.

There are many authorized service dealers who provide quality service. You can also contact Technical Service by phone at

(800) 743 4115 between 8:00 AM and 5:00 PM CT, or on the Internet at BRIGGSandSTRATTON.COM.

For Future Reference

Please fill out the information below and keep with your receipt to assist in unit identification for future purchase issues.

Transfer Switch

Model Number

Revision

Serial Number

Date Purchased

Briggs & Stratton Power Products Group, LLC

P.O. Box 702

Milwaukee, WI 53201-0702

may be reproduced or transmitted in any form without the express

written permission of Briggs & Stratton Power Products Group, LLC.

NOT

FOR

REPRODUCTION

Table of Contents

Important Safety Instructions........................4

Installation ....................................5

Owner Orientation ............................................5

Installing Dealer/Contractor Responsibilities ........................5

Mounting Guidelines ..........................................6

Power Wiring Interconnections ..................................7

Supervisory Control Wiring .....................................8

System Setup...............................................11

System Test ................................................11

Controls ..................................... 11

Operation .................................... 11

Testing the Automatic Transfer Switch ...........................12

Maintenance .................................. 12

Troubleshooting................................ 13

Schematic and Wiring Diagram, Models 071018 and 071019..........14

Schematic and Wiring Diagram, Models 071020 and 071021..........15

Warranty..................................... 16

Product Specifications ........................... 17

NOT

FOR

REPRODUCTION

4 BRIGGSandSTRATTON.COM

Important Safety Instructions

SAVE THESE INSTRUCTIONS - This manual contains

important instructions that should be followed during

installation and maintenance of the equipment.

Safety Symbols and Meanings

The safety alert symbol indicates a potential personal

injury hazard. A signal word (DANGER, WARNING, or

CAUTION) is used with the alert symbol to designate a

degree or level of hazard seriousness. A safety symbol

may be used to represent the type of hazard. The signal

word NOTICE is used to address practices not related to

personal injury.

DANGER indicates a hazard which, if not avoided, will

result in death or serious injury.

WARNING indicates a hazard which, if not avoided, could

result in death or serious injury.

CAUTION indicates a hazard which, if not avoided, could

result in minor or moderate injury.

NOTICE addresses practices not related to personal injury.

The manufacturer cannot possibly anticipate every possible

circumstance that might involve a hazard. The warnings in

this manual, and the tags and decals affixed to the unit are,

therefore, not all-inclusive. If you use a procedure, work

method or operating technique that the manufacturer does

not specifically recommend, you must satisfy yourself that

it is safe for you and others. You must also make sure that

the procedure, work method or operating technique that you

choose does not render the equipment unsafe.

Electrical Shock Read Manual

WARNING Only qualified electricians should attempt

installation of this equipment, which must strictly comply

with applicable codes, standards and regulations.

WARNING Certain components in this product and

related accessories contain chemicals known to the State

of California to cause cancer, birth defects, or other

reproductive harm. Wash hands after handling.

WARNING Low voltage wire cannot be installed in

same conduit as power voltage wiring.

• Failure to follow above warning could cause personal

injury, damage and/or malfunction of equipment.

WARNING Failure to properly ground equipment can

result in electrocution.

• Do not touch bare wires.

• Do not use equipment with worn, frayed, bare or

otherwise damaged wiring.

• Do not handle electrical cords while standing in water,

while barefoot, or while hands or feet are wet.

• If you must work around a unit while it is operating, stand

on an insulated dry surface to reduce shock hazard.

• Do not allow unqualified persons or children to operate or

service equipment.

• In case of an accident caused by electrical shock,

immediately shut down all sources of electrical power

and contact local authorities. Avoid direct contact with

the victim.

WARNING Equipment contains high voltage that can

cause personal injury or death.

• Despite the safe design of the system, operating this

equipment imprudently, neglecting its maintenance or

being careless can cause possible injury or death.

NOTICE Improper treatment of equipment can damage it

and shorten its life.

• Use equipment only for intended uses.

• If you have questions about intended use, ask dealer or

contact Briggs & Stratton Power Products.

• Do not expose equipment to excessive moisture, dust,

dirt, or corrosive vapors.

• Remain alert at all times while working on this equipment.

Never work on the equipment when you are physically or

mentally fatigued.

• If connected devices overheat, turn them off and turn off

their circuit breaker/fuse.

SAVE THESE INSTRUCTIONS

NOT

FOR

REPRODUCTION

Installation

We sincerely appreciate your patronage. For this reason,

we have made significant effort to provide for a safe,

streamlined and cost-effective installation. Because each

installation is unique, it is impossible to know of and advise

the trade of all conceivable procedures and methods by

which installation might be achieved. Neither could we know

of possible hazards and/or the results of each method or

procedure. For these reasons,

Only current licensed electrical should attempt system

installations. Installations must strictly comply with all

applicable codes, industry standards and regulations.

Your equipment is supplied with this combined “Installation

and Operator’s Manual”. This is an important document and

should be retained by the owner after the installation has

been completed.

Every effort has been made to make sure that the information

in this manual is both accurate and current. However, the

manufacturer reserves the right to change, alter or otherwise

improve the system at any time without prior notice.

Home Owner Responsibilities

To help you make informed choices and communicate

effectively with your installation contractor(s),

Read and understand Owner Orientation before contracting

or starting your equipment installation.

To arrange for proper installation, contact the store at which

you purchased your equipment, your dealer, or your utility

power provider.

The equipment warranty is VOID unless the system is

installed by licensed electrical professionals.

Owner Orientation

The illustrations provided are for typical circumstances and

are meant to familiarize you with the installation options

available with your system.

Local codes, appearance, and distances are the factors that

must be considered when negotiating with an installation

professional. As the distance from the existing electrical

service increases, compensation in wiring materials must

be allowed for. This is necessary to comply with local codes

and overcome electrical voltage drops.

These factors will have a direct effect on the overall price

of your equipment installation.

NOTE: Your installer must check local codes AND obtain

permits before installing the system.

 • Readandfollowtheinstructionsgiveninthismanual.

 • Followaregularscheduleincaringforandusingyour

equipment, as specified in this manual.

Installing Dealer/Contractor Responsibilities

 • Readandobservethesafetyrules.

 • Readandfollowtheinstructionsgiveninthismanual.

 • Theinstallermayneedtoprovideappropriaterated

contactors based on loads to be controlled.

 • Checkfederal,stateandlocalcodesandauthority

having jurisdiction, for questions on installation.

 • Ensuregeneratorisnotoverloadedwithselectedloads.

If you need more information about the transfer switch, call

(800) 743-4115, between 8:00 AM and 5:00 PM CT.

Equipment Description

The transfer switch is designed to transfer the selected

loads found in normal residential installations to generator

power in the event of a utility power failure. The load is

connected either to utility power (normal) or home standby

power (generator). The transfer switch monitors utility and

generator voltages and will automatically connect to the

appropriate source of power.

These switches make it easy for a licensed electrician to

complete a home standby installation. Depending on the

specific model purchased, service conduit and conductors

can be wired directly from the hour-meter to the transfer

switche a separate disconnect and associated wiring are not

required when installed per applicable federal, state and local

codes, standards and regulations.

Major components of the transfer switch are a 2 pole utility

disconnect circuit breaker, a 2 pole generator disconnect

circuit breaker, a 2 pole double throw transfer switch, control

circuit board, fused utility terminals and interconnecting

wiring. The control board also has two inputs for current

transformers that sense generator current. These

components are housed in a NEMA 3R enclosure that is

suitable for both indoor and outdoor installations.

The transfer switch is solenoid-operated from utility or

generator inputs and contain suitable mechanical and

electrical interlock switches to eliminate the possibility of

connecting the utility service to the generator output. It

has ratings capable of switching full utility power into the

residence. In addition, a manual override lever is provided

for the transfer function.

The control board has active circuits sensing utility and

generator voltages. It creates a signal for the generator

start-up, switch transfer and retransfer when utility is

restored. The control board also contains red and green

LED’s indicating the power sources available and two

relay operated contacts that provide supervisory control of

external loads.

NOT

FOR

REPRODUCTION

6 BRIGGSandSTRATTON.COM

Delivery Inspection

After opening the carton, carefully inspect the transfer

switch components for any damage that may have occurred

duringshipment.

IMPORTANT: If loss or damage is noted at time of delivery,

have the person(s) making delivery note all damage on the

freight bill and affix his signature under the consignor’s

memo of loss or damage. If loss or damage is noted after

delivery, contact the carrier for claim procedures. Missing or

damaged parts are not warranted.

Shipment contents

 • Automatictransferswitch(1)

 • Installationandoperator’smanual(1)

 • Currenttransformers(2)

To be supplied by installer:

 • Connectingwireandconduit

 • Variousspecialtytools/equipment

Mounting Guidelines

The system circuitry is enclosed in a NEMA Type 3R

enclosure suitable for indoor/outdoor use. Guidelines for

mounting the enclosure include:

 • Installenclosureonafirm,sturdysupportingstructure.

 • TheenclosuremustbeinstalledwithminimumNEMA

3R hardware for conduit connections.

 • Levelandplumbtheenclosure.Thiscanbedone

by placing washers between the enclosure and the

mounting surface.

 • NEVERinstalltheswitchwhereanycorrosive

substance might drip onto the enclosure.

 • Protecttheswitchatalltimesagainstexcessive

moisture, dust, dirt, lint, construction grit and corrosive

vapors.

Typical automatic transfer switch installations are depicted

below. It is best if the transfer switch is mounted near

the utility meter, either inside or outside. Discuss layout

suggestions/ changes with the owner before beginning the

system installation process.

Main

Distribution

Panel

Transfer

Switch

Hot Water

Heater

Air

Conditioner

Contactor

Disconnect Switch

Generator

Watt -

Hourmeter

Branch

Circuits

Emergency Branch

Circuits

— — — — — — Control Wiring

Emergency

Load

Center

071018 &071019

071020 & 071022

Main

Distribution

Panel

Transfer Switch

w/ Service

and Generator

Disconnect

Hot Water

Heater

Air

Conditioner

Generator

Watt -

Hourmeter

— — — — — — Control Wiring

Disconnect Switch

Contactor

Branch Circuits

NOT

FOR

REPRODUCTION

Power Wiring Interconnections

All wiring must be the proper size, properly supported

and protected by conduit. All wiring should be done per

applicable federal, state and local codes, standards and

regulations. Obey wire type and torque specifications printed

on the terminal blocks and neutral/ground connector.

Complete the following connections between the transfer

switch, main distribution panel, utility power and generator.

Useunstaller-supplied300VACorgreaterwirethatcomplies

with Table 310.16 in the National Electric Code. Apply the

necessary correction factors and wire size calculations.

1. Set generator’s system switch to OFF position.

2. Set generator’s circuit breaker to OFF (open) position.

3. Turn off utility power to the standby generator and

transfer switch.

4. Connect transfer switch to utility power:

To connect models 071018 and 071019 to utility:

 • Connectcopperfeederconductorsfrommain

distribution panel two-pole breaker to transfer switch

terminals marked “UTILITY CONNECTION”.

 • Connectcopperconductorfrommaindistributionpanel

neutral bus to transfer switch neutral terminal.

 • Connectcopperconductorfrommaindistributionpanel

ground bus to transfer switch “GND” terminal.

NOTE: Assure grounding electrode conductor is

connected and bonded per applicable federal, state and

local codes, standards and regulations.

To connect models 071020 and 071021 to utility:

 • Connectutilityservicetotransferswitchservice

disconnect circuit breaker terminals marked

“UTILITYCONNECTION”.

 • Connectutilityserviceneutraltotransferswitch

neutralterminal.

5. Connect copper feeder conductors from transfer

switch breaker “GENERATOR CONNECTION” terminals

to generator control panel breaker LINE1 and LINE2

terminals. Each conductor must pass through hole of

current transformer before makingconnection.

6. Plug current transformer leads into “CT1” and “CT2”

terminals on control module.

7. Connect copper conductor from transfer switch

neutral terminal to generator control panel NEUTRAL

terminal. Observe control panel labeling for

terminalidentification.

8. Connect copper conductor from transfer switch “GND”

terminal to generator control panel GROUND terminal.

NOTE: Assure generator equipment grounding conductor

is connected per applicable federal, state and local codes,

standards and regulations.

WARNING Low voltage wire cannot be installed in

same conduit as power voltage wiring.

• Failure to follow above warning could cause personal

injury, damage and/or malfunction of equipment.

NOTICE Improper installation can cause damage to the

circuit boards and shorten their life. Installing circuit

boards in live circuits will damage the board and is not

covered by warranty. ALWAYS disconnect ALL sources of

power prior to servicing.

• Remove all power prior to installing this equipment.

Failure to do so could cause internal damage to the board

when making electrical connections.

• Turn generator to OFF position.

• Turn off utility power to the standby generator and

transfer switch.

WARNING Battery posts, terminals and related

accessories contain lead and lead compounds, chemicals

known to the State of California to cause cancer and

reproductive harm. Wash hands after handling.

240V

120V

Neutral

Ground

To Transfer Switch

Line 1 Neutral

Ground

Line 2

Circuit

Breaker

NOT

FOR

REPRODUCTION

8 BRIGGSandSTRATTON.COM

 9. Connectthetransferswitch“UTILITY240VAC”

terminalstogenerator’s“240VAC”terminals

usinginstallersupplied300VACorgreatercopper

wire, minimum #14 AWG conductors via supplied

two-poleconnector.

10. Connect “T/R” and “GND” terminals on transfer

switch control board (B) to the generator’s control

panel (A) “TxRx” and “TxRx GND” terminals using

#18 AWG twisted pair copper conductors, no greater

than 200 ft in length, 300 volt 75°C-90°C via supplied

ten-poleconnector.

11. Tighten all wire connections/fasteners to proper torque.

See label inside transfer switch enclosure for proper

torque values.

  • Whenconnectingtocircuitboardterminalblocks,

fasten only one wire to each connector screw.

Connector tightening torques shall be asfollows:

Utility - 50 in-lb (5.5 Nm) Ground - 50 in-lb (5.5 Nm)

Generator - 50 in-lb (5.5 Nm)

Control - 12 in-lb (1.4 Nm)

Neutral - 110 in-lb (12.5Nm)

Fuseblocks - 12 in-lb (1.4Nm)

Use oxide inhibitor on all aluminum terminations.

All terminal and bus lugs are suitable for copper wire of

60°/75°C rating.

The illustrations on the following pages show typical

completed installations. Your actual installation will vary.

Supervisory Control Wiring

An air conditioner can be used with the supervisory contacts

on either terminals A-A or B-B. Terminals A-A can only be

used with supervisory control. Large loads can only be used

with contactor control on terminals B-B. Examples of each

system are described below.

1. The terminal strip on the control module in transfer

switch has four connections for customer use. There

are two sets of “Normally Closed” contacts available.

They will be activated when generator power is

required. These can be used for supervisory control

of large connected loads on generator. Loads will

be allowed to operate if there is enough generator

poweravailable.

NOTE: There are two wireways provided to keep the

supervisory loads separated from each other.

2. Terminals “A-A” on control module are rated for

24VACandairconditionercontactorcontrol.Contacts

are connected in series with the air conditioner

contactor control circuit.

3. Terminals “B-B” on control module are rated for 1 Amp

125VACandinstallersuppliedcontactortocontrol

a large load, such as an electric hot water heater.

Contacts are connected in series with the contactor

control circuit.

4. Tighten all wire connections/fasteners to proper torque.

See label inside transfer switch enclosure for proper

torque values.

Air Conditioner Contactor

24VAC

Contactor

Neutral

120VAC

NOT

FOR

REPRODUCTION

Essential Circuit

Sub Panel

Ground

Terminal

Load

Connection

Generator

Connection

Utility

Connection

Supervisory

Contacts

Neutral

Terminal

UTILITY 240VAC to Generator

T/R and GND

to Generator

XRX

TXRX Gnd

Two Pole

Breaker

Neutral

Bus

Ground

Bus

To Utility

Main

Distribution

Panel

Automatic

Transfer

Switch

B&S Generator

CT’s

240VAC

Neutral

Bus

Ground

Bus

240

VAC

Models 071018 & 071019

NOT

FOR

REPRODUCTION

10 BRIGGSandSTRATTON.COM

Ground

Terminal

Load

Connection

Generator

Connection

Utility

Connection

Supervisory

Contacts

Neutral

Terminal

UTILITY 240VAC

to Generator

T/R and Gnd

to Generator

XRX

TXRX Gnd

To Utility

Main

Distribution

Panel

Automatic

Transfer

Switch

B&S Generator

CT’s

240VAC

Neutral

Bus

Ground

Bus

240

VAC

Models 071020 & 071021

NOT

FOR

REPRODUCTION

System Setup

You must perform the following before operating the system:

 • Ifgeneratorisinstalledinanarearegularlysubjected

to temperatures below 40°F (4°C), select a 50 second

warm up time by moving jumper installed on JP2 from

‘20’ position to ‘50’ position.

 • Settwo-positionSW1onthecontrolmoduletomatch

the fuel supplied to the home standby generator, either

NG or LP.

 • Setthree-positionSW2onthecontrolmoduleto

match the KW rating of the home standby generator:

12,15or20.

System Test

With the generator system switch in AUTO, turn the service

disconnect feeding the transfer switch to the OFF position.

After a few minutes the generator will start and the transfer

switch will transfer to generator power.

To return to utility power, turn the service disconnect feeding

the transfer switch to the ON position.

Controls

Other than a Manual Override lever, there are no operator

controls because this is an automatic transfer switch. The

manual override is to be used only by licensed professionals.

Operation

To select automatic transfer operation, do the following:

1. Set service disconnect switch that sends utility power

to transfer switch contactor to “ON” position.

2. Install 15 Amp fuse in generator’s control panel.

3. Set generator’s circuit breaker to “ON” position.

4. Set generator’s system switch to “AUTO” position.

The system will now be in automatic operation mode.

When the generator is providing power to the transfer

switch, the control module is constantly monitoring

generator power. If the air conditioner is called to run, and

there is sufficient generator power available, the controller

will close contacts “A-A” to air conditioner contactor.

Contacts “B B” will open before contacts A-A close. If loads

are too great for the generator, contacts A-A and/or B-B will

open. When air conditioning is not needed, A-A will open. If

enough power is available, B-B will close.

Enclosure Door

To open door, press the spring-load door lock to the right

and pull down on the door.

To close and latch door, push door closed against enclosure.

While in this position, push door upwards. This will cause

spring-load door lock to engage and latch door in place.

NOTE: Enclosure door MUST be closed and latched at all

times except when system is being serviced.

2 Position

Switch SW1

3 Position

Switch SW2

JP2

CT1 & CT2

Connectors

Supervisory

Contacts

NOT

FOR

REPRODUCTION

12 BRIGGSandSTRATTON.COM

Testing the Automatic Transfer Switch

Turn the main distribution panel breaker or service

disconnect feeding the transfer switch contactor to the “Off”

position. The system’s automatic sequence will initiate.

To return to utility power, turn the main distribution panel

breaker or service disconnect to the “On” position.

Utility Fail

The generator senses when utility voltage is below

70percent of nominal. Engine start sequence is initiated

after 6second time delay.

Engine Warm-Up

Time delay to allow for engine warm-up before transfer. Use

jumper on control board to select delay of 20 seconds or

50seconds.

Transfer

Transfer from utility to generator supply occurs after voltage

is above set levels. Minimum engine run time is 5 minutes

after transfer.

Utility Pickup

Voltagepickuplevelis80percentofnominalvoltage.

Retransfer

Retransfer from generator to utility power is approximately

10 seconds after utility voltage supply is above pickup level

and minimum run time is completed.

Engine Cool Down

Engine will run for 60 seconds after retransfer.

Maintenance

The transfer switch is designed to be maintenance free under

normal usage. However, inspection and maintenance checks

should be made on a regular basis. Maintenance will consist

mainly of keeping the transfer switch clean.

Visualinspectionsshouldbedoneatleastonceamonth.

Access to transfer switch must not be obstructed. Keep

3feet (92 cm) clearance around transfer switch. Check

for an accumulation of dirt, moisture and/or corrosion

on and around the enclosure, loose parts/hardware,

cracks and/or discoloration to insulation, and damaged or

discoloredcomponents.

Exercise the transfer switch at least once every three months

as described in Testing the Automatic Transfer Switch unless

a power outage occurs and home generator system has gone

through an automatic sequence. Allow generator to run for at

least 30minutes.

Contact a licensed electrical professional to inspect and clean

the inside of the enclosure and other components of your

home generator system at least once a year.

When Calling for Assistance

You must have the Model Number and Serial Number from

the unit ID label at hand if it is necessary to contact a local

service center regarding service or repair of this unit. Obtain

this information from the unit ID label located on or inside

the enclosure.

To contact Briggs & Stratton call (800) 743 4115, between

8:00 AM and 5:00 PM CT.

Installation Inspection

Before placing the generator system into service, inspect the

entire installation carefully.

Complete the ”Installation Checklist” supplied with the

generator as you make the inspection. Ensure all items have

been filled-in and all signatures have been obtained. Instruct

the owner to mail the white copy to:

Warranty Registration

P. O. Box 239

Jefferson, WI 53549

NOT

FOR

REPRODUCTION

Troubleshooting

Problem Cause Correction

Automatic transfer switch does not

transfer to generator

1. Generator breaker open.

2. Generator voltage not acceptable.

1. Reset generator circuit breaker.

2. Refer to generator manual.

Automatic transfer switch does not

transfer to utility

1. Main distribution panel breaker open

(Models 071018 & 071019 only).

2. Service disconnect breaker open

(Models 071020 & 071021 only).

3. Utility voltage not acceptable.

1. Reset main distribution panel breaker

(Models 071018 & 071019 only).

2. Reset service disconnect breaker

(Models 071020 & 071021 only).

3. Wait for utility voltage to return

tonormal.

Generator is still running after switch

transfers to utility power

Engine cool down period. Engine should stop after 1 minute.

Supervised loads (air conditioner, etc.)

are not operating when generator is

supplying power

1. A-A or B-B contacts not

operatingcorrectly.

2. Too much load on generator.

3. Current transformer not connected.

4. Broken current transformer.

1. Check A-A or B-B contacts for proper

operation and/or check control wiring

to external load.

2. Decrease load to generator.

3. Plug CT connectors into

controlboard.

4. Contact local service center.

Generator is still running after utility

power is restored

1. Minimum engine run time has

notelapsed.

2. Fuse(s) in transfer switch is defective.

1. Wait five minutes for transfer switch

to retransfer to utility power.

2. Check fuse(s) and replace

ifnecessary

NOT

FOR

REPRODUCTION

14 BRIGGSandSTRATTON.COM

Schematic and Wiring Diagram, Models 071018 and 071019

NOT

FOR

REPRODUCTION

Schematic and Wiring Diagram, Models 071020 and 071021

NOT

FOR

REPRODUCTION

16 BRIGGSandSTRATTON.COM

ABOUT YOUR WARRANTY

We welcome warranty repair and apologize to you for being inconvenienced. Any Authorized Service Dealer may perform warranty repairs. Most warranty

repairs are handled routinely, but sometimes requests for warranty service may not be appropriate. For example, warranty service would not apply if

equipment damage occurred because of misuse, lack of routine maintenance, shipping, handling, warehousing or improper installation. Similarly, the

warranty is void if the manufacturing date or the serial number on the equipment has been removed or the equipment has been altered or modified. During

the warranty period, the Authorized Service Dealer, at its option, will repair or replace any part that, upon examination, is found to be defective under normal

use and service. This warranty will not cover the following repairs and equipment:

• Normal Wear: Outdoor Power Equipment, like all mechanical devices, needs periodic parts and service to perform well. This warranty does not cover

repair when normal use has exhausted the life of a part or the equipment.

• Installation and Maintenance: This warranty does not apply to equipment or parts that have been subjected to improper or unauthorized installation

or alteration and modification, misuse, negligence, accident, overloading, improper maintenance, repair or storage so as, in our judgment, to adversely

affect its performance and reliability. This warranty also does not cover normal maintenance such as adjustments, cleaning and fuse replacement.

• Other Exclusions: This warranty excludes wear items or damage or malfunctions resulting from accidents, abuse, modifications, alterations, or

improper servicing. Accessory parts are excluded from the product warranty. This warranty excludes failures due to acts of God and other force

majeure events beyond the manufacturers control. Also excluded is used, reconditioned, and demonstration equipment. 198180E, Rev. C, 12/31/2006

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

JEFFERSON, WI, USA

The warranty period begins on the date of purchase by the first retail consumer or commercial end user, and continues for the period of time stated in the

table above. “Consumer use” means personal residential household use by a retail consumer. “Commercial use” means all other uses, including use for

commercial, income producing or rental purposes. Once equipment has experienced commercial use, it shall thereafter be considered as commercial use for

purposes of this warranty. Equipment used for prime power in place of utility are not applicable to this warranty.

NOWARRANTYREGISTRATIONISNECESSARYTOOBTAINWARRANTYONBRIGGS&STRATTONPRODUCTS.SAVEYOURPROOFOFPURCHASE

RECEIPT.IFYOUDONOTPROVIDEPROOFOFTHEINITIALPURCHASEDATEATTHETIMEWARRANTYSERVICEISREQUESTED,THEMANUFACTURING

DATE OF THE PRODUCT WILL BE USED TO DETERMINE THE WARRANTY PERIOD.

3 years

None

Consumer Use

Commercial Use

WARRANTY PERIOD

Warranty

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC TRANSFER SWITCH OWNER WARRANTY POLICY

Effective November 1, 2005 replaces all undated Warranties and all Warranties dated before November 1, 2005

LIMITED WARRANTY

Briggs & Stratton Power Products Group, LLC will repair or replace, free of charge, any part(s) of the equipment that is defective in material or

workmanship or both. Transportation charges on product submitted for repair or replacement under this warranty must be borne by purchaser. This

warranty is effective for the time periods and subject to the conditions stated below. For warranty service, find the nearest Authorized Service Dealer in

our dealer locator map at BRIGGSandSTRATTON.COM.

THERE IS NO OTHER EXPRESS WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO ONE YEAR FROM PURCHASE, OR TO THE EXTENT PERMITTED BY LAW. ANY AND ALL IMPLIED WARRANTIES ARE

EXCLUDED.LIABILITYFORINCIDENTALORCONSEQUENTIALDAMAGESAREEXCLUDEDTOTHEEXTENTEXCLUSIONISPERMITTEDBYLAW.Some

states or countries do not allow limitations on how long an implied warranty lasts, and some states or countries do not allow the exclusion or limitation

of incidental or consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you

may also have other rights which vary from state to state or country to country.

NOT

FOR

REPRODUCTION

Product Specifications

Model 071018

Rated Maximum Load Current*

(at 25°C/77°F) ......................................................100 Amps

RatedACVoltage .................................................... 250Volts

Poles .................................................................................... 2

Frequency ..................................................................... 60 Hz

Fault Current Rating ....... 22,000 RMS Symmetrical Amperes

Supervisory Contacts Rating:

A-A Terminals.................................................... 24VoltAC

B-B Terminals.................... 1Amp,125VoltAC,PilotDuty

Normal Operating Range .... -20°F (-28.8°C) to 104°F (40°C)

Weight ............................................................25 lbs. (11 kg)

Model 071019

Rated Maximum Load Current*

(at 25°C/77°F) ......................................................200 Amps

RatedACVoltage .................................................... 250Volts

Poles .................................................................................... 2

Frequency ..................................................................... 60 Hz

Fault Current Rating ....... 25,000 RMS Symmetrical Amperes

Supervisory Contacts Rating:

A-A Terminals.................................................... 24VoltAC

B-B Terminals.................... 1Amp,125VoltAC,PilotDuty

Normal Operating Range .... -20°F (-28.8°C) to 104°F (40°C)

Weight ............................................................38 lbs. (17 kg)

Model 071020

Rated Maximum Load Current*

(at 25°C/77°F) ......................................................100 Amps

RatedACVoltage .................................................... 250Volts

Poles .................................................................................... 2

Frequency ..................................................................... 60 Hz

Fault Current Rating ....... 22,000 RMS Symmetrical Amperes

Supervisory Contacts Rating:

A-A Terminals.................................................... 24VoltAC

B-B Terminals.................... 1Amp,125VoltAC,PilotDuty

Normal Operating Range .... -20°F (-28.8°C) to 104°F (40°C)

Weight ............................................................40 lbs. (18 kg)

Model 071021

Rated Maximum Load Current*

(at 25°C/77°F) ......................................................200 Amps

RatedACVoltage .................................................... 250Volts

Poles .................................................................................... 2

Frequency ..................................................................... 60 Hz

Fault Current Rating ....... 25,000 RMS Symmetrical Amperes

Supervisory Contacts Rating:

A-A Terminals.................................................... 24VoltAC

B-B Terminals.................... 1Amp,125VoltAC,PilotDuty

Normal Operating Range .... -20°F (-28.8°C) to 104°F (40°C)

Weight ............................................................63 lbs. (29 kg)

Automatic Transfer Switch

Briggs & Stratton Power Products Group, LLC

900 N. Parkway

Jefferson, Wisconsin, 53549 U.S.A.

*This transfer switch is certified in accordance with UL (Underwriters Laboratories) 1008 (transfer switch equipment).

NOT

FOR

REPRODUCTION

18 BRIGGSandSTRATTON.COM

Reserved

NOT

FOR

REPRODUCTION

Generator Systems

Manual de Instalación y del Operario

100/200 Amperios

Interruptor de

transferencia automática

NOT

FOR

REPRODUCTION

2 BRIGGSandSTRATTON.COM

Gracias por comprar este conectador automático de Briggs & Stratton® Power Products. Este producto está diseñado para

utilizarse con generadores de reserva domésticos específicos y puede no funcionar con generadores producidos por otros

fabricantes. Recurra a un electricista profesional cualificado para determinar la aplicabilidad de este equipo en generadores

fabricados por terceros. Si se utiliza y mantiene de acuerdo con las instrucciones de este manual, su sistema le proporcionará

muchos años de funcionamiento fiable.

Este manual contiene información de seguridad para que usted conozca los peligros y riesgos propios de este sistema y

cómo evitarlos. Se ha realizado el máximo esfuerzo para que la instalación resulte segura, sencilla y económica. Debido a que

cada instalación es única, es imposible conocer y recomendar todos los procedimientos y métodos posibles para efectuarla.

No conocemos todos los riesgos y/o resultados posibles de cada método o procedimiento existente. Es importante que lea

y comprenda perfectamente estas instrucciones antes de intentar instalar o utilizar este equipo. Guarde estas instrucciones

para futuras consultas.

Este el conectador requiere instalación profesional antes de utilizarse. Consulte las instrucciones sobre los procedimientos

de instalación en la sección Instalación del presente manual. Los conectador sólo deben ser instalados por electricistas con

licencia. Las instalaciones deben cumplir estrictamente la totalidad de los códigos, estándares y regulaciones federales,

estatales y locales vigentes. El instalador debe seguir las instrucciones detalladamente.

Ubicación

Nunca debe ir demasiado lejos para encontrar el soporte y servicio de Briggs & Stratton para su sistema. Consulte las

Páginas Amarillas. Existen múltiples distribuidores de servicio autorizados que ofrecen un servicio de calidad. También puede

comunicarse con el Servicio técnico por teléfono al (800) 743 4115 de 8:00 a. m. a 5:00 p. m. Hora del Centro, o a través de

Internet en BRIGGSandSTRATTON.COM.

Para futuras consultas

Llene la siguiente información y conserve su factura para facilitar la identificación de la unidad en caso de que surjan

problemas relacionados con la compra en el futuro.

Conectador automático

Número de modelo

Revisión

Número de serie

Fecha de compra

Briggs & Stratton Power Products Group, LLC.

P.O. Box 702

Milwaukee, WI 53201-0702

reproducción o transmisión total o parcial de este material, sin el permiso

previo y por escrito de Briggs & Stratton Power Products Group, LLC.

NOT

FOR

REPRODUCTION

La page charge ...

Simplicity 071020-0 Manuel utilisateur

Marque: Simplicity

Modèle: 071020-0

Catégorie: Groupes électrogènes

Taper: Manuel utilisateur

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Simplicity 071020-0 User manual
español: Simplicity 071020-0 Manual de usuario

Simplicity 071020-0 Manuel utilisateur

Ce manuel convient également à

Simplicity 071020-0 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents