Primo 200 Le manuel du propriétaire

Marque: Primo

Modèle: 200

Catégorie: Barbecues

Taper: Le manuel du propriétaire

Ce manuel convient également à

PCG.rev04282017- 10:53

WARNING:

Improper installation, adjustment, alteration,

service, or maintenance can cause injury or

property damage. For proper installation, refer

to the installation instructions. For assistance

or additional information, consult a quali ed

professional service technician, service agency,

or the gas supplier.

WARNING:

1. Do not store or use gasoline or other

 ammable vapors and liquids in the vicinity

of this or any other appliance.

2. An LP cylinder not connected for use shall

not be stored in the vicinity of this or any

other appliance.

INSTALLER: Leave these instructions with the consumer.

CONSUMER: Retain for future reference

IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE.

WARNING

GAS SERIES

DANGER:

IF YOU SMELL GAS:

1. Shut off the gas to the appliance.

2. Extinguish any open  ame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your gas

supplier or the  re department.

CODE AND SUPPLY REQUIREMENTS: This

grill must be installed in accordance with local

codes and ordinances, or, in the absence of local

codes, with the latest National Fuel Gas Code

(ANSI Z223.1/NFPA 54), or Natural Gas and

Propane Storage and Handling Installation Code

(CSA-B149.1).

This appliance and its dedicated manual shutoff

valve must be disconnected from the gas-

supply piping system when testing the system at

pressures in excess of 1⁄2 psig (3.5 kPa).

This appliance must be isolated from the gas-

supply piping system by closing its dedicated

manual shutoff valve during any pressure testing

of the gas-supply system at pressures up to and

including 1⁄2 psig (3.5 kPa).

Proper operation of your grill requires prompt

and periodic maintenance. See the CARE &

CLEANING section for details.

Keep all electrical-supply cords and fuel-supply

hoses away from any heated surface.

WARNINGS AND SAFETY CODES

OUTDOOR GAS GRILL

INSTALLATION INSTRUCTIONS

AND OWNER’S MANUAL

MODEL# G420C (Freestanding) G420H (Head only)

PCG.rev04282017- 10:53

INSTALLATION INSTRUCTIONS ET MANUEL DU PROPRIÉTAIRE

PRIMO GRIL EXTÉRIEUR DE GAZ DU PORTATIF

AVERTISSEMENT:

L’installation inexacte, l’ajustement, le

changement, le service, ou l’entretien peuvent

causer des dommages ou des dégats matériels.

Référez-vous à ce manuel. Pour de l’aide

ou des renseignements supplémentaires,

consultez un technicien professionnel qualié

de service, une agence de service ou le

fournisseur de gaz.

AVERTISSEMENT:

1. Ne stockez pas ou n’employez pas l’essence

ou d’autres vapeurs et liquides inammables

à proximité de ceci ou d’aucun autre

appareil.

2. Un cylindre de propane non relié pour

l’usage ne sera pas stocké à proximité de

ceci ou d’aucun autre appareil.

IMPORTANT: LISEZ CES INSTRUCTIONS SOIGNEUSEMENT AVANT DE COMMENCER OU L’INSTALLATION L’UTILISATION

AVERTISSEMENT

DANGER:

SI VOUS SENTEZ LE GAZ :

1. Coupezl’admissiondegazdeI’appariel.

2. Éteindre toute amme nue.

3. Ouvrir le couvercle.

4. Si l’odeur persiste, éloignez-vous de

l’appareil et appelez immédiatement le

fournisseur de gaz ou le service d’incendie.

CONDITIONS DE CODE ET D’APPROVISIONNEMENT:

Ce gril doit être installé selon des codes et des ordonnances

locaux, ou, en l’absence des codes locaux, avec l’un ou

l’autre le plus défunt Code national de gaz de carburant

(norme ANSI Z223.1/NFPA 54), et Stockage de gaz naturel

et de propane et manipulation du code d’installation

(CSA-B149.1).

Cet appareil et ses différents robinets d’isolement doivent être

démontés du gaz-fournissent le système sifant en examinant

le système aux pressions au-dessus du 1⁄2 psig (kPa 3.5).

Cet appareil doit être isolé dans gaz-fournissent le système

sifant par fermeture que ses différents robinets d’isolement

manuels pendant tous les essais sous pression du gaz-

fournissent le système aux pressions jusques et y compris le

1⁄2 psig (kPa 3.5).

• Ce gril est pour ultilisation à l’extérieur seulement. Si

l’appareil est entreposé à l’intérieur, enlever les bouteilles

et les laisser à l’extérieur.

• Ne pas ranger le gril immédiatement aprés l’avoir utilisé.

le laisser refroidir avant de le déplacer ou de la ranger.

Le non respect de cette mesure de sécurité pourrait

entraîner un incendie causant des dommages à la

propriété, des blessures ou la mort.

• Ne pas utiliser cet appareil sous une surface combustible.

• Ne pas utiliser cet appareil sous un auvent. Le non

respect de cette mesure de sécurité pourrait entraîner un

incendie ou des blessures.

• Dégagement minimal entre les parois latérales et l’arriére

de l’appareil et la construction combustible (45.7 cm à

partir des parois latérales et 45.7cm à partir de l’arriére).

• Le régulareur de pression de gaz prévu avec cet appareil

de cuisson à gaz pour l’extérieur doit être utilisé. Ce

régulateur est réglé pour une pression de sortie de 5

pouces de colonne de l’eau pour le gaz naturel, et 10

pouces pour le propane.

• LE RÉGULATEUR INCLUS D’APPAREILS EST ÉVALUÉ

POUR LE MAXIMUM DE 1/2 (LIVRES PAR POUCE

CARRÉ). SI VOTRE OFFRE DE GAZ EST 1/2 PLUS

GRAND QUE (LIVRES PAR POUCE CARRÉ), UN

RÉGULATEUR ADDITIONNEL DOIT ÊTRE INSTALLÉ

Maintenez tout électrique-fournissent des cordes et

carburant- fournissent des tuyaux partis de n’importe quelle

surface de chauffage.

AVANT LE GRIL. VOIR LA SECTION DE CONDITIONS

D’OFFRE DE GAZ POUR LA PRESSION APPROPRIÉE

D’OFFRE DE GAZ.

• Ne couvrez jamais la surface entière de cuisine ou de

gril de gauffreuses ou de casseroles. La surchauffe se

produira et les brûleurs ne seront pas très performants

quand la chaleur de combustion est emprisonnée au-

dessous de la surface à cuire.

• Ne pulvérisez jamais l’eau sur une unité chaude de gaz,

comme ceci peut endommager des composants de

porcelaine ou de fer de fonte.

• Une fuite de GPL peut causer une incendie ou une

explosion si enammée entraînant des blessures

corporelles graves ou la mort.

• Communiquez avec le fournisseur de GPL pour les

réparations ou pour disposer de qules bouteille ou du

GPL non utilisé.

SÛRETÉ ET CODES D’AVERTISSEMENT

INSTALLATEUR : Laissez ces instructions avec le consommateur.

CONSOMMATEUR : Maintenez pour la future référence.

PCG.rev04282017- 10:53

Getting Started

MODEL SPECIFICATIONS ........................................................................................................1

HEAD UNIT ONLY CUTOUT SPECIFICATIONS ....................................................................... 2

ENCLOSURE REQUIREMENTS ...............................................................................................3

REPLACEMENT PARTS ............................................................................................................ 4

GRILL MAINTENANCE & SAFETY ............................................................................................ 5

INSTALLATION REQUIREMENTS ............................................................................................6

PROPANE SAFETY INFORMATION ......................................................................................... 9

SAFE USE AND MAINTENANCE OF PROPANE GAS CYLINDERS ...................................... 10

Installation

INSTALLATION ........................................................................................................................12

LOCATION PREPARATION ..................................................................................................... 12

WHEELS AND CASTERS ........................................................................................................12

CONNECT THE GAS SUPPLY ................................................................................................12

INSTALL THE IGNITER BATTERY ..........................................................................................13

USING THE FOLDING SHELVES ............................................................................................13

BURNER SPECIFICATIONS AND INSTALLATION ORIENTATION ....................................... 17

Use, Care & Maintenance

IDENTIFICATION OF GRILL CONTROLS ............................................................................... 13

LIGHTING/IGNITION INSTRUCTIONS ....................................................................................14

CONVERT GAS TYPE & CHECK BURNER ORIFICES .......................................................... 16

CONTROL PANEL REMOVAL ................................................................................................. 18

TROUBLESHOOTING .............................................................................................................19

CARE & CLEANING .................................................................................................................20

WARRANTY .............................................................................................................................21

TABLE OF CONTENTS

PCG.rev04282017- 10:53

Main (High Burner)

N/P ori ce drill size

LP #66 / NAT #56

NOTE:

G420C (Freestanding) ships with

propane ori ce installed. G420H

(Head only) ships with natural gas

ori ce installed.

Seconadary (Low Burner)

N/P ori ce drill size

LP #76 / NAT #70

DIMENSIONS

Model Height Width Depth

G420C

Floor to Top of Grill

Floor to

top of

shelf

(C)

Cart Base

(D)

With shelves Front to back

Open

(A)

Closed

(B)

(E)

1 up &

1 down

(F)

Cart Base

(G)

Maximum outer

(H)

60" 46" 34" 36" 60-1/2" 53-1/2" 26" 29"

G420H

Base of shroud to

Top of Grill

Shroud

height

(C)

Shroud Width

(E)

Maximum outer

(H)

Open

(A)

Closed

(B)

37" 23" 11" 36-1/4" 29"

** 5" from back of unit wall clearance required to open lid **

MODEL SPECIFICATIONS

G420H HEAD UNIT ONLY

PCG.rev04282017- 10:53

G420H HEAD UNIT ONLY CUTOUT AND INSTALLATION

4-1/4” of open space behind grill

23-1/4”

27-1/2”

36 1/2”

11”

4-1/4” of open space behind grill

23-1/4”

27-1/2”

36 1/2”

11”

Top View

NOTE: 4-1/4” open space behind grill shroud is required for hinge clearance.

NOTE: 10" of clearance from back of hinge required to open lid.

NOTE: The control panel is designed to protrude past the front of the

countertop surface. (g. 1)

IMPORTANT: The G420H is a slide-in installation, not a hanging

installation. The base of the metal grill surround must be supported from the

bottom edges.

Front View

g. 1

* Note: If installing this grill in a combustible enclosure, the correct insulating liner must be used.

Consult liner instructions for counter cut-out dimensions and installation.

PCG.rev04282017- 10:53

ENCLOSURE REQUIREMENTS

VENTILATION (ALL ENCLOSURES)

For All Piping Systems and All Gas Types: (Natural

Gas, Household Propane, L.P. Cylinder)

FOR YOUR SAFETY, you must provide the openings

listed below for replacement air and cross-ventilation

of the unit enclosure.

One side of the enclosure shall be left completely

open to the outside; OR 4 (minimum) ventilation

openings MUST be created (reference Fig. 1):

Each opening must have a minimum of 10 sq. in. of

free area. The openings must be equally sized and

unobstructed.

Two openings must be in the side walls of the enclosure,

at the top level, and spaced at 180 degrees. The openings

must begin 1" or less below the countertop level and end

no more than 5" below the countertop level.

Two openings must be in the side walls of the enclosure,

at the oor level, and spaced at 180 degrees.The openings

must begin 1" or less above the oor level and end no

more than 5" above the oor level.

To achieve the proper ventilation, you may use venting

panels as shown. Contact your dealer.

KEEP THE VENT OPENINGS AND SURROUNDING

AREA OF THE ENCLOSURE CLEAN AND FREE OF

OBSTRUCTIONS AT ALL TIMES.

WARNING: Ventilation openings in side walls shall not

communicate directly with other enclosures of the outdoor

cooking gas appliance.

WHEN A PROPANE (L.P.) CYLINDER IS USED IN THE

ENCLOSURE

When a propane (L.P.) cylinder is installed inside of the

enclosure, the guidelines below MUST be followed.

FAILURE TO DO SO MAY CAUSE DAMAGE TO YOUR

UNIT AND/OR PERSONAL INJURY. Reference Fig. 2 for

an example.

• A non-combustible heatshield must be installed to

protect the regulator/hose assembly and propane

cylinder valve.

• Many dealers offer propane tank door with tank tray

models and a propane tank heatshield that rests

directly on the tank to meet the cylinder install

requirements. Propane tank door with tank tray

shown in Fig. 3. Contact your dealer for ordering

information.

Surrounding area and vent openings

must be clear for proper venting.

Ventilation Requirements

• 4 openings minium with 2 per side wall, spaced at 180º.

• Top openings within 5” of countertop

• Bottom openings withing 5” of floor.

1” min

5” max

4 total vent openings at

10 sq. in. of free area

minimum each

1” min

5” max

Fig. 1 Ventilation detail

L.P. Cylinder

Non-combustible

heat shield

Regulator/hose

assembly

Fig. 2 Propane cyilnder orientaion

L.P. Cylinder

Cylinder and regulator/hose assembly

protected by heat shield

Fig. 3 Optional door with propane tank tray

PCG.rev04282017- 10:53

REPLACEMENT PARTS

PART NUMBER PART DESCRIPTION QTY HEAD CART

0142001 CERAMIC BOTTOM 1 • •

0142002 CERAMIC TOP 1 • •

0142003 INTERNAL STAINLESS STEEL BASKET 1 • •

0142004 STAINLESS STEEL FLAVOR GRATE 2 • •

0142005 STAINLESS STEEL COOKING GRATES 2 • •

0142006 STAINLESS STEEL HANDLE 1 • •

0142007 CONVERTER KIT FOR ORIFICES 1 • •

0142008 METAL FRAME WITH DOORS 1 •

0142009 UPPER METAL FRAME 1 • •

0142010 STAINLESS STEEL FRONT PANNEL 1 • •

0142011 INSIDE STAINLESS STEEL SIDE TABLES 2 • •

0142012 STAINLESS STEEL DRIP PAN TRAY 1 • •

0142013 STAINLESS STEEL FOLD DOWN SIDE TABLES 2 •

0142014 STAINLESS STEEL HINGE MECHANISM 1 • •

0142015 KNOBS FOR GAS VALVE 4 • •

0142016 NAME PLATE 1 • •

0142017 GAS VALVES 4 • •

0142018 ELECTRONIC IGNITOR KNOB 1 • •

0142019 CERAMIC ELECTRODES 2 • •

0142020 GAS PILOT TUNNEL BOX 2 • •

0142021 HOSE FOR NATURAL GAS WITH QUICK DISC 1 •

0142022 GAS MANIFOLD 1 • •

0142023 PROPANE HOSE WITH REGULATOR 1 •

0142024 SHORT STEEM THERMOMETER WITH SLEEVE 1 • •

0142030 MANUAL 1 • •

0142032 LOW HEAT BURNERS 2 • •

0142033 HIGH HEAT BURNERS 2 • •

0142034 V-SHAPED SMOKER BOX 1 • •

PCG.rev04282017- 10:53

GRILL MAINTENANCE & SAFETY

1. The outdoor grill and surrounding area MUST

remain clear of ammable substances such

as gasoline, yard debris, wood, etc.

2. The airow through the vent space located

below the control panel must remain

unobstructed.

3. When using propane gas:

a. The required ventilation openings in the

enclosure must be clear of debris. See the

PROPANE SAFETY INFORMATION section.

b. The propane cylinder, regulator, and rubber

hose must be in a location not subject to

temperature above 125° F (51° C).

4. The ames on each burner burn evenly along

the entire burner with a steady ame (mostly

blue). If burner ames are not normal, check

and clean the orice and burner/venturi tubes

for insects and insect nests. A clogged tube

can lead to a re beneath the grill. A proper

ame pattern will ensure safe operation and

optimal performance.

5. The in-line gas valve or gas cylinder valve

must always be shut OFF when the grill is not

in use.

6. The drip collector holes must be clear and

unobstructed. Excessive grease deposits can

result in a grease re.

7. Whenever reconnecting any wires, apply a

small amount of dielectric grease to the male

connector, then make the connection. This

will ensure conductivity and prevent moisture

from affecting the contact.

IMPORTANT

IN THE EVENT OF A GREASE FIRE, IMMEDIATELY SHUT OFF THE MAIN GAS VALVE TO THE

UNIT. KEEP THE LID OPEN AND ALLOW THE FIRE TO EXTINGUISH ITSELF. A THOROUGH

INSPECTION BY A TRAINED SERVICE TECHNICIAN SHOULD BE CONDUCTED BEFORE

FUTURE USE OF YOUR UNIT. THE SERVICE TECHNICIAN WILL CHECK THE SYSTEM FOR

GAS LEAKS AND WILL CHECK ALL ELECTRICAL WIRING FOR DAMAGE. ALL GAS LEAKS

AND WIRING MUST BE REPAIRED PRIOR TO FUTURE USE.

WARNING: NEVER cover the entire cooking or grill surface with griddles or pans.

Overheating will occur, and burners will not perform properly when combustion heat is

trapped below the cooking surface.

CAUTION: NEVER spray water on a hot gas unit.

PCG.rev04282017- 10:53

INSTALLATION REQUIREMENTS

Installation must be performed by a qualied

professional service technician.

This grill is designed for outdoor use only. DO

NOT use this grill inside a building, garage, or

enclosed area. DO NOT use this grill in or on a

recreational vehicle or boat.

When installing this grill in a combustible

surround, an insulating liner must be used.

The grill must have a minimum clearance of 18”

from combustible materials/items in all directions.

OVERHEAD CONSTRUCTION AND EXHAUST

HOOD REQUIREMENTS

A minimum of 5 foot clearance is required

between the counter top and the overhead

construction.

When installed under combustible overhead

construction, the area above the cooking surface

of the grill must be covered with an exhaust

hood. The exhaust hood provides the protection

for the combustible overhead construction. See

exhaust hood information below and Figure A.

Important: DO NOT use this appliance under

unprotected combustible overhead construction.

When installed under overhead non-combustible

construction, an exhaust hood is highly

recommended; see exhaust hood information

below and Figure A.

Exhaust Hood

When using an exhaust hood, the area above the

cooking surface of the grill must be covered with

a hood larger than the cooking area of the grill,

and with a minimum of 1200 CFM (cubic feet per

minute) for proper outdoor application.

*Combustible overhead construction:

Exhaust hood required

Non-combustible overhead construction:

Exhaust hood highly recommended

Non-Combustible Wall

**Overhead Construction**

Exhaust Hood

5’ Minimum

Figure A. Overhead construction requirements.

PCG.rev04282017- 10:53

INSTALLATION REQUIREMENTS

SIDE AND REAR WALL CLEARANCES

NOTE:

10" from back of hinge required to open lid.

For the minimum clearances between the grill

and any side or rear walls, your setup must fall

within one (or more) of the following:

A. Clearance between grill and strictly non-

combustible wall

(i.e. brick wall, see Figure 1)

• The grill must have a minimum of 4" right, left,

and rear clearance from any non-combustible

wall.

(To allow for proper ventilation and prevent

dangerous overheating.)

B. Clearance between grill and a protected

combustible wall

(i.e. a non-combustible wall in front of a

combustible wall to serve as a barrier. This

can be accomplished by brick, or a metal stud

nished with non-combustible substrate, see

Figure 2)

• The grill must have a minimum of 14" right,

left, and rear clearance from the protected

combustible wall.

(The 4" non-combustible material plus an

additional X" clearance between the grill and

protected wall.)

C. Clearance between grill and combustible

wall

• The grill must have a minimum of 18" right, left,

and rear clearance from any combustible wall

(see Figure 3).

BACKSPLASH CLEARANCE (IF APPLICABLE)

If a non-combustible backsplash exists, it must

have a minimum of a 5” clearance from the

rear of the grill (to allow for hinge clearance,

proper ventilation and to prevent dangerous

overheating). See Fig. 4.

Non-Combustible Wall

4”

Figure 1 Clearance ‘A’ Diagram

Non-Combustible 4”

Combustible

Non-Combustible Substrate

14”

Figure 2 Clearance ‘B’ Diagram

Combustible

18”

Figure 3 Clearance ‘C’ Diagram

4-1/4” of open space behind grill

23-1/4”

27-1/2”

36 1/2”

11”

Figure 4 Backsplash Clearance Diagram

PCG.rev04282017- 10:53

INSTALLATION REQUIREMENTS

The control panel MUST remain removable for servicing (see PARTS LIST).

ENSURE PROPER COMBUSTION AIR AND COOLING AIRFLOW

Proper airow MUST be maintained for the grill to perform as it was designed. If airow is blocked,

overheating and poor combustion will result. Do not block air inlet along the bottom of the control

panel or more than 75% of the cooking grid surface with pans or griddles.

Note: The 1” (2.5 cm) front air space also allows access to the drip tray.

GAS-SUPPLY PLUMBING REQUIREMENTS

For natural gas or a household propane system, rigid 1/2” (1.3 cm) or 3/4” (1.9 cm) black steel pipe

or local code-approved pipe is required to conduct the gas supply to the unit. Contact your local gas

supplier. Connect this pipe to the required C.S.A.-approved stainless-steel ex connector (attached).

An NPT adapter has been provided for 1/2” pipe. DO NOT use a rubber hose within the grill

enclosure. Apply only joint compounds that are resistant to all gasses to all male pipe ttings except

are ttings. Make sure to tighten every joint securely.

Note: If 1/2” (1.3 cm) pipe is used with natural gas, it should be no longer than 20’ (6.1 meters).

Important: A shut-off valve (not included) in the gas line is required. It provides for safety when

the unit is not in use and for convenient maintenance and repair. It must be installed within 6 feet of

the unit. Use a pipe joint compound resistant to all gasses on all male ttings except are ttings.

GAS SUPPLY AND MANIFOLD PRESSURES:

For natural gas - normal 7” (17.78 cm) water column (w.c.), minimum 5” (12.7 cm), maximum 10 1/2”

(26.7 cm). For propane gas - normal 11” w.c., minimum 10” (25.4 cm), maximum 13” (33 cm).

PCG.rev04282017- 10:53

PROPANE SAFETY INFORMATION

WARNING

THIS APPLIANCE MUST BE INSTALLED

AND OPERATED ACCORDING TO THE

INFORMATION BELOW.

FAILURE TO PROPERLY VENT THE CABINET

MAY RESULT IN A FIRE OR EXPLOSION

CAUSING SERIOUS INJURY OR DEATH.

When using propane gas:

• Propane Gas (also known as L.P. Gas) is

heavier than air and will accumulate or pool in

an inadequately vented enclosure or recessed

area.

• A leaking gas connection or valve

unintentionally left open will create a hazard.

• If a pool of propane gas is ignited, an

explosion will occur. Adequate venting at

the oor level of the cabinet eliminates this

danger.

• DO NOT store a spare propane-gas cylinder

in or near the unit.

INSTALLATION SAFETY GUIDELINES

THIS UNIT MUST BE INSTALLED IN SUCH A

MANNER THAT ALL VENT OPENINGS ON THE

CABINET REMAIN CLEAR AND FREE OF ALL

OBSTRUCTIONS AT ALL TIMES AND DURING

ALL WEATHER CONDITIONS.

The gas cylinder, regulator, and rubber hose

must be in a location not subject to temps

above 125° F (51° C).

WHEN A PROPANE CYLINDER IS INSTALLED

INSIDE OF THE CABINET, THE GUIDELINES

FOUND IN THE SAFE USE & MAINTENANCE

OF PROPANE GAS CYLINDERS SECTION

MUST BE FOLLOWED.

OPERATING THE UNIT SAFELY AND

CORRECTLY

Every time you use the unit, make sure that:

1. The area around the unit is clear and free

from combustible materials, gasoline and

ammable vapors/liquids.

2. There is no blockage of the airow through

the vent openings located on the cabinet.

3. The hose is inspected (if applicable).See

SAFE USE & MAINTENANCE OF PROPANE

GAS CYLINDERS section.

DO NOT store any combustible materials,

gasoline, and any other ammable vapors/

liquids in the vicinity of the unit. Provide adequate

clearance for servicing and operation.

WHEN OPERATING THIS APPLIANCE WITH PROPANE, ALL INSTRUCTIONS AND WARNINGS

MUST BE OBSERVED. FAILURE TO DO SO MAY RESULT IN A FIRE OR EXPLOSION

CAUSING SERIOUS INJURY OR DEATH.

PCG.rev04282017- 10:53

SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS

CYLINDER/CONNECTOR REQUIREMENTS

1. Propane-gas cylinders, valves, and hoses must be

maintained in good condition and must be replaced if

there is visible damage to either the cylinder or valve. If

the hose is cut or shows excessive abrasion or wear, it

must be replaced before using the gas appliance (see

3.).

2. This unit, when used with a cylinder, should be

connected to a standard 5-gallon (15 lb.) propane-gas

cylinder equipped with an OPD (Overll Prevention

Device). The OPD has been required on all cylinders

sold since October 1,1998, to prevent overlling.

3. Cylinder dimensions should be approximately 12” (30.5

cm) in diameter and 18” (45.7 cm) high. Cylinders must

be constructed and marked in accordance with the

Specications for Propane Gas Cylinders of the U.S.

Department of Transportation (D.O.T.) or the National

Standard of Canada, CAN/CSA-B339, Cylinders,

Spheres, and Tubes for Transportation of Dangerous

Goods.

4. The cylinder used must include a collar to protect the

cylinder valve, and the cylinder supply system must be

arranged for vapor withdrawal.

5. The pressure regulator and hose assembly (Figure

1) supplied with this outdoor gas appliance (L.P.

models only) must be used. Original and replacement

pressure regulator and hose assemblies must be those

specied by the manufacturer for connection with a

cylinder connecting device identied as Type I by the

ANSI Z 21.58/CGA 1.6 (see PARTS LIST for ordering

information).

6. The propane-gas cylinder valve must be equipped with

a cylinder connection coupling device, described as

Type I in the standard dened in paragraph 5. above.

This device is commonly described as an Acme thread

quick coupler.

7. If the propane-gas cylinder comes with a dust plug,

place the dust cap on the cylinder valve outlet

whenever the cylinder is not in use.

QUICK COUPLER OPERATION

To connect the regulator/hose assembly to the

propane-gas cylinder valve tting: Press the hand nut

on the regulator over the Acme thread tting on the cylinder

IMPORTANT FOR YOUR SAFETY

READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.

When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST

be observed. FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION.

SECURING THE PROPANE GAS CYLINDER

• Insert propane tank into hole in cabinet base (Fig. 1-A).

• Raise bracket over lip of propane tank and tighten thumbscrew (Fig 1-B).

• Follow instructions above to connect supply.

valve. Turn the hand nut clockwise to engage the threads

and tighten until snug. The use of pliers or a wrench should

not be necessary. Only cylinders marked “propane” may be

used.

To disconnect: Turn the hand nut counterclockwise until

detached (Figure 1).

Important: Before using the unit, and after each time the

cylinder is removed and reattached, check the hose for

wear (see 1.) and check all connections for leaks. Turn

off the unit valves and open the main cylinder valve, then

check connections with soapy water. Repair any leaks

before lighting the unit.

CAUTION: Always turn the propane cylinder main valve off

after each use, and before moving the unit and cylinder or

disconnecting the coupling. This valve must remain closed

and the cylinder disconnected while the appliance is not

in use, even though the gas ow is stopped by a safety

feature when the coupler is disconnected.

Carefully inspect the hose assembly each time before

the gas is turned on. A cracked or frayed hose must be

replaced immediately.

If the appliance is stored indoors, the cylinder must be

disconnected and removed. Disconnected cylinders must

be stored outdoors, out of the reach of children, with

threaded valve plugs tightly installed, and must not be

stored in a building, garage, or any other enclosed area.

FOR YOUR SAFETY

a. DO NOT store a spare propane-gas cylinder under or

near this appliance.

b. NEVER ll the cylinder beyond 80-percent full.

c. IF THE INFORMATION IN A. AND B. IS NOT

FOLLOWED EXACTLY, A FIRE CAUSING DEATH OR

SERIOUS INJURY MAY OCCUR.

QCC

Typ e 1

Valve

Pressure

Relief

Valve

Hand Wheel

Acme Thread

Brass Fitting

Regulator

Vent

Hose

Acme Thread

Hand Nut

Liquid Level

Indicator

(optional)

(Figure 1) Type I Acme Quick Coupler

1-A 1-B

PCG.rev04282017- 10:53

FIXATION DU CYLINDRE DE GAZ DE PROPANE

• Insérez le réservoir de propane dans le trou de la base du meuble (Fig. 1-A).

• Soulever le support sur la lèvre du réservoir de propane et serrer la vis à oreilles (Fig 1-B).

• Suivez les instructions ci-dessus pour connecter l’alimentation.

UTILISATION SÛRE ET ENTRETIEN DES CYLINDRES DE GAZ DE PROPANE

CYLINDRE ET CONDITIONS ET CARACTÉRISTIQUES

DE CONNECTEUR

1. Des cylindres et les valves de gaz de propane doivent

être maintenus en bon état et doivent être remplacés

s’il y a des dommages évidents au cylindre ou à la

valve.

2. Ce gril, une fois utilisé avec un cylindre, devrait être

relié à un gallon de la norme 5 (15lb.) cylindre de gaz

de propane équipé d’un OPD (remplissez au-dessus

du niveau le dispositif d’empêchement). L’OPD a été

exigé sur tous les cylindres vendus depuis octobre

1.1998 pour empêcher le remplissage excessif.

3. Les dimensions de cylindre devraient être

approximativement 12”(30.5cm) de diamètre et 18”

(45.7cm) hauts. Des cylindres doivent être construits et

marqués selon les caractéristiques pour des cylindres

de gaz de propane du département des ETATS-UNIS

du transport (D.O.T.) ou le niveau national du Canada,

du CAN/CSA-B339, des cylindres, des sphères

et des tubes pour le transport des marchandises

dangereuses.

4. Le cylindre doit inclure un collier pour protéger la valve

de cylindre et le circuit d’alimentation de cylindre doit

être assuré le retrait de vapeur.

5. Le montage du régulateur de pression et le exible

(Fig. 1) fourni avec cet appareil au gaz en plein air

(modèles au propane seulement) doit être utilisé.

Assemblées d’origine et régulateur de pression et le

tuyau de remplacement doivent être ceux spéciés

par le fabricant pour le raccordement d’un dispositif de

cylindre de liaison identiée comme de type I par le

ANSI Z 21.58/CGA 1.6 (voir liste des pièces pour les

informations de commande).

6. La valve de cylindre de gaz de propane doit

être équipée d’un dispositif d’accouplement de

raccordement de cylindre, décrit comme type I dans

la norme dénie dans le e. de paragraphe ci-dessus.

Ce dispositif est généralement décrit comme coupleur

rapide de l de point culminant.

7. Si votre cylindre de gaz de propane vient avec une

prisede la poussière, placez le bouchon anti-poussière

sur la sortie de valve de cylindre toutes les fois que le

cylindre n’est pas en service.

OPÉRATION DE COUPLEUR RAPIDE

Pour relier le regulator/hose à l’ajustage de précision

de valve de cylindre de gaz de propane: Serrez l’écrou

de main sur le régulateur au-dessus de l’ajustage de

précision de l de point culminant sur la valve de cylindre.

Tournez l’écrou de main dans le sens des aiguilles d’une

montre pour engager les ls et pour serrer jusqu’à ce que

douillettement. L’utilisation des pinces ou de la clé ne

devrait pas être nécessaire. Seulement le propane marqué

par cylindres doit être employé.

Pour débrancher: Tournez l’écrou de main dans le sens

contraire des aiguilles d’une montre jusqu’à isolé (g. 1).

Important: Avant d’employer le gril, et ensuite chaque fois

que le cylindre est enlevé et rattaché, examinez tous les

raccordements pour déceler les fuites. Arrêtez les valves

de gril et ouvrez la valve principale de cylindre, puis vériez

les raccordements avec de l’eau savonneux. Réparez

toutes les fuites avant d’allumer le gril.

ATTENTION: Tournez toujours la valve principale de

cylindre de propane au loin après chaque utilisation, et

avant de déplacer le gril et le cylindre, ou débrancher

l’accouplement. Cette valve doit rester fermée et le cylindre

a débranché alors que l’appareil n’est pas en service,

quoique l’écoulement de gaz soit arrêté par un dispositif de

sûreté quand le coupleur est débranché.

Inspectez soigneusement l’ensemble de tuyau chaque

fois avant que le gaz soit allumé. Un tuyau ssuré ou

efloché doit être immédiatement remplacé.

Si l’appareil est stocké à l’intérieur, le cylindre doit être

disconnected et a enlevé. Des cylindres Disconnected

doivent être stockés dehors, hors de la portée des enfants,

avec les prises de valve letées étroitement installées, et

ne doivent pas être stockés dans un bâtiment, le garage,

ou n’importe quel autre secteur inclus.

POUR VOTRE SÛRETÉ

a. Ne stockez pas un cylindre de gaz disponible de

propane dessous ou ne vous approchez pas de cet

appareil.

b. Ne remplissez jamais cylindre au delà de 80 pour cent

de plein.

c. SI L’INFORMATION DANS “A” ET “B” N’EST PAS

SUIVIE EXACTEMENT, UN FEU CAUSANT LA MORT

OU DES DOMMAGES SÉRIEUX PEUT SE PRODUIRE.

MPORTANT POUR VOTRE SÛRETÉ

LISEZ ET SUIVEZ TOUS LES AVERTISSEMENTS ÉQUIPÉS DE VOTRE CYLINDRE DE GAZ DE PROPANE.

En actionnant cet appareil avec un cylindre de gaz de propane ON DOIT observer ces instructions et avertissements. LE

MANQUE DE FAIRE AINSI PEUT AVOIR COMME CONSÉQUENCE UNE INCENDIE OU UNE EXPLOSION SÉRIEUSE

QCC

Type 1

Valve

Valve de

décompression

Volant de

commande

Ajustage de

précision en laiton

de fil de 3 point

culminant

Régulateur

Passage

Tuyau

Écrou de main

avec le fil de

point culminant.

Indicateur

de niveau

de liquide

(facultatif)

(Fig. 1) Type coupleur rapide de l de point culminant d’I

1-A 1-B

PCG.rev04282017- 10:53

INSTALLATION

LOCATION PREPARATION

Prepare a  at, level surface capable of supporting the

weight of the stand-alone grill and convenient to the gas

supply if connecting to a gas line.

WHEELS AND CASTERS

To lock the casters press down on the lever with the word

“ON” stamped on it until it stops and the caster will not roll.

To unlock, pull up on the lever.

CONNECT THE GAS SUPPLY

For connecting a propane unit to a portable propane tank,

read the safety warnings and follow the instructions in the

section SAFE USE AND MAINTENANCE OF PROPANE

GAS CYLINDERS.

For household propane or natural gas units:

1. Turn OFF the gas supply at the source. The quick

disconnect hose is pre-installed on the valve manifold

at the manufacturer. Run the hose through the hole

in the bottom rear of the stand-alone unit, to the gas

supply.

2. A shut-off valve is required within 6 feet of the unit.

3. Connect the quick connect hose to the shut-off valve

OR gas supply using a pipe joint compound resistant to

all gasses (see Below). Tighten securely.

Quick Connector

(can be connected directly to gas

supply stub if shut-off valve is

installed in-line)

Quick Connect Hose

(coming from unit)

Shut-Off Valve

(*required, not included, must be

installed within 6 feet of the unit)

Gas Supply

4. Turn all burner valves to the OFF position. Turn the gas

supply on. Then carefully check all gas connections

for leaks with a brush and soapy water before lighting.

NEVER USE A MATCH OR OPEN FLAME TO TEST

FOR LEAKS.

INSTALL THE FLAVOR GRIDS

Place the  avor grids directly onto the studs as shown

below. The  avor grids allow heat from the burners to be

evenly distributed throughout the cooking area. See Below.

INSTALL THE COOKING GRIDS

Place each cooking grid onto the left and right grid rests of

the grill. See Below.

INSTALL THE DRIP TRAY

You may line the drip tray with aluminum foil at this time.

Fully insert the drip tray into the bottom front of the control

panel. See Below.

unlocked position locked position

PCG.rev04282017- 10:53

INSTALLATION (continued)

IDENTIFYING THE GRILL CONTROLS

INSTALL THE IGNITER BATTERY

1. Grasp the cap/botton of the igniter and unscrew it in a

counter-clockwise motion (see below).

2. Install 1 AAA battery with the positive (+) pointing

outward.

positive(+)

3. Screw the igniter cap/button back onto the igniter in a

clockwise motion (see below).

DROP-SHELF OPERATION

A. To lower the shelf, grasp the middle of the shelf on both

sides and lift upward until the shelf does not move upward

any further. Then allow the end of the shelf to slowly rotate

down as pictured to below.

B. To raise the shelf, perform the opposite of A. above.

Grab the and raise to the horizontal position. The shelf

should slide downward and  t level with the adjacent

surface.

A B

CAUTION:

DO NOT place  ngers near hinges when opening, raising

or lowering the side shelves.

Igniter

Left Burner Low

Control Knob

Left Burner High

Control Knob

Right Burner High

Control Knob

Right Burner Low

Control Knob

PCG.rev04282017- 10:53

LIGHTING (IGNITION) INSTRUCTIONS

Read all instructions before lighting, and follow these instructions each time you light the unit.

ELECTRONIC LIGHTING

1. Open lid.

2. Turn all gas control knob(s) to their OFF position(s).

3. Turn on the gas at its source and press the master

switch.

Note: DO NOT turn on more than one valve at a time for

either electronic or manual lighting.

To Turn OFF

Press knob in to turn

OFF

Position

Use HI (high)

to light

To Turn ON

Fig. 1 - Control knob

4. Depress the desired control knob for 5 seconds, then,

while pressing turn it counterclockwise to the HI LIGHT

position. Press and hold the igniter button. Once the

burner lights, release igniter button.

CAUTION:

If a burner does not light within  ve (5) seconds of turning

on the control knob, depress the knob and turn it to the

OFF position. WAIT FIVE (5) MINUTES before repeating

step 4. If you smell gas, follow the instructions on the cover

of this manual. If the burners still do not light after several

attempts, refer to the instructions for manual lighting.

5. Repeat step 4 for each additional burner to be lit.

WHEN USING A PORTABLE PROPANE TANK

Propane tanks are equipped with a safety shutdown

device that may cause low or no gas pressure/ ame at

the burners if operating and lighting instructions are not

followed exactly (See important note in the TROUBLE-

SHOOTING section for more details.)

MANUAL LIGHTING

CAUTION: Always wait  ve (5) minutes for gas to clear

after any unsuccessful lighting attempt.

1. Follow steps 1 through 3 (left).

2. Insert either a burning long-barrel butane lighter or a

burning long-stem match through a hole in the control

panel opening to the top of the lighting tube (Fig. 2).

For backburners, hold the  ame against the surface of

the backburner.

3. Hold the match/lighter  ame at the top of the

lighting tube for 5 seconds. Then depress the

appropriate control knob and while pressing turn it

counterclockwise to the HI LIGHT position. Remove

the lighter or match when the burner lights, and release

the control knob.

4. If the burner does not light within  ve (5) seconds of

turning the control knob, immediately depress the

knob and turn the valve to OFF. WAIT FIVE (5)

MINUTES before repeating steps 2 through 4 of the

MANUAL LIGHTING instructions.

Fig. 2 - Manual lighting

SHUTTING OFF THE UNIT

To shut off the unit, depress each valve control knob and

while pressing turn it clockwise to the OFF position.

Always close the valve from the gas supply after each use

of the unit.

PCG.rev04282017- 10:53

ALLUMAGE DES INSTRUCTIONS (D’ALLUMAGE)

Lisez toutes les instructions avant l’allumage, et suivez ces instructions chaque fois vous lumière le unité.

ÉCLAIRAGE ÉLECTRONIQUE

1. Ouvrez les couvercles.

2. Tournez tous les boutons de commande de gaz à leurs

positions de repos.

3. Allumez le gaz à sa source et appuyez sur l’interrupteur

principal.

Note: N’ouvrez pas plus d’une valve à la fois pour

l’éclairage électronique ou manuel.

OUTRE DE

Enfoncez le bouton

pour tourner

Lisez l’établissement ici

(OUTRE de montrer)

UtiIlsation

SALUT (haute)

à la lumière

SUR

Fig. 1 - bouton de commande

4. Diminuez le bouton de commande désiré pendant

5 secondes, puis, et tout en pressant le tour il dans

le sens contraire des aiguilles d’une montre dans la

position LÉGÈRE de HI. Maintenez enfoncée la touche

allumeur. Une fois que le brûleur s’allume, relâchez le

bouton allumeur.

ATTENTION :

5. Si un brûleur ne s’allume pas dans cinq (5) secondes

d’allumer le bouton de commande, enfoncez le bouton

et tournez- le à la position de repos. ATTENDEZ CINQ

(5) MINUTES avant de répéter l’étape 4. Si vous

sentez le gaz, suivez les instructions sur la couverture

de ce manuel. Si les brûleurs ne s’allument toujours

pas après que plusieurs tentatives, se rapportent aux

instructions pour l’éclairage manuel.

EN EMPLOYANT UN RÉSERVOIR DE PROPANE PORTATIF

Des réservoirs de propane sont équipés d’un dispositif

d’arrêt de sûreté qui peut ne pas causer le bas ou

aucunes pression de gaz/ amme aux brûleurs si le

fonctionnement et l’allumage des instructions ne sont pas

suivis exactement (voir la note importante dans la section

de dépannage pour plus de détails.)

ÉCLAIRAGE MANUEL

ATTENTION: Attendez toujours cinq (5) minutes le gaz

pour se dégager après que n’importe quelle tentative non

réussie d’éclairage.

1. Suivez les étapes 1 à 3 (à gauche).

2. Insérez soit un briquet allumage à long canon bouillant,

soit une allumette brûlante à long manche, à travers

un trou dans le panneau de commande qui s’ouvre

au sommet du tube d’éclairage (Figure 2). Pour des

backburners, tenez la  amme contre le surface du

backburner.

3. Vieux match /  amme d’un briquet à la partie

supérieure du tube d’éclairage pendant 5 secondes.

Puis appuyer sur le bouton de contrôle approprié et

en appuyant tourner dans le sens antihoraire à la

position HI LIGHT. Retirez le briquet ou des allumettes

quand le brûleur s’allume, puis relâchez le bouton de

commande..

4. Si le brûleur ne se allume pas dans les cinq (5)

secondes de tourner le bouton de commande,

enfoncez immédiatement le bouton et tournez la

valve à AU LOIN. ATTENDEZ CINQ (5) MINUTES

avant de répéter les étapes 2 à 4 des instructions

manuelles d’éclairage.

Fig. 2 - Éclairage manuel

ARRÊT DU UNITÉ

Pour couper le unité, diminuez chaque bouton de

commande de valve et tout en pressant tour il dans le sens

des aiguilles d’une montre à la position de repos.

Fermez toujours la valve de la fourniture de gaz après

chaque utilisation du unité.

PCG.rev04282017- 10:53

CONVERT GAS TYPE / CHECK BURNER ORIFICES

CAUTION:

Make sure the grill is at a safe temperature and

isolated from gas and electrical supplies before

beginning.

For your safety, exercise caution, and make sure you have

adequate hand protection, such as gloves, when handling

metal parts.

APPLY CONVERSION LABEL

This grill comes from the factory congured for one type of

gas as marked on the label inside the cabinet.

When the grill is converted, the label for the new gas

(included at original shipping) MUST be lled out and

applied next to the existing label mentioned above.

CONVERT GAS ORIFICES

When converting the grill to a different gas type, each

burner’s orice must be replaced with the corresponding

orice for the new gas.

See MODEL SPECIFICATIONS TABLE, on page 1 at the

beginning of this document to determine the proper orice

sizes for each burner.

See the following sections for details on orice conversion.

Important: It is critical to the operation of each burner

that its orice be fully inserted into the center of its

orice opening.

WARNING

HAZARDOUS OVERHEATING WILL OCCUR IF A

NATURAL-GAS ORIFICE IS USED WITH PROPANE

GAS.

CONNECT TO NEW GAS SUPPLY

Plumb the unit as appropriate for the new gas supply.

(Additional components may be needed for your specic

setup.) Be sure to leak test at all connections.

Natural-gas to propane-gas conversions using a tank

internal to a portable grill require installation of a propane

tank holder (not included). This tank holder must be

purchased separately from the manufacturer.

CONVERT/CHECK MAIN BURNER ORIFICES

1. Remove the cooking grid and avor grid from above

the burner you are working on and set them aside.

2. Remove the screw from the left or right burner (Figure

1).

3. Lift the back end of the burner upward, then move the

burner toward the back of the grill to clear the gas inlet

and set it aside.

Figure 1

4. Use a 3/8" hex nut driver to remove the exposed orice

(Figure 2). Check orice. If needed, replace it with the

correct orice for the new gas.

Figure 2

5. Replace the burner by rst sliding the open cylindrical

end of the burner around the orice, enveloping it and

centering on it, then lower the back end anchor pegs

into the anchor peg holes.

Note: It is critical to the continued safe functioning of the

burner that the orice is centered and completely

inside the burner gas inlet (Figure 3).

6. Reinsert the screw through burner and tighten.

7. Replace the avor grid and then the cooking grid.

8. Repeat these steps for each burner.

Figure 3

La page charge ...

Primo 200 Le manuel du propriétaire

Marque: Primo

Modèle: 200

Catégorie: Barbecues

Taper: Le manuel du propriétaire

Ce manuel convient également à

Télécharger le PDF

rapport

dans d''autres langues

English: Primo 200 Owner's manual

Primo 200 Le manuel du propriétaire

Ce manuel convient également à

Primo 200 Le manuel du propriétaire

dans d''autres langues

Autres documents