Onelink 1042136 Manuel utilisateur

User’s Manual Model: 1042136

Important! Please read carefully and save this document.

This user’s manual contains important information about your combination Smoke and CO Alarm’s operation.

If you are installing this alarm for use by others, you must leave this manual (or a copy of it) with the end user.

Installed On

Replace by

2

Table of Contents

Welcome 3

Parts of this Alarm 4

Understanding Your Alarm 5

Where to Install 6 - 7

Where Not to Install 8

Setup and Installation 9

Wireless Interconnect 10

When the Alarm Sounds 10 - 11

Using the Silence Feature 11 - 12

Weekly Testing 12

Regular Maintenance 13 - 14

Alarm End of Life 14

Ionization and Photoelectric Technology 14 - 15

Fire Safety Tips 15 - 16

What You Need to Know About CO 16 - 17

Potential Sources of CO in the Home 17 - 18

Regulatory Information 18 - 21

Special Compliance 21 - 23

General Limitations 23 - 24

Troubleshooting Guide 25

Limited Warranty 26

Copyright and Technical Speciﬁcations 27

3

Welcome

Thank you for choosing Onelink by First Alert for your safety needs. In addition to

the alarm sounds, you can receive notiﬁcations in case of an emergency to help

provide a warning of a ﬁre or carbon monoxide leak while you are home or away.

Please take time to read this manual and make this alarm an integral part of your

family’s safety plan. Visit www.onelink.ﬁrstalert.com for additional information.

Contents

Smoke and

CO Alarm

Mounting

Bracket

Mounting

Hardware

User’s

Manual

System Requirements

Wireless Network Android or iOS Device Onelink App

Required to use a 2.4 GHz wireless

connection and a compatible

802.11 b/g/n/ac router.

HomeKit

™

requires an iPhone

®

, iPad

®

,

or iPod touch

®

with iOS 10 or later,

or Android

®

5 or later.

Search and download the

Onelink Home app from the

App Store or Google Play.

4

Parts of this Alarm

1. Test/Silence Button

2. Color Indicator Ring

3. Speaker

4. Battery Drawer

1

2

5. Mounting Bracket

6. Mounting Slots

7. Turn Alarm Clockwise

to Attach

8. Turn Alarm

Counterclockwise

to Remove

5

8

7

6

3

4

5

Understanding Your Alarm

LED Color

Patterns

Smoke / CO Events Voice Guide

Power Up and Welcome

Power Up

“First Alert welcomes you to your Onelink Smoke

and Carbon Monoxide Alarm. The Onelink App will

guide you through the simple setup process.”

Programming, Silencing & Pairing “[Location, example: “Hallway”] Location Programmed.”

Testing “The testing is complete. The test is done and you are protected.”

Emergency [voice complete]

Pairing Alarm will ﬂash blue during pairing.

Testing

“Testing Smoke” [beep beep beep!]

“Testing Carbon Monoxide” [beep beep beep beep!]

“Evacuate, Evacuate, there’s Fire in the [Location]!”

“Testing Alarms... The alarm will sound and for your

protection is very loud. This may take a few seconds.”

“Highest carbon monoxide level was 0 PPM.”

Emergency

“Evacuate! Evacuate! There is Smoke [or Carbon

Monoxide] in the [Location!]!”

“Highest carbon monoxide level was [Number] PPM.”

Malfunction

“Detector error.”

“Alarm has reached its End of Life. Replace Alarm in [Location].”

Low Battery Information available via mobile app.

6

Where to Install

Minimum coverage for Smoke Alarms, as recommended by the National Fire Protection Association

(NFPA), is one Smoke Alarm on every ﬂoor, in every sleeping area, and in every bedroom (See

“Regulatory Information For Smoke Alarms” for details on the NFPA recommendations). For CO Alarms,

the National Fire Protection Association (NFPA) recommends that a CO Alarm should be centrally

located outside of each separate sleeping area in the immediate vicinity of the bedrooms. For added

protection, install additional CO Alarms in each separate bedroom, and on every level of your home.

NOTE: For added protection, install an additional Smoke/CO Alarm at least 15 feet (4.6 meters)

away from the furnace or fuel burning heat source where possible. In smaller homes or in

manufactured homes where this distance cannot be maintained, install the Alarm as far away as

possible from the furnace or other fuel burning source. Installing the Alarm closer than 15 feet

(4.6 meters) will not harm the Alarm, but may increase the frequency of unwanted alarms.

In general, install combination Smoke and Carbon Monoxide Alarms:

• On every level of your home, including ﬁnished attics and basements.

• Inside every bedroom, especially if people sleep with the door partly or completely closed.

• In the hall near every sleeping area. If your home has multiple sleeping areas, install a unit

in each. If a hall is more than 40 feet (12 meters) long, install a unit at each end.

• At the top of ﬁrst-to-second ﬂoor stairs.

• At the bottom of the basement stairs.

• For additional coverage, install Alarms in all rooms, halls, and storage areas, where

temperatures normally remain between 40˚ F and 100˚ F (4.4˚ C and 37.8˚ C).

Recommended Placement

• When installing on the wall, the top edge of Smoke Alarms should be placed between 4 inches

(102 mm) and 6 inches (153 mm) from the wall/ceiling line.

• When installing on the ceiling, place the alarm as close to the center as possible.

• In either case, install at least 4 inches (102 mm) from where the wall and ceiling meet.

• Avoid “Dead Air” spaces.

NOTE: For any location, make sure no door or other obstruction could keep carbon monoxide or smoke

from reaching the Alarm.

Installing Smoke/CO Alarms in Mobile Homes

For minimum security install one Smoke/CO Alarm as close to each sleeping area as possible.

For more security, put one unit in each room. Many older mobile homes (especially those built

before 1978) have little or no insulation. If your mobile home is not well insulated, or if you are

unsure of the amount of insulation, it is important to install units on inside walls only.

7

Where to Install (Continued)

SPEAKER OPENING

IN UPPER LEFT

CORNER

PLACE HERE

OR HERE

DO NOT PLACE

IN THIS AREA

4”

(102 mm)

minimum

between 4”- 6”

(102 mm - 153 mm)

from ceiling

CEILING

WALL

8

Where Not to Install

Do NOT locate this Smoke/CO Alarm:

• In garages, furnace rooms, crawl spaces and unﬁnished attics. Avoid extremely dusty, dirty or greasy areas.

• Where combustion particles are produced. Combustion particles form when something burns. Areas

to avoid include poorly ventilated kitchens, garages, and furnace rooms. Keep units at least 20 feet (6

meters) from the sources of combustion particles (stove, furnace, water heater, space heater) if possible.

In areas where a 20 foot (6 meter) distance is not possible – in modular, mobile, or smaller homes, for

example – it is recommended the Smoke Alarm be placed as far from these fuel-burning sources as

possible. The placement recommendations are intended to keep these Alarms at a reasonable distance

from a fuel-burning source, and thus reduce “unwanted” alarms. Unwanted alarms can occur if a Smoke

Alarm is placed directly next to a fuel-burning source. Ventilate these areas as much as possible.

• Within 5 feet (1.5 meters) of any cooking appliance. In air streams near kitchens. Air currents

can draw cooking smoke into the smoke sensor and cause unwanted alarms.

• In extremely humid areas. This Alarm should be at least 10 feet (3 meters) from a shower, sauna,

humidiﬁer, vaporizer, dishwasher, laundry room, utility room, or other source of high humidity.

• In direct sunlight.

• In turbulent air, near ceiling fans or open windows. Blowing air may prevent CO/smoke from reaching

the sensors.

• In areas where temperature is colder than 40˚ F (4.4˚C) or hotter than 100˚ F (37.8˚C). These areas include

non air conditioned crawl spaces, unﬁnished attics, uninsulated or poorly insulated ceilings, porches,

and garages.

• In insect infested areas. Insects can clog the openings to sensing chamber.

• Less than 12 inches (305 mm) away from ﬂuorescent lights. Electrical “noise” can interfere with the sensor.

• In “dead air” spaces. See below for additional information.

• “Dead air” spaces may prevent smoke from reaching the Smoke/CO Alarm. To avoid dead air spaces, follow

installation recommendations below.

• On ceilings, install Smoke/CO Alarms as close to the center of the ceiling as possible. If this is not possible,

install the Smoke/CO Alarm at least 4 inches (102 mm) from the wall or corner.

• For wall mounting (if allowed by building codes), the top edge of Smoke/CO Alarms should be placed

between 4 inches (102 mm) and 12 inches (305 mm) from the wall/ceiling line, below typical“dead air”spaces.

• On a peaked, gabled, or cathedral ceiling, install ﬁrst Smoke/CO Alarm within 3 feet (0.9 meters) of the

peak of the ceiling, measured horizontally. Additional Smoke/CO Alarms maybe required depending on

the length, angle, etc. of the ceiling’s slope. Refer to NFPA 72 for details on requirements for sloped

or peaked ceilings.

9

Setup & Installation

Do not install this unit over an electrical junction box. Air currents around junction boxes

can prevent smoke from reaching the sensing chamber and prevent the unit from alarming.

Only AC powered units are intended for installation over junction boxes.

NOTE: Be sure to mount the product in the orientation speciﬁed in the next steps as this provides the most

stability for mounting the product to the wall or ceiling. When wall mounting, it is suggested that the horn

opening is in the upper left corner. This alarm is designed to be mounted on the ceiling or wall if necessary.

Ensure the iOS software is updated to iOS 10 or later or Android 5 or later.

Step 1

Download the free Onelink app from the App Store

or Google Play and follow setup instructions.

Speaker

Opening

Step 2

Hold the mounting bracket against the ceiling (or

wall) so the two universal mounting holes are aligned

approximately at the 9 and 3 o’clock positions.

(See image). Trace around the holes with a pencil.

Step 3

Put the unit where it won’t get covered with

dust when you drill the mounting holes.

Step 4

Using a 3/16” (5 mm) drill bit, drill a hole through

the center of the outlines you traced.

Step 5

Insert the plastic screw anchors (in the plastic

bag with screws) into the holes. Tap the screw

anchors gently with a hammer, if necessary,

until they are ﬂush with the ceiling or wall.

Step 6

Install the screws but do not tighten completely. Attach the mounting bracket by aligning

the screws in the open portion of the universal mounting slots and rotating the bracket into

place. Tighten the screws until they are snug to secure the bracket. Do not over tighten.

Step 7

Mount alarm to mounting bracket to activate the alarm.

NOTE: After you activate the Alarm, the Color Indicator Ring will power up and the Alarm will

welcome you. To program your alarm, follow the instructions provided in the Onelink app.

!

WARNING: iOS and Android device notiﬁcations require a functional Wireless connection. For

best results, recommended to use with a 802.11 b/g/n router. The notiﬁcations are only as reliable as

your Wireless network and are not a substitute for a third party emergency monitoring service.

10

Wireless Interconnect

Beneﬁts of Wireless Interconnect

The wireless interconnect feature on this alarm allows you to connect each of your

First Alert Onelink alarms so when one alarm sounds, they all will sound.

!

WARNING: Install alarms and test to assure range and

reliability of interconnection throughout the house.

• First Alert Onelink alarms can typically communicate with each other if they’re 50ft (15m) apart inside a

home. Keep in mind that some features of a home may reduce the interconnect range and reliability of

interconnection, including the number of ﬂoors, number/size of rooms, furniture, type of building material,

suspended ceilings, ductwork, large metallic appliances and metal studs. This kind of interference may be

ﬁxed by adding more Onelink alarms that can route wireless signals around any various obstructions.

• Make sure you test your Onelink alarms for proper interconnection via the weekly testing.

Wireless Frequency: This alarm supports wireless frequency of 2.4Ghz b/g/n. For best results, recommended to use

with a 802.11 b/g/n router.

Adding Additional Alarms: Simply follow the instructions on your Onelink app to add additional alarms to your account.

Identiﬁcation of Events: If your alarm sounds, it is important to ﬁrst identify the type of alarm.

When the Alarm Sounds

What To Do If The Smoke Alarm Sounds

• If the unit alarms and you are not testing the unit, it is warning you of a potentially dangerous situation that

requires your immediate attention. NEVER ignore any alarm. Ignoring the alarm may result in injury or death.

• If the unit alarms get everyone out of the house immediately.

What To Do In Case of a Fire

• Don’t panic; stay clam. Follow your family escape plan.

• Get out of the house as quickly as possible. Don’t stop to get dressed or collect anything.

• Feel doors with the back of your hand before opening them. If a door is cool, open it slowly. Don’t

open a hot door. Keep doors and windows closed, unless you must escape through them.

• Cover your nose and mouth with a cloth (preferably damp. Take short, shallow breaths.)

• Meet at your planned meeting place outside your home, and do a head count to make sure everybody got

out safely. Call the Fire Department as soon as possible from outside. Give your address, then your name.

• Never go back inside a burning building for any reason.

• Contact your Fire Department for ideas on making your home safer.

11

When the Alarm Sounds (Continued)

What To Do If The CO Alarm Sounds

1. Press the Test/Silence button (On App or on unit).

2. Call your emergency services, ﬁre department or 911.

3. Immediately move to fresh air—outdoors or by an open door or window. Do a head count to check that all persons

are accounted for. Do not re-enter the premises, or move away from the open door or window until the emergency

services responder has arrived, the premises have been aired out, and your CO Alarm remains in its normal condition.

4. After following steps 1-3, if your CO Alarm reactivates within a 24-hour period, repeat steps 1-3 and call a qualiﬁed

appliance technician to investigate for sources of CO from fuel-burning equipment and appliances, and inspect for

proper operation of this equipment. If problems are identiﬁed during this inspection have the equipment serviced

immediately. Note any combustion equipment not inspected by the technician, and consult the manufacturers’

instructions, or contact the manufacturers directly, for more information about CO safety and this equipment. Make

sure that motor vehicles are not, and have not, been operating in an attached garage or adjacent to the residence.

NOTE: A qualiﬁed appliance technician is deﬁned as “a person, ﬁrm, corporation, or company that either in person or through a

representative, is engaged in and responsible for the installation, testing, servicing, or replacement of heating, ventilation, air conditioning

(HVAC) equipment, combustion appliances and equipment, and/or gas ﬁreplaces or other decorative combustion equipment.”

Using the Silence Feature

The Silence Feature

This feature is intended to temporarily silence the horn while you identify and correct the problem. Do not

use the Silence Feature in emergency situations. It will not correct a CO problem or extinguish a ﬁre. The

Silence Feature can temporarily quiet an unwanted alarm for several minutes. You can silence this Smoke/

CO Alarm by pressing the Test/Silence button on the alarm cover for at least 3-5 seconds or via the

Onelink app. After the Test/Silence button is released, the Red LED stops during the silence mode.

Silence the End of Life Signal

This silence feature can temporarily quiet the End of Life warning “chirp” for up to 2 days. You can silence the End of

Life warning “chirp” by pressing the Test/Silence button or via the Onelink app. The horn will chirp, acknowledging

that the End of Life silence feature has been activated. After approximately 2 days, the End of Life “chirp” will resume.

!

WARNING: Never deactivate the unit to quiet an unwanted alarm.

Deactivating the alarm disables the unit and removes your protection.

!

WARNING: Actuation of this device indicates the presence of carbon monoxide (CO) which can KILL YOU.

If alarm signal sounds (description of alarm signal, eg four beeps): (1) immediately move to fresh air outdoors or by

an open window. check that all persons are accounted for. Do not reenter the premise or move away from the open

door/window until the emergency service responders have arrived, the premises have been aired out, and your alarm

remains in its normal condition; (2) call you emergency local service (telephone number) (ﬁre department or 911)

(ii) If “service” signal sounds (description of the trouble signal eg. one beep)

12

Using the Silence Feature (Continued)

When the Smoke Alarm is Silenced When the CO Alarm is Silenced

The Smoke Alarm will remain silent for up to

15 minutes, then return to normal operation.

The CO Alarm will remain silent for up to 4 minutes.

If the smoke has not cleared or continues to

increase, the device will go back into alarm.

After 4 minutes, if CO levels remain potentially

dangerous, the horn will start sounding again.

Weekly Testing

You can test this Smoke/CO Alarm by pressing and holding the Test/Silence button on the Alarm cover until

Alarm Voice says “Testing” (typically 3-5 seconds).

During testing, you will see and hear the following sequence:

• The Alarm Voice will say “Testing Alarms... The Alarm will sound and for your protection is very

loud.

This may take a few seconds

”. The LED chases Blue. The Alarm Voice will say “Testing

Smoke”. The Horn will sound 3 beeps. The LED chases and ﬂashes Red. The Alarm Voice will say

“Testing Carbon Monoxide”. The Horn will sound 4 beeps. The LED chases and ﬂashes Red.

• Next, the Alarm Voice will say “Testing Carbon Monoxide.” The Horn will sound 4 beeps, twice. The LED

chases and ﬂashes Red. The Alarm Voice will say Evacuate, Evacuate, there’s Carbon Monoxide in the

[Location. Example: “Kitchen”].” The LED ﬂashes green. The Alarm Voice will say “Highest carbon monoxide

level was 0 PPM.” The LED chases Blue. The Alarm Voice will then say “The testing is almost complete.”

After a pause, the Alarm Voice will say “The test is done, and you are protected.” The LED ﬂashes green.

If the unit does not alarm, make sure it has been activated correctly, and test again.

If the unit still does not alarm, replace it immediately.

!

WARNING: NEVER use an open ﬂame of any kind to test this unit. You might

accidentally damage or set ﬁre to the unit or to your home. NEVER use vehicle

exhaust! Exhaust may cause permanent damage and voids your warranty.

!

WARNING: DO NOT stand close to the Alarm when the horn is sounding. Exposure at close

range may be harmful to your hearing. When testing, step away when horn starts sounding.

!

CAUTION: It is important to test this unit every week to make sure it is working properly.

Using the test button is the recommended way to test this Smoke/CO Alarm.

!

WARNING: Test device operation after vehicle has been in storage, before each trip,

and at least once per week during use.

13

Regular Maintenance

This unit has been designed to be as maintenance-free as possible, but there are a few simple things you

must do to keep it working properly:

• Test it at least once a week.

• Clean the Smoke/CO Alarm at least once a month; gently vacuum the outside of the Smoke/CO

Alarm using your household vacuum’s soft brush attachment. A can of clean compressed air (sold at

computer or oce supply stores) may also be used. Follow manufacturer instructions for use. Test

the Smoke/CO Alarm. Never use water, cleaners or solvents since they may damage the unit.

• If the Smoke/CO Alarm becomes contaminated by excessive dirt, dust and/or grime, and

cannot be cleaned to avoid unwanted alarms, replace the unit immediately.

• Relocate the unit if it sounds frequent unwanted alarms. See “Where This Alarm Should Not Be Installed” for details.

• When the battery becomes weak, the Smoke/CO alarm will “chirp” approximately once a minute (the low

battery warning). This low battery warning should last for up to 7 days, but you should replace the battery

immediately to continue your protection.

!

IMPORTANT: Actual battery service life depends on the Smoke/CO Alarm and the environment

in which it is installed. Regardless of the manufacturer’s suggested battery life, you MUST

replace the battery immediately once the unit starts “chirping” (the “low battery warning”).

Replacement Batteries

Your Smoke/CO alarm requires a 3 cell lithium metal battery. You can purchase your replacement batteries

at www.ﬁrstalertstore.com.

• WARNING: Always use the exact batteries speciﬁed by this User’s manual. DO NOT use

rechargeable batteries. Install batteries correctly with regard to polarity ( + and -).

• Please dispose of or recycle used batteries properly, following any local regulations. Consult your

local waste management authority or recycling organization to ﬁnd an electronics recycling facility

in your area. DO NOT DISPOSE OF BATTERIES IN FIRE. BATTERIES MAY EXPLODE OR LEAK.

• Keep battery out of reach of children. In the event a battery is swallowed, immediately contact your poison

control center, your physician, or the

National Battery Ingestion hotline at 202-

625-3333 as serious injury may occur.

To Replace Batteries

It is recommended that you remove the Smoke/CO Alarm

from the mounting bracket before replacing the batteries.

Step 1 Slide open the battery compartment.

Step 2 Pull out the battery, squeeze release lever

on connector and pull to release battery.

1

Release

Lever

2

14

Regular Maintenance (Continued)

To Replace Batteries (Continued)

Step 3 Connect new battery to connector ensuring that

release lever engages and insert battery into the

battery compartment.

Step 4 Close the battery compartment, and re-mount the

Alarm if you removed it from the mounting bracket.

Then test the unit by pressing the Test button

If the alarm does not test, check the battery to ensure it is properly connected and the alarm is properlymounted in the bracket.

Alarm End of Life

Permanently Deactivating the Alarm

After 10 years of operation, deactivate the Alarm by following the diagram below: Score

label on dotted line and move switch all the way to the right to DEACTIVATE mode.

NOTE: At end of life indication (chirp): unit must be put into deactivation mode to deactivate

remaining stored energy in battery. Unit will no longer function once put into this mode.

Unit will resist re-mounting. Once deactivated, replace Alarm immediately.

1.

Score label on dotted line

2.

Slide switch to the right

SINGLE AND/OR MULTIPLE STATION SMOKE & CO ALARM

MODEL NO. 1042136

SMOKE SENSITIVITY: 0.96 – 2.45 %/ft OBSC.

PHOTOELECTRIC

Replace Alarm 10 Yrs. After Installation

Installed On

Replace By

DEACTIVATE

Follow and Retain User’s

Manual: BRK Brands, Inc.

1301 Joe Battle,

El Paso, TX 79936.

Consumer Affairs:

1-833-ONELINK

(1-833-663-5465)

www.onelink.rstalert.com

www.brkelectronics.com

CONFORMS TO

UL STD 217

& UL STD 2034

3055574

W

WARNING!

Carbon monoxide cannot be seen or smelled but can kill you.

If alarm signal sounds: 1. Operate Test/Silence button.

2. Call your emergency services. (Fire Dept. or 911)

3. Immediately move to fresh air - outdoors or by an open door/window.

Alarm will not operate if batteries are dead, disconnected or

improperly installed. Refer to user's manual for complete battery

replacement list, installation, operating and safety information /

instructions. Use only batteries specied. Use of other batteries may

have a detrimental effect on product operations.

MAINTENANCE AND TESTING:

Constant use at high or low temperatures or high humidity may reduce

battery life. Test after installation, weekly, and after cleaning. Gently

vacuum monthly. Never use water, cleaners or solvents.

HOW TO ACTIVATE ALARM:

Align alarm with mounting bracket and turn clockwise. Chasing Blue

LED's and Welcome Message indicate alarm is activated.

HOW TO DEACTIVATE ALARM:

To deactivate battery, score label on dotted line and move switch all

the way to the right. Once deactivated, the alarm cannot be

reactivated and must be replaced.

ALARM GUIDE:

SMOKE ALARM: Three beeps.

CO ALARM: Four beeps.

REPLACE BATTERY: One "chirp" per minute.

MALFUNCTION: Three “chirps” per minute. Replace alarm.

END OF LIFE: Five “chirps” per minute. Replace alarm.

W

IMPORTANT!

CARBON MONOXIDE SENSITIVITY: If CO levels reach

70ppm, it must activate within 60-240 minutes. At

150ppm within 10-50 minutes. At 400ppm within 4-15

minutes. Refer to user’s manual for more information.

Contains Transmitter Modules FCC ID:

M7U-BT1IOT and FCC ID: TLZ-CU300

Contains Transmitter Modules IC:

10190A-BT1IOT and IC: 6100A-CU300

XXX-XX-XXX

M

A

D

E

I

N

M

E

X

I

C

O

N

0

4

-

3

1

2

5

-

1

6

4

6

7

2

1

SINGLE AND/OR MULTIPLE STATION SMOKE & CO ALARM

MODEL NO. 1042136

SMOKE SENSITIVITY: 0.96 – 2.45 %/ft OBSC.

PHOTOELECTRIC

Replace Alarm 10 Yrs. After Installation

Installed On

Replace By

DEACTIVATE

Follow and Retain User’s

Manual: BRK Brands, Inc.

1301 Joe Battle,

El Paso, TX 79936.

Consumer Affairs:

1-833-ONELINK

(1-833-663-5465)

www.onelink.rstalert.com

www.brkelectronics.com

CONFORMS TO

UL STD 217

& UL STD 2034

3055574

W

WARNING!

Carbon monoxide cannot be seen or smelled but can kill you.

If alarm signal sounds: 1. Operate Test/Silence button.

2. Call your emergency services. (Fire Dept. or 911)

3. Immediately move to fresh air - outdoors or by an open door/window.

Alarm will not operate if batteries are dead, disconnected or

improperly installed. Refer to user's manual for complete battery

replacement list, installation, operating and safety information /

instructions. Use only batteries specied. Use of other batteries may

have a detrimental effect on product operations.

MAINTENANCE AND TESTING:

Constant use at high or low temperatures or high humidity may reduce

battery life. Test after installation, weekly, and after cleaning. Gently

vacuum monthly. Never use water, cleaners or solvents.

HOW TO ACTIVATE ALARM:

Align alarm with mounting bracket and turn clockwise. Chasing Blue

LED's and Welcome Message indicate alarm is activated.

HOW TO DEACTIVATE ALARM:

To deactivate battery, score label on dotted line and move switch all

the way to the right. Once deactivated, the alarm cannot be

reactivated and must be replaced.

ALARM GUIDE:

SMOKE ALARM: Three beeps.

CO ALARM: Four beeps.

REPLACE BATTERY: One "chirp" per minute.

MALFUNCTION: Three “chirps” per minute. Replace alarm.

END OF LIFE: Five “chirps” per minute. Replace alarm.

W

IMPORTANT!

CARBON MONOXIDE SENSITIVITY: If CO levels reach

70ppm, it must activate within 60-240 minutes. At

150ppm within 10-50 minutes. At 400ppm within 4-15

minutes. Refer to user’s manual for more information.

Contains Transmitter Modules FCC ID:

M7U-BT1IOT and FCC ID: TLZ-CU300

Contains Transmitter Modules IC:

10190A-BT1IOT and IC: 6100A-CU300

XXX-XX-XXX

M

A

D

E

I

N

M

E

X

I

C

O

N

0

4

-

3

1

2

5

-

1

6

4

6

7

2

Ionization & Photoelectric Technology

This alarm uses Photoelectric technology.

All First Alert

®

Onelink

®

Smoke Alarms conform to regulatory requirements, including UL217 and are designed

to detect particles of combustion. Smoke particles of varying number and size are produced in all ﬁres.

Ionization Technology

Ionization technology is generally more sensitive than Photoelectric technology at detecting small particles,

which tend to be produced in greater amounts by ﬂaming ﬁres, which consume combustible materials rapidly and

spread quickly. Sources of these ﬁres may include paper burning in a wastebasket or a grease ﬁre in the kitchen.

3

4

15

Ionization & Photoelectric Technology (Continued)

Photoelectric Technology

Photoelectric technology is generally more sensitive than ionization technology at detecting large

particles, which tend to be produced in greater amounts by smoldering ﬁres, which may smolder for hours

before bursting into ﬂame. Sources of these ﬁres may include cigarettes burning in couches or bedding.

NOTE: For maximum protection, use both types of Smoke Alarms on each level and in every bedroom of your home.

Fire Safety Tips

Follow safety rules and prevent hazardous situations:

1. Use smoking materials properly. Never smoke in bed.

2. Keep matches or lighters away from children.

3. Store ﬂammable materials in proper containers.

4. Keep electrical appliances in good condition and don’t overload electrical circuits.

5. Keep stoves, barbecue grills, ﬁreplaces and chimneys grease-free and debris-free.

6. Never leave anything cooking on the stove unattended.

7. Keep portable heaters and open ﬂames, like candles, away from ﬂammable materials.

8. Don’t let rubbish accumulate.

Basic Safety Information

Keep alarms clean and test them weekly. Replace alarms immediately if they are not working

properly. Smoke alarms that do not work cannot alert you to a ﬁre. Keep at least one working

ﬁre extinguisher on every ﬂoor and an additional one in the kitchen. Have ﬁre escape ladders

or other reliable means of escape from an upper ﬂoor in case stairs are blocked.

!

IMPORTANT: Dangers, Warnings and Cautions alert you to important operating instructions

or to potentially hazardous situations. Pay special attention to these items. This Smoke/CO

Alarm is approved for use in single-family residences. It is NOT designed for marine or RV use.

!

CAUTION: This combination Smoke/Carbon Monoxide Alarm has two separate alarms.

The CO Alarm is not designed to detect ﬁre or any other gas. It will only indicate

the presence of carbon monoxide gas at the sensor. Carbon monoxide gas may be

present in other areas. The Smoke Alarm will only indicate the presence of smoke that

reaches the sensor. The Smoke Alarm is not designed to sense gas, heat or ﬂames.

16

Fire Safety Tips (Continued)

What You Need to Know About CO

What is CO?

CO is an invisible, odorless, tasteless gas produced when fossil fuels do not burn completely, or

are exposed to heat (usually ﬁre). Electrical appliances typically do not produce CO.

These fuels include: Wood, coal, charcoal, oil, natural gas, gasoline, kerosene, and propane.

Common appliances are often sources of CO. If they are not properly maintained, are improperly ventilated,

or malfunction, CO levels can rise quickly. CO is a real danger now that homes are more energy ecient. “Air-

tight” homes with added insulation, sealed windows, and other weatherprooﬁng can “trap” CO inside.

Symptoms of CO Poisoning

The following symptoms may be related to CARBON MONOXIDE POISONING and should be discussed with ALL

members of the household:

Mild exposure: Headaches, running nose, sore eyes, often described as “ﬂu”-like symptoms;

Medium Exposure: Dizziness, drowsiness, vomiting;

Extreme Exposure: Unconsciousness, brain damage, death.

Many cases of reported CARBON MONOXIDE POISONING indicate that while victims are aware they are not well, they

become so disoriented they are unable to save themselves by either exiting the building or calling for assistance.

!

IMPORTANT: This CO Alarm measures exposure to CO over time. It alarms if CO levels are extremely high in a short period of time, or if CO

levels reach a certain minimum over a long period of time. The CO Alarm generally sounds an alarm before the onset of symptoms in average,

healthy adults. Why is this important? Because you need to be warned of a potential CO problem while you can still react in time. In many

reported cases of CO exposure, victims may be aware that they are not feeling well, but become disoriented and can no longer react well enough

to exit the building or get help. Also, young children and pets may be the ﬁrst aected. The average healthy adult might not feel any symptoms

when the CO Alarm sounds. However, people with cardiac or respiratory problems, infants, unborn babies, pregnant mothers, or elderly people

can be more quickly and severely aected by CO. If you experience even mild symptoms of CO poisoning, consult your doctor immediately!

!

WARNING: This unit will not operate without battery power. The Smoke/CO Alarm cannot work until you activate the battery

power pack. NEVER ignore any alarm. See “What To Do If Your Smoke/Co Alarm Sounds” on page 11 for more information on how

to respond to an alarm. Failure to respond can result in injury or death. The Silence Features are for your convenience only and will

not correct a problem. See “Using the Silence Feature” on page 12 for details. Always check your home for a potential problem after

any alarm. Failure to do so can result in injury or death. Test this Smoke/CO Alarm once a week. If the alarm ever fails to test correctly,

have it replaced immediately! If the alarm is not working properly, it cannot alert you to a problem. This product is intended for use in

ordinary indoor locations of family living units. It is not designed to measure CO levels in compliance with Occupational Safety and

Health Administration (OSHA) commercial or industrial standards. Individuals with medical conditions that may make them more

sensitive to carbon monoxide may consider using warning devices which provide audible and visual signals for carbon monoxide

concentrations under 30ppm. For additional information on carbon monoxide and your medical condition, contact your physician.

!

WARNING: This product is intended for use in ordinary indoor residential areas. It is not designed to measure

compliance with commercial and industrial standards.

!

CAUTION: This device is designed to protect individuals from the acute eects of carbon monoxide exposure. it will not fully

safeguard individuals with speciﬁc medical conditions. If in doubt, consult a medical practitioner.

17

What You Need to Know About CO (Continued)

Finding the Source of CO After an Alarm

Carbon monoxide is an odorless, invisible gas, which often makes it dicult to locate the source of

CO after an alarm. These are a few of the factors that can make it dicult to locate sources of CO:

• House well ventilated before the investigator arrives.

• Problem caused by “backdrafting.”

• Transient CO problem caused by special circumstances.

Because CO may dissipate by the time an investigator arrives, it may be dicult to locate the source of CO.

BRK Brands, Inc. shall not be obligated to pay for any carbon monoxide investigation or service call.

Potential Sources of CO in the Home

Fuel-Burning Appliances: Like portable heater, gas or wood burning ﬁreplace, gas kitchen range or cooktop,

gas clothes dryer.

Damaged or Insufﬁcient Venting: Corroded or disconnected water heater vent pipe, leaking chimney pipe

or ﬂue, or cracked heat exchanger, blocked or clogged chimney opening.

Improper Use of Appliance/Device: Operating a barbecue grill or vehicle in an enclosed area (like a garage or

screened porch).

Transient CO Problems: “Transient” or on-again-o-again CO problems can be caused by outdoor

conditions and other special circumstances. The following conditions can result in transient CO situations:

1. Excessive spillage or reverse venting of fuel appliances caused by outdoor conditions such as:

• Wind direction and/or velocity, including high, gusty winds. Heavy air in the vent pipes

(cold/humid air with extended periods between cycles).

• Negative pressure dierential resulting from the use of exhaust fans.

• Several appliances running at the same time competing for limited fresh air.

• Vent pipe connections vibrating loose from clothes dryers, furnaces, or water heaters.

• Obstructions in or unconventional vent pipe designs which can amplify the above situations.

2. Extended operation of unvented fuel burning devices (range, oven, ﬁreplace).

3. Temperature inversions, which can trap exhaust close to the ground.

4. Car idling in an open or closed attached garage, or near a home.

These conditions are dangerous because they can trap exhaust in your home. Since these conditions can

come and go, they are also hard to recreate during a CO investigation.

18

Potential Sources of CO in the Home (Continued)

How Can I Protect My Family From CO Poisoning?

A CO Alarm is an excellent means of protection. It monitors the air and sounds a loud alarm

before Carbon Monoxide levels become threatening for average, healthy adults.

A CO Alarm is not a substitute for proper maintenance of home appliances.

To help prevent CO problems and reduce the risk of CO poisoning:

• Clean chimneys and ﬂues yearly. Keep them free of debris, leaves, and nests for proper air ﬂow.

Also, have a professional check for rust and corrosion, cracks, or separations. These conditions can

prevent proper air movement and cause back-drafting. Never “cap” or cover a chimney in any way

that would block air ﬂow.

• Test and maintain all fuel-burning equipment annually. Many local gas or oil companies and HVAC

companies oer appliance inspections for a nominal fee.

• Make regular visual inspections of all fuel-burning appliances. Check appliances for excessive rust and

scaling. Also check the ﬂame on the burner and pilot lights. The ﬂame should be blue. A yellow ﬂame

means fuel is not being burned completely and CO may be present. Keep the blower door on the furnace

closed. Use vents or fans when they are available on all fuel-burning appliances. Make sure appliances

are vented to the outside. Do not grill or barbecue indoors, or in garages or on screen porches.

• Check for exhaust back-ﬂow from CO sources. Check the draft hood on an operating furnace for a

back-draft. Look for cracks on furnace heat exchangers.

• Check the house or garage on the other side of shared wall.

• Keep windows and doors open slightly. If you suspect that CO is escaping into your home, open

a window or a door. Opening windows and doors can signiﬁcantly decrease CO levels.

Regulatory Information for CO Alarms

What Levels of CO Cause an Alarm?

Underwriters Laboratories Inc. Standard UL2034 requires residential CO Alarms to sound when exposed

to levels of CO and exposure times as described below. They are measured in parts per million (ppm) of

CO over time (in minutes).

UL2034 Required Alarm Points*:

• If the alarm is exposed to 400 ppm of CO, IT MUST ALARM BETWEEN 4 & 15 MINUTES.

• If the alarm is exposed to 150 ppm of CO, IT MUST ALARM BETWEEN 10 & 50 MINUTES.

• If the alarm is exposed to 70 ppm of CO, IT MUST ALARM BETWEEN 60 & 240 MINUTES.

*Approximately 10% of COHb exposure at levels of 10% to 95% Relative Humidity (RH).

This unit is designed not to alarm when exposed to a constant level of 30 ppm for 30 days.

19

Regulatory Information for CO Alarms (Continued)

!

IMPORTANT: CO alarms are designed to alarm before there is an immediate life threat.

Since you cannot see or smell CO, never assume it’s not present. An exposure to 100

ppm of CO for 20 minutes may not aect average, healthy adults but after 4 hours the

same level may cause headaches. An exposure to 400 ppm of CO may cause headaches

in average, healthy adults after 35 minutes, but can cause death after 2 hours.

Standards

Underwriters Laboratories Inc. Single and Multiple Station carbon monoxide alarms UL2034. According to Underwriters

Laboratories Inc. UL2034, Section 1-1.2: “Carbon monoxide alarms covered by these requirements are intended to respond to

the presence of carbon monoxide from sources such as, but not limited to, exhaust from internal-combustion engines, abnormal

operation of fuel-ﬁred appliances, and ﬁreplaces. CO Alarms are intended to alarm at carbon monoxide levels below those

that could cause a loss of ability to react to the dangers of Carbon Monoxide exposure.” This CO Alarm monitors the air at the

Alarm, and is designed to alarm before CO levels become life threatening. This allows you precious time to leave the house

and correct the problem. This is only possible if Alarms are located, installed, and maintained as described in this manual.

Gas Detection at Typical Temperature and Humidity Ranges

The CO Alarm is not formulated to detect CO levels below 30 ppm typically. Tested for false alarm resistance to

Methane (500 ppm), Butane (300 ppm), Heptane (500 ppm), Ethyl Acetate (200 ppm), Isopropyl Alcohol (200

ppm) and Carbon Dioxide (5000 ppm). Values measure gas and vapor concentrations in parts per million.

Audible Alarm

85 dB minimum at 10 feet (3 meters).

This carbon monoxide alarming device is designed to detect carbon monoxide gas from ANY source of combustion,

It is NOT designed to detect smoke, ﬁre, or any other gases.

Regulatory Information for Smoke Alarms

Installing Smoke Alarms in Single-Family Residences

The National Fire Protection Association (NFPA), recommends one Smoke Alarm on every ﬂoor, in every

sleeping area, and in every bedroom. In new construction, the Smoke Alarms must be AC powered

and interconnected. See “Agency Placement Recommendations” for details. For additional coverage,

it is recommended that you install a Smoke Alarm in all rooms, halls, storage areas, ﬁnished attics,

and basements, where temperatures normally remain between 40˚ F (4.4˚ C) and 100˚ F (37.8˚ C).

Make sure no door or other obstruction could keep smoke from reaching the Smoke Alarms.

For your information, the National Fire Alarm and Signaling Code, NFPA 72, reads as follows:

Required Detection. Where required by applicable laws, codes, or standards for a speciﬁc type of

occupancy, approved single- and multiple-station smoke alarms shall be installed as follows:

• In all sleeping rooms and guest rooms

• Outside of each separate dwelling unit sleeping area, within 21 ft (6.4 m) of any door to a sleeping room,

the distance measured along a path of travel

20

Regulatory Information for Smoke Alarms (Continued)

• On every level of a dwelling unit, including basements

• On every level of a residential board and care occupancy (small facility), including basements and

excluding crawl spaces and unﬁnished attics

• In the living area(s) of a guest suite In the living area(s) of a residential board and care occupancy

!

IMPORTANT: Speciﬁc requirements for Smoke Alarm installation vary from state to state

and from region to region. Check with your local Fire Department for current requirements in

your area. It is recommended AC or AC/DC units be interconnected for added protection.

BASEMENT

BEDROOM

GARAGE

KITCHEN

HALLWAY BEDROOM

LIVING ROOM

Smoke Alarm

One on every level and

in every bedroom

Carbon Monoxide

One on every level and

in every bedroom

Fire Extinguisher

One on every level, plus

kitchen and garage

Recommended Placement

Regulatory Information

Federal Communications Commission (FCC) Compliance Statement

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning the equipment

o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

La page est en cours de chargement...

Onelink 1042136 Manuel utilisateur

Onelink 1042136 Manuel utilisateur

dans d''autres langues

Autres documents