Simplicity 030545-00 Le manuel du propriétaire

Not for

Reproduction

BRIGGS & STRATTON POWER PRODUCTS GROUP, LLC

MILWAUKEE, WISCONSIN, U.S.A.

Manual No. 80006389 Revision A

Inverter Generator

Operator’s Manual

This generator is certified in accordance with CSA (Canadian Standards Association) standard C22.2 No. 100-14

(motors and generators) and rated in accordance with PGMA (Portable Generator Manufacturers’ Association)

standard PGMA G200 (Standard for Testing and Validating Performance of Portable Generators).

Not for

Reproduction

2 BRIGGSandSTRATTON.COM

BRIGGS & STRATTON POWER PRODUCTS is a registered

trademark of Briggs & Stratton Corporation

Milwaukee, WI, USA

Thank you for purchasing this quality-built Briggs & Stratton® generator. We are pleased that you’ve placed your

confidence in the Briggs & Stratton brand. When operated and maintained according to the instructions in this

manual, your Briggs & Stratton generator will provide many years of dependable service.

This manual contains safety information to make you aware of the hazards and risks associated with generators

and how to avoid them. This generator is designed and intended only for supplying electrical power for operating

compatible electrical lighting, appliances, tools and motor loads, and is not intended for any other purpose. It is

important that you read and understand these instructions thoroughly before attempting to start or operate this

equipment. Save these original instructions for future reference.

This generator requires final assembly before use. Refer to the Assembly section of this manual for

instructions on final assembly procedures. Follow the instructions completely.

Where to Find Us

You never have to look far to find Briggs & Stratton support and service for your generator. Consult your Yellow

Pages. There are over 30,000 Briggs & Stratton authorized service dealers worldwide who provide quality service.

You can also contact Briggs & Stratton Customer Service by phone at (800) 743-4115, or on the Internet at

www.briggsandstratton.com.

Register Your Product

To ensure prompt and complete warranty coverage, register your product online at www.onlineproductregistration.com.

Generator

Model Number _______________________

Revision

_____________________

Serial Number __________________

Date Purchased _____________________

Table of Contents

Operator Safety....................... 3

Assembly............................ 8

Features and Controls ................ 11

Operation........................... 14

Maintenance ........................ 18

Troubleshooting ..................... 23

Warranty ........................... 25

Product Specifications ................ 26

Common Service Parts ............... 26

Not for

Reproduction

3

Operator Safety

Safety Labels

The generator safety labels shown below and on the next page are placed on your portable generator to draw

attention to potential safety hazards.

Not for

Reproduction

4 BRIGGSandSTRATTON.COM

Not for

Reproduction

5

Equipment Description

Read this manual carefully and become familiar

with your generator. Know its applications, its

limitations and any hazards involved.

The generator is an engine–driven, revolving field,

alternating and direct current (AC & DC) generator. It

was designed to supply electrical power for operating

compatible electrical lighting, appliances, tools

and motor loads. The generator’s revolving field is





NOTICE Exceeding generators wattage/amperage

capacity can damage generator and/or electrical

devices connected to it.

• DO NOT exceed the generator’s wattage/amperage

capacity. See Don’t Overload Generator in the

Operation section.

Every effort has been made to ensure that the

information in this manual is both accurate and current.

However, the manufacturer reserves the right to

change, alter or otherwise improve the generator and

this documentation at any time without prior notice.

The Emission Control System for this generator is

warranted for standards set by the Environmental

Protection Agency and the California Air Resources

Board.

Important Safety Information

The manufacturer cannot possibly anticipate every

possible circumstance that might involve a hazard.

The warnings in this manual, and the tags and decals

affixed to the unit are, therefore, not all-inclusive.

If you use a procedure, work method or operating

technique that the manufacturer does not specifically

recommend, you must satisfy yourself that it is safe

for you and others. You must also make sure that the

procedure, work method or operating technique that

you choose does not render the generator unsafe.

Safety Symbols and Meanings

The safety alert symbol indicates a potential

personal injury hazard. A signal word (DANGER,

WARNING, or CAUTION) is used with the alert symbol

to designate a degree or level of hazard seriousness. A

safety symbol may be used to represent the type of

hazard. NOTICE indicates information considered

important, but not hazard-related.

DANGER indicates a hazard which, if not avoided,

will result in death or serious injury.

WARNING indicates a hazard which, if not

avoided, could result in death or serious injury.

CAUTION indicates a hazard which, if not

avoided, could result in minor or moderate injury.

NOTICE indicates information considered important,

but not hazard-related.

Fire

Explosion

Toxic Fumes

Hot Surface

Moving Parts

Electrical Shock

Kickback

Flying Objects

Operator’s Manual

Explosive

Pressure

Chemical

Burn

WARNING The engine exhaust from this

product contains chemicals known to the State of

California to cause cancer, birth defects, or other

reproductive harm.

WARNING Certain components in this product

and related accessories contain chemicals known to

the State of California to cause cancer, birth defects

or other reproductive harm. Wash hands after

handling.

Not for

Reproduction

6 BRIGGSandSTRATTON.COM

WARNING Storage batteries give off explosive

hydrogen gas during recharging.

Hydrogen gas stays near battery for

a long time after battery has been

charged. Slightest spark could ignite hydrogen

causing explosion resulting in death or serious

injury.

Battery electrolyte fluid contains acid and is

extremely caustic. Contact with battery fluid could

cause chemical burns resulting in serious injury.

• DO NOT allow any open flame, spark, heat, or lit

cigarette during and for several minutes after charging a

battery.

• Wear protective goggles, rubber apron, and rubber

gloves.

• DO NOT continue to charge a battery that becomes hot

or is fully charged.

• DO NOT leave battery unattended.

WARNING Starter cord kickback (rapid

retraction) will pull hand and arm toward

engine faster than you can let go which

could cause broken bones, fractures,

bruises, or sprains resulting in serious injury.

• When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices

plugged in and turned on.

WARNING POISONOUS GAS HAZARD.

Engine exhaust contains carbon monoxide,

a poisonous gas that could kill you in

minutes. You CANNOT smell it, see it, or

taste it. Even if you do not smell exhaust fumes, you

could still be exposed to carbon monoxide gas.

• Operate this product ONLY outside far away from

windows, doors and vents to reduce the risk of carbon

monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. Smoke

alarms cannot detect carbon monoxide gas.

• DO NOT run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors

and windows for ventilation. Carbon monoxide can

quickly build up in these spaces and can linger for hours,

even after this product has shut off.

• ALWAYS place this product downwind and point the

engine exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this

product, shut it off and get to fresh air RIGHT AWAY. See a

doctor. You may have carbon monoxide poisoning.

WARNING Fuel and its vapors are extremely

flammable and explosive which

could cause burns, fire or explosion

resulting in death or serious injury.

WHEN ADDING OR DRAINING FUEL

• Turn generator engine OFF and let it cool at least 2

minutes before removing fuel cap. Loosen cap slowly to

relieve pressure in tank.

• Fill or drain fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap and fittings frequently for

cracks or leaks. Replace if necessary.

• DO NOT light a cigarette or smoke.

WHEN STARTING EQUIPMENT

• Ensure spark plug, muffler, fuel cap, and air cleaner are

in place.

• DO NOT crank engine with spark plug removed.

WHEN OPERATING EQUIPMENT

• DO NOT operate this product inside any building, carport,

porch, mobile equipment, marine applications, or enclosure.

• DO NOT tip engine or equipment at angle which causes

fuel to spill.

• DO NOT stop engine by moving choke control to CHOKE

( ) position.

WHEN TRANSPORTING,

MOVING OR REPAIRING EQUIPMENT

• Transport/move/repair with fuel tank EMPTY or with fuel

shutoff valve OFF.

• DO NOT tip engine or equipment at angle which causes

fuel to spill.

• Disconnect spark plug wire.

STORING FUEL OR EQUIPMENT WITH FUEL IN TANK

• Store away from furnaces, stoves, water heaters, clothes

dryers, or other appliances that have pilot light or other

ignition source because they could ignite fuel vapors.

WARNING

• This generator does not meet U. S. Coast Guard

Regulation 33CFR-183 and should not be used on

marine applications.

• Failure to use the appropriate U. S. Coast Guard

approved generator could result in death or serious injury.

Not for

Reproduction

7

NOTICE

Exceeding generators wattage/amperage

capacity could damage generator and/or electrical

devices connected to it.

• DO NOT exceed the generator’s wattage/amperage

capacity. See Don’t Overload Generator in the Operation

section.

• Start generator and let engine stabilize before connecting

electrical loads.

• Connect electrical loads in OFF position, then turn ON for

operation.

• Turn electrical loads OFF and disconnect from generator

before stopping generator.

NOTICE

Improper treatment of generator could

damage it and shorten its life.

• Use generator only for intended uses.

• If you have questions about intended use, ask dealer or

contact local service center.

• Operate generator only on level surfaces.

• DO NOT expose generator to excessive moisture, dust,

dirt, or corrosive vapors.

• DO NOT insert any objects through cooling slots.

• If connected devices overheat, turn them off and

disconnect them from generator.

• Shut off generator if:

-electrical output is lost;

-equipment sparks, smokes, or emits flames;

-unit vibrates excessively.

WARNING Starter and other rotating parts

could entangle hands, hair, clothing, or

accessories resulting in serious injury.

• NEVER operate generator without protective housing or

covers.

• DO NOT wear loose clothing, jewelry or anything that

could be caught in the starter or other rotating parts.

• Tie up long hair and remove jewelry.

CAUTION Excessively high operating speeds

could result in minor injury.

Excessively low operating speeds impose a heavy

load.

• DO NOT tamper with governor spring, links or other parts

to increase engine speed. Generator supplies correct rated

frequency and voltage when running at governed speed.

• DO NOT modify generator in any way.

WARNING

Generator voltage could cause

electrical shock or burn resulting in death or

serious injury.

• DO NOT connect generator to a building’s electrical

system.

• DO NOT touch bare wires or receptacles.

• DO NOT use generator with electrical cords which are

worn, frayed, bare or otherwise damaged.

• DO NOT operate generator in the rain or wet weather.

• DO NOT handle generator or electrical cords while standing

in water, while barefoot, or while hands or feet are wet.

• DO NOT allow unqualified persons or children to operate

or service generator.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage

fuel tank causing a fire, resulting in

death or serious injury.

Contact with muffler area could cause burns

resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (1.5 m) of clearance on all sides of

generator including overhead.

• It is a violation of California Public Resource Code, Section

4442, to use or operate the engine on any forest-covered,

brush-covered, or grass-covered land unless the exhaust

system is equipped with a spark arrester, as defined in

Section 4442, maintained in effective working order. Other

states or federal jurisdictions may have similar laws.

Contact the original equipment manufacturer, retailer,

or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

• Replacement parts must be the same and installed in the

same position as the original parts.

WARNING Unintentional sparking could cause

fire or electric shock resulting in

death or serious injury.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Not for

Reproduction

8 BRIGGSandSTRATTON.COM

Assembly

Your generator requires some assembly and is ready

for use after it has been properly serviced with the

recommended fuel and oil.

If you have any problems with the assembly of

your generator, please call the generator helpline

at (800) 743-4115. If calling for assistance, please

have the model, revision, and serial number from the

identification label available. See Generator Features

and Controls for identification label location.

Unpack Generator

1. Set the carton on a rigid, flat surface.

2. Remove everything from carton except generator.

3. Open carton completely by cutting each corner

from top to bottom.

The generator is supplied with:

• Battery charge cables

• Operator’s manual

• Engine oil bottle

• Tool kit

• RV adapter plug

Add Engine Oil

1. Place generator on a level surface.

2. Loosen the two maintenance cover screws and

remove the side maintenance cover.

3. Clean area around oil fill and remove yellow oil fill cap.

4. Using oil funnel (optional), slowly pour contents of

provided oil bottle into oil fill opening to the point

of overflowing at oil fill cap.

NOTICE

Improper treatment of generator could

damage it and shorten its life.

• DO NOT attempt to crank or start the engine before it has

been properly serviced with the recommended oil. This

could result in an engine failure.

5. Replace oil fill cap and fully tighten.

6. Replace the maintenance cover and hand tighten

the two maintenance cover screws.

Add Fuel

Fuel must meet these requirements:

• Clean, fresh, unleaded gasoline.

• A minimum of 87 octane/87 AKI (91 RON). For high

altitude use, see High Altitude.

• Gasoline with up to 10% ethanol (gasohol) is acceptable.

NOTICE Use of unapproved fuels could damage

generator and voids warranty.

• DO NOT use unapproved gasoline such as E15 and E85.

• DO NOT mix oil in gasoline or modify engine to run on

alternate fuels.

To protect the fuel system from gum formation, mix in a

fuel stabilizer when adding fuel. See Storage. All fuel is

not the same. If you experience starting or performance

problems after using fuel, switch to a different fuel

provider or change brands. This engine is certified to

operate on gasoline. The emission control system for this

engine is EM (Engine Modifications).

1. Clean area around fuel fill cap, remove cap.

2. Slowly add unleaded fuel to red fuel level indicator (A)

in fuel tank. Be careful not to fill above the indicator.

This allows adequate space for fuel expansion.

3. Install fuel cap and let any spilled fuel evaporate

before starting engine.

WARNING Fuel and its vapors are extremely

flammable and explosive which

could cause burns, fire or explosion

resulting in death or serious injury.

WHEN ADDING FUEL

• Turn generator engine OFF and let it cool at least 2 minutes

before removing fuel cap. Loosen cap slowly to relieve

pressure in tank.

• Fill fuel tank outdoors.

• DO NOT overfill tank. Allow space for fuel expansion.

• If fuel spills, wait until it evaporates before starting engine.

• Keep fuel away from sparks, open flames, pilot lights,

heat, and other ignition sources.

• Check fuel lines, tank, cap and fittings frequently for

cracks or leaks. Replace if necessary.

• DO NOT light a cigarette or smoke.

A

Not for

Reproduction

9

High Altitude

At altitudes over 5,000 feet (1524 meters), a

minimum 85 octane / 85 AKI (89 RON) gasoline is

acceptable. To remain emissions compliant, high

altitude adjustment is required. Operation without

this adjustment will cause decreased performance,

increased fuel consumption, and increased emissions.

See a Briggs & Stratton Authorized Dealer for high

altitude adjustment information. Operation of the

engine at altitudes below 2,500 feet (762 meters) with

the high altitude kit is not recommended.

Grounding Fastener

The generator neutral is floating, which means that

the AC stator winding is isolated from the grounding

fastener and the AC receptacle ground pins. On a

floating neutral generator the AC receptacle ground

pins are not functional. Electrical devices, such as a

GFCI, requiring a functioning AC receptacle ground pin

will not operate.

Special Requirements

There may be Federal, local codes, or ordinances that

apply to the intended use of the generator. Please

consult a qualified electrician, electrical inspector, or

the local agency having jurisdiction:

• This generator has a floating neutral and is not for

use on job sites requiring a bonded neutral.

Portable Generator Location

Before starting the portable generator there are two

equally important safety concerns regarding carbon

monoxide poisoning and fire that must be addressed.

Operation Location to Reduce the Risk of Carbon

Monoxide Poisoning

All fossil fuel burning equipment, such as a portable

generator, contains carbon monoxide gas in the engine

exhaust, a poisonous gas that could kill you in minutes.

You cannot smell it, see it, or taste it. Even if you do

not smell exhaust fumes, you could still be exposed to

carbon monoxide gas.

By law it is required in many states to have a carbon

monoxide alarm (A) in operating condition in your

home. A carbon monoxide alarm is an electronic

device that detects hazardous levels of carbon

monoxide. When there is a buildup of carbon

monoxide, the alarm will alert the occupants by

flashing visual indicator light and alarm. Smoke alarms

cannot detect carbon monoxide gas.

A

WARNING POISONOUS GAS HAZARD.

Engine exhaust contains carbon monoxide,

a poisonous gas that could kill you in

minutes. You CANNOT smell it, see it, or

taste it. Even if you do not smell exhaust fumes, you

could still be exposed to carbon monoxide gas.

• Operate this product ONLY outside far away from

windows, doors and vents to reduce the risk of carbon

monoxide gas from accumulating and potentially being

drawn towards occupied spaces.

• Install battery-operated carbon monoxide alarms or

plug-in carbon monoxide alarms with battery back-up

according to the manufacturer’s instructions. Smoke

alarms cannot detect carbon monoxide gas.

• DO NOT run this product inside homes, garages,

basements, crawlspaces, sheds, or other partially-

enclosed spaces even if using fans or opening doors

and windows for ventilation. Carbon monoxide can

quickly build up in these spaces and can linger for hours,

even after this product has shut off.

• ALWAYS place this product downwind and point the

engine exhaust away from occupied spaces.

If you start to feel sick, dizzy, or weak while using this

product, get to fresh air RIGHT AWAY. See a doctor.

You may have carbon monoxide poisoning.

Install carbon monoxide alarms inside

your home. Without working carbon

monoxide alarms, you will not realize

you are getting sick and dying from

carbon monoxide poisoning.

CARBON MONOXIDE ALARM(S)

USE OUTDOORS - AVOID CARBON MONOXIDE POISONING

point away

from home

MUFFLER

Not for

Reproduction

10 BRIGGSandSTRATTON.COM

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage fuel

tank causing a fire, resulting in death or

serious injury.

• Portable generator must be at least 5 feet (1.5 m) from

any structure, overhang, trees, windows, doors, any wall

opening, shrubs, or vegetation over 12 inches (30.5 cm)

in height.

• DO NOT place portable generator under a deck or other

type of structure that may confine airflow.

• Smoke alarm(s) MUST be installed and maintained

indoors according to the manufacturer’s instructions/

recommendations. Carbon monoxide alarms cannot

detect smoke.

• DO NOT place portable generator in manner other than

shown.

1.5 m

(5 ft.) min.

1.5 m (5 ft.) min.

SILENCIEUX

Not for

Reproduction

11

Features and Controls

Read this Operator’s Manual and safety rules before operating your generator.

Compare the illustrations with your generator, to familiarize yourself with the locations of various controls

and adjustments. Save this manual for future reference.

F

E

P

M

A

G

R

S

N

K

H

C

B

D

T

A - Fuel Tank — Capacity of 5.7 L (1.5 U.S. gallons).

B - Choke Lever — Used when starting a cold engine.

C -

— Use

this switch to turn the QPT switch on and off.

D - Side Maintenance Cover — Remove to gain

access to the air cleaner and oil service.

E - Recoil Starter — Used to start the engine manually.

F - 12 Volt DC Receptacle — Use this receptacle with

battery charge cables to charge a 12 Volt battery. This

receptacle is protected by a push to reset circuit breaker.

G - Engine Switch — Set this switch to ON (I) before

using recoil starter. Set switch to OFF (0) to stop

engine. Also turns fuel valve on and off.

H - 120 Volt AC, 20 Amp, Duplex Receptacle —

May be used to supply electrical power for the

operation of 120 Volt AC, 20 Amp, single phase, 60

Hz electrical, lighting, appliance, tool, and motor loads.

J - Circuit Breakers — The 120 Volt AC, 20A duplex

receptacles are provided with “push to reset” circuit

breakers to protect the generator against electrical

overload.

K - 120 Volt AC, 30 Amp Locking Receptacle —

May be used to supply electrical power for the

operation of 120 Volt AC, 30 Amp, single phase, 60

Hz electrical lighting, appliance, tool and motor loads.

L - Retractable Handle — Press button and pull

handle out to move generator. Press button to push

handle back in.

M - USB Port — Use this port to recharge most USB

powered devices.

N - Parallel Operation Port — Use this port with

optional parallel operation kit to allow two

generators to run in parallel.

 — Built in LCD screen

to monitor certain features on the generator. See

STATSTATION™.

R - Grounding Fastener — Consult your local agency

having jurisdiction for grounding requirements in

your area.

S - Spark Arrester Muffler — Exhaust muffler lowers

engine noise and is equipped with a spark arrester

screen.

T - Top Maintenance Cover — Remove to gain

access to the spark plug.

Items Not Shown:

Air Cleaner (under side maintenance cover) —

Protects engine by filtering dust and debris out of

intake air.

Identification Label (under retractable handle)—

Provides model, revision, and serial number of

generator. Please have these readily available when

calling for assistance.

Oil Fill Cap (under side maintenance cover) —

Check and add engine oil here.

J

L

Not for

Reproduction

12 BRIGGSandSTRATTON.COM

Cord Sets and Receptacles

Use only high quality, well-insulated, grounded

extension cords with the generator’s receptacles.

Inspect extension cords before each use.

Check the ratings of all extension cords before you use

them. Check the operator’s manuals of devices for the

manufacturer’s recommendations.

120 Volt AC, 30 Amp Locking Receptacle

Use a NEMA L5–30 plug with this receptacle. Connect

a 3–wire cord set rated for 125 Volt AC loads at

30 Amps to the plug.

Use this receptacle to operate 120 Volt AC, 60 Hz,

single phase loads requiring up to 2,600 watts (2.6 kW)

of power at 21.6 Amps.

NOTICE

Receptacles may be marked with rating

value greater than generator output capacity.

• NEVER attempt to power a device requiring more

amperage than generator or receptacle can supply.

• DO NOT overload the generator. See Don’t Overload

Generator.

120 Volt AC, 20 Amp, Duplex Receptacles

The duplex receptacles are protected against overload

by push-to-reset circuit breakers.

Use receptacle to operate 120 Volt AC, single–phase,

60 Hz electrical loads requiring up to 2,400 watts (2.4

kW) at 20 Amps of current. Use cord sets that are

rated for 125 Volt AC loads at 20 Amps (or greater).

5 Volt DC USB Port

The maximum current available for the USB port is 1

Amp at 5 Volts. The USB port allows you to recharge

most USB powered devices with a USB charging cable

(not included).

NOTICE For charging ITE (Information Technology

Equipment) only.

12 Volt DC Receptacle

The maximum current available for the battery charge

circuit is 5 Amps. A DC circuit breaker protects this

receptacle from overloads. If an overload occurs, the circuit

breaker will trip (push button pops out). Wait a few minutes

and push the button in to reset the circuit breaker.

This receptacle allows you to recharge a 12 Volt

automotive or utility style storage battery with the

battery charge cable provided.

This receptacle can not be used to crank an engine

having a discharged battery. See Charging a Battery

before attempting to recharge a battery.

NOTICE When using the battery charge circuit and

USB port, turn the QPT switch to the OFF (0) position

for best performance.

WARNING Damaged or overloaded electrical

cords could overheat, arc, and burn

resulting in death or serious injury.

• ONLY use cords rated for your loads.

• Follow all safeties on electrical cords.

• Inspect cord sets before each use.

3-Wire Cord Set

Ground (Green)

NEMA L5-30

Neutral

120V

Hot

Not for

Reproduction

13

Parallel Operation Port

Two Briggs & Stratton inverter generators can be run

in parallel with a Briggs & Stratton parallel operation

kit (optional equipment). When running in parallel, the

total output of power is shown in chart.

Models Maximum Output

P2200 & P2200 3000 Watts

P2200 & P3000 3000 Watts

P3000 & P3000 4800 Watts



The control panel has a built in LCD display (A) to

monitor the following features:

• Load Monitor (Total Generator Load)

• Hour Meter (Total Generator Hours)

• Maintenance Reminder (Engine Maintenance)

Load Monitor

The load monitor measures the output wattage

(generator load) of all the generator receptacles and

will display the percentage of total generator load.

Hour Meter

The LCD on the control panel also has a built in hour

meter that displays and records how many hours your

generator has run (up to 999.9).

Maintenance Reminder

The LCD on the control panel also has a built in

maintenance reminder to alert you to change air filter,

change oil, and change spark plug. The LCD display

will flash every 50 hours for the different maintenance

intervals. See Maintenance Schedule for different

maintenance intervals.

Pressing the “View” button (B) will toggle between the

flashing load percentage and the flashing hour display.

Once maintenance has been performed, you must

push and hold the “View” button on the control panel

for a minimum of 3 seconds to stop the display from

flashing and return it to normal operation.

Output Indicator

The green LED output indicator light (C) comes

on when the generator is operating normally. It

indicates that the generator is producing power at the

receptacles.

Overload Alarm

The red LED overload alarm light (D) comes on and

cuts power to the receptacles if you overload the

generator. The green output indicator light will also go

off. If the generator was overloaded, you must turn off

and unplug all electrical loads, press the “Reset” button

(E) on the generator control panel and then plug in

and restart electrical loads one at a time to continue in

normal operating mode.

Low Oil Indicator

The low oil indicator system is designed to prevent

engine damage caused by not enough engine oil. If the

engine oil level drops below a preset level, the yellow

LED low oil indicator light (F) comes on and an oil level

switch will stop the engine. If the engine stops or the

yellow LED low oil indicator light comes on when you

pull the recoil handle, check the engine oil level.

D

F

A

E

C

B

Not for

Reproduction

14 BRIGGSandSTRATTON.COM

Operation

Starting the Engine

Disconnect all electrical loads from the generator. Use

the following start instructions:

1. Make sure unit is on a level surface.

NOTICE Failure to start and operate the unit on a

level surface will cause the unit not to start or shut

down during operation.

2. Turn the engine switch (A) to the ON (I) position.

3. Push choke lever (B) to CHOKE ( ) position.

NOTICE To start the engine for the very first time,

after running out of fuel or after a long period of

storage, fill fuel tank as described in Add Fuel. It will

require more than several start attempts until the air in

the fuel system has been purged.

4. Grasp recoil handle and pull slowly until slight

resistance is felt. Then pull rapidly to start engine.

• If engine starts, proceed to step 6.

• If engine fails to start, proceed to step 5.

5. Move choke lever to half choke position, and pull

recoil handle twice.

• If engine fails to start, repeat steps 3 thru 4.

6. Slowly move choke lever to RUN (

) position. If

engine falters, move choke lever to half choke

position until engine runs smoothly, and then to

RUN ( ) position.

NOTICE If engine floods, move choke lever to

RUN ( ) position and crank until engine starts.

NOTICE If engine starts after 3 pulls but fails to run,

or if unit shuts down during operation, make sure unit

is on a level surface and check for proper oil level

in crankcase. This unit is equipped with a low oil

protection device. If so, oil must be at proper level for

engine to start.

B

WARNING Starter cord kickback (rapid

retraction) will pull hand and arm toward

engine faster than you can let go which could

cause broken bones, fractures, bruises, or

sprains resulting in serious injury.

• When starting engine, pull cord slowly until resistance is

felt and then pull rapidly to avoid kickback.

• NEVER start or stop engine with electrical devices

plugged in and turned on.

WARNING Exhaust heat/gases could ignite

combustibles, structures or damage

fuel tank causing a fire, resulting in

death or serious injury.

Contact with muffler area could cause burns

resulting in serious injury.

• DO NOT touch hot parts and AVOID hot exhaust gases.

• Allow equipment to cool before touching.

• Keep at least 5 feet (1.5 m) of clearance on all sides of

generator including overhead.

• It is a violation of California Public Resource Code,

Section 4442, to use or operate the engine on any forest-

covered, brush-covered, or grass-covered land unless

the exhaust system is equipped with a spark arrester, as

defined in Section 4442, maintained in effective working

order. Other states or federal jurisdictions may have

similar laws.

Contact the original equipment manufacturer, retailer,

or dealer to obtain a spark arrester designed for the

exhaust system installed on this engine.

• Replacement parts must be the same and installed in the

same position as the original parts.

A

Not for

Reproduction

15

Connecting Electrical Loads

1. Make sure the green output indicator light comes

on (it may take up to three seconds).

2. Let engine stabilize and warm up for a few

minutes after starting.

3. Plug in and turn on the desired 120 Volt AC,

single phase, 60 Hz electrical loads.

NOTICE When plugging into the 120 Volt duplex

receptacles, plug items to be powered in sequence as

shown below.

NOTICE

• DO NOT connect 240 Volt loads to the 120 Volt

receptacles.

• DO NOT connect 3-phase loads to the generator.

• DO NOT connect 50 Hz loads to the generator.

• DO NOT OVERLOAD THE GENERATOR. See

Don’t Overload Generator.

NOTICE

Exceeding generators wattage/amperage

capacity could damage generator and/or electrical

devices connected to it.

• DO NOT exceed the generator’s wattage/amperage

capacity. See Don’t Overload Generator in the

Operation section.

• Start generator and let engine stabilize before

connecting electrical loads.

• Connect electrical loads in OFF position, then turn

ON for operation.

• Turn electrical loads OFF and disconnect from

generator before stopping generator.

Parallel Operation

Two Briggs & Stratton inverter generators can be run

in parallel with a Briggs & Stratton parallel operation

kit (optional equipment). When running in parallel, the

total output of power is shown in chart.

NOTICE Total electrical load connected to the

parallel kit must not exceed the maximum output.

See the parallel operation kits instruction sheet for

detailed instructions on installation and operation of the

connected generators.

NOTICE

• Turn electrical loads OFF and disconnect from

both generators.

• The QPT switch must be in the same position on

both generators.

• Connect the power cables to both generators

before starting the engines. See instruction sheet

supplied with parallel kit.

• Start engine on one of the inverter generators

according to Starting the Engine.

• Once the green LED output indicator light on the

first generators is steady, start second generator.

• Connect and turn on electrical loads to the parallel

panel receptacles.

• DO NOT disconnect power cables after engines

have been started.

• Shut down engines as described in Stopping the

Engine.

1

2

3

4

Models Maximum Output

P2200 & P2200 3000 Watts

P2200 & P3000 3000 Watts

P3000 & P3000 4800 Watts

Not for

Reproduction

16 BRIGGSandSTRATTON.COM

Stopping the Engine

1. Turn OFF and unplug all electrical loads from generator

panel receptacles. NEVER start or stop engine with

electrical devices plugged in and turned ON.

2. Let engine run at no-load for several minutes to

stabilize internal temperatures of engine and generator.

3. Turn engine switch to the OFF (0) position.



This feature is designed to greatly improve fuel

economy. When this switch is turned ON, the engine

speed will increase as electrical loads are connected,

and decreased as electrical loads are removed.

With the switch off, the engine will run at full

governed speed.

NOTICE Always have the switch OFF when starting or

stopping the generator or when using the DC receptacle.

Charging a Battery

Your generator has the capability of recharging a discharged

12 Volt automotive or utility style storage battery.

NOTICE

• Not for use with any other type of battery.

• DO NOT use the unit to charge any 6 Volt batteries.

• DO NOT use the unit to crank an engine having a

discharged battery.

To recharge 12 Volt batteries, proceed as follows:

1. Make sure QPT switch is in OFF (0) position.

2. If necessary, clean battery posts or terminals.

3. Check fluid level in all battery cells. If necessary,

add ONLY distilled water to cover separators in

battery cells. DO NOT use tap water.

4. If the battery is equipped with vent caps, make

sure they are installed and are tight.

5. Connect battery charge cable clamp with red

handle to battery post or terminal indicated by

Positive, POS or (+).

6. Connect battery charge cable clamp with black

handle to battery post or terminal indicated by

Negative, NEG, or (–).

7. Connect battery charge cable connector plug to

the 12 Volt DC panel receptacle.

8. Start generator as described in Starting The

Engine. Let the engine run while battery

recharges.

NOTICE Normally a period of 30 to 120 minutes is

sufficient to recharge a weak battery.

9. When battery has charged, shut down engine as

described in Stopping The Engine.

10. Remove the battery charging cable from the

generator and then disconnect from the battery

posts.

NOTICE Use an automotive hydrometer to test battery

state of charge and condition. Follow the hydrometer

manufacturer’s instructions carefully. Generally, a battery

is considered to be at 100% state of charge when

specific gravity of its fluid (as measured by hydrometer)

is 1.260 or higher.

WARNING Battery posts, terminals and related

accessories contain lead and lead compounds,

chemicals known to the State of California to cause

cancer and reproductive harm. Wash hands after

handling.

WARNING Fuel and its vapors are extremely

flammable and explosive which could

cause burns, fire or explosion

resulting in death or serious injury.

• DO NOT stop engine by moving choke lever to CHOKE

position

( ).

WARNING Storage batteries give off explosive

hydrogen gas during recharging.

Hydrogen gas stays near battery for

a long time after battery has been

charged. Slightest spark could ignite

hydrogen causing explosion resulting in death or

serious injury.

Battery electrolyte fluid contains acid and is

extremely caustic. Contact with battery fluid could

cause chemical burns resulting in serious injury.

• DO NOT allow any open flame, spark, heat, or

lit cigarette during and for several minutes after

charging a battery.

• Wear protective goggles, rubber apron, and rubber

gloves.

• DO NOT continue to charge a battery that

becomes hot or is fully charged.

• DO NOT leave battery unattended.

Not for

Reproduction

17

Don’t Overload Generator

Capacity

You must make sure your generator can supply

enough rated (running) and surge (starting) watts for

the items you will power at the same time. Follow these

simple steps:

1. Select the items you will power at the same time.

2. Total the rated (running) watts of these items.

This is the amount of power your generator must

produce to keep your items running. See Wattage

Reference Guide.

3. Estimate how many surge (starting) watts you will

need. Surge wattage is the short burst of power

needed to start electric motor-driven tools or

appliances such as a circular saw or refrigerator.

Because not all motors start at the same time, total

surge watts can be estimated by adding only the

item(s) with the highest additional surge watts to

the total rated watts from step 2.

Example:

Total Rated (Running) Watts = 1555

Highest Additional Surge Watts = 600

Total Generator Output Required = 2155

Power Management

To prolong the life of your generator and attached

devices, it is important to take care when adding

electrical loads to your generator. There should be

nothing connected to the generator outlets before

starting its engine. The correct and safe way to manage

generator power is to sequentially add loads as follows:

1. With nothing connected to the generator, start the

engine as described in this manual.

2. Plug in and turn on the first load, preferably the

largest load you have.

3. Permit the generator output to stabilize (engine

runs smoothly and attached device operates

properly).

4. Plug in and turn on the next load.

5. Again, permit the generator to stabilize.

6. Repeat steps 4 and 5 for each additional load.

NEVER add more loads than the generator capacity.

Take special care to consider surge loads in generator

capacity, as described above.

* Wattages listed are approximate only. Check tool or

appliance for actual wattage.

Tool or

Appliance

Rated

(Running)

Watts

Additional

Surge

(Starting)

Watts

Window Fan 300 600

Deep Freezer 500 500

Television 500 —

Security System 180 —

Light (75 Watts) 75 —

1555 Total

Running Watts

600 Highest

Surge Watts

Wattage Reference Guide

Tool or Appliance

Rated*

(Running)

Watts

Additional

Surge

(Starting)

Watts

Essentials

Light Bulb - 75 watt 75 —

Deep Freezer 500 500

Sump Pump 800 1200

Refrigerator/Freezer - 18 cf 800 1600

Water Well Pump - 1/3 hp 1000 2000

Heating/Cooling

Window AC - 10,000 BTU 1200 1800

Window Fan 300 600

Furnace Fan Blower - 1/2 hp 800 1300

Kitchen

Microwave Oven - 1000 Watt 1000 —

Coffee Maker 1500 —

Electric Stove - Single Element 1500 —

Hot Plate 2500 —

Family Room

DVD/CD Player 100 —

VCR 100 —

Stereo Receiver 450 —

Color Television - 27 in 500 —

Personal Computer w/17 in monitor 800 —

Other

Security System 180 —

AM/FM Clock Radio 300 —

Garage Door Opener - 1/2 hp 480 520

Electric Water Heater - 40 gallon 4000 —

DIY

Quartz Halogen Work Light 1000 —

Airless Sprayer - 1/3 hp 600 1200

Reciprocating Saw 960 960

Electric Drill - 1/2 hp 1000 1000

Circular Saw - 7-1/4 in 1500 1500

Miter Saw - 10 in 1800 1800

Table Planer - 6 in 1800 1800

Table Saw/Radial Arm Saw - 10 in 2000 2000

Air Compressor - 1-1/2 hp 2500 2500

Not for

Reproduction

18 BRIGGSandSTRATTON.COM

Maintenance

Maintenance Schedule

Follow the hourly or calendar intervals, whichever

occurs first. More frequent service is required when

operating in adverse conditions noted below.

1

Service more often under dirty or dusty conditions.

General Recommendations

Regular maintenance will improve the performance

and extend the life of the generator. See any

authorized dealer for service.

The generator’s warranty does not cover items that

have been subjected to operator abuse or negligence.

To receive full value from the warranty, the operator

must maintain the generator as instructed in this

manual.

NOTICE

Improper treatment of generator could

damage it and shorten its life.

• NEVER operate generator without protective housing or

covers to assure proper cooling.

Some adjustments will need to be made periodically to

properly maintain your generator.

All service and adjustments should be made at least

once each season. A new spark plug and clean

air filter assure proper fuel-air mixture and help

your engine run better and last longer. Follow the

requirements in the Maintenance Schedule chart

above.

Emissions Control

Maintenance, replacement, or repair of the

emissions control devices and systems may

be performed by any non-road engine repair

establishment or individual. However, to obtain

”no charge” emissions control service, the work must

be performed by a factory authorized dealer. See the

Emissions Warranty.

• Generator is equipped with a G-trim engine.

Generator Maintenance

Generator maintenance consists of keeping the unit

clean and dry. Operate and store the unit in a clean dry

environment where it will not be exposed to excessive

dust, dirt, moisture, or any corrosive vapors. Cooling

air slots in the generator must not become clogged

with snow, leaves, or any other foreign material.

NOTICE DO NOT use water or other liquids to clean

generator. Liquids can enter engine fuel system,

causing poor performance and/or failure to occur. In

addition, if liquid enters generator through cooling air

slots, some of the liquid will be retained in voids and

cracks of the rotor and stator winding insulation. Liquid

and dirt buildup on the generator internal windings will

eventually decrease the insulation resistance of these

windings.

Cleaning

Daily or before use, look around and underneath

the generator for signs of oil or fuel leaks. Clean

accumulated debris from inside and outside the

generator. Keep the linkage, spring and other engine

controls clean. Keep the area around and behind

the muffler free from any combustible debris. Inspect

cooling air slots and openings on generator. These

openings must be kept clean and unobstructed.

Engine parts should be kept clean to reduce the risk of

overheating and ignition of accumulated debris:

• Use a damp cloth to wipe exterior surfaces clean.

NOTICE

Improper treatment of generator could

damage it and shorten its life.

• DO NOT expose generator to excessive moisture, dust,

dirt, or corrosive vapors.

• DO NOT insert any objects through cooling slots.

• Use a soft bristle brush to loosen caked on dirt or

oil.

• Use a vacuum cleaner to pick up loose dirt and

debris.

Every 8 Hours or Daily

• Clean debris

• Check engine oil level

First 10 Hours

• Change engine oil

Every 50 Hours or 3 Months

• Service engine air cleaner and breather filter

1

• Change engine oil

1

Every 100 Hours or 6 Months

• Clean fuel strainer

• Service spark plug

• Inspect muffler and spark arrester

Not for

Reproduction

19

Cleaning Fuel Strainer

The fuel strainer helps prevent debris from entering the

fuel system.

Clean the fuel strainer as follows:

1. Make sure generator is on a level surface.

2. Remove the fuel cap (A) and fuel strainer (B).

3. Wash fuel strainer in liquid detergent and water.

4. Wipe fuel strainer clean with a clean, dry cloth.

5. Carefully reinstall the fuel strainer and fuel cap.

Engine Maintenance

Oil

Oil Recommendations

We recommend the use of Briggs & Stratton Warranty

Certified oils for best performance. Other high-quality

detergent oils are acceptable if classified for service SF,

SG, SH, SJ or higher. DO NOT use special additives.

Outdoor temperatures determine the proper oil viscosity

for the engine. Use the chart to select the best viscosity

for the outdoor temperature range expected.

* Below 40°F (4°C) the use of SAE 30 will result in hard

starting.

** Above 80°F (27°C) the use of 10W30 may cause

increased oil consumption. Check oil level more frequently.

Checking Oil Level

Oil level should be checked prior to each use or

at least every 8 hours of operation. Keep oil level

maintained.

1. Make sure generator is on a level surface.

2. Loosen the side maintenance cover screws and

remove the side maintenance cover.

3. Clean area around oil fill and remove oil fill cap.

4. Verify oil is at the point of overflowing at oil fill

opening.

5. Replace and tighten oil fill cap.

6. Reinstall the side maintenance cover and hand

tighten the cover screws.

Adding Engine Oil

1. Make sure generator is on a level surface.

2. Repeat steps 2 through 4 to check oil level as

described in Checking Oil Level.

3. If needed, slowly pour oil into oil fill opening to the

point of overflowing at oil fill.

4. Replace and tighten oil fill cap.

5. Reinstall the side maintenance cover and hand

tighten the cover screws.

B

A

WARNING Unintentional sparking could cause

fire or electric shock resulting in

death or serious injury.

WHEN ADJUSTING OR MAKING REPAIRS TO YOUR

GENERATOR

• Disconnect the spark plug wire from the spark plug and

place the wire where it cannot contact spark plug.

WHEN TESTING FOR ENGINE SPARK

• Use approved spark plug tester.

• DO NOT check for spark with spark plug removed.

Not for

Reproduction

20 BRIGGSandSTRATTON.COM

Changing Engine Oil

If you are using your generator under extremely dirty or

dusty conditions, or in extremely hot weather, change

the oil more often.

KEEP OUT OF REACH OF CHILDREN.

DON’T POLLUTE. CONSERVE

RESOURCES. RETURN USED OIL TO

COLLECTION CENTERS.

Change the oil while the engine is still warm from

running, as follows:

1. Make sure generator is on a level surface.

2. Loosen the side maintenance cover screws and

remove the side maintenance cover.

3. Clean area around oil fill and remove oil fill cap.

4. Tip your generator to drain oil from oil fill into a

suitable container making sure you tip your unit

toward the oil filler neck. When crankcase is

empty, return generator to upright position.

5. Slowly pour oil (about 20 oz.) into oil fill opening to the

point of overflowing at oil fill cap. DO NOT overfill.

6. Reinstall oil fill cap. Finger tighten cap securely.

7. Wipe up any spilled oil.

8. Reinstall the side maintenance cover and hand

tighten the cover screws.

Service Air Cleaner

Your engine will not run properly and may be damaged

if you run it with a dirty air cleaner. Service more often

if operating under dirty or dusty conditions.

To service the air cleaner, follow these steps:

1. Loosen the side maintenance cover screws and

remove the side maintenance cover.

2. Loosen air cleaner cover screw (A) and remove

air cleaner cover (B).

3. Carefully remove foam air cleaner (C) by pulling it

out towards you.

4. Carefully remove breather filter (D) by pulling it out

towards you.

5. Wash foam air cleaner and breather filter in liquid

detergent and water only. Squeeze dry in a clean

cloth.

6. SATURATE foam air cleaner in clean engine oil

and squeeze in a clean cloth to remove excess oil.

7. Reinstall clean or new foam air cleaner inside

base.

8. Reinstall clean or new breather filter inside base.

9. Reinstall the air cleaner cover and tighten screw.

10. Reinstall the side maintenance cover and hand

tighten the cover screws.

Service Spark Plug

Changing the spark plug will help your engine to start

easier and run better.

1. Push in on tab with screwdriver and remove top

maintenance cover.

CAUTION Avoid prolonged or repeated skin

contact with used motor oil.

• Used motor oil has been shown to cause skin cancer in

certain laboratory animals.

• Thoroughly wash exposed areas with soap and water.

C

B

D

A

La page charge ...

Simplicity 030545-00 Le manuel du propriétaire

Ce manuel convient également à

Simplicity 030545-00 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents