Bissell PowerGlide Pet 1044 SERIES Manuel utilisateur

Earn BISSELL Rewards!

Register your

product today!

See details on

back page

2

Thank You

USER'S GUIDE

1044 SERIES

Safety Instructions

Product View

Assembly

Operations

Maintenance and Care

Troubleshooting

Consumer Care

Replacement Parts

3

4

5-6

6-10

11-16

17

20

18

Accessories

Warranty

18

19

Earn BISSELL Rewards!

Register your

product today!

See details on

back page

www.bissell.com 800.237.7691

Thanks for buying a BISSELL vacuum

We’re glad you purchased a BISSELL vacuum. Everything we know about

floor care went into the design and construction of this complete, high-tech

home cleaning system.

Your BISSELL vacuum is well made, and we back it with a limited three

year warranty. We also stand behind it with a knowledgeable, dedicated

Consumer Care department, so, should you ever have a problem, you’ll

receive fast, considerate assistance.

My great-grandfather invented the floor sweeper in 1876. Today, BISSELL

is a global leader in the design, manufacture, and service of high quality

homecare products like your BISSELL vacuum.

Thanks again, from all of us at BISSELL.

Mark J. Bissell

Chairman & CEO

2

www.bissell.com 800.237.7691

IMPORTANT SAFETY INSTRUCTIONS

3

When using an electrical

appli-

ance, basic precautions should be

observed, including the following:

READ ALL INSTRUCTIONS

BEFORE USING YOUR

UPRIGHT VACUUM.

Always connect to a polarized outlet (left slot is

wider than right). Unplug from outlet when not

in use and before conducting maintenance.

WARNING: To

reduce the risk of fire, electric shock, or injury:

■

Do not modify the polarized plug to fit a

non-polarized outlet or extension cord.

■

Do not leave vacuum cleaner unattended

when it is plugged in.

■

Unplug from outlet when not in use and

before servicing.

■

Unplug before attaching the Pet

TurboBrush Tool.

■

Do not use outdoors or on wet surfaces.

■

Do not allow children to operate vacuum

cleaner or use as a toy.

■

Close attention is necessary when used

by or near children.

■

Do not use for any purpose other than

described in this user’s guide.

■

Use only manufacturer’s recommended

attachments.

■

Do not use with damaged cord or plug.

■

If appliance is not working as it should,

has been dropped, damaged, left

outdoors, or dropped into water, have it

repaired at an authorized service center.

■

Do not pull or carry by cord, use cord as

a handle, close a door on cord, or pull

cord around sharp edges or corners.

Do not run appliance over cord. Keep

cord away from heated surfaces.

■

Do not unplug by pulling on cord. To

unplug, grasp the plug, not the cord.

■

Do not handle vacuum cleaner or plug

with wet hands.

■

Do not put any object into openings.

Do not use with any opening blocked;

keep openings free of dust, lint, hair,

and anything that may reduce air flow.

■

Keep hair, loose clothing, fingers, and

all parts of body away from openings

and moving parts.

■

Turn off all controls before plugging

or unplugging vacuum cleaner.

■

Use extra care when cleaning stairs.

■

Do not pick up flammable materials (lighter

fluid, gasoline, kerosene, etc.) or use in the

presence of explosive liquids or vapors.

■

Do not pick up toxic material (chlorine

bleach, ammonia, drain cleaner, etc.).

■

Do not use vacuum cleaner in an

enclosed space filled with vapors given

off by oil base paint, paint thinner, some

moth proofing substances, flammable

dust, or other explosive or toxic vapors.

■

Do not pick up hard or sharp objects

such as glass, nails, screws, coins, etc.

■

Do not pick up anything that is burning or

smoking, such as cigarettes, matches, or

hot ashes.

■

Do not use without filters in place.

■

Use only on dry, indoor surfaces.

■

Keep appliance on a level surface.

■

Do not carry the vacuum cleaner while

it is running.

SAVE THESE

INSTRUCTIONS

FOR FUTURE USE

THIS APPLIANCE

HAS A

POLARIZED PLUG

To reduce the risk of electric shock, this

appliance has a polarized plug (one

blade is wider than the other). This plug

will fit in a polarized outlet only one way.

If the plug does not fit fully in the outlet,

reverse the plug. If it still does not fit,

contact a qualified electrician to install

a proper outlet. Do not change the plug

in any way.

This model is for household use only.

www.bissell.com 800.237.7691

4

Product view

WARNING:

Do not plug in your vacuum cleaner

until you are familiar with all

instructions and operating procedures.

Handle

Power

Switch

Easy

Empty

™

Dirt

Container

Height

Adjustment

Knob

Washable

Pre-Motor

Filter

Carry

Handle

Lock ‘n Seal

®

Lever

Febreze

®

Post-Motor

Filter*

Wide Cleaning Foot

Upper

Tank

Power

Cord

Crevice Tool

Dusting Brush/

Upholstery Tool

Twist ‘n Snap™

Hose

Handle

Release

Pedal

Hose

Cuff

Hose

Wand

Base

Extension

Wand

Hose

Clip

Stretch Hose

Quick

Release

™

Cord Wrap

Pet

TurboBrush

®

Tool

*Select models include a Febreze post-motor

filter. For ordering information, turn to page 18.

Febreze and related trademarks are owned by

The Procter & Gamble Company, Cincinnati,

Ohio and used under license by BISSELL

Homecare, Inc.

www.bissell.com 800.237.7691

Assembly

5

WARNING:

Plastic film can be dangerous. To

avoid danger of suffocation, keep

away from babies and children.

The only tool you'll need to

assemble your vacuum cleaner

is a Phillips screwdriver.

Attach handle to vacuum

1. Locate the handle and cord wrap.

Remove the screw packet taped to

the handle.

2. Stand the vacuum upright and from

the rear of the unit, slide the base

of the handle firmly into the grooves

at the top of the vacuum body.

3. Ensure that the handle fits firmly to

the vacuum body. If there are any

gaps, continue to push firmly until

the handle is secure.

4. Insert the provided screw into the

existing hole, attaching the handle

to the body of the vacuum. Tighten

securely with a screwdriver.

2.

4.

www.bissell.com 800.237.7691

Assembly

Operations

6

Attach vacuum hose and tools

1. Attach the Twist ‘n Snap Hose by

lining up the tabs on the base with the

corresponding notches on the back of

the vacuum as shown.

2. Turn the Twist ‘n Snap Hose to the right

to lock the hose into place.

3. Grasping the Quick Reach Handle,

slide the end of the Hose Wand onto

the Hose Wand Base. Snap the Hose

into the Hose Clip.

NOTE: The vacuum will not

operate effectively unless the

hose wand is firmly attached.

4. Slide the extension wand and crevice

tool into the storage clip on back

of vacuum.

5. Slide the dusting brush/upholstery tool

into the storage clip on back of vacuum.

6. Store the Pet TurboBrush Tool on the front

of the handle by lining up the base of the

Tool with the base of the holder. Push back

and the Tool will snap into place.

Power switch

The Power Switch is located on the left

side of the vacuum. Push the rocker switch

“ON” (I) to vacuum, and “OFF” (O) when

cleaning is complete.

NOTICE:

For above floor cleaning, the floor

brush will continue to rotate but is

raised above floor. To prevent carpet

damage, do not lean on the vacuum

or let the powerfoot tilt forward.

CAUTION:

To avoid personal injury and

to prevent the cleaner from

falling when cleaning stairs,

always place it at the bottom

of the stairs.

CAUTION:

Before using your vacuum,

make sure that the dirt

container is in the locked

position and that all filters

(pre-motor and post-motor)

are in place. Do not operate

your vacuum without

these filters.

1.

3.

Twist 'n

Snap Hose

6.

www.bissell.com 800.237.7691

7

Operations

Handle positions

Press the handle release pedal, located on

the lower left side of the vacuum, with your

foot to place your vacuum into one of three

cleaning positions.

1. Upright – For storage and above

floor cleaning with tools.

2. Normal Cleaning – Press handle

release pedal once. Position used for

most household floor cleaning tasks.

3. Low Cleaning – With the vacuum

in normal cleaning position, press

handle release pedal again. Use for

reaching under low furniture such as

tables, chairs or beds.

Height adjustment

The powerfoot/rotating floor brush on your

vacuum can be adjusted to clean several

floor surfaces.

NOTE: For optimal cleaning

performance, adjust to the

lowest practical setting. If your

cleaner is difficult to push, adjust

to the next higher setting.

1. Turn height adjustment knob to

desired setting.

Bare Floor

For non-carpeted, indoor surfaces

Lowest Setting

For short pile carpets

Medium Setting

For short and medium pile carpets

Highest Setting

For plush pile carpet

Tip:

Before cleaning under low furniture,

check area first for objects that might

harm the unit or block the vacuum hose.

1.

2.

3.

1.

Height Adjustment Knob

www.bissell.com 800.237.7691

Operations

8

Transporting cleaner

1. To move your cleaner from room to

room, put the handle in the upright

position, tilt the cleaner back on its rear

wheels and push forward.

2. The cleaner can also be moved by

using the carry handle.

Special on-board tools

Your vacuum is not only a powerful carpet

and rug cleaner, it’s also a versatile above

floor vacuum cleaner when you select one of

the special tools.

1. Raise the handle to the upright position.

2. Grasp the Hose Cuff to separate from

Hose Base.

3. Attach tools by firmly pushing onto

vacuum hose, hose wand or extension

wand. Be sure the hose and tool fit

snuggly together by twisting tightly.

Dusting Brush/Upholstery Tool:

Two types of cleaning tools in one

attachment.

 •Usethedustingbrushtodust

furniture, blinds, books, lamps,

shelves and baseboards.

 •Slidethebrushofftousethe

upholstery tool on cushions,

draperies and fabrics.

correct way to carry

1.

Dusting Brush/

Upholstery Tool

Extension Wand

Crevice Tool

Hose

Base

Special on-board tools (cont)

Crevice Tool: Use in tight narrow spaces.

Extension Wand: Use with desired

attachment for a longer reach.

Hose Wand: Use with desired attachment

for a longer reach or for cleaning hard

to reach places.

Pet TurboBrush Tool: Use rotating

brush action for small flat areas such

as cushions and beds.

NOTE: Press gently down and

pull towards you in a raking

motion. Too much pressure will

cause the brush to stop rotating.

www.bissell.com 800.237.7691

9

Operations

Tip:

Hair, string and small objects can

block the vacuum hose or tools. Check

them occasionally for obstructions.

CAUTION:

The rotating floor brush continues

to rotate while tools are in use.

To reduce the risk of injury from

moving parts, always move the

cleaner with the carrying handle.

Always place vacuum cleaner on

the floor with handle in upright

position when using tools. Never

place your fingers under the

cleaner when it is running. Never

place powerfoot on furniture or

uneven surfaces. Do not place

vacuum cleaner close enough

to objects to pull them into

rotating brush.

NOTICE:

These tools are designed to

remove pet hair from upholstered

or carpeted surfaces. They should

not be used on pets.

Dusting

Brush/

Upholstery

Tool

Extension

Wand

Crevice Tool

Hose

Base

Pet

TurboBrush

Tool

www.bissell.com 800.237.7691

Operations

10

Quick

Release

Cord

Wrap

1.

Power cord usage

1. To use your vacuum, remove the cord

and plug it into an electrical outlet.

For your convenience, there is a Quick

Release Cord Wrap for easy cord

removal. Instead of unraveling, simply

rotate the cord wrap and slide the cord

off. There is also a cord clip that is part

of the upper cord wrap where you can

attach the cord when vacuuming.

2. When you are finished cleaning, turn

vacuum cleaner off.

3. Unplug power cord by grasping the

polarized plug (NOT the cord) and

disconnect from outlet.

4. Loop power cord around cord wraps on

side of vacuum cleaner. Be sure to first

return the Quick Release Cord Wrap

back to its original position before

wrapping the cord.

5. Clip molded plug to power cord

to secure.

www.bissell.com 800.237.7691

11

Maintenance and care

To maximize your cleaning performance

and extend the life of your vacuum, it

is very important that you empty your

dirt container and check and clean your

filters frequently.

Empty dirt container

The dirt container should to be emptied

before the dirt reaches the “Full” line on

the container.

1. Unplug the vacuum from electrical

outlet.

2. Slide the Lock ‘n Seal Lever to the

“Unlock” position.

3. Grasp handle and pull the dirt

container straight out to remove

from the vacuum.

4. Empty dirt into garbage container.

NOTE: Emptying the dirt

container after every use will

help prevent over filling and

ensure that the vacuum is

ready to go the next time

you clean.

2.

4.

Unlock

Tip:

To maximize cleaning performance,

check and clean or replace all filters

as suggested.

WARNING:

To reduce the risk of electric

shock, turn power switch OFF

and disconnect polarized plug

from electrical outlet before

performing maintenance or

troubleshooting checks.

www.bissell.com 800.237.7691

Maintenance and care

12

1. Unplug the vacuum from electrical outlet.

2. The pre-motor filter protects the motor from

dirt particles. It is located in the slide out

tray underneath the dirt container. Check

the pre-motor filter at least once a month.

If the filter becomes dirty, pull out the tray,

lift out the foam filter pad and clean it.

NOTE: The pre-motor filter may be

hand washed in water with mild

detergent. Rinse well and air dry

thoroughly before replacing.

NOTE: Use of moist parts/compo-

nents in your unit will damage the

motor and void your warranty.

3.

The post-motor filter assists in the filtration

process to return clean air to the room. It is

located behind the door on the side of the

vacuum. If the filter becomes dirty, open the

door, remove the filter and replace.

4. The Febreze® filter is designed to eliminate

odors during the regular life of the filter.

Depending on usage, the post-motor filter

should be changed every 3-6 months.

NOTE: The post-motor filter is a

white, pleated filter. This filter

is not washable and must be

replaced when it becomes dirty.

Check rotating floor brush

and drive belt

You should check your vacuum cleaner’s rotating

floor brush and drive belt regularly for wear or

damage. You should also clean the brush and

brush ends of strings, hair and carpet fibers. This

type of debris can wrap around the brush and

hamper its ability to effectively clean your carpet.

Also remove any debris that has accumulated

under the brush cover.

1. Unplug the vacuum from electrical outlet.

2. Place handle in low position and turn

vacuum cleaner over so bottom side is

facing up.

3. Lift tab 1 and release the three latches in

order 2-4 marked. Lift off the brush cover.

Cleaning the pre-motor filter & replacing the post-motor filter

3.

1

2

3

4

Febreze®

Post-Motor

Filter

Washable

Pre-Motor

Filter

WARNING:

To reduce the risk of injury

from moving parts, turn

vacuum cleaner off and

disconnect power plug from

electrical outlet.

WARNING:

Do not operate cleaner with

damp or wet filters or without

all filters in place.

www.bissell.com 800.237.7691

13

Maintenance and care

Check rotating floor brush

and drive belt (cont)

4. Grasp rotating floor brush at both

ends and lift.

5. Clean strings, hair and other debris

from rotating floor brush, paying

particular attention to brush ends.

6. Clean strings, hair and other debris

from motor pulley and drive belt areas.

7. Check drive belt carefully for wear,

cuts or stressed areas.

8. Check air passageway for obstruc-

tions. Remove debris from this area.

Replace drive belt

1. Unplug the vacuum from electrical outlet.

2. With rotating floor brush removed from

vacuum cleaner (Steps 1-4 of check

rotating floor brush and drive belt),

grasp old drive belt and remove from

motor pulley. Discard the old drive belt.

3. Place new drive belt over motor pulley

and loop other end over rotating floor

brush in the space between the bristles.

NOTE: It is important that

you use only genuine BISSELL

replacement belts. Generic

belts may not meet the exact

specifications required to keep

your vacuum operating at its

peak performance. The use of

unbranded belts could lead to

early failure of the vacuum and

could void your warranty.

4. Pull the rotating floor brush firmly into

position, stretching the drive belt, and

place ends of rotating floor brush

down into the slots on sides as shown.

Alignment of brush ends in slots may

be necessary to fully insert the brush.

5. Turn rotating floor brush by hand several

times in the direction of motor pulley. If

properly installed, drive belt will center

itself on rotating brush crown.

6. Insert front edge of brush cover, rotate

into place, and snap 3 latches.

8.

Motor

Pulley

Air Passageway

3.

Motor

Pulley

www.bissell.com 800.237.7691

Maintenance and care

14

2.

4.

5.

Maintaining Pet TurboBrush

Tool

The Pet TurboBrush Tool should be checked

regularly for clogs or debris wrapping

around the brush.

1. Remove tool from hose or front of vacuum.

2. Twist collar so opening is at the top and

lift top cover to remove.

3. Remove the brush from the belt and

clean debris.

4. Replace the brush inside the belt and

place ends into slots on sides as shown.

5. Reposition top cover making sure to line

up inside tab at the front with the opening

on the cover. Twist collar until opening is

at the bottom to lock into place.

www.bissell.com 800.237.7691

15

Maintenance and care

5.

2.

Clearing clogs

Low suction or poor pickup may be due

to a clog in the vacuum cleaner. If you

notice a change in the sound of the motor,

check for clogs.

1. Unplug the vacuum from electrical outlet.

2. Empty dirt container.

3. Check upper tank for build up or clogs.

4. If you notice a clog in the upper tank,

remove the inner cyclone (see section

"Cleaning the upper tank" on page 16).

5. Grasp the Hose Cuff and separate it

from the Hose Base. Check for a clog in

the base or the hose.

6. Remove the Twist ‘n Snap hose from the

vacuum by turning to the left. Straighten

the hose and unclog with a long,

narrow object such as a broom handle.

7. If the clog persists, follow the instructions

for "Checking the rotating floor brush

and drive belt" on page 12 and inspect

the air passageway for obstructions.

www.bissell.com 800.237.7691

Maintenance and care

www.bissell.com 800.237.7691

16

1.

3.

5.

6.

Cleaning the upper tank

1. Grasp the inner cyclone and twist to

the left until the locking tabs stop the

rotation. Pull down from the upper tank

to remove it.

2. Wipe out the inside of the upper tank

and the inner cyclone with a damp

cloth moistened with water or a mild

cleaning solution.

3. If you desire to thoroughly clean the

filtration disk located in the upper

portion of the inner cyclone, hold the

bottom of the cyclone and turn filtration

disk to the right and pull up to remove.

4. The inner cyclone and filtration disk

may be washed using a mild detergent.

Be sure it is completely dry before

reassembling or damage to your unit

may result.

5. Once cleaning is completed, reassemble

the filtration disk over the inner cyclone

by sliding it straight down on the top

of the inner cyclone and turning left.

Be sure to line up the tabs when

reassembling for proper installation.

6. To replace the inner cyclone, slide it

into the upper housing. Be sure to line

up the inner cyclone by ensuring tabs

on filtration disk are positioned toward

the front of the unit. Push the inner

cyclone in and rotate it to the right

until the locking tabs stop the rotation.

www.bissell.com 800.237.7691

17

Troubleshooting

Vacuum cleaner won’t run

Possible causes Remedies

1. Power cord not plugged in 1. Check electrical plug

2. Blown fuse/tripped breaker in home 2. Check/replace fuse or reset breaker

3. Damaged power cord 3. Unplug, check for damage, replace

as necessary

Vacuum cleaner and tools won’t pick up dirt

Possible causes Remedies

1. Incorrect height adjustment 1. Adjust powerfoot to correct height

2. Hose not attached to suction opening 2. Firmly push hose wand into hose

wand base

3. Twist 'n Snap hose not securely attached 3. Make sure Twist 'n Snap hose is snapped

into locked position

4. Crack or hole in hose 4. Check hose and replace if needed

5. Broken or worn drive belt 5. Replace drive belt, see page 13

6. Rotating floor brush bristles worn 6. Replace brush

7. Rotating floor brush jammed 7. Remove brush and clean debris from

brush ends

8. Clog in vacuum 8. Clear clogs, see page 15

9. Dirt container full 9. Empty dirt container

10. Dirt container not installed properly 10. Position correctly and lock in place

11. Filters are dirty 11. Check pre-motor and post-motor filters

12. Pet TurboBrush Tool is clogged or debris is wrapped 12. See page 14 for Maintaining Pet TurboBrush Tool

Vacuum cleaner is difficult to push

Possible causes Remedies

1. Incorrect height setting 1. Adjust powerfoot to correct height setting

Visible dirt escaping from cleaner

Possible causes Remedies

1. Dirt container full 1. Empty dirt container

2. Filters missing or installed incorrectly 2. Check pre-motor and post-motor filters for

correct installation

3. Dirt container installed incorrectly 3. Pull out and re-insert dirt container correctly

Other maintenance or service not included in the manual should be

performed by an authorized service representative.

Thank you for selecting a BISSELL product.

Please do not return this product to the store.

For any questions or concerns, BISSELL is happy to be of service.

Contact us directly at 1-800-237-7691.

WARNING:

To reduce the risk of electric shock, turn

power OFF and disconnect polarized plug

from electrical outlet before performing

maintenance or troubleshooting.

www.bissell.com 800.237.7691

Replacement Parts

Accessories

18

Item Part No. Part Name

1 32074 Style 7/9/10/12/14 Drive Belt (2-Pack)

2 203-1283 Brush Roll

3 203-1073 Style 7/8/14 Pre-Motor Foam Filter

4 3091 Style 8/14 Post-Motor HEPA Media Filter*

5 99K1 Febreze

®

Style 8 & 14 Post-Motor Filter

1 2

3 4

5

6

These items are available for purchase as accessories for your BISSELL PowerGlide Pet

®

:

To purchase call 1-800-237-7691 or visit www.bissell.com.

Item Part No. Part Name

1 203-1056 Crevice Tool

2 203-1059 Dusting Brush/Upholstery Tool

3 203-1290 Pet TurboBrush Tool

4 203-1291 Pet Contour Tool

5 203-1068 Extension Wand

6 203-8049 Hose Assembly

*The filter media, not the vacuum as a whole, complies with IEST-RP-CC001.5 HEPA standard.

1 2 3 4/5

www.bissell.com 800.237.7691

19

Warranty

This warranty gives you specific legal rights, and you may also have other rights which

may vary from state to state. If you need additional instruction regarding this warranty

or have questions regarding what it may cover, please contact BISSELL Consumer Care

by E-mail, telephone, or regular mail as described below.

Limited Three Year Warranty

Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product

BISSELL will repair or replace (with new or remanufactured components or products), at BISSELL’s

option, free of charge from the date of purchase by the original purchaser, for three years any

defective or malfunctioning part.

See information below on "If your BISSELL product should require service".

This warranty applies to product used for personal, and not commercial or rental service. This

warranty does not apply to fans or routine maintenance components such as filters, belts, or

brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair,

or any other use not in accordance with the User's Guide is not covered.

If your BISSELL product should require service:

Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area.

If you need information about repairs or replacement parts, or if you have questions

about your warranty, contact BISSELL Consumer Care.

Website or E-mail:

www.bissell.com

Or Call:

BISSELL Consumer Care

1-800-237-7691

Monday - Friday 8 am - 10 pm ET

Saturday 9 am - 8 pm ET

Or Write:

BISSELL Homecare, Inc.

PO Box 3606

Grand Rapids, MI 49501

ATTN: Consumer Care

BISSELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE

ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELL’S LIABILITY WILL NOT EXCEED THE

PURCHASE PRICE OF THE PRODUCT.

Some states do not allow the exclusion or limitation of incidental or consequential

damages, so the above limitation or exclusion may not apply to you.

*EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY

THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL

OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW,

INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO THE THREE YEAR DURATION FROM THE DATE OF

PURCHASE AS DESCRIBED ABOVE.

Some states do not allow limitations on how long an implied warranty last so the above limitation

may not apply to you.

NOTE: Please keep your original sales receipt. It provides proof of date of purchase

in the event of a warranty claim.

Grand Rapids, Michigan

Part Number 110-4535

Rev 4/12

Visit our website at:

www.bissell.com

For information about repairs or replacement parts, or questions about your warranty, call:

BISSELL Consumer Care

1-800-237-7691

Monday – Friday 8 am - 10 pm ET

Saturday 9 am - 8 pm ET

Or write:

BISSELL Homecare, Inc.

PO Box 3606

Grand Rapids MI 49501

ATTN: Consumer Care

Or visit the BISSELL website - www.bissell.com

When contacting BISSELL, have model number of cleaner available.

Please record your Model Number: ___________________

Please record your Purchase Date: ___________________

NOTE: Please keep your original sales receipt. It

provides proof of purchase date in the event of a

warranty claim. See Warranty on page 19 for details.

BISSELL consumer care

www.bissell.com 800.237.7691

20

Registering is quick, easy and offers you benefits over the lifetime of your product.

You’ll receive:

BISSELL Rewards Points

Automatically earn points for discounts and free shipping on future purchases.

Faster Service

Supplying your information now saves you time should you need to contact us with

questions regarding your product.

Product Support Reminders and Alerts

We’ll contact you with any important product maintenance reminders and alerts.

Special Promotions

Optional: Register your email to receive notice of offers, contests, cleaning tips and more!

Visit www.bissell.com/registration now!

Don't forget to register your product!

La page charge ...

Bissell PowerGlide Pet 1044 SERIES Manuel utilisateur

Ce manuel convient également à

Bissell PowerGlide Pet 1044 SERIES Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents