Stanley SFMCMW2653B Le manuel du propriétaire

SFMCMW2653

Final page size: A5 (148mm x 210mm)

www.stanleytools.eu

B

Copyright STANLEYFATMAX

English (original instructions) 4

Deutsch (übersetzt von den originalanweisungen) 16

Français (traduction de la notice d’instructions originale) 29

Italiano (tradotto dalle istruzioni originali) 42

Nederlands (vertaald vanuit de originele instructies) 55

Español (traducido de las instrucciones originales) 68

Português (traduzido das instruções originais) 81

Svenska (översatt från de ursprungliga instruktionerna) 94

Norsk (oversatt fra de originale instruksjonene) 106

Dansk (oversat fra original brugsvejledning) 117

Suomi (käännetty alkuperäisestä käyttöohjeesta) 129

Ελληνικά (μετάφραση από τις πρωτότυπες οδηγίες) 140

1

Fig.A

38

5

8

9

10

11

13

14

7

15

6

16

4

12

6

1

2

3

Fig.B

6

4

34

7

Fig.C

18

11

1235

2

Fig.H

Fig.G

Fig.D Fig.E

Fig.I

Fig.F

21

20

19

9

10

22

3

1

5

3

2

4

6

7

14

3

Fig.N

Fig.M

Fig.J Fig.K

Fig.L

32

29

33

29

32

34

23

25

24

30

28

27

26

24

29

28

23

25

24

4

ENGLISH

“X” Indicates that the battery pack is compatible with that

specific charger. Read the instruction manual for more

specificinformation.

EC-Declaration of Conformity

Machinery Directive

Lawn Mower

SFMCMW2653

STANLEYFATMAX declares that these products described under

Technical Data are in compliance with:

2006/42/EC, EN60335-1:2012 + A11:2014, EN60335-2-77:2010.

These products also comply with Directive 2014/30/EU

and 2011/65/EU. For more information, please contact

STANLEYFATMAX at the following address or refer to the back

of themanual.

The undersigned is responsible for compilation of the technical

file and makes this declaration on behalf ofSTANLEYFATMAX.

2000/14/EC, Lawn Mower, 50<L≤70cm, Annex VI, DEKRA

Certification B.V., Meander 1051 / P.O. Box 5185

6825 MJ ARNHEM / 6802 ED ARNHEM, Netherlands

Notified Body ID No.: 0344

Level of acoustic power according to 2000/14/EC

(Article12,Annex III, 50 <L ≤ 70 cm):

L

PA

(emission sound pressure) 78.0 dB(A)

uncertainty (K) = 1,4 dB(A)

L

WA

(guaranteed sound power) 98 dB(A)

A. P. Smith

Technical Director

STANLEYFATMAX Europe, Egide Walschaertsstraat14-18,

2800 Mechelen, Belgium

2019-10-11

WARNING: To reduce the risk of injury, read the

instructionmanual.

Definitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to

thesesymbols.



DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.



WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.

Congratulations!

You have chosen a STANLEYFATMAX tool. Years of experience,

thorough product development and innovation make

STANLEYFATMAX one of the most reliable partners for

professional power toolusers.

Technical Data

SFMCMW2653

Voltage V

DC

54

Type 1

Battery type Li-Ion

No load speed rpm 3300

Blade Length cm 51

Weight (without battery pack) kg 33

Noise values and vibration values (triax vector sum) according to EN60335:

L

PA

(emission sound pressure level) dB(A) 78.0

L

WA

(sound power level) dB(A) 91.5

K (uncertainty for the given sound level) dB(A) 0.8

Hand/arm weighted vibration value:

Vibration emission value a

h

= m/s

2

<2.5

Uncertainty K = m/s

2

1.5

The vibration emission level given in this information sheet has

been measured in accordance with a standardised test given in

EN60335 and may be used to compare one tool with another. It

may be used for a preliminary assessment ofexposure.



WARNING: The declared vibration emission level

represents the main applications of the tool. However if

the tool is used for different applications, with different

accessories or poorly maintained, the vibration emission

may differ. This may significantly increase the exposure

level over the total workingperiod.

An estimation of the level of exposure to vibration should

also take into account the times when the tool is switched

off or when it is running but not actually doing the job.

This may significantly reduce the exposure level over the

total workingperiod.

Identify additional safety measures to protect the operator

from the effects of vibration such as: maintain the tool

and the accessories, keep the hands warm, organisation of

workpatterns.

Battery

Cat #

Output

Voltage

Ah

Charger

SFMCB6012

SFMCB6025 54 2.5 X

SFMCB605 54 5 X

SFMCB6075 54 7.5 X

English (original instructions)

54V LAWN MOWER

SFMCMW2653

5

ENGLISH



CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.



Denotes risk of electricshock.



Denotes risk offire.

Safety Instructions



WARNING: When using cordless appliances, basic safety

precautions, including the following, should always be

followed to reduce the risk of fire, electric shock, personal

injury and materialdamage.



WARNING: When using the machine the safety rules must

be followed. For your own safety and bystanders please

read these instructions before operating the machine.

Please keep the instructions safe for lateruse.

• Read all of this manual carefully before operating

theappliance.

• The intended use is described in this manual. The use

of any accessory or attachment or the performance

of any operation with this appliance other than those

recommended in this instruction manual may present

a risk of personalinjury.

• Retain this manual for futurereference.

SAVE ALL WARNINGS AND

INSTRUCTIONS

FOR FUTURE REFERENCE

Using Your Appliance

Always take care when using theappliance.

• This appliance is not intended for use by young or infirm

persons withoutsupervision.

• The appliance is not to be used as atoy.

• Do not allow children or animals to come near the work area

or touch theappliance.

• Close supervision is necessary when the appliance is used

nearchildren.

• Use in a dry location only. Do not allow the appliance to

becomewet.

• Do not immerse the appliance inwater.

• Do not open body casing. There are no user serviceable

partsinside.

• Do not operate the appliance in explosive atmospheres, such

as in the presence of flammable liquids, gases ordust.

• Before using, always visually inspect to see that the blades,

blade bolts and cutter assembly are not worn or damaged.

Replace worn or damaged blades and bolts in sets to

preservebalance.

• Never operate the machine while people, especially children, or

pets arenearby.

• Keep in mind that the operator or user is responsible

for accidents or hazards occurring to other people or

theirproperty.

Before Use

• While operating the machine always wear substantial

footwear and long trousers. Do not operate the machine when

barefoot or wearing open sandals. Avoid wearing clothing

that is loose fitting or that has hanging cords orties.

• Thoroughly inspect the area where the machine is to be used

and remove all objects which can be thrown by themachine.

• Before using, always visually inspect to see that the blade,

blade bolt and the blade assembly are not worn or damaged.

Replace worn or damaged components in sets to preserve

balance. Replace damaged or unreadablelabels.

After Use

• When not in use, the appliance should be stored in a dry, well

ventilated place out of the reach ofchildren.

• Children should not have access to storedappliances.

• When the appliance is stored or transported in a vehicle

it should be placed in the boot or restrained to prevent

movement following sudden changes in speed ordirection.

Inspection and Repairs

• Before use, check the appliance for damaged or defective

parts. Check for breakage of parts, damage to switches and

any other conditions that may affect itsoperation.

• Do not use the appliance if any part is damaged ordefective.

• Have any damaged or defective parts repaired or replaced by

an authorised repairagent.

• Never attempt to remove or replace any parts other than those

specified in thismanual.

• Be careful during adjustment of the mower to prevent

entrapment of the fingers between moving blades/parts and

fixed parts of themachine.

• When servicing the blades be aware that, even though the

power source is switched off, the blades can still bemoved.

Additional Safety Instructions for

LawnMowers

• Do not transport the machine while the power source

isrunning.

• Firmly grip handle with both hands when operating the

lawnmower.

• If at any time it is felt necessary to tilt the lawn mower, make

sure that both hands remain in the operating position while

the lawn mower is tilted. Keep both hands in the operating

position until the lawn mower is returned to rest correctly on

theground.

• Never wear radio or music headphones while operating the

lawnmower.

• Never attempt to make a wheel height adjustment while

the motor is running or while the safety key is in the

switchhousing.

6

ENGLISH

• If the lawn mower stalls, release bail bar to turn mower off,

wait for blade to stop, before attempting to unclog the chute

or remove anything from under thedeck.

• Keep hands and feet away from cuttingarea.

• Keep blades sharp. Always use protective gloves when

handling the lawn mowerblade.

• If you are using the grass collector, check it frequently for wear

and deterioration. If excessively worn, replace with a new grass

collector for yoursafety.

• Use extreme caution when reversing or pulling the lawn

mower towardsyou.

• Do not put hands or feet near or under the lawn mower. Keep

clear of the discharger opening at alltimes.

• Clear the area where the lawn mower is to be used of objects

such as rocks, sticks, wire, toys, bones etc., which could be

thrown by the blade. Objects struck by the blade can cause

severe injury to persons. Stay behind the handle when the

motor isrunning.

• Do not operate the lawn mower barefooted or while wearing

sandals. Always wear substantialfootwear.

• Do not pull lawn mower backward unless absolutely

necessary. Always look down and behind before and while

movingbackward.

• Never direct discharged material toward anyone. Avoid

discharging material against a wall or obstruction. Material

may ricochet back toward the operator. Release the bail bar

to turn the lawn mower off and stop the blade when crossing

gravelsurfaces.

• Do not operate the lawn mower without the entire grass

collector, discharge guard, rear guard, or other safety

protective devices in place and working. Periodically check all

guards and safety protective devices to ensure they are in good

working order and will operate properly and perform their

intended function. Replace a damaged guard or other safety

device before furtheruse.

• Never leave a running lawn mowerunattended.

• Always release the bail bar to stop the motor and wait until

the blade comes to a complete stop before cleaning the lawn

mower, removing the grass bag, unclogging the discharge

guard, when leaving the lawn mower, or before making any

adjustments, repairs orinspections.

• Operate lawn mower only in daylight or good artificial light

when objects in the path of the blade are clearly visible from

the operating area of the lawnmower.

• Do not operate the lawn mower while under the influence of

alcohol or drugs, or when you are tired or ill. Always stay alert,

watch what you are doing, and use commonsense.

• Avoid dangerous environments. Never operate the lawn

mower in damp or wet grass, never use lawn mower in the

rain. Always be sure of your footing, walk, neverrun.

• If the lawn mower should start to vibrate abnormally, release

the bail bar, wait for the blade to stop and then check for

the cause immediately. Vibration is generally a warning of

trouble, see the Troubleshooting for advice in the case of

abnormalvibration.

• Always wear proper eye and respiratory protection when

operating the lawnmower.

• The use of any accessory or attachment not recommended

for use with this lawn mower could be hazardous. Only use

accessories approved bySTANLEYFATMAX.

• Never overreach while operating the lawn mower. Always

be sure to keep proper footing and balance at all times while

operating the lawnmower.

• Mow across the face of slopes, never up and down. Exercise

extreme caution when changing direction onslopes.

• Watch for holes, ruts, bumps, rocks or other hidden objects.

Uneven terrain could cause a slip and fall accident. Tall grass

can hideobstacles.

• Do not mow on wet grass or excessively steep slopes. Poor

footing could cause a slip and fallaccident.

• Do not mow near drop-offs, ditches, or embankments. You

could lose your footing orbalance.

• Always allow the mower to cool down beforestoring.

• Pull the plug from the socket and pull the battery pack from

the machine. Make sure that all moving parts have come to a

complete stop:

ʵ Whenever you leave the machine;

ʵ Before clearing a blockage;

ʵ Before checking, cleaning or working on theappliance.

Safety of Others

• This appliance is not intended for use by persons (including

children) with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have

been given supervision or instruction concerning use of the

appliance by a person responsible for theirsafety.

• Children must be supervised to ensure that they do not play

with theappliance.

• After striking a foreign object. Inspect the appliance for

damage and make repairs asnecessary.

Residual Risks

In spite of the application of the relevant safety regulations

and the implementation of safety devices, certain residual risks

cannot be avoided. These are:

• Injuries caused by touching any rotating/movingparts.

• Injuries caused when changing any parts, blades

oraccessories.

• Injuries caused by prolonged use of a tool. When using any

tool for prolonged periods ensure you take regularbreaks.

• Impairment ofhearing.

• Health hazards caused by breathing dust developed when

using your tool (example:- working with wood, especially oak,

beech and MDF.)

• Never pick up or carry an appliance while the motor isrunning.

Electrical Safety

The electric motor has been designed for one voltage only.

Always check that the battery pack voltage corresponds to the

voltage on the rating plate. Also make sure that the voltage of

your charger corresponds to that of yourmains.

7

ENGLISH

Your STANLEYFATMAX charger is double insulated

in accordance with EN60335; therefore no earth wire

isrequired.

If the supply cord is damaged, it must be replaced by a specially

prepared cord available through the STANLEYFATMAX

serviceorganisation.

Mains Plug Replacement

(U.K. & Ireland Only)

If a new mains plug needs to be fitted:

• Safely dispose of the oldplug.

• Connect the brown lead to the live terminal in theplug.

• Connect the blue lead to the neutralterminal.



WARNING: No connection is to be made to the

earthterminal.

Follow the fitting instructions supplied with good quality plugs.

Recommended fuse: 3A.

Using an Extension Cable

An extension cord should not be used unless absolutely

necessary. Use an approved extension cable suitable for

the power input of your charger (see Technical Data). The

minimum conductor size is 1mm

2

; the maximum length

is30m.

When using a cable reel, always unwind the cablecompletely.

SAVE THESE INSTRUCTIONS

Chargers

STANLEYFATMAX chargers require no adjustment and are

designed to be as easy as possible tooperate.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instructions for compatible battery

chargers (refer to TechnicalData).

• Before using charger, read all instructions and cautionary

markings on charger, battery pack, and product using

batterypack.



WARNING: Shock hazard. Do not allow any liquid to get

inside charger. Electric shock mayresult.



WARNING: We recommend the use of a residual current

device with a residual current rating of 30mA orless.



CAUTION: Burn hazard. To reduce the risk of injury,

charge only STANLEYFATMAX rechargeable batteries.

Other types of batteries may burst causing personal injury

anddamage.



CAUTION: Children should be supervised to ensure that

they do not play with theappliance.

NOTICE: Under certain conditions, with the charger

plugged into the power supply, the exposed charging

contacts inside the charger can be shorted by foreign

material. Foreign materials of a conductive nature such as,

but not limited to, steel wool, aluminum foil or any buildup

of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply

when there is no battery pack in the cavity. Unplug charger

before attempting to clean

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger

and battery pack are specifically designed to worktogether.

• These chargers are not intended for any uses other

than charging STANLEYFATMAX rechargeable batteries.

Any other uses may result in risk of fire, electric shock

orelectrocution.

• Do not expose charger to rain orsnow.

• Pull by plug rather than cord when disconnecting

charger. This will reduce risk ofdamage to electric plug

andcord.

• Make sure that cord is located so that it will not be

stepped on, tripped over, or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk

of fire, electric shock, orelectrocution.

• Do not place any object on top of charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source. The

charger is ventilated through slots in the top and the bottom

of thehousing.

• Do not operate charger with damaged cord or plug—

have them replacedimmediately.

• Do not operate charger if it has received a sharp blow,

been dropped, or otherwise damaged in any way. Take it

to an authorised servicecentre.

• Do not disassemble charger; take it to an authorised

service centre when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution

orfire.

• In case of damaged power supply cord the supply cord must be

replaced immediately by the manufacturer, its service agent or

similar qualified person to prevent anyhazard.

• Disconnect the charger from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• NEVER attempt to connect two chargerstogether.

• The charger is designed to operate on standard

230V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

Charging a Battery(Fig.B)

1. Plug the charger into an appropriate outlet before inserting

batterypack.

2. Insert the battery pack

19

into the charger, making sure the

battery pack is fully seated in the charger. The red (charging)

light will blink repeatedly indicating that the charging

process hasstarted.

3. The completion of charge will be indicated by the red light

remaining ON continuously. The battery pack is fully charged

8

ENGLISH

and may be used at this time or left in the charger. To

remove the battery pack from the charger, push the battery

release button

20

on the batterypack.

NOTE: To ensure maximum performance and life of lithium-ion

battery packs, charge the battery pack fully before firstuse.

Charger Operation

Refer to the indicators below for the charge status of the

batterypack.

Charge Indicators

Charging

Fully Charged

Hot/Cold Pack Delay*

* The red light will continue to blink, but a yellow indicator light

will be illuminated during this operation. Once the battery pack

has reached an appropriate temperature, the yellow light will

turn off and the charger will resume the chargingprocedure.

The compatible charger(s) will not charge a faulty battery pack.

The charger will indicate faulty battery by refusing to light or by

displaying problem pack or charger blinkpattern.

NOTE: This could also mean a problem with acharger.

If the charger indicates a problem, take the charger and battery

pack to be tested at an authorised servicecentre.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot or too

cold, it automatically starts a Hot/Cold Pack Delay, suspending

charging until the battery pack has reached an appropriate

temperature. The charger then automatically switches to the

pack charging mode. This feature ensures maximum battery

packlife.

A cold battery pack will charge at a slower rate than a warm

battery pack. The battery pack will charge at that slower rate

throughout the entire charging cycle and will not return to

maximum charge rate even if the battery packwarms.

Wall Mounting

These chargers are designed to be wall mountable or to sit

upright on a table or work surface. If wall mounting, locate the

charger within reach of an electrical outlet, and away from a

corner or other obstructions which may impede air flow. Use

the back of the charger as a template for the location of the

mounting screws on the wall. Mount the charger securely using

drywall screws (purchased separately) at least 25.4mm long

with a screw head diameter of 7–9mm, screwed into wood to

an optimal depth leaving approximately 5.5mm of the screw

exposed. Align the slots on the back of the charger with the

exposed screws and fully engage them in theslots.

Charger Cleaning Instructions



WARNING: Shock hazard. Disconnect the charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using a

cloth or soft non-metallic brush. Do not use water or any

cleaning solutions. Never let any liquid get inside the tool;

never immerse any part of the tool into aliquid.

Battery Packs

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include

catalogue number andvoltage.

The battery pack is not fully charged out of the carton. Before

using the battery pack and charger, read the safety instructions

below. Then follow charging proceduresoutlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or

dust. Inserting or removing the battery from the charger may

ignite the dust orfumes.

• Never force battery pack into charger. Do not modify

battery pack in any way to fit into a non-compatible

charger as battery pack may rupture causing serious

personalinjury.

• Charge the battery packs only in STANLEYFATMAXchargers.

• DO NOT splash or immerse in water or otherliquids.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or exceed

40 ˚C (104 ˚F) (such as outside sheds or metal buildings

in summer).

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium-ion battery packs areburned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open eye

for 15 minutes or until irritation ceases. If medical attention

is needed, the battery electrolyte is composed of a mixture of

liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek

medicalattention.



WARNING: Burn hazard. Battery liquid may be flammable

if exposed to spark orflame.



WARNING: Never attempt to open the battery pack for

any reason. If battery pack case is cracked or damaged,

do not insert into charger. Do not crush, drop or damage

battery pack. Do not use a battery pack or charger that

has received a sharp blow, been dropped, run over or

damaged in any way (i.e., pierced with a nail, hit with

a hammer, stepped on). Electric shock or electrocution

may result. Damaged battery packs should be returned to

service centre forrecycling.



WARNING: Fire hazard. Do not store or carry the

battery pack so that metal objects can contact

exposed battery terminals. For example, do not place

the battery pack in aprons, pockets, tool boxes, product kit

boxes, drawers, etc., with loose nails, screws, keys,etc.



CAUTION: When not in use, place tool on its side on

a stable surface where it will not cause a tripping

or falling hazard. Some tools with large battery packs

9

ENGLISH

will stand upright on the battery pack but may be easily

knockedover.

Transportation



WARNING: Fire hazard. Transporting batteries can

possibly cause fire if the battery terminals inadvertently

come in contact with conductive materials. When

transporting batteries, make sure that the battery

terminals are protected and well insulated from materials

that could contact them and cause a shortcircuit.

STANLEYFATMAX batteries comply with all applicable shipping

regulations as prescribed by industry and legal standards which

include UN Recommendations on the Transport of Dangerous

Goods; International Air Transport Association (IATA) Dangerous

Goods Regulations, International Maritime Dangerous Goods

(IMDG) Regulations, and the European Agreement Concerning

The International Carriage of Dangerous Goods by Road (ADR).

Lithium-ion cells and batteries have been tested to section 38.3

of the UN Recommendations on the Transport of Dangerous

Goods Manual of Tests andCriteria.

In most instances, shipping a STANLEYFATMAX battery pack

will be excepted from being classified as a fully regulated Class

9 Hazardous Material. In general, only shipments containing a

lithium-ion battery with an energy rating greater than 100 Watt

Hours (Wh) will require being shipped as fully regulated Class

9. All lithium-ion batteries have the Watt Hour rating marked

on the pack. Furthermore, due to regulation complexities,

STANLEYFATMAX does not recommend air shipping lithium-ion

battery packs alone regardless of Watt Hour rating. Shipments of

tools with batteries (combo kits) can be air shipped as excepted

if the Watt Hour rating of the battery pack is no greater than

100Whr.

Regardless of whether a shipment is considered excepted

or fully regulated, it is the shipper's responsibility to consult

the latest regulations for packaging, labeling/marking and

documentationrequirements.

The information provided in this section of the manual is

provided in good faith and believed to be accurate at the time

the document was created. However, no warranty, expressed or

implied, is given. It is the buyer’s responsibility to ensure that its

activities comply with the applicableregulations.

Storage Recommendations

1. The best storage place is one that is cool and dry away

from direct sunlight and excess heat or cold. For optimum

battery performance and life, store battery packs at room

temperature when not inuse.

2. For long storage, it is recommended to store a fully charged

battery pack in a cool, dry place out of the charger for

optimalresults.

NOTE: Battery packs should not be stored completely depleted

of charge. The battery pack will need to be recharged beforeuse.

Fuel Gauge Battery Packs(Fig.C)

Some STANLEYFATMAX battery packs include a fuel gauge

which consists of three green LED lights that indicate the level of

charge remaining in the batterypack.

The fuel gauge is an indication of approximate levels of

charge remaining in the battery pack according to the

followingindicators:

75–100% charged

51–74% charged

< 50% charged

Pack needs to be charged

To actuate the fuel gauge, press and hold the fuel gauge button.

A combination of the three green LED lights will illuminate

designating the level of charge left. When the level of charge

in the battery is below the usable limit, the fuel gauge will not

illuminate and the battery will need to berecharged.

NOTE: The fuel gauge is only an indication of the charge left on

the battery pack. It does not indicate tool functionality and is

subject to variation based on product components, temperature

and end-userapplication.

Labels on Charger and Battery Pack

In addition to the pictographs used in this manual, the labels

on the charger and the battery pack may show the following

pictographs:

Read instruction manual beforeuse.

See Technical Data for chargingtime.

Do not probe with conductiveobjects.

Do not charge damaged batterypacks.

Do not expose towater.

Have defective cords replacedimmediately.

Charge only between 4 ˚C and 40 ˚C.

Only for indooruse.

Discard the battery pack with due care for

theenvironment.

10

ENGLISH

Charge STANLEYFATMAX battery packs only

with designated STANLEYFATMAX chargers.

Charging battery packs other than the

designated STANLEYFATMAX batteries with a

STANLEYFATMAX charger may make them burst or

lead to other dangeroussituations.

Do not incinerate the batterypack.

Battery Type

The SFMCMW2653 operates on 54V batterypacks.

For optimum results, use: SFMCB6025, SFMCB605, SFMCB6075

Refer to Technical Data for moreinformation.

Package Contents

The package contains:

1 Lawn mower

1 Grass Collection Bag

1 Safety Key

1 Instruction manual

NOTE: Battery packs, chargers and kitboxes are not included

with N models. Battery packs and chargers are not included with

NT models. Bmodels include Bluetooth® batterypacks.

NOTE: The Bluetooth® word mark and logos are registered

trademarks owned by the Bluetooth®, SIG, Inc. and any

use of such marks by STANLEYFATMAX is under license.

Other trademarks and trade names are those of their

respectiveowners.

• Check for damage to the tool, parts or accessories which may

have occurred duringtransport.

• Take the time to thoroughly read and understand this manual

prior tooperation.

Markings on Tool

The following pictograms are shown on the tool:

Read instruction manual beforeuse.

Wear earprotection.

Wear eyeprotection.

Beware of sharp blades. Blades continue to rotate after

the motor is switched off. Remove disabling device

beforemaintenance.

Beware of flying objects. Keep bystanders away from

the cuttingarea.

98

Directive 2000/14/EC guaranteed soundpower.

Do not expose torain.

The blades will continue to rotate after the

machine is switchedoff.

Date Code Position(Fig.A)

The date code

38

, which also includes the year of manufacture,

is printed into thehousing.

Example:

2019 XX XX

Year of Manufacture

Description(Fig.A)



WARNING: Never modify the power tool or any part of it.

Damage or personal injury couldresult.

1

ON-OFF switch box

2

ON-OFF button

3

Safety key

4

Handle

5

Bail handle

6

Handle locks

7

Handle brackets

8

Handle storage detent

holes

9

Battery port cover

10

Cut height adjust lever

11

Rear door cover

12

Grass collection bag

13

Grass collection bag

handle

14

Upper carrying handle

Intended Use

This lawn mower has been designed for professional lawn

mowingapplications.

DO NOT use under wet conditions or in presence of flammable

liquids orgases.

This lawn mower is a professional lawn careappliance.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

ASSEMBLY



DANGER: To reduce the risk of serious personal

injury, turn unit off, remove safety key, and

remove battery pack before assembly, making any

adjustments or removing/installing attachments or

accessories. An accidental start-up can causeinjury.

Adjusting Handle Height(Fig.B)

The mower is shipped in storage mode. You will need to adjust

the handle to operating position beforecontinuing.

1. To unlock the handle

4

from storage position, twist the two

handle locks

6

90°. The handle locks are located on both

sides of the handle

as shown in Fig.B

.

2. R

aise the handle to operatingposition.

3. Locate the three handle detent holes

34

located on the

handle brackets

7

as shown in Fig.B.

4. Adjust the handle to the position that best fits the operator

and lock the handle in place by twisting the handle locks

back 90° and allowing the handle locks

6

to snap into the

desired detentholes.

11

ENGLISH

Grass Collection Bag(Fig.C)



DANGER: Remove safety key and battery pack, when

opening rear door cover and installingbag.

1. Lift the rear door cover

11

and place the grass collection

bag

12

onto the mower so the bag hooks

35

rest on the

lugs

18

as shown in Fig.C. Then lower the rear doorcover.

OPERATION



DANGER: To reduce the risk of serious personal

injury, turn unit off, remove safety key, and remove

battery pack before making any adjustments or

removing/installing attachments or accessories. An

accidental start-up can causeinjury.

Installing and Removing the Battery

Pack(Fig.A, D)



DANGER: MAKE CERTAIN THE SAFETY KEY IS

REMOVED TO PREVENT ACTUATION BEFORE

REMOVING OR INSTALLINGBATTERY.

NOTE: For best results, make sure the battery pack is

fullycharged.

To Install Battery Pack

1. Lift and hold the battery port cover

9

up to expose the

battery port

19

.

2. Slide a battery pack

20

into the battery port until an

audible click is heard(Fig.D). Make sure the battery pack is

fully seated and fully latched intoposition.

3. Close the battery port cover. Ensure the cover is fully closed

before startingmower.

To Remove Battery Pack

1. Open the battery port cover

9

as describedabove.

2. Depress the battery release button

21

on the mower and

pull battery pack

20

out oftool.

READ THIS INSTRUCTION MANUAL BEFORE

OPERATING YOUR MOWER

Refer to Figure A at the beginning of this manual for a complete list

ofcomponents. Save this manual for futurereference.



DANGER: Sharp moving blade. Do not operate the

mower in mulching mode if the rear door and side

discharge door are not closed under spring tension as

serious injury could result. Take your mower to the nearest

service center forrepair.



DANGER: Do not operate mower unless handle is

locked intoposition.



DANGER:

Sharp moving blade. Never operate the

mower in bagging mode unless the bag hooks on the grass

collection bag are seated properly on the mower and the

rear discharge door rests firmly against the top of the grass

collection bag as serious injury couldresult.



WARNING: Let the mower work at its own pace. Do

notoverload.

Adjusting Mower Height(Fig.E)

The height of cut is adjusted by the cut height adjustlever.

NOTE: If you are not sure which height to cut, begin mowing

with the cut height adjustment lever

10

positioned towards

the rear of the appliance and adjust the height down as needed,

as shown in Fig.E.

To Set the Height of Cut

1. Pull the cut height adjustment lever

10

out of the locking

notch

22

.

2. Move the lever towards the rear of the appliance to raise the

height ofcut.

3. Move the lever towards the front of the appliance to lower

the height ofcut.

4. Push the height adjustment lever into one of the

lockingnotches.

Safety Key(Fig.F)



DANGER: Sharp moving blade. In order to prevent

accidental start-up or unauthorized use of your

cordless mower, a removable safety key

3

has been

incorporated into the design of your mower. The mower

will be completely disabled when the safety key has been

removed from themower.

NOTE: The safety key has a tether rope to allow for storage

on a nail, out of the reach of children. Do not tether safety key

tomower.

DANGER: Rotating blades can cause serious injury. To

prevent serious injury, remove safety key and battery pack when

unattended, or when charging, cleaning, servicing, transporting,

lifting, or storingmower.

Starting Mower(Fig.G)



DANGER: Sharp moving blade. Never attempt to

override the operation of this switch box and safety

key system as serious injury couldresult.

NOTE: Mower is operational when battery and safety key

areinstalled.

1. Insert safety key

3

into the ONOFF switch box

1

until it is

fully seated inside housing as shown in Fig.G. The mower is

nowoperational.

2. Your mower is equipped with a special ONOFF switch

box

1

. To operate the mower, push and hold the ONOFF

button

2

on the ONOFF switch box

1

, then pull the bail

handle

5

to the handlebar as shown in Fig.G. Once the

mower starts you can release theONOFFbutton.

3. To turn the mower OFF, release the bailhandle

5

.



WARNING: Never attempt to lock a switch or bail handle

in the ONposition.

NOTE: Once the bail handle has returned to the original

position it will activate the “Automatic Braking Mechanism”. The

motor is mechanically braked and the mower blade will stop

rotating in three seconds orless.

Mower Overload

To prevent damage due to overload conditions, do not try to

remove too much grass at one time. Slow down your cutting

pace, or raise the cutheight.

12

ENGLISH

Storage(Fig.A, H)



DANGER: Rotating blade can cause serious injury.

Release bail handle

5

to turn mower off, remove safety

key, and remove battery before lifting, transporting, or

storing the mower. Store in a dryplace.



CAUTION: Pinch point. To avoid being pinched, keep

fingers away from area around handle brackets when

folding downhandles.

The handle of the mower can be easily folded down for quick

and convenientstorage.

1. To unlock the handle

4

pull the two handle locks

6

,

located on both sides of the handle, and twist a quarterturn.

2. Fold the handle to the front of the mower as shown in Fig.H.

3. Locate the handle storage detent holes located on the

handle brackets

7

as shown in Fig.H.

4. Lock the handle in place by untwisting the handle locks

6

allowing them to snap into the storage detent holes and

ensure the handle is firmlylatched as shown in Fig.H.

Carrying the Mower(Fig.A, I)



DANGER: Rotating blades can cause serious injury.

To prevent serious injury, remove safety key and

battery pack when unattended, or when charging,

cleaning, servicing, transporting, lifting, or

storingmower.

The mower can be carried using the convenient carry handle

14

DO NOT attempt to lift the mower by grasping the main

handle

4

.

Mowing Tips(Fig.A)



WARNING: ALWAYS INSPECT AREA WHERE MOWER

IS TO BE USED AND REMOVE ALL STONES, STICKS,

WIRE, BONES, AND OTHER DEBRIS WHICH MIGHT BE

THROWN BY THE ROTATINGBLADE.



WARNING: Mow across the face of slopes, never up-and-

down. Exercise extreme caution when changing direction

on slopes. Do not mow excessively steep slopes. Always

maintain goodfooting.

• Release bail handle to turn mower “OFF” when crossing any

gravel area (stones can be thrown by theblade).

• Set mower at highest cutting height when mowing in rough

ground or in tall weeds. Removing too much grass at one

time can cause the motor to be overloaded and tostop.

• If a grass collection bag

12

is used during the fast growing

season, the grass may tend to clog up at the discharge

opening. Release bail handle to turn mower off, remove

the safety key and battery pack. Remove the catcher and

shake the grass down to the back end of the bag. Also clean

out any grass or debris which may be packed around the

discharge opening. Replace the grasscatcher.

• If mower should start to vibrate abnormally, release bail

handle to turn mower off, remove the safety key and battery

pack. Check immediately for cause. Vibration is a warning

of trouble. Do not operate mower until a service check has

been made. Refer to Troubleshooting Guide inthismanual.

• For best cutting results, keep blade sharpened andbalanced.

• Inspect and thoroughly clean mower after each use as a

deck with caked grass will degradeperformance.

• Always release bail handle to turn mower off, remove safety

key and battery pack when leaving it unattended even for a

short period oftime.

The following suggestions will help you to

obtain optimum run time from your cordless

mower:

• Slow down in areas where the grass is especially long

orthick.

• Avoid mowing when the grass is wet from rain or dew-

soaked.

• Cut your lawn frequently, especially during high

growthperiods.

NOTE: It is recommended that your mower be recharged after

use to prolong the battery life. Frequent charging will not harm

your battery, and will ensure that the battery is fully charged

and ready for its next use. Storing battery not fully charged will

shorten batterylife.

MAINTENANCE



DANGER: To reduce the risk of serious personal

injury, turn unit off, remove safety key, and remove

battery packs before making any adjustments or

removing/installing attachments or accessories. An

accidental start-up can causeinjury.

Removing and Installing Blade(Fig.J–L)



DANGER: RISK OF INJURY. WHEN REASSEMBLING

THE BLADE SYSTEM, ENSURE EACH PART IS REINSTALLED

CORRECTLY, AS DESCRIBED BELOW. IMPROPER ASSEMBLY

OF THE BLADE OR OTHER PARTS OF THE BLADE SYSTEM

MAY CAUSE SERIOUSINJURY.



DANGER: To reduce the risk of serious personal

injury, turn unit off, remove safety key, and remove

battery pack before making any adjustments or

removing/installing attachments or accessories. An

accidental start-up can causeinjury.

1. Cut a piece of 2" x 4" wood

23

(about 2 feet long) (610mm)

to keep blade from turning when removing the flange

nut

24

.



WARNING: Use gloves and proper eye protection. Turn the

mower on its side. Be careful of sharp edges ofblade.

2. Position wood and unscrew flange nut

24

counterclockwise

with a 18 mm wrench

25

as shown in Fig.J.

3. Remove square metal blade spacer

26

, square plastic blade

insulator

27

and blade

28

as shown in Fig.K. The blade

fan

29

should not be removed. Examine all pieces for

damage and replace ifnecessary.

4. Install sharpened or new (STZMW353) blade

28

on

shoulder

30

of the blade fan as shown in Fig.K.

NOTE: When replacing sharpened or new blade on shoulderof

blade fan, make sure the “GRASS SIDE” on the blade will be

facing the ground when the mower is returned to its normal

uprightposition.

13

ENGLISH

5. Install the plastic blade insulator

27

on the blade such that

the raised lips on one side engage the edges of theblade.

6. Install the blade spacer

26

so that it sits inside the raised

lips on the other side of the blade insulator. Be sure to align

the flats in the hole of the blade spacer with the flats of

the shaft, rotating the blade and blade insulator together

asnecessary.

7. Position piece of wood to keep blade from turning as shown

in Fig.L. Install flange nut

24

with the flange against the

blade spacer

26

and securely tighten the blade

28

with a

wrench

25

.

Blade Sharpening

KEEP BLADE SHARP FOR BEST MOWER PERFORMANCE. A DULL

BLADE DOES NOT CUT GRASSCLEANLY.



WARNING: Use gloves and proper eye protection while

removing, sharpening, and installing blade. Ensure that

safety key and battery pack areremoved.

Sharpening the blade twice during a mowing season is usually

sufficient under normal circumstances. Sand causes the blade

to dull quickly. If your lawn has sandy soil, more frequent

sharpening may berequired. REPLACE BENT OR DAMAGED

BLADEIMMEDIATELY.

When Sharpening the Blade

• Make sure blade remainsbalanced.

• Sharpen blade at the original cuttingangle.

• Sharpen cutting edges on both ends of blade, removing

equal amounts of material from bothends.

To Sharpen Blade in a Vise(Fig.M)

1. Be sure the bail handle is released, the blade has stopped

and safety key and battery pack are removed before

removing theblade.

2. Remove blade from mower. See instructions for Removing

and InstallingBlade.

3. Secure blade

28

in a vise

31

.

4. Wear proper eye protection and gloves and be careful not

to cutyourself.

5. Carefully file the cutting edges of the blade with a fine tooth

file

32

or sharpening stone, maintaining the angle of the

original cuttingedge.

6. Check balance of blade. See instructions for

BladeBalancing.

7. Replace blade on mower and tightensecurely.

Blade Balancing(Fig.N)

Check balance of the blade

28

by placing center hole in the

blade over a nail or round screwdriver

33

, clamped horizontally

in a vise

31

. If either end of the blade rotates downward, file

along the sharp edge of that dropping end. Blade is properly

balanced when neither enddrops.

Lubrication

No lubrication is necessary. Do not oil the wheels. They have

plastic bearing surfaces which require nolubrication.

Cleaning

Release bail handle

5

to turn mower off, let the blade come to a

stop and then remove safety key. Clean out any clippings which

may have accumulated on the underside of the deck. After

several uses, check all exposed fasteners fortightness.



WARNING: Blow dirt and dust out of the main housing

with dry air as often as dirt is seen collecting in and around

the air vents. Wear approved eye protection and approved

dust mask when performing thisprocedure.



WARNING: Never use solvents or other harsh chemicals

for cleaning the non-metallic parts of the tool. These

chemicals may weaken the materials used in these parts.

Use a cloth dampened only with water and mild soap.

Never let any liquid get inside the tool; never immerse any

part of the tool into aliquid.

Release bail handle

5

to turn mower off, let the blade come

to a stop and then remove battery and safety key. Clean out

any clippings which may have accumulated on the underside

of the deck. After several uses, check all exposed fasteners

fortightness.

Corrosion

Fertilizers and other garden chemicals contain agents which

greatly accelerate the corrosion of metals. If you mow in areas

where fertilizers or chemicals have been used, the mower

should be cleaned immediately afterward as follows:

Release bail handle

5

to turn mower off and remove battery

and safety key. Wipe all exposed parts with a dampcloth.



CAUTION: Do not pour or spray water on the mower

in an attempt to clean IT. Do not store the tool on or

adjacent to fertilizers or chemicals. Such storage can cause

rapidcorrosion.

Optional Accessories



WARNING: Since accessories, other than those offered by

STANLEYFATMAX, have not been tested with this product,

use of such accessories with this tool could be hazardous.

To reduce the risk of injury, only STANLEYFATMAX

recommended accessories should be used with

thisproduct.

Consult your dealer for further information on the

appropriateaccessories.

Protecting the Environment

Separate collection. Products and batteries marked

with this symbol must not be disposed of with normal

householdwaste.

Products and batteries contain materials that can

be recovered or recycled reducing the demand for raw

materials. Please recycle electrical products and batteries

according to local provisions. Further information is available at

www.2helpU.com.

14

ENGLISH

Rechargeable Battery Pack

This long life battery pack must be recharged when it fails to

produce sufficient power on jobs which were easily done before.

At the end of its technical life, discard it with due care for our

environment:

• Run the battery pack down completely, then remove it from

thetool.

• Li-Ion cells are recyclable. Take them to your dealer or a

local recycling station. The collected battery packs will be

recycled or disposed ofproperly.

Guarantee

1 Year Guarantee

All STANLEY FATMAX power tool products include a 1 year

guarantee as standard. In the unlikely event that your powertool

becomes defective due to faulty materials or worksmanship

within 1 year of purchase, STANLEY guarantees to replace or

repair all defective parts free of charge, or – at our discretion –

replace the item free ofcharge.

3 Year Guarantee

Register your STANLEY FATMAX power tool within 4 weeks

of purchase and qualify for an additional 2 year guarantee.

Having registered your power tool, in the unlikely event that

your powertool becomes defective due to faulty materials or

worksmanship, STANLEY guarantees to replace or repair all

defective parts free of charge, or – at our discretion – replace the

item free ofcharge.

TROUBLESHOOTING

If your appliance seems not to operate properly, follow the

instructions below. If this does not solve the problem, please

contact your local STANLEYFATMAX repairagent.



WARNING: Before proceeding, release the bail bar to turn

mower off and wait for the blade tostop.

Problem Possible Solution

Mower doesn’t run

when bail handle

is activated

Check to make sure mower battery is properly

installed and that the button on switch box is

being completely depressed before pulling the

bail handle.

Release bail handle to turn mower off. Remove

safety key and battery pack, turn mower over and

check that blade is free to turn.

Check that the battery cavity is free of debris and is

connected properly.

Has battery been fully charged? Press state of

charge button.

Motor stops

while mowing

Release bail handle to turn mower off. Remove

safety key and battery pack Turn mower over and

check that blade is free to turn.

Raise cutting height of wheels to highest position

and start mower.

Check that the battery cavity is free of debris and is

connected properly

Has battery been fully charged? Press state of

charge button

Avoid overloading the mower. Slow down the

cutting pace, or raise the cut height.

Mower runs but

cutting performance

is unsatisfactory

Release bail handle to turn mower off. Uninstall

power source. Turn mower over and check:

• Blade for sharpness - Keep blade sharp.

• Deck and discharge chute for clogging.

Wheel height adjustment may be set too low for

grass condition. Raise cutting height.

Mower is too hard

to push

Release bail handle to turn mower off. Uninstall

power source. Raise cutting height to reduce deck

drag on grass. Check each wheel for free rotation.

Mower is abnormally

noisy and vibrates

Release bail handle to turn mower off. Uninstall

power source. Turn mower on side and check blade

to ensure it has not been bent or damaged. If blade

is damaged, replace with a STANLEY FATMAX

replacement blade. If the underside of the deck is

damaged, return mower to a STANLEY FATMAX

Authorised service centre.

If there is no visible damage to the blade and the

mower still vibrates:

• Release bail handle to turn mower off.

• Unplug mower.

• Disassemble entire blade assembly as

described in the Removing and installing

blade section.

• Remove any debris and clean each piece.

• Replace each piece as described in the

Removing and installing blade section.

If mower still vibrates, return the mower to an

authorised STANLEY FATMAX service center.

15

ENGLISH

Problem Possible Solution

Battery charger LEDs

not on

Check plug connection.

Replace charger.

Mower not picking up

clippings with bag

Chute clogged. Release bail handle to turn

mower off. Uninstall power source. Clear chute of

grass clippings.

Raise cutting height of wheels to shorten length

of the cut.

Bag full. Empty bag more often.

16

DEUTSCH

Akku Katalognr. Ausgangsspannung Ah

Ladegerät

SFMCB6012

SFMCB6025 54 2,5 X

SFMCB605 54 5 X

SFMCB6075 54 7,5 X

"X" Zeigt an, dass der Akku mit diesem speziellen Ladegerät

kompatibel ist. Lesen Sie die Betriebsanleitung für

genauereInformationen.

EG-Konformitätserklärung

Maschinenrichtlinie

Rasenmäher

SFMCMW2653

STANLEYFATMAX erklärt, dass diese unter Technische Daten

beschriebenen Geräte übereinstimmen mit:

2006/42/EC, EN60335-1:2012 + A11:2014, EN60335-2-77:2010.

Diese Produkte erfüllen auch die Richtlinie 2014/30/EU und

2011/65/EU. Für weitere Informationen wenden Sie sich bitte an

STANLEYFATMAX unter der folgenden Adresse oder schauen

Sie auf der Rückseite dieser Betriebsanleitungnach.

Der Unterzeichnete ist verantwortlich für die Zusammenstellung

des technischen Dossiers und gibt diese Erklärung im Namen

von STANLEYFATMAXab.

2000/14/EC, Rasenmäher, 50<L≤70cm, Annex VI, DEKRA

Certification B.V., Meander 1051 / P.O. Box 5185

6825 MJ ARNHEM / 6802 ED ARNHEM, Niederlande

Kennnummer der benannten Stelle: 0344

Schallpegel gemäß 2000/14/EC (Artikel12, AnhangIII, 50 <L ≤

70 cm):

L

PA

(Emissionsschalldruck) 78,0 dB(A)

Unsicherheitsfaktor (K) = 1,4 dB(A)

L

WA

(garantierte Schallleistung) 98 dB(A)

A. P. Smith

Technical Director

STANLEYFATMAX Europe, Egide Walschaertsstraat 14-18,

2800 Mechelen, Belgien

2019-10-11

WARNUNG: Zur Reduzierung der Verletzungsgefahr bitte

die Betriebsanleitunglesen.

Herzlichen Glückwunsch!

Sie haben sich für ein Gerät von STANLEYFATMAX entschieden.

Langjährige Erfahrung, sorgfältige Produktentwicklung und

Innovation machen STANLEYFATMAX zu einem zuverlässigen

Partner für professionelle Anwender vonElektrowerkzeugen.

Technische Daten

SFMCMW2653

Spannung V

DC

54

Typ 1

Batterietyp Li-Ion

Leerlaufdrehzahl U/min 3300

Messerlänge cm 51

Gewicht (ohne Akku) kg 33

Lärmwerte und Vibrationswerte (Triax-Vektorsumme) gemäß EN60335:

L

PA

(Emissions-Schalldruckpegel) dB(A) 78,0

L

WA

(Schallleistungspegel) dB(A) 91,5

K (Unsicherheit für den angegebenen

Schallpegel)

dB(A) 0,8

Gewichteter Hand-Arm-Vibrationswert:

Vibrationsemissionswert a

h

= m/s² <2,5

Messungenauigkeit K = m/s² 1,5

Der in diesem Informationsblatt angegebene

Vibrationsemissionswert wurde gemäß einem standardisierten

Test laut EN60335 gemessen und kann für einen Vergleich

zwischen zwei Geräten verwendet werden. Er kann zu einer

vorläufigen Einschätzung der Exposition verwendetwerden.



WARNUNG: Der angegebene Vibrationsemissionswert

bezieht sich auf die Hauptanwendung des Gerätes.

Wenn das Gerät jedoch für andere Anwendungen, mit

anderem Zubehör oder schlecht gewartet eingesetzt

wird, kann die Vibrationsemission verschieden sein. Dies

kann den Expositionsgrad über die Gesamtbetriebszeit

erheblicherhöhen.

Eine Schätzung der Vibrationsstärke sollte auch

berücksichtigen, wie oft das Gerät ausgeschaltet

wird oder über welche Zeit es zwar läuft, aber nicht

wirklich in Betrieb ist. Dies kann die Exposition über die

Gesamtbetriebszeit erheblichmindern.

Identifizieren Sie zusätzliche Sicherheitsmaßnahmen,

um den Bediener vor den Vibrationsauswirkungen zu

schützen, wie: Erhalt des Werkzeugs und Zubehörs, Hände

warm halten, Organisation vonArbeitsmustern.

54V-RASENMÄHER

SFMCMW2653

Deutsch (übersetzt von den originalanweisungen)

17

DEUTSCH

• Verwenden Sie das Gerät nur in trockener Umgebung. Achten

Sie darauf, dass das Gerät nicht nasswird.

• Tauchen Sie das Gerät nicht inWasser.

• Versuchen Sie nicht, das Gehäuse zu öffnen. Es gibt keine vom

Benutzer zu wartenden Teile im Inneren desLasers.

• Betreiben Sie das Gerät nicht in explosionsgefährdeter

Umgebung, in der sich brennbare Flüssigkeiten, Gase oder

Staubbefinden.

• Überzeugen Sie sich vor der Verwendung, dass Mähmesser,

Messerschrauben und Mäheinheit weder abgenutzt

noch beschädigt sind. Ersetzen Sie bei abgenutzten oder

beschädigten Messern und Schrauben den entsprechenden

Satz, sodass nicht neue und alte Komponenten gleichzeitig

verwendetwerden.

• Es sollte stets ein Sicherheitsabstand zu anderen Personen,

insbesondere Kindern, und Haustieren eingehaltenwerden.

• Beachten Sie, dass der Bediener bzw. Benutzer für eventuelle

Personen- oder Sachschäden verantwortlichist.

Vor der Verwendung

• Tragen Sie stets feste Schuhe und eine lange Hose, wenn Sie

mit dem Gerät arbeiten. Betreiben Sie die Maschine nicht

barfuß oder mit offenen Sandalen. Vermeiden Sie das Tragen

von Kleidung, die locker sitzt oder herabhängende Schnüre,

Bänder o.ä.besitzt.

• Kontrollieren Sie stets den Bereich, in dem das Gerät verwendet

werden soll, und entfernen Sie alle Gegenstände, die von dem

Gerät umhergeschleudert werdenkönnen.

• Überzeugen Sie sich vor der Verwendung, dass Mähmesser,

Messerschraube und Mäheinheit weder abgenutzt noch

beschädigt sind. Ersetzen Sie abgenutzte oder beschädigte

Teile in Sätzen, um die Ausgewogenheit der Maschine zu

bewahren. Ersetzen Sie beschädigte oder unlesbareEtiketten.

Nach dem Gebrauch

• Bewahren Sie das Gerät bei Nichtgebrauch an einem

trockenen, gut belüfteten Ort außerhalb der Reichweite von

Kindernauf.

• Kinder sollten keinen Zugang zu aufbewahren Gerätenhaben.

• Wenn das Gerät in einem Fahrzeug transportiert oder gelagert

wird, bewahren Sie es im Kofferraum oder einer geeigneten

Ablage auf, damit es bei plötzlichen Geschwindigkeits- oder

Richtungsänderungen nicht in Bewegung geratenkann.

Inspektion und Reparaturen

• Prüfen Sie das Gerät vor der Verwendung auf beschädigte

oder defekte Teile. Prüfen Sie, ob Teile gebrochen sind, Schalter

beschädigt wurden oder andere Bedingungen vorliegen, die

die Funktion beeinträchtigenkönnen.

• Betreiben Sie das Gerät nicht, wenn Teile beschädigt oder

defektsind.

• Lassen Sie beschädigte oder defekte Teile in einer

Vertragswerkstatt reparieren oderaustauschen.

• Ersetzen oder entfernen Sie keine Teile, für die in dieser

Anleitung keine entsprechende Beschreibung enthaltenist.

Definitionen: Sicherheitsrichtlinien

Im Folgenden wird die Relevanz der einzelnen Warnhinweise

erklärt. Bitte lesen Sie die Betriebsanleitung und achten Sie auf

dieseSymbole.



VORSICHT: Weist auf eine unmittelbar drohende

gefährliche Situation hin, die, sofern nicht vermieden,

zu tödlichen oder schweren Verletzungen führenwird.



WARNUNG: Weist auf eine möglicherweise gefährliche

Situation hin, die, sofern nicht vermieden, zu tödlichen

oder schweren Verletzungen führenkann.



VORSICHT: Weist auf eine möglicherweise gefährliche

Situation hin, die, sofern nicht vermieden, zu leichten

oder mittelschweren Verletzungen führenkann.

HINWEIS: Weist auf ein Verhalten hin, das nichts mit

Verletzungen zu tun hat, aber, wenn es nicht vermieden

wird, zu Sachschäden führenkann.



Weist auf ein Stromschlagrisikohin.



Weist auf eine Brandgefahrhin.

Sicherheitshinweise



WARNUNG: Beachten Sie beim Umgang mit kabellosen

Geräten stets die grundlegenden Sicherheitshinweise, die

im Folgenden beschrieben werden. Dadurch verhindern Sie

Brände, Stromschläge sowie Sach- undPersonenschäden.



WARNUNG: Beachten Sie beim Verwenden des Geräts

unbedingt die Sicherheitsregeln. Lesen Sie zu Ihrer eigenen

Sicherheit und zum Schutz in der Nähe befindlicher

Personen vor Gebrauch des Geräts die folgende

Bedienungsanleitung. Heben Sie diese Anleitung zur

späteren Verwendung gutauf.

• Lesen Sie diese Anleitung vollständig und aufmerksam

durch, bevor Sie das Gerätverwenden.

• Der vorgesehene Verwendungszweck ist in dieser

Anleitung beschrieben. Bei Verwendung von Zubehör

oder Anbauteilen, die nicht in dieser Anleitung

empfohlen werden, sowie bei der Verwendung des

Geräts in Abweichung von den in dieser Anleitung

beschriebenen Verfahren bestehtVerletzungsgefahr.

• Bewahren Sie diese Anleitungauf.

BEWAHREN SIE ALLE WARNHINWEISE

UND ALLE ANWEISUNGEN AUF

Verwendung des Geräts

Verwenden Sie das Gerät stets mitUmsicht.

• Das Gerät ist nicht für die unbeaufsichtigte Verwendung durch

Kinder oder gebrechliche Personenvorgesehen.

• Das Gerät ist keinSpielzeug.

• Achten Sie darauf, dass sich im Arbeitsbereich keine Kinder

oder Tiere aufhalten. Verhindern Sie, dass Kinder das

Gerätberühren.

• Seien Sie besonders vorsichtig, wenn Sie das Gerät in der Nähe

von Kindernverwenden.

18

DEUTSCH

• Gehen Sie bei Einstellungen am Rasenmäher vorsichtig vor,

um zu verhindern, dass Ihre Finger zwischen den beweglichen

Messern/Teilen und feststehenden Teilen des Geräts

eingeklemmtwerden.

• Beachten Sie bei Wartungsarbeiten an den Messern, dass sich

diese auch ohne Stromversorgungbewegen.

Zusätzliche Sicherheitshinweise für

Rasenmäher

• Transportieren Sie die Maschine nicht, während die

Stromversorgungläuft.

• Halten Sie den Rasenmäher während des Betriebs sicher mit

beiden Händenfest.

• Halten Sie beide Hände in der Betriebsposition, wenn

der Rasenmäher gekippt werden muss. Halten Sie beide

Hände in der Betriebsposition bis der Rasenmäher wieder

ordnungsgemäß auf dem Boden abgestelltwurde.

• Tragen Sie beim Rasenmähen keine Kopfhörer

zumMusikhören.

• Passen Sie niemals die Höhe der Räder an, während der Motor

läuft oder sich der Sicherheitsschlüssel im Schlossbefindet.

• Lassen Sie den Bügelschalter los, um den Rasenmäher

auszuschalten, wenn dieser blockiert. Warten Sie, bis das

Messer zum Stillstand gekommen ist, bevor Sie versuchen,

die Verstopfung zu beseitigen oder Gegenstände von der

Unterseite zuentfernen.

• Halten Sie Hände und Füße vom Schnittbereichfern.

• Halten Sie die Sägeblätter scharf. Tragen Sie beim Umgang mit

dem Messer des Rasenmähers stetsSchutzhandschuhe.

• Wenn der Grasfangbehälter verwendet wird, muss dieser

regelmäßig auf Abnutzungen und Beschädigungen

überprüft werden. Wechseln Sie aus Sicherheitsgründen den

Grasfangbehälter bei starker Abnutzungaus.

• Seien Sie besonders vorsichtig, wenn Sie den Rasenmäher

wenden oder in Ihre Richtungziehen.

• Bringen Sie Hände oder Füße nicht in die Nähe bzw. unter den

Rasenmäher. Halten Sie jederzeit einen Sicherheitsabstand

zurAuswurföffnung.

• Entfernen Sie Steine, Äste, Drähte, Spielzeuge, Knochen usw.,

die in das Messer geraten könnten, aus dem Bereich, in dem

der Rasenmäher verwendet wird. Objekte, die in das Messer

geraten, können ernsthafte Verletzungen verursachen. Bleiben

Sie hinter dem Griff, wenn der Motorläuft.

• Betreiben Sie den Rasenmäher weder barfuß noch mit

Sandalen. Tragen Sie jederzeit festesSchuhwerk.

• Ziehen Sie den nur Rasenmäher nur rückwärts, wenn dies

unbedingt erforderlich ist. Achten Sie stets auf den Boden

und den Bereich hinter Ihnen, bevor und während Sie sich

rückwärtsbewegen.

• Achten Sie darauf, dass das Material nicht in Richtung

von Personen ausgeworfen wird. Achten Sie darauf,

dass das Material nicht in Richtung von Wänden oder

anderen Gegenständen ausgeworfen wird. Das Material

kann gegen den Bediener zurückgeschleudert werden.

Lassen Sie den Bügelschalter los, und warten Sie, bis

das Messer zum Stillstand gekommen ist, bevor Sie

Kiesoberflächenüberqueren.

• Betreiben Sie den Rasenmäher nicht ohne angebrachten und

intakten Grasfangbehälter, Auswurfschutz, hinteren Schutz

und andere Schutzvorrichtungen. Überprüfen Sie regelmäßig

alle Schutz- und Sicherheitsvorrichtungen auf deren

ordnungsgemäße Funktion. Ersetzen Sie beschädigte Schutz-

und Sicherheitsvorrichtungen vor der weiterenVerwendung.

• Lassen Sie den eingeschalteten Rasenmäher

niemalsunbeaufsichtigt.

• Lassen Sie stets den Bügelgriff los, warten Sie, bis das Messer

zum Stillstand gekommen ist, wenn Sie den Rasenmäher

reinigen, den Grasfangbeutel entfernen, Verstopfungen aus der

Auswurföffnung beseitigen, den Rasenmäher unbeaufsichtigt

lassen bzw. Anpassungen vornehmen oder Reparaturen und

Inspektionenausführen.

• Betreiben Sie den Rasenmäher nur bei Tageslicht oder bei

ausreichender Beleuchtung, sodass Gegenstände auf dem

Schnittweg vom Betriebsbereich des Rasenmähers aus

deutlich sichtbarsind.

• Betätigen Sie den Rasenmäher nicht, wenn Sie unter Alkohol-

oder Drogeneinfluss stehen oder wenn Sie müde oder krank

sind. Bleiben Sie immer aufmerksam, achten Sie darauf, was

Sie tun und setzen Sie den gesunden Menschenverstandein.

• Meiden Sie gefährliche Umgebungen. Betreiben Sie den

Rasenmäher nicht in feuchtem oder nassem Gras. Verwenden

Sie den Rasenmäher keinesfalls im Regen. Achten Sie

auf Trittsicherheit. Betreiben Sie das Gerät nur im Gehen,

nierennend.

• Lassen Sie den Bügelschalter los, warten Sie, bis das Messer

zum Stillstand gekommen ist, wenn Sie ungewöhnliche

Vibrationen des Rasenmähers bemerken, und prüfen Sie die

Ursache. Im Allgemeinen deutet Vibration auf ein Problem hin.

Im Fall einer ungewöhnlichen Vibration des Geräts finden Sie

unter „Problembehebung“ weitereInformationen.

• Tragen Sie beim Betreiben des Rasenmähers stets geeigneten

Augen- undAtemschutz.

• Der Gebrauch von Zubehörteilen oder Zusätzen, die nicht für

den Gebrauch mit dem Rasenmäher empfohlen werden, kann

gefährlich sein. Verwenden Sie nur von STANLEYFATMAX

genehmigtesZubehör.

• Beugen Sie sich nicht zu weit nach vorne, wenn Sie den

Rasenmäher betreiben. Achten Sie während des Betriebs

des Rasenmähers stets auf Ihre Standfestigkeit und

IhrGleichgewicht.

• Mähen Sie stets parallel zum Hang, nie den Hang hinauf oder

hinunter. Gehen Sie mit äußerster Vorsicht vor, wenn Sie an

Hängen die Richtungwechseln.

• Achten Sie auf Löcher, Wurzeln, Bodenunebenheiten,

Steine und andere verborgene Objekte. Unebenes Gelände

kann zu Unfällen durch Stürze führen. Hohes Gras kann

Hindernisseverbergen.

La page charge ...

Stanley SFMCMW2653B Le manuel du propriétaire

Ce manuel convient également à

Stanley SFMCMW2653B Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents