Sony DCR-IP55 Manuel utilisateur

3-075-396-11 (2)

Network Function

Operating Instructions/

Mode d’emploi de la

fonction réseau

Registration code

2-GB

On trademarks

•“Memory Stick” and are registered trademarks of Sony Corporation.

•The BLUETOOTH trademarks are owned by their proprietor and used by Sony

Corporation under license.

•NetFront by Access Co., Ltd. is adopted for the Internet function of this product.

NetFront is a registered trademark of Access Co., Ltd in Japan.

•Portions of the supplied software are based partially on the work of the Independent

JPEG Group.

All other product names mentioned herein may be the trademarks or registered

trademarks of their respective companies. Furthermore, “™” and “®” are not

mentioned in each case in this manual.

No compensation for your recordings

Any recording contents or downloaded files cannot be compensated for being lost due

to redording/playback malfunction or storage media problems.

Precautions

•Before using the network function, make sure to set the clock on the camcorder. For

details, refer to the operating instructions of the camcorder. If you use the network

function without setting the clock, you may not be able to send/receive email or view

a web page.

•Do not remove the battery pack or disconnect the AC power adaptor while operating

in NETWORK mode. The setup for the NETWORK mode may be lost. Also, exit the

NETWORK mode when setting the POWER switch to OFF (CHG) or switching the

mode. These are to prevent the NETWORK mode setup from being lost.

•It is recommended that you make backup copies of your email messages and your

network preferences. These may be lost from time to time due to memory corruption.

To save the network preferences, write them down on paper, or use “Setup memo,”

described (p. 82). Also, this data may be lost when the camcorder is repaired by

services.

•The reset button cannot reset the network preferences.

Note on network operation when using the battery pack

When the remaining battery time is insufficient in NETWORK mode, use the AC power

adaptor or replace the battery pack with a fully charged battery pack. Before connecting

the AC power adaptor or replacing the battery pack, be sure to exit the NETWORK

mode.

Note on the network function

The network function is only available in the following countries or areas:

Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Luxembourg,

Netherlands, Norway, Portugal, Sweden, Switzerland, United Kingdom, and Spain. (As

investigated by Sony Corporation on 1. 8. 2001)

When using the camcorder in a country or area not described above, the network

function is available only in the country or area where you purchased the camcorder.

For customers in CANADA

Operation is subject to the following two conditions: (1) this device may not cause

interference, and (2) this device must accept any interference, including interference

that may cause undesired operation of the device.

To prevent radio interference to the licensed service, this device is intended to be

operated indoors and away from windows to provide maximum shielding. Equipment

that is installed outdoors is subject to licensing.

3-GB

Introduction

Table of contents

Introduction

The network function on the camcorder... 4

Basic operations in the NETWORK mode

.................................................................. 5

How to use the Network Menu .......... 5

How to hold your camcorder when

operating in the NETWORK

mode ................................................ 6

How to use the stylus .......................... 7

How to input characters ...................... 8

Character input display ..................... 10

The available character list ................ 11

Character input setting ...................... 16

Preparation

Overview of the Bluetooth wireless

technology ............................................17

Registering a Bluetooth device ......... 18

Using your Modem Adaptor with

Bluetooth Function ...................... 18

When the registration has failed ...... 22

Displaying information on your

camcorder ..................................... 23

Radio wave indication ....................... 24

Selecting other Bluetooth devices

from the list .................................. 24

Deleting a registered Bluetooth

device from the list ...................... 24

Internet service provider ........................... 26

Setting network preferences ..................... 27

Network Operation

Using email..................................................33

Sending email...................................... 33

Using the address book ..................... 44

Receiving email ................................... 50

Deleting unnecessary email .............. 55

Viewing web pages ....................................57

Viewing web pages ............................ 57

How to use the menu bar on the

browser ......................................... 59

Storing the web page into a

“Memory Stick”

– Page Memo ................................ 65

Shutting down the browser .............. 70

Additional Information

File storage destinations and file names

................................................................ 71

Troubleshooting..........................................72

Trouble accessing the Internet .......... 72

Trouble with email ............................. 73

Trouble viewing web pages .............. 74

Adjusting the LCD screen

(CALIBRATION) ......................... 75

Specifications...............................................76

Messages ......................................................77

General ................................................. 77

Email..................................................... 78

Browser ................................................ 79

Glossary ....................................................... 80

Setup memo.................................................82

4-GB

Congratulations on your purchase of this Sony Handycam. This Handycam can access

to the Internet through your provider using a dial-up networking connection with a

Bluetooth device. You can view web pages, receive email, and send email with images

recorded on your camcorder attached. The communication system is Bluetooth Ver.1.1

and its compatible Bluetooth profiles are the “Generic Access Profile” and the “Dial-up

Networking Profiles”.

– Introduction –

The network function on the camcorder

Easy access to

the Internet

You can view a web page

via the Internet.

You can send or receive email

anytime, and attach images to

email messages.

Send/receive your emails

Set the camcorder’s clock setting before using the Network functions. (The default setting is OFF.)

If you do not set the clock setting, you cannot send and receive emails or view web pages.

You also have to set up your camcorder and the peripheral device.

5-GB

Introduction

This section describes basic control ways to operate your camcorder, those which are

used for network operations.

How to use the Network Menu

To access the Network Menu, refer to “Accessing the network” in the operating

instructions supplied with your camcorder.

[a]: Send and receive email. For details, see “Using email” (p. 33).

[b]: View a web page through the Internet. For details, see “Viewing web pages”

(p. 57).

[c]: You have to make various settings using this menu before using the network

function. For details, see “Setting network preferences” (p. 27).

[d]: Exit the NETWORK mode.

The actual screens may differ slightly from the illustrations in this network

function operating instructions.

Basic operations in the NETWORK mode

[a]

[b]

[c]

[d]

6-GB

How to hold your camcorder when operating in the NETWORK

mode

When operating in the NETWORK mode, you can turn the LCD panel over and move it

back to your camcorder with the LCD screen facing over to use the stylus (for touch

panel operation, supplied).

1 Turn the LCD panel over and move it back to your camcorder with the LCD

screen facing over.

2 Hold your camcorder as illustrated below when you operate.

The way to hold and operate your camcorder varies depending on the model.

For detail, refer to the “Operating Instructions” supplied with your camcorder.

Basic operations in the NETWORK mode

7-GB

Introduction

How to use the stylus

The buttons required for operating your camcorder are displayed on the LCD screen.

Operate by pressing the buttons on the screen directly but lightly with the stylus

provided. In this manual, pressing the buttons in this way using the stylus is referred to

as “tapping”.

Tap the desired button on the screen with the stylus.

The selected button turns orange.

,

Notes

•Do not tap them with sharp-pointed objects other than the stylus supplied.

•Do not tap the LCD screen too hard.

•Do not touch the LCD screen with wet hands.

•When the LCD screen gets dirty, use the supplied cleaning cloth.

•You cannot drag icons, like on a computer, by touching and sliding across your

camcorder screen with the stylus.

•Refer to the operating instructions supplied with your camcorder for the stylus

storage location. To avoid losing the stylus, we recommend that you return it to the

storage location after use.

Basic operations in the NETWORK mode

8-GB

How to input characters

You have to frequently enter characters, such as email addresses, or web pages

addresses (URL), to use the network function. This section describes how to input

characters.

1

(1) Open the Network Menu.

For details on how to open the Network Menu, refer to “Accessing the

network” in the operating instructions supplied with your camcorder.

(2) Tap [

Mail].

The Send screen appears.

,

(3) Tap [To].

,

(4) Tap [ New].

The character input screen appears.

,

Basic operations in the NETWORK mode

9-GB

Introduction

2 Selecting the character type

Tap [abcy123], then tap the desired character type.

abc: When inputting alphabetical characters.

123: When inputting numerical characters.

When you selected abc When you selected 123

3 Inputting characters

(1) Tap the character you want to input.

(2) After you input the characters, tap [Enter].

The screen which is displayed before you display the character input screen

appears.

Basic operations in the NETWORK mode

10-GB

Basic operations in the NETWORK mode

1 [a/A] button

[a/A] button is displayed when you input alphabetical characters.

You can switch between upper case and lower case.

2 [abcy123] button

A list box appears when you tap the [abc y 123] button. Tap the desired

type of letter from the list box.

3 Input byte number/maximum byte number

4 Preferences

You can change the keyboard type for alphabet input.

5 Text area

You can scroll up or down the display by tapping v or V.

6 [Space] button

A space is entered.

7 [Back space] button

The letter right before the cursor is deleted. If you tap the button for

about three seconds, all the characters before the cursor are deleted.

8

button

The cursor moves to a new line.

9 [Enter] button

Tap this button to decide or close the input screen.

1

2

6

78

9

5

4

3

Character input display

11-GB

Introduction

Symbol characters

The symbol characters below are inputted by single tapping:

The green keys input the symbol characters.

The symbol characters change as follows:

Basic operations in the NETWORK mode

The available characters list

When selecting [abc]

Alphabetical characters

The alphabet keyboard has 2 types (PC Style and Alphabetical order). The default

setting is PC arrangement. You can change the keyboard setting in . Refer to page 16

for more information.

(PC Style) (Alphabetical order)

Key Character

` ´ ˆ

* a: à t á t â t a t... A: À t Á t Â t A t...

e: è t é t ê t e t... E: È t É t Ê t E t...

i: ì t í t î t i t... I: Ì t Í t Î t I t...

o: ò t ó t ô t o t... O: Ò t Ó t Ô t O t...

u: ù t ú t û t u t... U: Ù t Ú t Û t U t...

y:

´y

t y t... Y:

´

Y

t Y t...

¨ ˜

* a: ä t ã t a t... A: Ä t Ã t A t...

e: ë t e t... E: Ë t E t...

i: ï t i t... I: Ï t I t...

n: ñ t n t... N: Ñ t N t...

o: ö t õ t o t... O: Ö t Õ t O t...

u: ü t u t... U: Ü t U t...

y: ÿ t y t...

’ ”

’ t ” t ’ t ...

? ¿

? t ¿ t ? t ...

! ¡

! t ¡ t ! t ...

ç

Ç

ß

ç t Ç t ß t ç t...

. ,

. t , t . t ...

/ \

/ t \ t / t ...

abcdefghi j klm

nopqr s tuvwxy z

ABCDEFGHI J KLM

NOPQR S TUVWXY Z

* You can input the alphabet characters with accent symbols. When you input the

characters, tap

` ´ ˆ

or

¨ ˜

after inputting a, e, i, n, o, u, y, A, E, I, N, O, U or Y.

~ – _

@

:

12-GB

To switch between upper and lower case alphabet letters

Tap [a/A] to change the alphabetical keyboard, then enter characters.

To delete a character

Move the cursor with the stylus to the right of the character at which you want to

delete, tap [Back space]. The character at the left of the cursor is deleted.

To add a character

Move the cursor with the stylus to the position at which you want to add a character,

then input characters.

To start a new line

Tap [ ].

When selecting [123]

Symbol characters

(Numerical order)

Basic operations in the NETWORK mode

123+( )$

C

\%

456– []&ˆ | ˜

789/{}`”’ ,

* 0#=<> . : ; _

13-GB

Introduction

E.g., Enter “Hello” into the Subject item on the Send screen

1

(1) Open the Network Menu.

For details on how to open the Network Menu, refer to “Accessing the

network” in the operating instructions supplied with your camcorder.

(2) Tap [

Mail].

The Send screen appears.

,

2 Entering the subject of a message

(1) Tap [Subject].

(2) Tap [

New].

The character input screen appears.

,

Basic operations in the NETWORK mode

14-GB

3

(1) Tap [abcy123], then tap [abc].

(2) Tap [a/A] to be able to enter upper-case letters.

,

(3) Tap [H].

“H” is entered.

,

(4) Tap [a/A] to be able to enter lower-case letters.

,

Basic operations in the NETWORK mode

15-GB

Introduction

(5) Tap [e].

“e” is entered.

,

(6) Tap [l], [l] and [o].

“llo” is entered.

,

(7) Tap [Enter].

“Hello” is entered and the Send screen appears again.

,

Basic operations in the NETWORK mode

16-GB

Character input setting

Keyboard

You can change the display of the alphabet, PC arrangement keyboard or ABC

arrangement keyboard into a setup you want when you input characters.

1 Tap in the character input screen.

,

2 Tap the desired setting.

You can set as the following two displays when [abcy123] is set as [abc].

(PC Style is the default setting.)

– PC Style (PC arrangement keyboard)

– Alphabetical order (ABC arrangement Keyboard)

To switch the setting, tap on the upper-right LCD screen.

Alphabetical orderPC Style

Basic operations in the NETWORK mode

Preparation

17-GB

– Preparation –

Overview of the Bluetooth wireless

technology

What is the Bluetooth wireless technology?

The Bluetooth wireless technology allows communication between various Bluetooth

devices without using cables. Devices which can use this technology include PCs,

computer peripheral devices, PDAs, and mobile phones. This omnidirectional

communication system enables communication even if the Bluetooth device is in a bag

or having obstacles between the devices.

Also, the Bluetooth wireless technology has advanced security functions, such as

scrambled frequencies and data encryption.

Authentication

The authentication routine can block unspecified users’ access to this network. When

attempting communication with an unregistered Bluetooth device, the devices must

first be registered with each other by entering a common passkey to each device. When

connecting with a previously registered Bluetooth device, communication starts

without entering the passkey.

18-GB

Registering a Bluetooth device

This section describes making a registration of a Bluetooth device. Here we describe the

procedure for registering the Sony Modem Adaptor with Bluetooth Function. Once the

registration is completed, your camcorder can connect to your Bluetooth device without

reregistering the device. You can register up to three Bluetooth devices. Also, refer to

the operating instructions supplied with your Bluetooth device.

For more information about Bluetooth devices compatible with your camcorder, access

the following URL:

For customers in Canada

“http://www.sony.ca/service/”

For customers in the areas other than in Canada

“http://www.css.ap.sony.com/”

Notes

•When using Sony BTA-NW1/BTA-NW1A Modem Adaptor with Bluetooth Function,

place it at a location that has no obstacles between your camcorder and the device.

The distance between the devices must be within 10 m (33 feet).

•The connection may be interrupted depending on the communication conditions.

Using your Modem Adaptor with Bluetooth Function

1 Preparing the Modem Adaptor with Bluetooth Function

Set the Modem Adaptor with Bluetooth Function to connection standby (BONDING).

For details, refer to the operating instructions supplied with your Modem Adaptor with

Bluetooth Function.

Overview of the Bluetooth wireless technology

Preparation

19-GB

2 Specifying your Modem Adaptor with Bluetooth Function as the

connection device

(1) Open the Network Menu.

For details on how to open the Network Menu, refer to “Accessing the

network” in the operating instructions supplied with your camcorder.

(2) Tap [

Setup].

The Setup screen appears.

,

(3) Tap [Bluetooth Setup].

The Bluetooth Setup screen appears.

,

Overview of the Bluetooth wireless technology

20-GB

(4) Tap [Select].

The Bluetooth devices list appears. When making a registration for the first

time, only [

Return] and [ New] are indicated. The list shows up to three

Bluetooth devices. You can select one of the latest used three Bluetooth devices

from the list.

,

Tip

The last-used Bluetooth device is listed next to [

Return] and [ New].

(5) Tap [

New].

Your camcorder starts searching for your Bluetooth devices. When the

searching is completed, the available Bluetooth devices list appears.

When some Bluetooth devices with same name appear, display each Bluetooth

device address by tapping [More info.].

,,

Notes

•The search takes from about 10 to 60 seconds. The time depends on the number of

Bluetooth devices around your camcorder.

•If the Bluetooth device you want to register is not found, carry out the procedure

again from step 4.

(6) Tap the desired Bluetooth device.

The character input screen appears.

,

Overview of the Bluetooth wireless technology

La page charge ...

Sony DCR-IP55 Manuel utilisateur

Ce manuel convient également à

Sony DCR-IP55 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents