Whirlpool AZB 8574 Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi
1
Machine operation
Additional information (including troubleshooting and service) can be found in the individual sections of the
Instructions For Use.
Sort laundry by:
Material thickness: whenever the load is greater than the dryer can handle,
separate laundry according to weight (e.g. dry towels and thin underwear separately).
Type of material: cotton (linen); synthetic textiles (easy care).
Dryness level: cupboard dry, iron dry etc.
Do not tumble dry: woollens, silk, nylon stockings, delicate embroidery, fabrics with
metallic decorations, bulky items such as sleeping bags or pillows.
Check that all fastenings are closed and that pockets are empty. Ensure that there are
no cigarette lighters in the wash. Turn laundry inside out.
Place laundry loosely in the drum to achieve even drying throughout. Then close the
door.
Select the required drying programme by turning the programme selector knob (for
information, refer to programme table).
Select the required option by pressing the corresponding button.
The indicator lamp above the relevant button lights up to confirm your selection.
A fast blinking LED indicates that an invalid selection has been made (incompatible
option). Press the button again to cancel the option.
Start the drying programme by pressing the “Start (Pause)” button.
The relevant indicator lamp lights up.
Changing programme selection: if the selected programme is changed during
drying, the dryer stops. The “Start (Pause)” indicator lamp flashes.
To run the new programme, press the “Start (Pause)” button again.
Interrupting programme: to interrupt a drying cycle, press the “Start (Pause)”
button and open the door. Wait at least 5 minutes, to allow the laundry to cool down,
before unloading the dryer. For your safety, the drying cycle stops automatically if you
open the door. To restart the cycle after opening the door, press the “Start (Pause)”
button again.
Warning: never stop a tumble dryer before the end of the drying cycle, unless all
items are quickly removed and spread out so that the heat is dissipated.
The final part of a drying cycle occurs without heat (cool-down cycle) to ensure that
the items reach a lower temperature to avoid wrinkling.
End: take the laundry out of the dryer. The drying process is complete and the anti-
crease phase has been reached (active).
Set the programme selector knob to “Off” (“O”).
Set the programme selector knob to “Off” (“O”).
Cleaning the lint filter: open door, pull lint filter up and out of machine and open it. Brush lint using a soft brush or your
fingertips. Close lint filter and push firmly back into place (more detailed informations are given in the Instructions For Use).
Emptying the water container: pull container out by the handle and empty. Replace the container when empty by pushing it
completely back into place.
Please note: only use additives/plastic items specified as dryer safe and rinse items that have been treated with stain remover
thoroughly in plenty of water before drying. Never dry rubber objects or objects stained with vegetable oils in the dryer.
The Manufacturer is not liable for any damage to laundry resulting from inadequate or incorrect fabric care instructions which
have been provided with the garment or article.
Sort laundry according to
care symbols
Do not tumble dry
Suitable for tumble drying -
Suitable for tumble drying
at low temperatures
Prepare laundry
Load dryer
Select programme
Select options
(if available)
Start dryer
Programme end -
unload dryer
Switch dryer off
* Weight of average and maximum load.
** Test programmes according to EN 61121, tested with maximum rated load capacity.
2
Overview of programmes Options
Approximate
drying times
(in minutes)
Programmes / Drying levels
Type of textile
Fabrics
Volume
of load
kg
*
Délicat /
Gentle
Séchage+ /
Dry +
Départ
différé /
Start delay
Very
wet
load
Wet
load
Extra dry
Multi-layered, thick laundry such as: terry towels,
terry towelling bath robes.
Cotton or linen hot wash/
coloured laundry
Max. 8 kg
3.0
8.0
X X X
95’
205’
80’
180’
Cupboard dry +
Terry towels, dry towels, bed linen, underwear.
3.0
8.0
X X X
80’
190’
70’
160’
Cupboard dry **
Similar types of laundry which do not require
ironing such as: dry towels, bed linen, underwear,
baby clothes, T-shirts, cotton socks.
3.0
8.0
X X X
75’
170’
65’
145’
Iron dry **
Laundry which requires ironing such as: bed and
table linen, dry towels, T-shirts, polo shirts, work
clothes.
3.0
8.0
X X X
65’
135’
55’
115’
Cupboard dry +
Laundry with thick, multi-layered areas such as:
bed and table linen, track suits, anoraks, blankets.
Synthetic, mixed fibre or cotton easy care
(ironing not required) laundry
Max. 4 kg
1.0
4.0
X X X
40’
90’
30’
70’
Cupboard dry **
Laundry which does not require ironing such as:
shirts, blouses, T-shirts, sportswear.
1.0
4.0
X X X
40’
65’
25’
55’
Iron dry
Laundry which requires ironing such as: trousers,
dresses, skirts, shirts, blouses.
1.0
4.0
X X X
30’
60’
20’
50’
Synthetics
Low drying intensity for delicates and items such
as: trousers, dresses, shirts blouses.
Laundry made from synthetic fibres
Max. 2.5 kg
1.0
4.0
X X X 105’ 90’
Mixed load
T-shirts, blouses, towels, underwear, sportswear.
Cotton - Synthetic blend
Max. 3 kg
3.0 X X X 85’ 70’
Laundry is aired, refreshed and loosen
up for 30 minutes without heating.
All textiles.
X
20’ 30’ 40’ 60’
Additional drying time for textiles that are not
suitable for other programmes, or for finalisation
of the drying process.
X X
20’ 30’
40’ 60’
Cotton Easy care
Special
programmes
Fibres sensibles
Fibres sensibles
Mix
Mix
Airing
Fraîcheur
Drying
times
3
How to proceed if...
...you want to check the dryer yourself first: (If your machine is not functioning correctly, please
check the following points before calling the Customer Service department - also refer to relevant
section in the Instructions For Use).
Drying takes too long/
Laundry is not dry enough
Was the inserted laundry too wet (washing machine spin speed less than 1000 rpm)?
Is the lint filter dirty? (filter indicator light on)
Is the heat exchanger dirty? (for more information, refer to the Instructions For Use)
Is the room temperature too high?
Are the “End” and “Anti-crease” indicator lamps lighting up? The drying cycle is
complete and the laundry can be taken out.
If the drying result does not meet your expectation, select a drier programme or use
the dryness adjustment option (if available).
Are thin and thick laundry mixed? Are different types of materials mixed? Sort the
laundry by thickness and material, then dry it again.
The dryer does not
operate (after a power
failure, always press the
“Start (Pause)” button)
Is the plug properly inserted into the mains electricity socket?
Is there a power failure?
Has the fuse blown?
Is the door properly closed?
Has a drying programme been selected?
Has the “Start (Pause)” button been pressed?
Has the start delay option been selected?
Is the dryer overloaded? Please remove some of the load.
Lint filter or water
container indicator lamp
on
Is the lint filter clean?
Is the water container empty?
Has the water container been inserted correctly?
Is the heat exchanger clean and inserted correctly?
Water droplets
underneath the dryer
Has the heat exchanger been inserted correctly?
Has all lint on the heat exchanger seal and the door seal been wiped away?
Has the water container been inserted correctly?
If the direct drain connection is used, is it tight?
Is the dryer levelled?
...you want to care for and clean your dryer:
Clean the filter at the end
of every cycle
Brush lint using a soft brush or your fingertips.
Close the filter.
Push the filter back into place.
Empty the water container
at the end of every drying
cycle
Pull the handle to remove the water container.
Empty the water container.
Replace the empty water container by pushing it fully back into place.
Clean the heat exchanger
at least once a month
Clean the heat exchanger under running water.
Remove all lint from the seals.
Clean the heat exchanger housing (for further information see section “Cleaning
the heat exchanger” in the Instructions for Use).
4
FAILURE CODES
In case of a malfunction of the dryer, one of the following failure codes could be displayed.
Depending on the model of your dryer, the failure can be displayed in letters or by different blinking
lamps.
Failure
code
Lamps failure code
Check needed by customer before
Service call
F01
Please call the After-Sales Service.
F02
Please call the After-Sales Service.
F03
Please call the After-Sales Service.
F04
Please call the After-Sales Service.
F05
Turn OFF the dryer. Unplug the dryer. Assure that
the ambient temperature is between 5°C and
35°C. Wait for 1 hour. Plug the again and restart
the dryer. If the failure occurs again, please call
the After-Sales Service.
F06
F07
Start lamp is
blinking 2 times
per second when
it is pressed
Assure that the door is correctly closed and the heat exchanger correctly positioned.
GB
Quick Reference Guide
Before using the machine, please also read the Instructions For Use carefully!
5
AZB 8574
5019 307 01560
(Subject to technical modifications)
Indicator lamps
th
th
sense
40’
20’
30’
60’
3h 6h 9h
Prêt à porter
Prêt à repasser
Fraîcheur
Prêt à repasser
Prêt à porter
Prêt à ranger
Prêt à ranger
Séchage renforcé
Nettoyer ltreVider réservoir
Séchage Fin de cycle
Arrêt
Fabriqué en France
AZB 8574
Mix
Fibres sensibles
Départ
(Pause)
Délicat
Départ
diéré
Séchage+
Programme selector knob
The drying programme is selected by
turning this knob. The “Start (Pause)”
indicator lamp flashes.
“Start (Pause)” button
The drying programme is started by
pressing this button. The indicator lamp
lights up.
Clean filter
The indicator lamp lights up when the
filter and/or the heat exchanger and its
housing need to be cleaned.
Clean the filter at the end of every
drying cycle.
Water container
The indicator lamp lights up when the
water container needs to be emptied.
The drying cycle is automatically
interrupted. Empty the container and
restart the drying programme.
Empty the water container after
every drying cycle.
End of cycle
The drying programme is finished. Please
unload the dryer.
Overdry protection / 6
th
Sense
The indicator lights up when a humidity
controlled programme is selected, to
indicate the activated protection function.
Gentle
Selecting this option will reduce the
drying temperature. This option cannot
be selected when the “Rapid” option is
selected (if available).
Départ
(Pause)
th
th
sense
Délicat
Dry+
By selecting this option you can increase the
dryness level of the laundry.
Start delay
Delays the start of the drying cycle by 3, 6
or 9 hours.
Each time the button is pressed the delay
is increased by 3 hours.
Press the “Start (Pause)” button to
confirm the final selection and to start the
dryer.
The lamps above the programme selector
knob are flashing to indicate the selected
time.
During the countdown, the drum will
turn from time to time to redistribute the
laundry and the pump will start to pump
water in the water container.
To cancel or change the previously set
time delay, set the index of the
programme selector knob to “off”
position, or open the door.
Séchage+
Départ
diéré
3h 6h 9h
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

Whirlpool AZB 8574 Mode d'emploi

Catégorie
Machines à laver
Taper
Mode d'emploi

dans d''autres langues