www.lexmark.com
810 Series Color Jetprinter™
Unpack your printer.
Note: Contents may vary based on geography.
1
Note: You may need to purchase a USB
cable separately.
Connect the power cord.
2
Make sure the power is on.
3
Remove the sticker and tape from the bottom of the
print cartridges.
7
Open the cartridge lids, insert the cartridges, and snap the lids closed.
8
Close the access cover.
9
21G0070
Raise the access cover.
6
Safety information
• Use only the power supply provided with this product or the
manufacturer's authorized replacement power supply.
• Connect the power supply cord to an electrical outlet that is
near the product and easily accessible.
• Refer service or repairs, other than those described in the
user documentation, to a professional service person.
CAUTION: Do not set up this product or make any electrical or
cabling connections, such as the power supply cord, during a
lightning storm.
Load paper and adjust the paper guide.
10
Extend the paper exit tray.
5
Raise the paper support.
4
Steps 11 - 14
Your printer may include a photo cartridge
instead of a black print cartridge.
Before you continue, remove the photo
cartridge from the print cartridge storage unit.
Reminder: Save the print cartridge storage
unit to protect unused cartridges.
Setup Troubleshooting Have a question?
• Refer to the User’s Guide.
For Windows:
Click Start
à Programs or All Programs à Lexmark 810 Series à User’s Guide.
For Mac OS X:
1 From your desktop, double-click the Lexmark 810 Series folder alias.
2 Double-click the Lexmark 810 Series.help alias.
• Refer to the Lexmark Solution Center software.
1 Click Start
à Programs or All Programs à Lexmark 810 Series à Lexmark Solution Center.
2 Click the Troubleshooting tab on the left side of the screen.
• Visit our Web site: http://support.lexmark.com/
• Call us at 1-800-332-4120.
Monday-Friday (9:00 AM - 9:00 PM EST)
Saturday (Noon-6:00 PM EST)
Note: Phone number and support times may change without notice.
Record the following information (located on your store receipt and the back of your printer) and have it ready
when you contact us so that we may serve you faster:
Machine Type number
Serial number
Date purchased
Store where purchased
Symptom: Diagnosis: Solution:
The Power light is not lit Is the power cord pushed all the way into the printer? Disconnect the power cord from the wall outlet, and then
from the printer. Reconnect the power cord by pushing it all
the way into the connector on the printer, and then into the
wall outlet.
Is the printer connected to a working electrical outlet? Connect the printer to an electrical outlet that other electrical
devices have been using.
Software will not install Is your operating system compatible with the printer? The printer supports these operating systems:
• Windows 98
• Windows Me
• Windows 2000
• Windows XP
• Mac OS X version 10.1.5
• Mac OS X version 10.2.3 and later
Alignment page or test page will not print Is the printer on? Press the Power button. If the Power light does not come
on, see the “The Power light is not lit” symptom at the
beginning of this table.
Do you see an error message on the monitor or flashing
lights on the printer?
See “Error messages troubleshooting” in your User’s Guide.
Is your printer connected to your computer through another
device, such as a USB hub or switch box?
Disconnect the USB cable from any other devices and
directly connect it between the printer and your computer.
For help, see step 12.
Did you remove the sticker and tape from the bottom of each
print cartridge?
Are the print cartridges installed properly?
Remove the print cartridges, check for the sticker and tape
and then reinsert them. For help, see step7 and step 8.
Is the paper loaded correctly? See step 10.
Insert the CD.
Follow the instructions on your screen to
complete installation.
14
Make sure your computer is on.
11
Attach the USB cable to your printer and computer.
12
Need more ink?
The following cartridges work with your printer.
Federal Communications Commission (FCC)
compliance information statement
This product complies with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. Refer to the
• 31 • 32
• 34
• 33
• 35
If you inserted the CD and the install screen did not appear (Windows):
1 Click Cancel on any Add New Hardware screens.
2 Eject and reinsert the printer software CD.
If the printer software install screen does not appear:
a From your desktop, double-click My Computer (In Windows XP, click Start
à My Computer).
b Double-click the CD-ROM drive icon. If necessary, double-click setup.exe.
c When the printer software install screen appears, click Install.
d Follow the instructions on the screen to complete the installation.
If you inserted the CD and the install screen did not appear (Mac):
1 From your desktop, double-click the Lexmark 810 Series Installer icon.
2 Double-click Install and follow the instructions on the screen.
P/N 21G0070 E.C. 21G005
© 2004 Lexmark International, Inc. All rights reserved.
Note: New Hardware screens appear only for Windows users. For Macintosh, continue to step 14.
13
Windows 2000/XP
Windows 98/Me
Important!
Click Cancel on the New Hardware screen.
-
1
-
2
Lexmark 810 series Install Manual
- Taper
- Install Manual
- Ce manuel convient également à
dans d''autres langues
- English: Lexmark 810 series
Documents connexes
-
Lexmark 810 Series Color Jetprinter Guide de démarrage rapide
-
-
-
Lexmark 22W0000 - P 350 Color Inkjet Printer Manuel utilisateur
-
-
-
Lexmark 2200 Manuel utilisateur
-
-
-