Sony Musical Instrument SDP-E300 Manuel utilisateur

1

GB

3-810-850-12(1)

Operating instructions

Mode d’emploi

Manual de Instrucciones

Manual de Instruçõnes

GB

F

E

P

SDP-E300

Digital Surround

Processor

2

GB

WARNING

To prevent fire or shock

hazard, do not expose

the unit to rain or

moisture.

To avoid electrical shock, do not open

the cabinet. Refer servicing to qualified

personnel only.

Precautions

On safety

• Should any solid object or liquid fall

into the cabinet, unplug the processor

and have it checked by qualified

personnel before operating it any

further.

On power sources

• Before operating the processor, check

that the operating voltage is identical

with your local power supply. The

operating voltage is indicated on the

nameplate at the rear of the

processor.

• The processor is not disconnected

from the AC power source (mains) as

long as it is connected to the wall

outlet, even if the processor itself has

been turned off.

• If you are not going to use the

processor for a long time, be sure to

disconnect the processor from the

wall outlet. To disconnect the mains

lead, grasp the plug itself; never pull

the cord.

• The AC power cord (mains lead)

must be changed, at a qualified

service shop only.

• The mains switch is located on the

front exterior.

On placement

• Do not install the appliance in a

confined space, such as a bookcase or

built in cabinet.

• Place the processor in a location with

adequate ventilation to prevent heat

buildup and prolong the life of the

processor.

• Do not place the processor near heat

sources, or in a place subject to direct

sunlight, excessive dust or

mechanical shock.

• Do not place anything on top of the

cabinet that might block the

ventilation holes and cause

malfunctions.

On operation

• Before connecting other components,

be sure to turn off and unplug the

processor.

On cleaning

• Clean the cabinet, panel and controls

with a soft cloth slightly moistened

with a mild detergent solution. Do

not use any type of abrasive pad,

scouring powder or solvent such as

alcohol or benzine.

If you have any question or problem

concerning your processor, please

consult your nearest Sony dealer.

3

GB

TABLE OF CONTENTS

Getting Started

Unpacking 4

Hookup Overview 4

TV/VCR Hookups 5

Audio Component Hookups 5

Speaker System Hookups 6

AC Hookups 7

Processor Operations

Selecting a Component 8

Recording 11

Using Surround Sound

Choosing a Surround Mode 12

Getting the Most Out of Dolby Pro Logic Surround Sound 12

Additional Information

Troubleshooting 14

Specifications 15

Glossary 16

Index 17

Rear Panel Descriptions 17

Remote Button Descriptions 18

About This Manual

Conventions

• The instructions in this manual

describe the controls on the

processor. You can also use the

controls on the remote if they have

the same or similar names as those on

the processor.

• The “Remote Button Descriptions”

section on page 18 provides an

overview of the remote buttons.

• The following icons are used in this

manual:

Indicates that you can use only

the remote to do the task.

Indicates hints and tips for

making the task easier.

This processor has the Dolby Surround

system.

Manufactured under license from Dolby

Laboratories Licensing Corporation.

DOLBY, the double-D symbol a and

PRO LOGIC are trademarks of Dolby

Laboratories Licensing Corporation.

GB

4

GB

Hookup Overview

The processor allows you to connect and control the

following audio/video components. Follow the

hookup procedures for the components that you want

to connect to the processor on the pages specified. To

learn the locations and names of each jack, see “Rear

Panel Descriptions” on page 17.

Unpacking

Check that you received the following items with your

processor:

• Remote controller (remote) (1)

• Size AA (R6) batteries (2)

Inserting batteries into the remote

Insert two size AA (R6) batteries with the + and – on

the battery compartment. When using the remote,

point it at the remote sensor g on the processor.

When to replace batteries

Under normal use, the batteries should last for about 6

months. When the remote no longer operates the

processor, replace both batteries with new ones.

Notes

• Do not leave the remote in an extremely hot or humid

place.

• Do not use a new battery with an old one.

• Do not expose the remote sensor to direct sunlight or

lighting apparatuses. Doing so may cause a malfunction.

• If you don’t use the remote for an extended period of time,

remove the batteries to avoid possible damage from

battery leakage and corrosion.

Rear

speaker

(L)

Rear

speaker

(R)

TV

TV/VCR Hookups (5)

Centre

speaker

Control Amplifier,

CD player, etc...

Audio Component

Hookups (5)

Active

woofer

VCR

LD player

Amplifier

for front

speakers

Speaker System

Hookups (6)

Before you get started

• Turn off the power to all components before making

any connections.

• Do not connect the mains lead until all of the

connections are completed.

• Be sure to make connections firmly to avoid hum

and noise.

• When connecting an audio/video cable, be sure to

match the colour-coded pins to the appropriate jacks

on the components: Yellow (video) to Yellow; White

(left, audio) to White; and Red (right, audio) to Red.

Getting Started

5

GB

Getting Started

VCR

VCR or LD player

Audio Component Hookups

Overview

This section describes how to connect either an entire

audio system or an individual audio component to the

processor so you can listen to stereo sources in

surround sound.

For specific locations of the jacks, see the illustration

below.

What cords will I need?

Audio cord (not supplied) (1)

TV INVIDEO 2

VIDEO 1

White (L)

Yellow

Red (R)

White (L)

Yellow

Red (R)

Red (R)Red (R)

White (L)White (L)

Yellow

TV/VCR Hookups

Overview

This section describes how to connect video

components to the processor. For specific locations of

the jacks, see the illustration below.

What cables will I need?

• Audio/video cable (not supplied) (2 for the VCR, and 1

for an additional VCR or LD player)

• Audio cable (not supplied) (1 for the TV)

• Video cable (not supplied) (1 for the MONITOR or TV)

Hookups

The arrow ç indicates signal flow.

Monitor (TV)

TV

MONITOR OUT

OUTPUT

VIDEO

AUDIO

INPUT

VIDEO

AUDIO

L

R

L

R

VIDEO 1

AUDIO

OUT

IN

VIDEO

OUT

IN

Processor

VIDEO 2

AUDIO

IN

VIDEO

IN

L

R

OUTPUT

VIDEO

AUDIO

L

R

LINE IN

Red (R)Red (R)

White (L)White (L)

(continued)

VCR

Processor VCR or LD player

MONITOR

OUT

INPUT

VIDEO

Processor

Monitor (TV)

L

R

TV

OUTPUT

AUDIO

L

R

AUDIO

IN

Processor

TV

6

GB

Getting Started

What cords will I need?

Audio cord (not supplied) (1) (for the amplifier powering

the front speakers)

What cords will I need?

Speaker cord (not supplied) (1 for each rear speaker and one

for the centre speaker)

Twist the stripped ends of the cord about 2/3 inch (15 mm).

Be sure to match the speaker cord to the appropriate

terminal on the components: + to + and – to –. If the cords

are reversed, the sound will be distorted and will lack bass.

Hookups

Front speakers

Rear and centre speakers

Active woofer

Processor

LINE

AUDIO

IN

L

R

PRE OUT

L

R

Red (R)Red (R)

White (L)White (L)

(+)

(–)

Rear speaker

(R)

Centre speaker

Rear speaker

(L)

Processor

} ]

SPEAKERS

REAR

LR

CENTER

45°

60 - 90 cm

Rear

Front

FRONT OUT

REAR SPEAKERS

CENTER SPEAKERSSURROUND

REAR/CENTER out

SURROUND

MIX out

Control Amplifier

Processor

LINE

AUDIO

IN

L

R

LINE OUT

L

R

L

R

FRONT

OUT

AUX

INPUT

L

R

Processor

Amplifier

(for front speakers)

CD Player (etc.)

Hookups

The arrow ç indicates signal flow.

Audio system

Connect the PRE OUT, ADAPTER OUT, or TAPE REC jacks

on your control amplifier to the LINE IN jacks on the

processor.

CD player (etc.)

Connect the LINE OUT jacks on your CD player (etc.) to the

LINE IN jacks on the processor.

Speaker System Hookups

Overview

This section describes how to connect your speakers to

the processor. Although you can connect rear and

centre speakers directly to the processor, front speakers

must be connected through a separate amplifier (as

shown below). Connecting an active woofer will

increase bass response.

For specific locations of the terminals, see the

illustration below.

For optimum surround sound effect, place your

speakers as shown below.

Processor

Active woofer

REAR

SURROUND

MIX

CENTER

INPUT

7

GB

Getting Started

• If you need an even more powerful sound

You can connect the rear and centre speakers through

additional amplifiers using the SURROUND REAR out

and SURROUND CENTER out pin jacks.

Rear speakers

If you want to use a wireless rear speaker system

Use the SURROUND REAR out pin jacks.

Centre speaker

Processor

AC Hookups

Connecting the mains lead

Connect the mains lead from this processor and from

your audio/video components to a wall outlet.

Before You Use Your Processor

Make sure that you have turned MASTER VOLUME to

the leftmost position (0).

/

to a wall

outlet

AUX

INPUT

L

R

REAR

SURROUND

MIX

CENTER

L

R

Processor

INPUT

REAR

SURROUND

MIX

CENTER

Amplifier

(for centre speaker)

Amplifier

(for rear speakers)

Processor Operations

8

GB

Watching video programmes

To take full advantage of the processor’s surround

sound effects, like Dolby Surround, turn off the

speakers on your TV before you start. This also lets you

use the processor’s remote to control the audio.

To watch TV programmes, do the following:

1 Turn on your TV.

2 Turn on the processor and press TV.

3 Turn on the amplifier for the front speakers and

set it’s function selector to AUX.

(If you connected the FRONT OUT jacks to the

amplifier’s AUX IN jacks).

To watch videos or laser discs, do the following:

1 Turn on your VCR or LD player.

2 Turn on the processor and press VIDEO 1 (to

watch a video).

3 Turn on the amplifier connecting the front

speakers and set it’s function selector to AUX.

(If you connected the FRONT OUT jacks to the

amplifier’s AUX IN jacks).

Using the remote

The remote lets you operate the processor and the Sony

components that are connected to it.

1 Press one of the SYSTEM CONTROL/

FUNCTION buttons to select the component you

want to use. When the processor is in STANDBY

mode, the power turns on and the input switches

to the component you selected.

POWER MASTER VOLUME

Function buttons

To listen to or watch

Video tapes

TV programmes

Laser discs (or video tapes)

Records, Radio programmes,

Compact discs (CD),

Audio tapes, or MiniDiscs (MD)

Do this

Press MUTING. Press again to

restore the sound

Press BASS BOOST to turn on

the BASS BOOST indicator.

To

Mute the sound

Reinforce the bass

Selecting a Component

To listen to or watch a connected component, first

select the function on the processor or with the remote.

Before you begin, make sure you have:

• Connected all components securely and correctly as

indicated on pages 5 to 7.

• Turned MASTER VOLUME to the leftmost position

(0) to avoid damaging your speakers.

1 Press POWER to turn on the processor.

Using SYSTEM OFF on the remote puts the

processor in STANDBY mode. Press one of the

Function buttons to turn on the power, using the

processor, when it is in STANDBY mode.

2 Press a function button to select the component

you want to use:

* If you connected your audio amplifier to the LINE

IN jacks on the processor as shown on page 6, use

the function selector on the amplifier to select the

component you want to listen to (“CD” for example).

3 Turn on the component, the VCR for example,

and start playback.

4 Turn MASTER VOLUME to adjust the volume.

Press

VIDEO 1

TV

VIDEO 2

LINE*

SYSTEM

CONTROL/

FUNCTION

SYSTEM

OFF

VISUAL

POWER

9

GB

Processor Operations

The SYSTEM CONTROL/FUNCTION buttons on

the remote are factory-set as follows:

To listen to Press

Records PHONO*

Radio programmes TUNER*

Compact discs (CD) CD*

Audio tapes (Tape deck B) TAPE*

VHS Video tapes VIDEO 1

(Remote control mode VTR 3)

Laserdiscs VIDEO 2

TV programmes TV

Other components LINE**

* The input selector switches to LINE IN. If you

connect a Sony amplifier (that can be controlled by

infrared wireless remote) to the LINE IN jacks of

the processor, the amplifier’s input selector

automatically switches to the selected component.

** If you connected an additional audio component to

the LINE jacks as shown on page 6.

If you want to change the factory setting of a

button, see page 10.

If the component does not turn on

Press the power switch on the component.

2 Start playing.

Refer to “Remote Button Descriptions” on page 18

for details.

To turn off the components

Press SYSTEM OFF.

If you use a Sony TV

When you press TV to watch a TV programme, the TV

turns on and switches to the TV input. The TV also

turns on when you press VIDEO 1 or VIDEO 2 and

switches to the appropriate video input.

If the TV does not switch to the appropriate input

automatically, press TV/VIDEO on the remote.

Operating one component while using

another (Background Operation)

You can temporality operate other components while

listening to or watching a programme.

1 Hold down BACKGROUND.

2 Press both the corresponding numeric button of

the component you’re going to use (see the table

below) and one of the following buttons at the

same time; VISUAL POWER, TV/VIDEO, CH

PRESET +/–, ANT TV/VTR, D.SKIP, (, 9, p,

0 / ) , = / + , P , r .

Example:To start recording on the VCR while

watching TV.

While holding down BACKGROUND,

press 9 (or 8) and press r at the same

time.

The numeric buttons are assigned to select the

functions as follows:

* Sony VCRs are operated with a VTR 1, 2 or 3 setting.

These correspond to Beta, 8mm and VHS respectively.

Numeric buttons

BACKGROUND

Numeric button

1

2

3

4

5

6

7

8

9

0

Operates

CD player

DAT deck

MD deck

Tape deck A

Tape deck B

LD player

VCR (remote control mode VTR 1*)

VCR (remote control mode VTR 2*)

VCR (remote control mode VTR 3*)

TV

(continued)

Processor Operations

10

GB

Numeric buttons

SYSTEM

CONTROL/

FUNCTION

LEARN

Other remote

Processor remote

About 2 inches

(5 cm)

Changing the factory setting of a

function button

If the factory settings of the FUNCTION buttons don’t

match your system components, you can change them.

For example, if you have a VHS VTR and a 8mm VTR,

you can assign the VIDEO 2 button to operate you

8mm VTR. Note that the settings of the LINE, TUNER

and PHONO buttons cannot be changed.

1 Hold down the SYSTEM CONTROL/FUNCTION

button whose function you want to change

(VIDEO 2, for example).

2 Press the corresponding numeric button of the

component you want to assign to the SYSTEM

CONTROL/FUNCTION button (8 = 8mm VTR,

for example).

For the numeric buttons, see the table in

“Operating one component while using another”

on page 9.

Now you can use the VIDEO 2 button to control a

8mm VTR.

To reset the setting to the factory setting

Repeat the above procedure.

Programming the Remote

The RM-PE300 remote included with the SDP-E300 can

control non-Sony components by “learning” the

control signals from their remotes. Once this remote

learns the other components signals, you can use these

components as part of your system. Additionally, if

you have any Sony components that fail to operate

with this remote, use this programming function. This

remote can “learn” signals only from other infrared

wireless remotes. Before you programme signals, make

sure that the two remotes:

• Face straight at each other (see Step 3 below)

• Are placed at a distance of about 2 inches (5 cm)

• Are not moved during programming

SYSTEM

CONTROL/

FUNCTION

You can programme signals from other remote controls

to the shadded buttons shown below.

1 Press the SYSTEM CONTROL/FUNCTION

button of the component you want to programme.

For example, if you want to programme a CD

player’s remote, press CD.

2 Press LEARN to turn on the LEARN indicator.

3 Press the button on this unit’s remote that is to

“learn” the signal from the other remote.

The LEARN indicator flashes slowly.

Be sure to use only the shadded buttons shown

above (see “Remote Button Descriptions” on page

18 for the buttons you can use to operate each

component).

If the LEARN indicator flashes rapidly

You cannot use the button you’ve pressed.

4 On the other remote, select the function that the

processor’s remote is to “learn” and hold down its

button until the LEARN indicator lights steadily.

5 Repeat Steps 3 and 4 to programme other buttons.

Note that each button can only “learn” one signal

from another remote.

6 Press LEARN.

After the LEARN indicator turns off, you can

control the other component with the

programmed buttons.

LEARN

indicator

BACKGROUND

11

GB

Processor Operations

When you programme the recording signal

While holding down the r button on the processor’s

remote and press the record button on the other remote.

If you cannot successfully programme signals, check

the following:

• If the LEARN indicator does not light up at all, the

batteries are weak. Replace both batteries.

• If the LEARN indicator does not flash or light up in

Step 3 or 4, there is interference. Clear the signal as

described in “Clearing the programmed signal”

below and programme again from the beginning.

• The two remotes are placed too far apart. Make sure

they are only 2 inches apart.

• If you don’t proceed to the following steps within

about 1 minute during Steps 2 and 3, the remote

automatically exits learning mode. Start again from

Step 2.

• If the memory in the remote has become full, (If you

programme signals of Sony components, you can

store about 30 signals.) You can programme a new

signal on a previously programmed button, but the

new signal will replace the previously programmed

one.

Notes

• You cannot turn on programmed components by pressing

a SYSTEM CONTROL/FUNCTION button. You have to

turn on the component’s power switch.

• Do not programme remote signals of air conditioners or

other household appliances.

Clearing the programmed signal

To clear the programmed signals, do the following.

The button’s functions are reset to the factory-preset.

1 Press LEARN to turn on the LEARN indicator.

2 While holding down BACKGROUND, hold down

the button to be cleared until the LEARN

indicator turns off.

Recording

This processor makes it easy to record to and from the

components connected to the processor. You don’t

have to connect playback and recording components

directly: once you select a programme source on the

processor, you can record and edit as you normally

would using the controls on each component.

Before you begin, make sure you’ve connected all

components properly.

ç: Audio signal flow

c: Video signal flow

Recording on a video tape

You can record from a LD player using the processor.

You can also add audio from a variety of audio sources

when editing a video tape.* See your VCR or LD

player’s instruction manual if you need help.

* If you connect a stereo system, or an individual audio

component, to the LINE IN jacks as shown on page 6.

1 Press VIDEO 2 (if an LD player is connected to the

VIDEO 2 jacks) to select the programme source.

2 Set the component to be ready for playing.

For example, insert the laser disc you want to

record from into the LD player.

3 Insert a blank video tape into the VCR for

recording.

4 Start recording on the VCR and then start playing

the laser disc you want to record.

You can replace audio while copying a laser disc

At the point you want to start adding different sound,

press LINE (if an audio component system is connected

to the LINE IN jacks, be sure to select the proper source

beforehand) and start playback. The sound from the

selected component will be recorded over the original

audio.

To resume recording the sound of the laser disc, press

the VIDEO 2 function button.

Playback component

(programme source)

c

ç

c

Recording

component

(VCR)

Function buttons

Using Surround Sound

12

GB

Choosing a Surround Mode

You can take advantage of surround sound simply by

selecting one of the three pre-programmed surround

modes according to the type of programme you wish

to play.

1 Press SURROUND MODE to turn on the

surround sound.

One of the SURROUND indicators lights up in the

display.

2 Press SURROUND MODE repeatedly until the

indicator for the surround mode you want lights

up.

Select the appropriate surround mode as follows:

To turn off surround sound

Press SURROUND ON/OFF on the remote.

You can find Dolby Surround-encoded software by

looking at the packaging

However, some videos and laser discs may use Dolby

Surround sound even if it’s not indicated on the

package.

Getting the Most Out of Dolby

Pro Logic Surround Sound

To obtain the best possible Dolby Pro Logic Surround

sound, first select the centre mode according to the

speaker system you have. Then, adjust the volume of

each speaker.

Note that you must connect the rear speakers and/or

one centre speaker to do the following adjustments.

SURROUND MODE

To

Decode programmes processed with Dolby

Surround and create the atmosphere of a

movie theatre.

Reproduce the acoustics of a movie

theatre. Ideal for soft, acoustic sounds.

Create a simulated surround sound from

monaural sources such as old movies or

TV programmes.

Select

PRO LOGIC

THEATER

SIMULATED

SURROUND

Indicators

CENTER MODE

Indicators

LEVEL

Indicators

SURROUND MODE

EFFECT –/+

SURROUND

ON/OFF

SURROUND

Modes

SURROUND

ON/OFF

TEST TONE

REAR

LEVEL +/–

EFFECT –/+

CENTER

LEVEL +/–

13

GB

Using Surround Sound

Selecting the centre mode

The processor offers you four centre modes: Phantom,

Normal, Wide, and 3 Channel Logic. Each mode is

designed for a different speaker configuration. Select

the mode that best suits your speaker’s system

configuration:

1 Press SURROUND MODE repeatedly to select the

PRO LOGIC sound field.

2 Press CENTER MODE repeatedly until the

indicator for the centre mode you want lights in

the display.

* Select the centre mode as follows:

* The CENTER MODE indicator may not light

immediately when using SURROUND MODE on the

amplifier to selecting the surround mode.

So that

The sound of the

centre channel is

output from the front

speakers.

The bass sound of the

centre channel is

output from the front

speakers (because a

small speaker cannot

produce enough

bass).

For “complete”

Dolby Pro Logic

Surround sound.

The sound of the rear

channel is output

from the front

speakers.

If you have

Front and rear

speakers, no

centre speaker

Front and rear

speakers, and a

small centre

speaker

Front and rear

speakers, and a

large centre

speaker

Front and centre

speakers, no rear

speaker

Select

PHANTOM

NORMAL

WIDE

3 CH LOGIC

(3 Channel

Logic)

Adjusting the speaker volume

The test tone feature lets you set the volume of your

speakers to the same level.

You can only use the test tone when the surround

mode is set to Pro Logic.

Using the controls on the remote lets you adjust the

volume level from your listening position.

1 Press TEST TONE on the remote.

You will hear the test tone from each speaker

sequentially.

2 Adjust the volume level so that the test tone from

each speaker is at the same level from your

listening position.

• To adjust the level of centre speaker, press

CENTER LEVEL + or – on the remote.

• To adjust the level of rear speakers, press

REAR LEVEL + or – on the remote.

3 Press TEST TONE on the remote to turn off the

test tone.

You can adjust all speakers at one time

Adjust MASTER VOLUME on the processor or remote.

Note

The centre and rear levels are indicated on the LEVEL meter

in the centre of the display during adjustment.

Adjusting the Effect Level

(for THEATER and SIMULATED only)

You can make the surround sound more prominent by

increasing the EFFECT level. This control lets you

adjust the “presence” of the surround effect in five

steps (1-5).

1 Start playing a programme source.

2 Use EFFECT (–/+) to select the level you prefer.

The effect level is indicated on the LEVEL meter

in the centre of the display.

Note

Changing the effect level may not produce major variations

in the surround effect when used with certain playback

sources.

14

GB

Additional Information

Troubleshooting

If you experience any of the following difficulties while

using the processor, use this troubleshooting guide to

help you remedy the problem. Should any problem

persist, consult your nearest Sony dealer.

There’s no sound or only a very low-level sound is heard.

/ Check that the speakers and components are

connected securely.

/ Press MUTING if the MUTING indicator

turns on.

/ Make sure you select the correct component

on the processor.

/ Make sure you select the correct component

on the amplifer for the front speakers.

The left and right sounds are unbalanced or reversed.

/ Check that the speakers and components are

connected correctly and securely.

Severe hum or noise is heard.

/ Check that the speakers and components are

connected securely.

/ Check that the connecting cords are away

from a transformer or motor, and at least 10

feet (3 meters) away from a TV set or

fluorescent light.

/ Place your TV away from the audio

components.

/ The plugs and jacks are dirty. Wipe them

with a cloth slightly moistened with alcohol.

No sound or only a very low-level sound is heard from

the rear speakers.

/ Select the appropriate centre mode (see page

13).

/ Adjust the speaker volume appropriately (see

page 13).

/ Make sure you turned on the surround mode.

No sound is heard from the centre speaker.

/ Select the appropriate centre mode (see page

13).

/ Adjust the speaker volume appropriately (see

page 13).

Surround effect cannot be obtained.

/ Make sure you turn on the surround mode.

No picture or an unclear picture is seen on the TV screen.

/ Select the appropriate function on the

processor.

/ Place your TV away from the audio

components.

Recording cannot be made.

/ Check that the components are connected

correctly.

The remote does not function.

/ Point the remote at the remote sensor g on

the processor.

/ Remove the obstacles in the path of the

remote and the processor.

/ Replace both batteries in the remote with new

ones if they are weak.

/ Make sure you select the correct function on

the remote.

The CENTER MODE indicator does not light immediately.

/ The CENTER MODE indicator may not light

immediately when using SURROUND MODE

on the amplifier to selecting the surround

mode.

15

GB

Additional Information

Specifications

Amplifier section

Power output

Surround mode

Frequency

response

(DIN 1 kHz)

Centre:

40 W/8 ohms

(only in the PRO LOGIC

and THEATER modes)

Rear:

20 W + 20 W/8 ohms

VIDEO 1 + 2, TV, LINE:

20 Hz - 20 kHz ±2 dB

Inputs

Sensitivity

150 mV

Impedance

50

kilohms

VIDEO 1,

VIDEO 2,

TV, LINE

VIDEO 1 REC:

Voltage 150 mV,

Impedance 470 ohms

FRONT, CENTER, REAR,

MIX:

Voltage: 1 V

Impedance: 1 kilohms

+7 dB at 60 Hz

VIDEO 1, VIDEO 2,

TV, LINE:

1 Vp-p 75 ohms

VIDEO 1 REC,

VIDEO MONITOR:

1 Vp-p 75 ohms

Outputs

BASS BOOST

Inputs

Outputs

Video section

Audio section

General

220 - 230 V AC, 50/60 Hz

90 W

430 x 95 x 280 mm

(17 x 3

3

/4 x 11

1

/8 in)

4.6 kg

(10 lb 2 oz)

Remote controller

(remote) (1)

Size AA (R6) batteries (2)

Power

requirements

Power

consumption

Dimensions

Mass (Approx.)

Supplied

accessories

Design and specifications are subject to

change without notice.

16

GB

Additional Information

Early reflections

Glossary

Centre mode

Setting of speakers to enhance Dolby Pro

Logic Surround mode. To obtain the best

possible surround sound, select one of the

following four centre modes according to

your speaker system.

• NORMAL mode

Select NORMAL mode if you have front

and rear speakers and a small centre

speaker. Since a small speaker cannot

produce enough bass, the bass sound of

the centre channel is output from the front

speakers.

• WIDE mode

Select WIDE mode if you have front and

rear speakers and a large centre speaker.

With the WIDE mode, you can take full

advantage of Dolby Surround sound.

• PHANTOM mode

Select PHANTOM mode if you have front

and rear speakers but no centre speaker.

The sound of the centre channel is output

from the front speakers.

• 3 CH LOGIC mode

Select 3 CH LOGIC mode if you have front

and centre speakers but no rear speaker.

The sound of the rear channel is output

from the front speakers to let you

experience some of the surround sound

without using rear speakers.

Dolby Pro Logic Surround

Decoding system of Dolby Surround sound

standardized in TV programmes and movies.

Compared with the former Dolby Surround

system, Dolby Pro Logic Surround improves

sound image by using four separate channels:

off-screen audio effects, on-screen dialog,

left-to-right panning, and music. These

channels manipulate the sound to be heard

and enhance the action as it happens on the

screen. To take advantage of Dolby Pro Logic,

you should have at least one pair of rear

speakers and/or one centre speaker. You also

need to select the appropriate centre mode to

enjoy a full effect.

Dolby Surround

Encoding and decoding system of Dolby

Surround sound for consumer use. Dolby

Surround decodes the extra channels on the

Dolby Surround-encoded sound tracks of

movie videos and TV programmes and

produces sound effects and echoes that make

the action seem to envelop you.

The processor offers Dolby Surround as one

of the pre-programmed sound fields. If you

have rear or centre speaker(s), we

recommend that you customize the Dolby

Surround sound field by selecting the

appropriate centre mode to take advantage of

Dolby Pro Logic Surround sound.

Surround sound

Sound that consists of three elements: direct

sound, early reflected sound (early

reflections) and reverberative sound

(reverberation). The acoustics where you hear

the sound affect the way these three sound

elements are heard. These sound elements are

combined in such a way that you can actually

feel the size and the type of a concert hall.

Centre

speaker

Rear

speaker (R)

Rear

speaker (L)

Front

speaker (R)

Front

speaker (L)

Centre

speaker

Rear

speaker (R)

Rear

speaker (L)

Front

speaker (R)

Front

speaker (L)

Front

speaker (L)

Front

speaker (R)

Rear

speaker (R)

Rear

speaker (L)

Centre

speaker

Front

speaker (R)

Front

speaker (L)

Reverberation

Direct sound

Early

reflections Reverberation

Level

Early reflection time

Time

3 CH LOGIC

Centre

Front (R)

Front (L)

NORMAL/WIDE

Rear (L, R)

PHANTOM

Front (L, R)

Direct sound

• Types of sound

• Transition of sound from rear speakers

Test tone

Signal given out by the processor for

adjusting the speaker volume. The test tone

will come out as follows:

• In a system with a centre speaker

(NORMAL/WIDE/3 CH LOGIC modes)

The test tone is output from the front L

(left), centre, front R (right), and rear

speakers in succession.

• In a system without a centre speaker

(PHANTOM mode)

The test tone is output from the front and

the rear speakers alternately.

17

GB

E, F, G

Editing. See Recording

H, I, J, K, L, M

Hookups

audio components 5

mains lead 7

overview 4

speakers 6

TV/VCRs 5

N, O

NORMAL mode 13, 16

P, Q

PHANTOM mode 13, 16

Programme source

selecting 8, 9

Programming the remote 10

R

Rear panel 5, 6, 7, 17

Recording

on a video tape 11

Remote buttons 8, 9, 10, 12, 18

background operation 9

S

Selecting a programme source

8

using the remote 8

Speakers

connection 6

impedance 15

placement 6

Surround sound 12, 13, 16

T

Test tone 13, 16

3 CH LOGIC mode 13, 16

Troubleshooting 14

TV/VCR hookups 5

U, V

Unpacking 4

W, X, Y, Z

Watching video programmes

8

WIDE mode 13, 16

Index

A

Adjusting

effect level 13

speaker volume 13

volume 8

Audio component hookups 5

B

Background operation 9

C

Centre mode 13, 16

NORMAL mode 13, 16

PHANTOM mode 13, 16

3 CH LOGIC mode 13, 16

WIDE mode 13, 16

Connecting. See Hookups

D

Dolby Pro Logic

Surround 16

getting the most out of 12

Dolby Surround sound 12, 16

centre mode 13, 16

Dubbing. See Recording

1 LINE (AUDIO) IN

2 VIDEO 2 IN

3 VIDEO 1 IN/OUT

4 MONITOR OUT

5 TV (AUDIO) IN

6 FRONT OUT

7 SURROUND REAR out

8 SURROUND CENTER out

9 SURROUND MIX out

0 SPEAKERS (REAR)

!¡SPEAKER (CENTER)

!™ mains lead

Rear Panel Descriptions

!™

0!¡54623 7891

18

GB

Remote Button Descriptions

For buttons not described on previous pages and buttons with names different from the buttons on the main unit.

Operates

Receiver

CD player/MD

recorder/LD

player

TV/VCR

CD player/

Tape deck/

LD player/

MD recorder

Receiver

TV/VCR

CD player

Tape deck/MD

recorder/VCR/

LD player

CD player/

MD recorder/

LD player

VCR

CD player/

Tape deck/MD

recorder/LD

player/VCR

CD player/

Tape deck/MD

recorder/LD

player/VCR

CD player/

Tape deck/MD

recorder/LD

player/VCR

Tape deck

Tape deck/

MD recorder

Tape deck/

VCR

Function

Selects preset numbers.

Selects track numbers.

0 selects track 10.

Selects channel numbers.

Selects track numbers

over 10.

Scans and selects preset

stations.

Selects preset channels.

Skips discs (CD player

with multi-disc changer

only.)

Searches tracks (forward

or backward).

Fastforwards or rewinds.

Skips tracks.

Index search

Pauses play or record.

(Also starts recording

with components in

record standby.)

Starts play.

Stops play.

Starts play on the reverse

side (for auto-reverse

decks).

Sets tape decks to the

record standby mode.

Starts recording when

pressed with ( (or 9

on tape deck).

Remote

Button

0-9

>10

CH/PRESET

+/–

D. SKIP

0 / )

= / +

P

(

p

9

r

r + (

Operates

Tape deck

TV/VCR

TV/VCR/LD

player

TV

VCR

Function

Selects tape direction (for

tape decks with the RMS*

function.)

Clears RMS* programme

(for tape decks with the

RMS function.)

Programmes tracks (tape

deck with the RMS*

function only).

Changes channels when

used with 0-9.

Selects input signal: TV

input or video input.

Press this button followed

by the SYSTEM

CONTROL/FUNCTION

button of the visual

component you want to

turn off.

Selects the channel entry

mode, either one or two

digit.

Selects preset channels for

the small picture.**

Changes the position of

the small picture.**

Swaps the small and the

large picture.**

Activates the picture-in-

picture function.**

Selects output signal from

the aerial terminal: TV

signal or VCR

programme.

Remote

Button

RMS

DIRECTION

RMS CLEAR

RMS/START

ENTER

TV/VIDEO

VISUAL

POWER

-/- -

SUB CH +/–

POSI

SWAP

P IN P

ANT TV/VTR

Remote Button Descriptions

* RMS: Random Music Sensor

** Only for Sony TVs with the picture-in-picture function

2

F

Précautions

Sécurité

• Si un solide ou un liquide tombait

dans le coffret, débranchez le

processeur et faites-le vérifier par un

technicien qualifié avant de le

remettre en service.

Sources d’alimentation

• Avant de mettre le processeur en

service, vérifiez que la tension de

fonctionnement correspond à celle du

courant secteur local. La tension de

fonctionnement est indiquée sur la

plaque signalétique à l’arrière du

processeur.

• Le processeur n’est pas déconnecté de

la source d’alimentation tant qu’il est

branché sur une prise murale, même

si vous le mettez hors tension.

• Si vous ne comptez pas utiliser le

processeur pendant un certain temps,

débranchez-le de la prise murale.

Pour débrancher le cordon, tirez sur

la fiche et jamais sur le cordon

proprement dit.

• Si le cordon d’alimentation secteur

doit être remplacé, faites appel à un

professionnel uniquement.

• L’interrupteur d’alimentation se

trouve sur le panneau avant.

Installation

• N’installez pas le processeur dans un

espace confiné comme dans une

bibliothèque ou un meuble encastré.

• Installez le processeur dans un

endroit bien ventilé pour éviter tout

risque de surchauffe interne et

prolonger la durée de vie des

composants.

• N’installez pas le processeur près

d’une source de chaleur, dans un

endroit en plein soleil, poussiéreux

ou exposé à des chocs mécaniques.

• Ne posez rien sur le coffret qui puisse

bloquer les orifices de ventilation et

provoquer un mauvais

fonctionnement.

Fonctionnement

• Avant de raccorder d’autres

appareils, mettez le processeur hors

tension et débranchez-le.

Nettoyage

• Nettoyez le coffret, le panneau et les

commandes avec un chiffon doux

légèrement imprégné d’une solution

détergente neutre. N’utilisez pas de

tampon abrasif, poudre à récurer ou

solvant, comme de l’alcool ou de la

benzine.

En cas de question ou de problème

concernant le processeur, consultez le

revendeur Sony le plus proche.

AVERTISSEMENT

Afin d’éviter tout risque

d’incendie ou

d’électrocution, éviter

d’exposer l’appareil à la

pluie ou à l’humidité.

Afin d’écarter tout risque

d’électrocution, garder le coffret fermé.

Ne confier l’entretien de l’appareil qu’à

un personnel qualifié.

3

F

Au sujet de ce

manuel

Conventions

• Ce mode d’emploi décrit les

commandes du processeur. Vous

pouvez également utiliser les

commandes de la télécommande qui

ont un nom identique ou similaire à

celles du processeur.

• Le paragraphe “Description de la

télécommande” à la page 18 fournit

une description des commandes de la

télécommande.

• Les icônes suivants sont utilisés dans

ce manuel:

Indique que vous ne pouvez

utiliser que la télécommande

pour effectuer cette opération.

Donne des conseils

supplémentaires pour faciliter

l’utilisation.

Ce processeur utilise le système

surround Dolby.

Fabriqué sous licence de Dolby

Laboratories Licensing Corporation.

DOLBY, le symbole double-D aet PRO

LOGIC sont des marques de Dolby

Laboratories Licensing Corporation.

TABLE DES MATIÈRES

Préparatifs

Déballage 4

Description des raccordements 4

Raccordement d’un téléviseur/magnétoscope 5

Raccordement de composants audio 5

Raccordement d’enceintes 6

Raccordement au courant secteur 7

Fonctionnement du processeur

Sélection d’un composant 8

Enregistrement 11

Ecoute du son surround

Choix d’un mode surround 12

Utilisation optimale du son surround Dolby Pro Logic 12

Informations supplémentaires

Guide de dépannage 14

Spécifications 15

Glossaire 16

Index 17

Nomenclature du panneau arrière 17

Description de la télécommande 18

F

La page charge ...

Sony Musical Instrument SDP-E300 Manuel utilisateur

Ce manuel convient également à

Sony Musical Instrument SDP-E300 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents