Campbell Hausfeld TL0502 Manuel utilisateur

Marque: Campbell Hausfeld

Modèle: TL0502

Catégorie: Clés à chocs électriques

Taper: Manuel utilisateur

Ce manuel convient également à

Impact Driver TL0502

1/2 inch Impact

Wrench

Table of Contents

Description . . . . . . . . . . . . . . . . . . . . . 1

Unpacking . . . . . . . . . . . . . . . . . . . . . . 1

Safety Guidelines . . . . . . . . . . . . . . . . 1

Important Safety Information . . . . . . 1

Tool Components and

Specifications. . . . . . . . . . . . . . . . . . . . 2

Operating Instructions . . . . . . . . . . . . 4

Lubrication . . . . . . . . . . . . . . . . . . . . 4

Recommended Hookup. . . . . . . . . . 4

Operational Mode . . . . . . . . . . . . . . 4

User-Maintenance Instructions . . . . . 5

Troubleshooting Charts . . . . . . 6 and 7

Warranty . . . . . . . . . . . . . . . . . . . . . . . 8

Description

This is a rocking dog type impact

wrench designed for DIY projects and

general purpose applications such as

maintenance, car repair, and lawn and

garden equipment. Not intended for

assembly line

applications or heavy duty

usage.

Unpacking

After unpacking the unit, inspect

carefully for any damage that may

have occurred during transit. Make sure

to tighten fittings, bolts, etc., before

putting unit into service.

CALIFORNIA PROPOSITION 65

This product or

its power cord may

contain chemicals known to the State

of California to cause cancer and birth

defects or other reproductive harm.

Wash hands after handling.

You can create dust when

you cut, sand, drill or grind

materials such as wood,

paint, metal, concrete, cement, or other

masonry. This dust often contains

chemicals known to cause cancer, birth

defects, or other reproductive harm.

Wear protective gear.

Safety Guidelines

This manual contains information

that is very important to know and

understand. This information is

provided for SAFETY and to PREVENT

EQUIPMENT PROBLEMS. To help

recognize this information, observe the

following symbols.

Danger indicates an

imminently

hazardous situation which, if not

avoided, WILL result in death or serious

injury.

Warning indicates a

potentially

hazardous situation which, if not

avoided, COULD result in death or

serious injury.

Caution indicates a

potentially

hazardous situation which, if not

avoided, MAY result in minor or

moderate injury.

Notice indicates

important

information, that if not followed, may

cause damage to equipment.

NOTE: Information that requires special

attention.

Important Safety Instructions

INSTRUCTIONS PERTAINING TO A

RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS

This manual contains safety, operational

and maintenance information. Contact

your Campbell Hausfeld representative

if you have any questions.

When using tools,

basic precautions

should always be followed, including

the following:

Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described.

Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or

property damage! Retain instructions for future reference.

REMINDER: Keep your dated proof of purchase for warranty purposes!

Attach it to this manual or file it for safekeeping.

IN732800AV 1/10

See Warranty on page 8 for important information about commercial use of this product.

Operating Instructions TL0502

Locate model and date code on

tool and record below:

Model No.: _____________________

Date Code: _____________________

Retain these numbers for

future reference.

visit www.chpower.com

Model TL0502

GENERAL

a. To reduce the risks of

electric shock, fire, and

injury to persons, read all

the instructions before

using the tool.

b. Be thoroughly familiar with the

controls and the proper use of the

equipment. Follow all instructions.

Contact your Campbell Hausfeld

representative if you have any

questions.

c. Only persons well acquainted with

these rules of safe operation should

be allowed to use the unit.

Read and

understand tool

labels and manual. Failure to follow

warnings, dangers, and cautions could

result in DEATH or SERIOUS INJURY.

WORK AREA

a. Keep the work area clean and well

lighted. Cluttered benches and dark

areas increase the risks of electric

shock, fire, and injury to persons.

b. Do not operate the tool

in explosive atmospheres,

such as in the presence

of flammable liquids,

gases, or dust. The tool is

able to create sparks resulting in the

ignition of the dust or fumes.

c. Keep bystanders, children, and

visitors away while operating the

tool. Distractions are able to result in

the loss of control of the tool.

PERSONAL SAFETY

a. Stay alert. Watch what you are

doing and use common sense

when operating the tool. Do not

use the tool while tired or under

the influence of drugs, alcohol,

or medication. A moment of

inattention while operating the

tool increases the risk of injury to

persons.

b. Dress properly. Do not wear loose

clothing or jewelry. Contain long

hair. Keep hair, clothing, and

gloves away from moving parts.

Loose clothes, jewelry, or long

hair increases the risk of injury to

persons as a result of being caught

in moving parts.

c. Avoid unintentional starting.

Be sure the switch is off before

connecting to the air supply. Do not

carry the tool with your finger on

the switch or connect the tool to the

air supply with the switch on.

d. Do not overreach. Keep proper

footing and balance at all times.

Proper footing and balance enables

Operating Instructions

Important Safety Instructions

(Continued)

better control of the tool in

unexpected situations.

e. Use safety equipment. A dust mask,

non-skid safety shoes and a hard

hat must be used for the applicable

conditions.

f. Always wear eye

protection.

g. Always wear hearing

protection when using

the tool. Prolonged

exposure to high intensity

noise is able to cause

hearing loss.

h. Do not attach the hose or tool to

your body. Attach the hose to the

structure to reduce the risk of loss of

balance if the hose shifts.

Always remain in a

ﬁrmly balanced

position when using or handling the

tool.

Avoid long extended

periods of work

with the tool. Stop using the tool if you

feel pain in hands or arms.

i. Never point an air tool at oneself

or any other person. Serious injury

could occur.

j. Do not put hands near or under

moving parts.

Tool Components and Specifications

www.chpower.com

Avg SCFM & psi . . . . . . . . . .5.1 @ 90 psig

(20% usage)

Continuous SCFM . .. . . . . .25.4 @ 90 psig

(100% usage)

Max. Operating

Pressure . . . . . . . . . . . . . . . . . . . . .90 psig

Rated RPM . . . . . . . . . . . . . . . . . . . . .7000

Max Torque . . . . . . . . . . . . . . . . .250 ft.lb

Working Torque . . .. . . . . . . . 60-200 ft.lb

Impact Mechanism

Type . . . . . . . . . . . . . . . . . . . Rocking Dog

Bolt Capacity . . . . . . . . . . . . . . . . 1/2 inch

Air Inlet. . . . . . . . . .1/4 inch NPT (Female)

Min Hose Size . . . . .. . . . . . . . . . . 3/8 inch

Drive . . . . . . . . . . . . . . . . . . . .1/2 inch sq.

Weight . . . . . . . . . . . . . . . . . . . . . . . 5 lbs.

Anvil

Forward/Reverse

Button

Trigger

Regulator

Air Inlet

Do not drop or

throw the tool.

Dropping or throwing the tool can

result in damage that will make the tool

unusable or unsafe. If the tool has been

dropped or thrown, examine the tool

closely for bent, cracked or broken parts

and air leaks. STOP and repair before

using or serious injury could occur.

Clean and check all

air supply hoses

and ﬁttings before connecting the

tool to an air supply. Replace any

damaged or worn hoses or ﬁttings.

Tool performance or durability may be

reduced.

SERVICE

a. Tool service must be performed only

by qualified repair personnel.

b. When servicing a tool, use only

identical replacement parts. Use

only authorized parts.

c. Use only the lubricants supplied

with the tool or specified by the

manufacturer.

Do not make any

modiﬁcations to

the tool without ﬁrst obtaining written

approval from Campbell Hausfeld. Do

not use the tool if any shields or guards

are removed or altered. Do not use the

tool as a hammer. Personal injury or

tool damage may occur.

AIR SOURCE

a. Never connect to an air source that

is capable of exceeding 200 psi.

Over pressurizing the tool is able

to result in bursting, abnormal

operation, breakage of the tool or

serious injury to persons. Use only

clean, dry, regulated compressed air

at the rated pressure or within the

rated pressure range as marked on

the tool. Always verify prior to using

the tool that the air source has been

adjusted to the rated air pressure or

within the rated air-pressure range.

b. Never use oxygen, carbon dioxide,

combustible gases or any bottled

gas as an air source for the tool.

Such gases are capable of explosion

and serious injury to persons.

TOOL USE AND CARE

a. Use clamps or another practical way

to secure and support the workpiece

to a stable platform. Holding the

work by hand or against the body is

unstable and is able to lead to loss

of control.

b. Do not force the tool. Use the

correct tool for the application. The

correct tool will do the job better

and safer at the rate for which the

tool is designed.

c. Do not use the tool if the switch

does not turn the tool on or off. Any

tool that cannot be controlled with

the switch is dangerous and must be

repaired.

Disconnect the

tool from the air

source before making adjustments,

doing tool maintenance, clearing

jams, leaving work area,loading,

or unloading the tool. Such

precautionary measures reduce the

risk of injury to persons.

e. Store the tool when it is idle out

of reach of children and other

untrained persons. A tool is

dangerous in the hands of untrained

users.

f. Maintain the tool with care. Keep

a cutting tool sharp and clean. A

properly maintained tool, with sharp

cutting edges reduces the risk of

binding and is easier to control.

g. Check for misalignment or binding

of moving parts, breakage of parts,

and any other condition that affects

the tool’s operation. If damaged,

have the tool serviced before using.

Many accidents are caused by poorly

maintained tools. There is a risk of

bursting if the tool is damaged.

h. Use only accessories that are

identified by the manufacturer for

the specific tool model. Use of an

accessory not intended for use with

the specific tool model increases the

risk of injury to persons.

i. Selecting an appropriate tool

actuation system, taking into

consideration the work application

for which the tool is used.

Never use

gasoline

or other ﬂammable liquids

to clean the tool. Never use

the tool in the presence of

ﬂammable liquids or gases. Vapors

could ignite by a spark and cause an

explosion which will result in death or

serious personal injury.

Do not exceed

maximum operating

pressure of the air tool (90 psi). The air

tool could explode and result in death

or serious personal injury.

Do not use hand

tool sockets. Use

impact quality sockets only. Hand

tool sockets are “glass-hard” and will

shatter and can cause serious personal

injury if used with air tools.

j. Never trigger the tool when

not applied to a work object.

Attachments must be securely

attached. Loose attachments can

cause serious injury.

Release all pressure

from the system

before attempting to install, service,

relocate or perform any maintenance.

k. Keep all nuts, bolts and screws tight

and ensure equipment is in safe

working condition.

Always disconnect

the tool from

the power source when unattended,

performing any maintenance or repair,

clearing a jam, or moving the tool to a

new location.

Always ﬁt tool

with a ﬁtting or

hose coupling on or near the tool in

such a manner that all compressed air

in the tool is discharged at the time the

ﬁtting or hose coupling is disconnected.

Do not use a check valve or any other

ﬁtting which allows air to remain in the

tool. Death or serious personal injury

could occur.

Never carry the tool

by the air hose

or pull the hose to move the tool or

a compressor. Keep hoses away from

heat, oil and sharp edges. Replace any

hose that is damaged, weak or worn.

Personal injury or tool damage could

occur.

Do not operate or allow

anyone else to operate

the tool if any warnings

or warning labels are not legible.

Warnings or warning labels are located

on the tool magazine and body.

TL0502

Important Safety Instructions

(Continued)

WARNING

www.chpower.com

Operating Instructions

Do not use any type of

reactive gases, including, but

not limited to, oxygen and

combustible gases, as a power source.

Use ﬁltered, lubricated, regulated

compressed air only. Use of a reactive

gas instead of compressed air may

cause the tool to explode which will

cause death or serious personal injury.

Use only a pressure-regulated

compressed air source to limit

the air pressure supplied to

the tool. The regulated pressure must

not exceed 90 psi. If the regulator fails,

the pressure delivered to the tool must

not exceed 200 psi. The tool could

explode which will cause death or

serious personal injury.

c. Do not exceed any pressure rating of

any component in the system.

SAVE THESE INSTRUCTIONS

DO NOT DISCARD

OPERATING INSTRUCTIONS

LUBRICATION

Proper lubrication is the owner’s

responsibility. Failure to lubricate the air

tool properly will dramatically shorten

the life of the tool and will void the

warranty.

This impact

wrench requires

lubrication before the initial use and

before and after each additional use.

Impact wrenches require lubrication

throughout the life of the tool and

must be lubricated in two separate

areas: the air motor and the impact

mechanism. Air tool oil is recommended

because this oil cleans, lubricates and

inhibits rust all in one step.

AIR MOTOR LUBRICATION

The motor must be lubricated daily. An

air motor cannot be oiled too often.

Disconnect the

impact wrench from

the air supply before lubricating.

1. Disconnect the impact wrench from

the air supply.

2. Turn the impact wrench upside

down.

3. While pulling the trigger, squeeze

approximately a 1/4 oz. of airtool

oil in the air inlet. Then, push the

forward and reverse button in both

directions.

After an air tool

has been lubricated,

oil will discharge through the exhaust

port during the ﬁrst few seconds of

operation. Thus, THE EXHAUST PORT

MUST BE COVERED WITH A TOWEL

before applying air pressure. FAILURE

TO COVER THE EXHAUST PORT CAN

RESULT IN SERIOUS INJURY.

4. Connect the impact wrench to the

air supply and cover the exhaust port

with a towel. Run the impact wrench

in both the forward and reverse

directions for 20 to 30 seconds. Oil

will discharge from the exhaust port

when air pressure is applied.

IMPACT MECHANISM LUBRICATION

Lubricate the impact mechanism

monthly.

Disconnect the

impact wrench from

the air supply before lubricating.

1. Disconnect the impact wrench from

the air supply.

2. Remove the slotted screw or allen

head screw from the oil port hole.

3. Squeeze approximately 1 oz. of air

tool oil in the oil port hole. Replace

the screw.

4. Reconnect the air supply to the

impact wrench and run for 20 to 30

seconds. Lubricate the entire impact

mechanism by rotating the tool

upside down and sideways while

running the tool.

5. Remove the screw and hold the oil

port hole over a suitable container

to allow excess oil to drain.

Sometimes triggering the tool when

dumping the oils helps to force out

the excess oil.

6. If the oil is dirty, repeat the

procedure above until the oil comes

out clear. Install the screw and

tighten. The residual oil remaining

in the impact mechanism chamber

is all that is needed for proper

lubrication.

RECOMMENDED HOOKUP

The illustration below shows the

recommended hookup for the tool.

1. The air compressor

must be able to

maintain a minimum

of 60 psi when the

tool is being used. An inadequate air

supply can cause a loss of power and

inconsistent driving.

Recommended Hookup

Quick Plug

Quick

Coupler

Air Hose

Quick Plug

(Optional)

Quick

Coupler

(Optional)

Regulator

Lubricator Filter

60 psi

Min.

90 psi

Max.

www.chpower.com

90 psi

Important Safety Instructions

(Continued)

TL0502

OPERATING INSTRUCTIONS

(Continued)

2. An oiler can be

used to provide oil

circulation through

the tool. A filter can

be used to remove

liquid and solid impurities which can

rust or “gum up” internal parts of

the tool.

3. Always use air supply hoses with

a minimum working pressure

rating equal to or greater than the

pressure from the power source if a

regulator fails, or 200 psi, whichever

is greater. Use 1/4 inch air hose for

runs up to 50 feet. Use 3/8 inch air

hoses for 50 foot run or longer.

4. Use a pressure regulator on the

compressor, with an operating

pressure of 0 psi - 125 psi. A pressure

regulator is required to control

the operating pressure of the tool

between 60 psi and 90 psi.

REGULATOR OPERATION

This impact wrench is equipped with

several power (speed) settings. Use the

switch on the rear of the tool to select

the proper setting before operating

tool. The tool has 3 forward settings

and 1 reverse setting. Do not change

settings while tool is running.

SPEED ADJUSTMENT

An impact wrench should never be used

to set torque. Use a torque wrench to

set the torque.

To remove lugs or bolts, set the

regulator to the maximum setting.

When installing, always use a torque

wrench to attain the proper torque of

the lugs or bolts.

When reassembling

be careful not to

overtighten. Bolts may fail or cause a

hazardous condition. Be sure to set the

regulator to the minimum setting then

use a torque wrench to set torque.

NOTE: It is not recommended to install

a quick coupler between the tool and

the whip hose.

Using fittings or air hoses which are

too small can create a pressure drop

and reduce the power of the tool. For

3/8, 1/2 and 3/4 inch impact wrenches

use 3/8 inch (I.D.) fittings with 1/4 inch

NPT threads. Most compressors are

shipped with a short, 1/4 inch I.D. hose.

For proper performance and more

convenience, use a 3/8 inch I.D. hose.

Hoses longer than 50 feet should have a

1/2 inch I.D.

Never carry a tool

by the hose or

pull the hose to move the tool or a

compressor. Keep hoses away from

heat, oil and sharp edges. Replace any

hose that is damaged, weak or worn.

USER-MAINTENANCE

INSTRUCTIONS

TECHNICAL SERVICE

Please call our Tool Hotline at 1-800-

543-6400 with any questions regarding

the operation or repair of this tool or

for additional copies of this manual.

REPLACEMENT PARTS INFORMATION

For information regarding where to

order replacement parts, call toll free

1-800-543-8622. Please provide the

following information:

 •Modelnumber

 •Stamped-incode

 •Partnumberanddescription

TOOL REPAIR

Only qualified personnel should repair

the tool and they should use genuine

Campbell Hausfeld replacement parts

and accessories, or parts and accessories

which perform equivalently.

ASSEMBLY PROCEDURE FOR SEALS

When repairing a tool, the internal

parts must be cleaned and lubricated.

Parker O-lube or equivalent must be

used on all o-rings. Each o-ring must be

coated with O-lube before assembling.

A small amount of oil must be used on

all moving surfaces and pivots. After

reassembling, a few drops of 30W

non-detergent oil or equivalent, must

be added through the air line before

testing.

STORAGE

The impact wrench must be lubricated

before storing. Follow the air motor

lubrication instructions with an

exception to step 4. Only run the impact

wrench for 2 to 3 seconds instead of 20

to 30 seconds because more oil needs

to remain in the impact wrench when

storing. The tool should be stored in a

cool dry place.

200 psi or greater

3/8 inch I.D.

www.chpower.com

Symptom Possible Cause(s) Corrective Action

Tool runs slowly or will not

operate

1. Grit or gum in tool 1. Flush the tool with air tool oil, gum solvent,

or an equal mixture of SAE 10 motor oil

and kerosene. If air tool oil is not used,

lubricate the tool after cleaning

2. No oil in tool 2. Lubricate the tool according to the

lubrication instructions in this manual

3. Low air pressure 3. a. Adjust the regulator on the tool to

the maximum setting

b. Adjust the compressor regulator to tool

maximum while the tool is running

free

4. Air hose leaks 4. Tighten and seal hose fittings if leaks are

found

5. Pressure drops 5. a. Be sure the hose is the proper size.

Long hoses or tools using large volumes

of air may require a hose with an I.D.

of 1/2 inch or larger depending on the

total length of the hose

b. Do not use a multiple number of hoses

connected together with quick connect

fittings. This causes additional pressure

drops and reduces the tool power.

Directly connect the hoses together

6. Worn ball bearing in motor 6. Remove and inspect bearing for rust, dirt

and grit or worn race. Replace or clean and

regrease bearing with bearing grease

Moisture blowing out of tool 1. Water in tank 1. Drain tank. (See air compressor manual).

Oil tool and run until no water is evident.

Oil tool again and run 1-2 seconds

2. Water in the air lines/hoses 2. a. Install a water separator/filter.

NOTE: Separators only work properly when

the air passing through the separator is

cool. Locate the separator/filter as far as

possible from the compressor

b. Install an air dryer

c. If the original separator will not

separate all the water from the air,

install a belt air filter

Troubleshooting Chart

Stop using tool immediately if any of the following problems occur. Serious personal injury could occur.

Any repairs or replacements must be done by a Qualiﬁed Service Person or Authorized Service Center.

Operating Instructions

www.chpower.com

TL0502

www.chpower.com

Impact Mechanism Troubleshooting Guide

Symptom Possible Cause(s) Corrective Action

Impacts slowly or will not

impact

1. Lack of lubrication 1. Lubricate the air motor and the impact

mechanism. (See Lubrication section of

this manual)

2. Tool regulator set in wrong position 2. Adjust the regulator on the tool to the

maximum setting

3. In-line regulator or compressor

regulator set too low

3. Adjust regulators in the air system

Impacts rapidly but will not

remove bolts

1. Worn impact mechanism 1. a. Replace worn impact mechanism

components

b. Return impact wrench to Authorized

Service Center for repair

Does not impact 1. Broken impact mechanism 1. a. Replace broken impact mechanism

components

b. Return impact wrench to an Authorized

Service Center for repair

Operating Instructions

www.chpower.com

Limited Warranty

1. DURATION: From the date of purchase by the original purchaser as follows: One (1) Year.

2. WHO GIVES THIS WARRANTY (WARRANTOR): Campbell Hausfeld / Scott Fetzer Company, 100 Production Drive, Harrison,

Ohio, 45030, Telephone: (800) 543-6400

3. WHO RECEIVES THIS WARRANTY (PURCHASER): The original purchaser (other than for purposes of resale) of the Campbell

Hausfeld product.

4. WHAT PRODUCTS ARE COVERED BY THIS WARRANTY: This Campbell Hausfeld air tool.

5. WHAT IS COVERED UNDER THIS WARRANTY: Substantial defects in material and workmanship which occur within the

duration of the warranty period with the exceptions below.

6. WHAT IS NOT COVERED UNDER THIS WARRANTY:

A. Implied warranties, including those of merchantability and FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED FROM

THE DATE OF ORIGINAL PURCHASE AS STATED IN THE DURATION. If this product is used for commercial, industrial

or rental purposes, the warranty will apply for ninety (90) days from the date of purchase. Some States do not allow

limitation on how long an implied warranty lasts, so the above limitations may not apply to you.

B. ANY INCIDENTAL, INDIRECT, OR CONSEQUENTIAL LOSS, DAMAGE, OR EXPENSE THAT MAY RESULT FROM ANY

DEFECT, FAILURE, OR MALFUNCTION OF THE CAMPBELL HAUSFELD PRODUCT. Some States do not allow the exclusion

or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

C. Any failure that results from an accident, purchaser’s abuse, neglect or failure to operate products in accordance with

instructions provided in the owner’s manual(s) supplied with product. Accident, purchaser's abuse, neglect or failure

to operate products in accordance with instructions shall also include the removal or alteration of any safety devices.

If such safety devices are removed or altered, this warranty is void.

D. Normal adjustments which are explained in the owner’s manual(s) provided with the product.

E. Items or service that are normally required to maintain the product, e.g. o-rings, springs, gaskets, packings or seals,

lubricants, motor vanes, impact mechanism, or any other expendable part not specifically listed. These items will only

be covered for ninety (90) days from date of original purchase. Underlined items are warranted for defects in material

and workmanship only.

7. RESPONSIBILITIES OF WARRANTOR UNDER THIS WARRANTY: Repair or replace, at Warrantor’s option, products or

components which are defective, have malfunctioned and/or failed to conform within the duration of the specific warranty

period.

8. RESPONSIBILITIES OF PURCHASER UNDER THIS WARRANTY:

A. Provide dated proof of purchase and maintenance records.

B. Call Campbell Hausfeld (800) 543-6400 to obtain your warranty service options. Freight costs must be borne by the

purchaser.

C. Use reasonable care in the operation and maintenance of the products as described in the owner’s manual(s).

9. WHEN WARRANTOR WILL PERFORM REPAIR OR REPLACEMENT UNDER THIS WARRANTY: Repair or replacement will be

scheduled and serviced according to the normal work flow at the servicing location, and depending on the availability of

replacement parts.

This Limited Warranty applies in the United States, Canada and Mexico only and gives you specific legal rights. You may also

have other rights which vary from state to state or country to country.

Table des matières

Descripion . . . . . . . . . . . . . . . . . . . . 1-Fr

Déballage . . . . . . . . . . . . . . . . . . . . 1-Fr

Directives de sécurité . . . . . . . . . . . 1-Fr

Importantes instructions

de sécurité . . . . . . . . . . . . . . . . . . . . 1-Fr

Pièces détachées et fisch technique

mécanisme de la l'outil. . . . . . . . . . 2-Fr

Mode d’emploi . . . . . . . . . . . . . . . . 4-Fr

Graissage . . . . . . . . . . . . . . . . . . . 4-Fr

Branchement recommandé. . . . . 4-Fr

Mode d’opération . . . . . . . . . . . . 5-Fr

Instructions de maintenance

de l'utilisateur . . . . . . . . . . . . . . . . . 5-Fr

Guide de dépannage . . . . . .6-Fr et 7-Fr

Garantie limitée . . . . . . . . . . . . . . . 8-Fr

Description

C’est une clé à chocs de type marteau

à bascule conçu pour le bricolage et

les applications généraux tels que

l’entretien, la réparation d’automobile,

ainsi que l’équipement de pelouse et

jardin. Ce modèle n’est pas conçu pour

les applications de chaînes d’assemblage

ni pour l’usage à grande puissance.

Déballage

Dès que l’appareil est déballé,

l’inspecter attentivement pour tout

signe de dommages en transit. S’assurer

de resserrer tous les raccords, boulons,

etc. avant de le mettre en service.

PROPOSITION 65 DE CALIFORNIE

Ce produit ou son

cordon peuvent

contenir des produits chimiques qui, de

l’avis de l’État de Californie, causent le

cancer et des anomalies congénitales

ou autres problèmes de reproduction.

Lavez-vous les mains après la

manipulation.

Vous pouvez créer de la

poussière en coupant,

ponçant, perçant ou

meulant les matériaux tels que le

bois, la peinture, le métal, le béton,

le ciment ou autre maçonnerie. Cette

poussière contient souvent des produits

chimiques reconnus pour causer le

cancer, les déformations congénitales

ou autres problèmes de la reproduction.

Porter de l’équipement de protection.

Directives de Sécurité

Ce manuel contient de l’information

très importante qui est fournie pour

la SÉCURITÉ et pour ÉVITER LES

PROBLÈMES D’ÉQUIPEMENT. Rechercher

les symboles suivants pour cette

information.

Danger indique une

situation

hasardeuse imminente qui RÉSULTERA

en perte de vie ou blessures graves.

Avertissement

indique une

situation hasardeuse potentielle

qui PEUT résulter en perte de vie ou

blessures graves.

Attention indique

une situation

hasardeuse potentielle qui PEUT résulter

en blessures.

Avis indique de

l’information

importante pour éviter le dommage de

l’équipement.

REMARQUE : L’information qui exige

une attention spéciale.

Importantes instructions

de sécurité

INSTRUCTIONS PORTANT SUR UN

RISQUE D’INCENDIE, UN CHOC

ÉLECTRIQUE OU DES BLESSURES

AUX PERSONNES

Ce manuel contient des informations

concernant la sécurité, le

fonctionnement et l’entretien.

Contacter votre représentant Campbell

Hausfeld si vous avez des questions.

En utilisant les

outils, il faut suivre

les précautions de base, y compris ce

qui suit :

Veuillez lire et conserver ces instructions. Lire attentivement avant de commencer à assembler, installer, faire fonctionner ou entretenir

l'appareil décrit. Protégez-vous et les autres en observant toutes les informations sur la sécurité. Négliger d'appliquer ces instructions peut

résulter en des blessures corporelles et/ou en des dommages matériels ! Conserver ces instructions pour références ultérieures.

IN732800AV 1/10

Voir la Garantie à la page 16 pour de l’information importante sur l’utilisation commercial de ce produit.

1-Fr

MÉMENTO: Gardez votre preuve datée d'achat à fin de la garantie!

Joignez-la à ce manuel ou classez-la dans un dossier pour plus de sécurité.

Trouver le numéro de modèle et

le code date sur le chargeur de

l’outil et inscrire plus bas :

du Model : __________________

Code de date : __________________

Conserver ces numéros

comme référence.

Clé à Chocs de

12,7 mm (1/2 po)

Instructions d’Utilisation TL0502